Scribd
Upload
15 views6 pages

Delta Rectifier Setting For SCU-V1.0

The document outlines the configuration process for a Delta rectifier and SCU, including steps for connecting to the devices, setting IP addresses, and logging into web portals. It details the procedures for checking software versions, importing configuration files, and adjusting networking settings. All information is proprietary to ZTE Corporation and is not to be shared externally.

Uploaded by

tungguliswardana56
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
15 views6 pages

Delta Rectifier Setting For SCU-V1.0

The document outlines the configuration process for a Delta rectifier and SCU, including steps for connecting to the devices, setting IP addresses, and logging into web portals. It details the procedures for checking software versions, importing configuration files, and adjusting networking settings. All information is proprietary to ZTE Corporation and is not to be shared externally.

Uploaded by

tungguliswardana56
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

内 部 使 用 ▲

Delta rectifier site configuration for SCU

1、Set configuration for Eaton rectifier


1.1 Connect Delta with you laptop
1.2 Find the IP of DELTA in “settings”, change IP as 192.168.4.1/255.255.255.0/192.168.4.10

1.3 change the laptop IP as 192.168.4.7/255.255.255.0/192.168.4.10, log in 192.168.4.1, account:


Admin, password: adminTps. change parameters as follows:

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第1页
内 部 使 用 ▲

2、SCU Parameter Setting

2.1 Log In to the Web Portal of the SCU


2.1.1 Use a network cable to directly connect to any network interface.
2.1.2 Setting you laptop ip4 address:192.168.1.3/255.255.255.0/192.168.1.1
2.1.3 Enter the URL (IP address: 192.168.1.2) in the address bar of a browser. The login page is
displayed, see the following figure.
2.1.4 Enter the Account, Password and Verification code. Account: admin Password:Power123 (if can
not, try admin@zteDC)
2.1.5 Click Confirm. The home page of the Web portal is displayed.

2.2 SCU upgrade


2.2.1 check the software version, if it is V1.01.08.00. Skip to 2.3 Importing the Configuration
File. If not (V2.0XXXX), need to upgrade.

2.3 Importing the Configuration File

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第2页
内 部 使 用 ▲

2.3.1.Select Maintain > Sys Management. The Sys Management tab is displayed.
2.3.2.Click the upload icon in the South Configure Import row, select the southbound configuration
file (like Huawei, Eaton, Emerson, etc), and click Open.

2.3.3. After south configure import success, click select Maintenance > edit(behind Eaton) to check
the parameters of Eaton.

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第3页
内 部 使 用 ▲

1
Wire Trans...
1
4

2.3.4. After set, restart service to take effect is displayed, click Restart Server. And check if the color of
SC200 is green.

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第4页
内 部 使 用 ▲

2.4 Networking mode/Setting vlan and IP


2.4.1. Set Wireless networking mode to Wired, select HDLC > Wireless Connection > Wired.
Then set up.
2.4.2. Set SCU IP (IP, Mask, Gateway), select Settings > Configuration Info.

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第5页
内 部 使 用 ▲

<以上所有信息均为中兴通讯股份有限公司所有，不得外传> 第6页

You might also like