NEMISYS N70

FRONT END LOADER LIP SYSTEM

 PROVEN ADVANTAGES
FOR THE NEW FEL Integrated HP15 hinge pin
SAFETY
N70 LIP SYSTEM ESCO’s T4
Mechanical
locking system Safely change
out worn Nemisys
After 4000+ digging hours of testing and validation the new N70 system Adapter System
allows for rapid shrouds with
for Front End Loaders provided distinct advantages for miners. in-field change-outs
with zero All new
the integrated
hot work. point shapes SecureLift™
The Nemisys Advantage ®
lifting system.
Better Tooth Retention
• Proven reliability - operating in nearly
500 machines worldwide
Streamlined profile for
• Fewer lost GET because of better material flow
positive engagement design
Improved Safety
• Safer end-of-life removal
• Less touch time due to fewer change-outs N70 also available in
Harder, Longer Lasting ESCO Premium Alloys
® weld-on adapters
• Up to 2x longer than CAT®*
• Up to 45% longer than Hensley®**
• Fewer change-outs
• Less inventory required
*Based on field trial results.
**Estimated based on hardness differential and
available wear metal

Integrated single-sided point New Nemisys shrouds Wear caps for longer lasting
lock for easier, faster removal for plate lips adapters in tough applications

BETTER TOOTH RETENTION

Positive engagement with Premature point loss
Nemisys results in fewer on competitor part
lost teeth. can occur if exterior
• Fully-protected male locking features and lock retention features
female nose wear off.

2 3
 NEMISYS N70 TOOTH ®

Estimated Interior
SYSTEM OUTPERFORMS Wear Life Weight Hardness (BHN)
492

THE COMPETITION 36% increase

in wear
life†
407

13%

550
Brinell N70AP CAT
431-0062
N70AP CAT
431-0062
N70AP CAT
431-0062
Hardness
†
Estimated based on hardness differential and avaiable
Method of measuring the hardness of a material by pressing a chromium-steel wear metal, field trial results resulted in a 2X wear life
improvement over CAT.
or tungsten-carbide ball against the smooth material surface under standard test
<425 conditions. The hardness is expressed as a Brinell Hardness Number (BHN).

CAT Advansys 431-0062

®

The ESCO® Alloy Advantage

Harder surface and interior
for fewer change-outs and
more uptime.
Lower surface
and interior
hardness can lead
Estimated Interior to accelerated wear
Wear Life Weight Hardness (BHN) and more frequent
492
change-outs.
469
45% Increase
in wear
life*

8%

N70AP XS145RP2 N70AP XS145RP2 N70AP XS145RP2

ESCO Nemisys N70AP *Based on hardness differential and available wear metal.

PRODUCTIVITY
Best-in-class ‘wear life to weight’ ratio allows you
to move more dirt with the Nemisys system. Hensley XS145RP2®

4 5
 CONFIGURATIONS Choose A Lip
10° step spade
TO MEET •• Lighter System Weight*
•• Typically Loadmaster/LeTourneau/Komatsu

ANY NEED 15° step spade

•• More aggressive profile
15°
Points, wearcaps and adapters •• Typically CAT 10°
are all interchangeable *On 234” wide and larger lip systems.

Compatible with most 4” [100mm] plate lip loader offerings

from CAT®, LeTourneau™, and Komatsu®. Contact your ESCO
representative to verify compatibility.
Choose A Corner Choose A Wearcap

Choose A Point

N70WCG Gen. Purpose N70WCS Super-duty

•• 13 kg •• 17 kg
Mechanical Weld-on Adapters •• Best balance of •• Ideal for hard
penetration, wear-life, digging, high-abrasion
•• Only cast corner •• Cast corners for hard
weight and cost environments
option available for digging, weld-on
•• Best wear-life
N70A Ultimate Wear Life N70AP Balanced N70AG General Purpose mechanical systems adapters
•• 107 kg Wear & Penetration •• 68 kg
Mechanical corner adapters require a N70LWS lower wing shroud instead of a wear cap.

•• Ideal for well-blasted, high •• 97 kg •• Best balance of penetration,

abrasion environments •• Ideal for hard digging, high weight, and cost
•• Longest wear-life for abrasion environments Choose A Shroud
less change-outs •• Best balance of penetration and wear-life Nemisys® The Next
Generation of Shrouds Toplok
•• Lighter than comparable shrouds •• A history of reliability
•• Integrated Lock •• 3.3” [83mm] thick
Choose An Adapter •• SecureLift™ enabled for safer bottom leg
end-of-life removal
•• 3.9” [99mm] thick bottom leg

N70-T416 Mechanical N70-W416 Weld-on

•• 190 kg •• 114 kg
•• Ideal for tough digging environments •• Best balance of penetration, wear-life,
•• Compatible with current T417-SV2 Adapters weight and cost
•• Allows in-field change-outs with zero hot work

6 7
 

 

    
  
  

  
    
 
  
    






  


  
 

   

escocorp.com


P3042MIN-ENG-L0318 ©2018 ESCO Corporation. All Rights Reserved.