1 2 3 4 5 6 7

I ! yng
FIXTURE OUTRIGGER HANGER WIRE U 4 W
(2 TOP) OBSTRUCTION GFCI
LIGHTS: RECEPTACLE
PROVIDE TWO ON TOP, (WITH WEATHER PROOF DRYWALL
SIX AT HANDRAIL COVER) CROSS TEE
F REFER TO FAA
CIRCULAR 70/7460-1K SEE SITE LIGHT DETAIL o
FOR COMPLETE POLESHALL BESQUAREOR THIS SHEET
O RD. TAPERED. POLE AND BASE
REQUIREMENTS
PLATE SHALL BE FABRICATED
OF ALUMINUM ALLOY OR
STEEL. ALUMINUM ALLOY ANCHOR BOLTS
DRYWALL SCREW MATERIALS SHALL BE ANODIZED WITH HEAVY HEX
AND STEEL MATERIALS SHALL ASTM-A307 STEEL z
GYPSUM BOARD p.. BE HOT DIPPED GALVANIZED NUT AND WASHER 1"C(PVC) O
NOTE: I INSIDE AND OUT. FURNISH
HANDHOLE AND ALL MOUNTING 1/4" GALV.
1. SEE LAY-IN MOUNTING LED LIGHT DETAIL SETTING PLATE
FOR CONDUIT AND JUUNCTION BOX I HARDWARE.
O
RECESSED MOUNTED DETAILS. Z
z
(7) L20 WORK
LIGHTS
LED LIGHT DETAIL O
FINISH GRADE LINE BID SET

(SEE SHEET E-0108 L12 NO SCALE

FOR LOCATIONS) LL
o
. ..e.. - c UNDISTURBED EARTH OR
COMPACTED GRANULAR $
E - - -" - FILL, ALL AROUND p
HANDHOLE WITH FRAME AND
COVER GROUNDING NUT OR
LUG WELDED TO INSIDE OF ON PO E
POLE. ACCESSIBLE FROM 4-#8 VERTICAL . - 2'-6" DIAMETER OR
THE HANDHOLE. WITH .a ... SQUARE, 4000 PSI
3/4" MINIMUM CONDUIT. #3 TIES AT 18" " " ..""a CONCRETE BASE

FINISH GRADE 4" DIA. MIN. 3/4" X 10'-0" . .

COPPER
CLAD GROUND ROD
'--'-' --'-'-
HANGER ASSEMBLY FOR BOLT COVER
RODS (AS REQUIRED)

c·¬ e-¬ c-¬ c-¬ c-¬ 3/4" LIQUID-TIGHT FLEXIBLE

METAL CONDUIT WITH
CONNECTORS ONEACHEND.
WASHWATER ELEVATED STORAGE LUMINAIRE
TANK LAYOUT ANCHOR BASE-SEE
D NOSCALE FOUNDATION DETAIL
MOUNT 12' A.F.F. THIS SHEET
PROVIDE OBSTRUCTION LIGHTS, CONTROLLER, MOUNTING HARDWARE,
ETC., FOR FULLY FUNCTIONAL OBSTRUCTION LIGHTS SYSTEM.
PENDANT MOUNTED STANDARD POLE
>-
I
PROVIDE WORK LIGHTS FOR MAINTENANCE. LED LIGHT DETAIL TYPICAL YARD LIGHTING DETAIL FOUNDATION DETAIL
l-- NO SCALE L15 NO SCALE NO SCALE
O
L2
< L3

<
N
< SECURITY CAMERA AND
STRAP CONDUIT WITHIN 3' OF MOUNT BY SECURITY
BOX & A MAX OF 10' THERE CONTRACTOR
o AFTER AS PER N.E.C.
(TYP)
1/2" FLEXIBLE CONNECTION TO ....... 14 GAUGE STEEL MOUNTING PLATFORM
< FIXTURE (MIN 18" & MAX. 72" LONG)- OR BACK BOX
æ C ATTACH TO STRUCTURE TO PREVENT

EXTo!
FLEX FROM RESTING ON CEILING
<

O
O
LIGHTING FIXTURE SUPPORT WIRE
SHEET STEEL JUNCTION BOX ATTACHED TOSTRUCTURAL MEMBERS
e e a a e e a

(WITH FLAT COVER WITH KNOCKOUT) SO THAT FIXTURE IS SUPPORTED ELECTRICAL e e a a e e a

INDEPENDENT OF CEILING. WIRE TO BE CONTRACTOR

3/4" CONDUIT MINIMUM A MIN. OF #14 GAGE
PRESTRAIGHTENED GALV. ATTACHED @ POLE SHALL BE ROUND
ALL FOUR TAPERED. POLEAND BASE
o
o - CORNERS. (SEE NOTE #1) PLATE SHALL BE FABRICATED *1/2" LIQUID-TIGHT FLEXIBLE METAL
a z OF GALVANIZED POWDER CONDUIT WITH CONNECTORS ON
COATED WHITE STEEL. STEEL :::::::. EACH END.
ELECTRICAL CONTRACTOR
SHALL ATTACH FLEX CONDUIT MATERIALS SHALL BE HOT
WITH APPROVED STRAP OR DIPPED GALVANIZED INSIDE
z 3/4" MINIMUM CONDUIT
AND OUT. FURNISH HANDHOLE
< HANGER.
AND ALL MOUNTING HARDWARE.
z A . AST OUTLET BOX WITH HUB COVER AND
GASKET. SURFACE OR FLUSH MOUNT <C
AS REQUIRED
B HANDHOLE WITH FRAME AND
COVER GROUNDING NUT OR
55 ELECTRICAL CONTRACTOR LUG WELDED TO INSIDE OF NOTE:
SHALL FURNISH AND INSTALL POLE. ACCESSIBLE FROM 1. ABOVE DOOR, MOUNT BOTTOM OF FIXTURE 6" ABOVE DOOR.
HANGERSEPARATEFROMCLG THE HANDHOLE. 2. WALL, MOUNT BOTTOM OF FIXTURE 7' 6" A.F.F.
SYSTEM HANGERS.
LAY IN LIGHT FIXTURE
FINISH GRADE 6" DIA. MIN. EMERGENCY LIGHT MOUNTING DETAIL
<
O NO SCALE
O BOLT COVER
O -
O
z l-
O
CEILING SUPPORT
WIRE
o CEILING GRID
O
NOTE: I..U
O 1. SUPPORT WIRE TO BE INSTALLED IN SUCH A MANNER THAT O
WEIGHT OF FIXTURE IS HELD INDEPENDENT OF CLG. GRID
ELECTRICAL æ
ANCHOR BASE-SEE CONTRACTOR
THEREFORE WIRES MUST BE TIGHT WITH NO SLACK. FOUNDATION DETAIL
2. FLEXIBLE CONNECTION FROM FIXTURE TO JUNCTION BOX THIS SHEET Project No.: 200-11740-10003
ó. A MUST BE MIN. 18" & MAX. 72" LONG.
Designed By: CSW/AJK
LAY-IN MOUNTED Drawn By: TAC
ED UMT EMR TYPICAL POLE MOUNTED CAMERA DETAIL Checked By: DAB
NO SCALE NO SCALE

o
L9
E-9505 O

Bar Measures 1 inch