1.

Samsung LE32A456CD

Symptom or defect of the TV

The TV does nothing, it doesn't turn on at all.

Solution in Samsung - LE32A456CD

In the power supply, no swollen capacitor is observed, yet they are desoldered and
they observe that the bottom part is burst. All are replaced and the TV is left
functioning.

[Link] 37PFL9604H/12

Symptom or defect of the TV

When turned on, the image appears and after a few seconds it stays without backlighting with sound.
Solution in PHILIPS - 37PFL9604H/12
Change the 2 capacitors of the inverter from 33pf/6kv to 47pf/6kv

1
[Link] 933HD

Symptom or defect of the TV

It does not turn on

Solution in SAMSUNG - 933HD

The fault is in the power supply, we have the diode D203 shorted, it is replaced, and
to function..

4. Samsung PS50C450B1W

Symptom or defect of the TV

The LED lights up red and when you try to turn it on, you hear a relay but it doesn't turn on.

Solution in Samsung - PS50C450B1W

The voltages Vs and Va of the source are measured but are not present at any time. They are replaced.
capacitors in the power supply but the problem persists. In the end, I decide to replace the entire power supply with ref.
BN44-00660B and the problem is solved. The TV works perfectly.

2
5. Fault resolved in Panasonic TX-L32E30E
Symptom or defect of the TV
Comment
The television starts perfectly and when it wants to, it darkens the right part of the screen.
The LED in red is blinking, it does not respond to the remote control, it unplugs and then reconnects.
connect and it works or it turns off again.

Solution in Panasonic - TX-L32E30E

I realize that by hitting the metallic part of the panel it turns off faster, I disassemble the panel.
And I reached the LEDs, one of the connectors has a bad solder joint, I solder it and it's working.
perfectly.

Fault resolved in LG 37LF75

Symptom or defect of the TV

You turn it on and it has sound but no image appears, without backlighting.

Solution in LG - 37LF75
The cover is removed and the filtering capacitors with a value of 680uF of the 24V from the inverter are observed.
burned out. They are replaced, but the wires carrying the 24V are burned. They are replaced.
cables that go to the inverter and at the same time the capacitors of the 680uF inverter are observed
también están inflados. Se sustituyen estos dos y el TV funciona perfectamente.

3
7. Fault resolved in LG 32LC56

Symptom or defect of the TV

The TV turns on without problems, but after about 10 minutes it starts displaying on the screen.
vertical interferences that occupy the entire screen and a kind of barcode in the
bottom

Solution in LG - 32LC56
After applying cold to the Mainboard, I observe that the image becomes clear, eventually discovering
that the problem was in the regulator IC902, it is 2.5V 1Amp., I put a regulator
AMS1117 and the breakdown is over, and there have been three.

8. Malfunction resolved in Samsung LE26A457C1D

Symptom or defect of the TV
It doesn't turn on, it doesn't do anything, the LED doesn't light up.

Solution in Samsung - LE26A457C1D

In the power supply, voltages are measured but none exist. They are replaced with the
primary capacitors of the power supply and there are already voltages in the secondary.

4
9. Fault resolved in LG 32LG3000

Symptom or defect of the TV

Sometimes it turns on and other times it doesn't.

Solution in LG - 32LG3000
The problem is with the power supply. I replaced the capacitors but it still continues.
failing. Then I replaced the four opto-isolators but it keeps failing. I have checked the
welds but I haven't found anything. In the end, I decided to replace the EAY40504401 power supply.
It is complete and the problem has been solved.

10. Fault resolved in LG 37LV5500

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything, not even the power LED lights up.

Solution in LG - 37LV5500
The power supply is checked and it is observed that one of the fuses (the 220V input one) is open.
replace and there is also a blown capacitor C603, the value is not known because it exploded
through the air. A new 330pF capacitor is installed at 2000V and the TV works perfectly.

5
[Link] resolved in DMTECH DM19XTW-H2

Symptom or defect of the TV

It has no sound, everything else works correctly.

Solution in DMTECH - DM19XTW-H2

All the capacitors surrounding the sound integrated circuit are replaced and the
TV fixed and with sound.

12. Fault resolved in Hannspree HSG1142

Symptom or defect of the TV: Does not turn on, does nothing.

Solution in Hannspree - HSG1142

The open network fuse and the TNY277 in position IC105 are completely blown.
This integrated circuit is replaced but it still doesn't work. The 18V zener ZD907 and the TV are changed.
It works correctly.

6
13. Breakdown resolved in LG [Link]

Symptom or defect of the TV

The colors look bad.

Solution in LG - [Link]
Replace integrated circuit AS15-G on the T-CON board and it's solved

[Link] resolved in HAIER LT32K1

Symptom or defect of the TV

It doesn't change with the remote, but the LED blinks when you press any button.

Solution in HAIER - LT32K1

The problem is with the remote frequency configuration. To solve it, hold down the
Press the Menu key for 10 seconds and the problem will be solved.

7
15. Fault fixed in Toshiba 32W1334G

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in Toshiba - 32W1334G

In the power supply, I find a short circuit in a group of four diodes.
parallel. Lifting one by one I locate the D118 which causes the short circuit. I replace it with
a SB5100 and the TV works correctly.

16. Breakdown resolved in Samsung UE42F5700AW

Symptom or defect of the TV

It can be heard but not seen.

Solution in Samsung - UE42F5700AW

When turned on, it lights up for a moment. The source and output of the LEDs are checked, and everything seems to be in order.
Good. The LED panel is disassembled and it is observed that in one of the LED strips there is an LED diode.
completely burned out. Since I can't find anything similar, I make a bridge and the TV works.
perfectly, with the observation that a small shadow is noticed in the area where it
I found the LED burnt out.

8
17. Breakdown resolved in LG M2362D

Symptom or defect of the TV

It doesn't work, it does nothing.
Solution in LG - M2362D
The power supply is checked and it is observed that there are no swollen capacitors. There is a lot of consumption.
when it connects to the mainboard. It is measured on the mainboard, in the area of the converters
DC/DC and I see that the capacitor C1107 in SMD format next to the connector that
The power supply is short. It is replaced with a 100K one and the TV is repaired.

[Link] resolved in Philips MWT231T

Symptom or defect of the TV

It darkens a few seconds after turning it on.

Solution in Philips - MWT231T

The power supply / inverter with ref. 715G2783-3-7 is tested and the problem persists due to
I believe that some of the CCFL lamps have low emission and activate it.
inverter protection. To deactivate the protection, we go to the control integrated circuit OZ9938 and
We take the fuse 3 to the mass. Now the lamps no longer turn off. We have several working.
hours and the TV works perfectly without overheating or failing.
9
[Link] resolved in JVC LT-26DA8ZU

Symptom or defect of the TV

When you turn it on, the screen lights up for a moment and then goes dark, the sound remains.
Solution in JVC - LT-26DA8ZU
It is observed that in the inverter there is a transformer that measures differently from the others, it is replaced with
ref. 4001Y but it continues to have the same defect. It is decided to remove the protection from the integrated.
OZ964 placing a LED between pin 6 and 10 and then the TV works correctly, I don't know
no transformer overheats, so everything is supposed to be fine. It is tested.
for a week without having any problems.

20. Fault resolved in Grundig 37LXW94-7731

Symptom or defect of the TV

It turns on with sound but does not light up the screen.

Solution in Grundig - 37LXW94-7731

I check the inverter and observe that there is no power. I see in the power supply the connector of
power supply to the burnt inverter. All the wiring is cleaned and the TV works perfectly.

10
Fault resolved in PHILIPS 40PFL6606H/12
Symptom or defect of the TV
It does not turn on anything

Solution in PHILIPS - 40PFL6606H/12

The initial fault was that there was no signal coming through the Euroconnector, the main board was changed for not
to know the value of the components that were blown and when placing the new one this appeared
breakdown, the defective plate was coming. The original was 313929715231 and they sent 313929714851,
but this one is also valid.

22. Fault resolved in Samsung LE32A336J1D

Symptom or defect of the TV

It does not turn on, the LED blinks 3 or 4 times and stays in standby.

Solution in Samsung - LE32A336J1D

We examined the outputs and there is only the standby, so we suspect the primary. RM801 of 0.22
Open ohms.

11
23. Breakdown resolved in Sony KE-P42M1

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in Sony - KE-P42M1

In the power supply I check that when I heat the TV with a heat gun
it works. I change capacitors but it stays the same. In the end, I realize that by heating the
MCZ3001 integrated circuit, the TV works fine. This MCZ3001 is replaced and the TV remains
repaired.

24. Malfunction resolved in PHILIPS 32PFL5604H

Symptom or defect of the TV
It turns on well, and after 2 or 4 hours, the screen goes black with sound.

Solution in PHILIPS - 32PFL5604H

This LCD has an inverter power supply; at the output of the inverter, in my case, there were 2 capacitors of 220 pk.
2kv are blackened and cracked, I replaced them with 2 of 330pk 2kv, and ok, (note) review.
weldings, in all conditions, and hollow weldings.

25. Breakdown solved in Schneider Micra 3225

12
 Symptom or defect of the TV
Sometimes it doesn't even turn on the pilot, other times it turns on and works well.

Solution in Schneider - Micra 3225

In the power supply, the integrated circuit D301, which is a TL431 in SMD format, is faulty.
it was replaced and the TV works perfectly during 4 days of testing.

26. Fault resolved in Samsung PS-42C96HD

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything, not even the LED lights up.

Solution in Samsung - PS-42C96HD

The power supply is checked and it is observed that it does not provide standby voltage. This standby power supply
It is controlled by the Viper22 circuit with position ICBSC1S, it is replaced but it still does not work.
tension. The ZDB803 protection diode is removed and the power supply is already providing voltages, then

13
 I place a 22V zener since the voltage present in this zener is 19V and it is used for
feed the Viper22.

27. Fault resolved in Airis MW141

Symptom or defect of the TV

It doesn't turn on, it does nothing.

Solution in Airis - MW141

This type of device often has failing capacitors in the power supply, especially in the
secondary ones are blown and it doesn't start, replace them and the device is working.

28. Breakdown fixed in Samsung LE40B541p7w

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution on Samsung - LE40B541p7w

In the power supply, it is observed that the main switching transistor QP802 is
find in short. It is decided to replace the complete power/inverter and the TV works perfectly.

14
[Link] resolved in LG 37LC2RR
Symptom or defect of the TV
It takes more than 20 minutes to see and hear it, although the screen lights up and the menu appears, the
program and the volume bar.

Solution in LG - 37LC2RR
The +6V from the power supply to the main board is measured and in cold conditions it only has 1.5V, and it is gradually increasing.

C234 of 1000microfarads/25V is replaced in the power supply and the problem is solved.

30. Fault resolved in JVC LT-32DH8ZG

Symptom or defect of the TV

The remote control doesn't change.

Solution in JVC - LT-32DH8ZG

The infrared receiver is checked and replaced for testing, but the TV still does not receive commands.
of the control. Some capacitor is observed swollen from the bottom in the power supply. It
All the capacitors are replaced and the TV is now working well with the remote control.

15
31. Fault resolved in SONY KDL-40S2000

Symptom or defect of the TV

There is no video, black screen. The back light, tuner, and audio are OK.

Solution in SONY - KDL-40S2000

The first thing I check is that the Main Board sends the 5 volts of power to the T-CON. In the T-
I measure the same 5 volts but only at one end of the fuse, indicating that it is open.
I unplug the TV, and I measure the fuse in ohms to check that it is open. The fuse is
SMS-type miniatura with a letter "P". I adapt a 3 Ampere fuse a little larger.
extracted from another T-Con and the TV is repaired. I test it for 24 continuous hours before
deliver it to the client.

16
[Link] resolved in LG 32LG3000-ZA

Symptom or defect of the TV

It doesn't turn on. The LED blinks red 3 times and then goes into stand-by.

Solution in LG - 32LG3000-ZA
The capacitors of the FDA, C251-C253-C252 and C203 (marked in blue in the
photos). Only one of them is swollen, but all are changed for prophylaxis. They are from
1000mF at 35v; replaced with 1000mF at 50v, and it works.

33. Breakdown solved in Sony KLV-30HR3

Symptom or defect of the TV

It doesn't turn on, the LED blinks.

17
 Solution in Sony - KLV-30HR3
It is measured at the source and it is observed that the standby voltage is low and fluctuating. It is replaced the
integrated standby source control with reference STR A6169 and the capacitors but the TV
it keeps failing. In the end, I realize that diode D6102 is short-circuited, I replace it with a
1N4007 and the TV works perfectly.

34. Issue resolved in LG 42LG2000-ZA

Symptom or defect of the TV

Correct sound with a white screen. Correct backlighting. It gradually turns on a
a white blurred square in the center of the screen gradually lights up completely in white.
Solution for LG - 42LG2000-ZA
The malfunction comes from the T-CON board or control board. The 2 inverters are working. They are measured.
Voltages at the F1 input (13v) and at the output are present. The board is replaced.
Enter, T370XW02 VC, very difficult to find and very expensive!!!, and to work.

18
Fault resolved in Samsung UE22ES5000

Symptom or defect of the TV

The TV works but every now and then it turns off.

Solution in Samsung - UE22ES5000

The source is checked and it is observed that tapping on it causes the TV to turn off. The ...
welds and it can be seen that in the control integrated circuit of the supply there are several pins almost loose. It
completely resolve the integrated circuit and the TV will not fail again.

Breakdown fixed in Samsung LE32S73BD

Symptom or defect of the TV
The LED blinks constantly.

Solution in Samsung - LE32S73BD

I measure tensions in the source and the 12V oscillates between 3.6V and 1.8V, I change the filters and it remains the same.
I changed the F9222L integrated circuit and it's fixed. I also changed the disabled cm813 and cs802.

Fault resolved in Samsung LE2R86BD

Symptom or defect of the TV
It doesn't work, the standby LED lights up but it doesn't do anything.

Solution in Samsung - LE2R86BD

It is observed in the source that several capacitors in the secondary are a bit swollen.
they all replaced with satisfactory results since the TV turns on perfectly.

19
38. Fault resolved in SAMSUNG LE19R86BD
Symptom or defect of the TV
Red LED blinks 5 times, turns off, and blue LED turns on, gives a small flash, but nothing appears.
image or sound.

Solution in SAMSUNG - LE19R86BD

C315 of 820mic, C111 of 820mic, F301 fuse of 3Amp, all in the secondary of the power supply.
The capacitors appear swollen, and the fuse is cut.

39. Fault resolved in Samsung LE40A550

Symptom or defect of the TV
The image looks bad, as if it were solarized.

Solution in Samsung - LE40A550

I proceed to change the AS15F chip, but when I turn it on, the new one completely burns out.
I need to change the T-CON board V400H1-C03. Once the new one is installed
the TV works correctly.

[Link] resolved in LG LG32LG3000

Symptom or defect of the TV

It turns on, with no audio, dark screen and has backlighting, after 20 minutes it starts working.

Solution in LG - LG32LG3000
2 capacitors 3300uF16V from the secondary of the power supply EAY40504401

20
Fault resolved in Sony KDL40U2000
Symptom or defect of the TV
When connecting, it turns off instantly. The red light blinks in intervals of four, it doesn't reach
illuminate the screen.

Solution for Sony - KDL40U2000

The source voltages are checked and are correct. It is checked that the inverter does not reach
remove, change fuse f3 of 0.5a on the inverter board next to the input connector, and the TV starts.

[Link] resolved in SHARP LC40LE810E

Symptom or defect of the TV

It would turn off when heated up. It would disconnect from the network and work again, but for a shorter time.

Solution in SHARP - LC40LE810E

The source heated up in areas, resulting in the area of 3 couplers that were together,
reacted to temperature changes. SMD components were resoldered in that area, with no results,
I replaced the three optos (PC7703-PC7901-PC7702) and it was fixed, the one that was failing was one of them.
but I changed the three, just in case.

21
[Link] resolved in Samsung LE37A558P3F

Symptom or defect of the TV

The solarized image is seen, with the colors changed.

Solution in Samsung - LE37A558P3F

The T-CON is checked and it is observed that it has the AS15F integrated circuit, which is replaced with a new one.
taking great care when soldering it and the TV is repaired, it looks perfect.

22
44. Fault resolved in Philips 32PF5531D

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in Philips - 32PF5531D

The power supply is checked and it is observed that there are no output voltages.
check that the diode D600 is shorted. It is replaced by an SB5100 and the TV turns on
perfectly.

23
45. Malfunction resolved in Sony KLV-21SG2

Symptom or defect of the TV

Sometimes it struggles to turn on and the red light starts blinking instead of the green one turning on.

Solution in Sony - KLV-21SG2

The source voltages are checked and nothing unusual is observed. I decide to replace the capacitors.
from the power supply, several of them in SMD format and the TV works correctly without
fail.

46. Fault resolved in SONY KDL-22BX20D

Symptom or defect of the TV

Image without backlighting
Solution in SONY - KDL-22BX20D
After checking that the lamps are correct, I measure the inverter transformer and the two outputs.
It measures the same, I decided to replace it and it works perfectly. Transformer in bad condition.

24
Fault resolved in Philips 42PFL5522D

Symptoms or defects of the TV

The pilot light turns blue and then changes to red, but it does not turn on.

Solution in Philips - 42PFL5522D

The source is checked and several 2200uF and 1500uF capacitors are observed to be swollen.
they are replaced but the TV keeps failing. It is measured with the multimeter and I see that the 12V are missing. It
replace the C520 of 10uF that is dry and the TV works perfectly.

Fault resolved in LG RZ-27LZ55

Symptom or defect of the TV
Nothing turns on, the LED is off.

25
 Solution in LG - RZ-27LZ55
The power supply is checked and capacitors are replaced but the TV remains faulty. It is decided to replace the
integrated standby source control with ref. F9222 and the TV works perfectly.

49. Fault resolved in SHARP LC-22LE510E

Symptom or defect of the TV

It doesn't turn on anything

Solution in SHARP - LC-22LE510E

the power supply is checked and we find the D708 shorted on the +24v line, we
change the diode and it will work ...

26
Breakdown resolved in SAMSUNG
PS42A416C1DXXC

Symptom or defect of the TV

No image with sound. Power supply output tensions are correct.
Solution in SAMSUNG - PS42A416C1DXXC
Replace Diode UF4007 position D5014 (short-circuited). Resolder transformer T5000.

Fault resolved in LG 42LG3000

Symptom or defect of the TV

It does not tune channels, after performing an automatic search it still does not tune.

Solution in LG - 42LG3000
The antenna connection is checked and the signal is found to be good. It is decided to replace the
tuner with ref. TDFV-G135D. Once replaced, a new channel search is performed and the
TV tunes into everyone.

27
Fault resolved in SONY KDL-40HX750
Symptom or defect of the TV
It turns on and off several times until the red light flashes intermittently, 8 flashes.
Solution for SONY - KDL-40HX750
Software error, perform a reset and it's solved.

[Link] resolved in LG 42LC2D

Symptom or defect of the TV

It doesn't work, the LED lights up red but does nothing.

Solution in LG - 42LC2D
The back cover of the TV is removed and it is observed that there are several in the power supply.
Swollen capacitors. All are replaced and the TV is repaired.

Breakdown solved in Samsung

LS17PEASW/XAX

28
Symptom or defect of the TV
The CCFL lamps turn off 2 seconds after being turned on. I am disconnecting them one by one.
lamps and connect a test lamp until all are lit to know which one is the
that is damaged.

Solution in Samsung - LS17PEASW/XAX

The CCFL lamp is very difficult to obtain, so I replace it with a ceramic capacitor.
100pF 3KV soldered on the board. The equipment works perfectly with only 3 out of 4.
lamps.

Fault resolved in Samsung LE23R86BD

29
Symptom or defect of the TV
It doesn't turn on, it doesn't do anything, the indicator is always off. There is no +5V standby.

Solution in Samsung - LE23R86BD

The source is checked and it is verified that the fuse is good and we have 300V at the line filter.
Reviewing the 5V source that is controlled by the IC8801S position integrated circuit, I check that there is
a short in the power supply that reaches it rectified by the diode D8802. The leg of the
integrated and the diode D8802 but the short circuit is still present. The zener diode DZ8803 is raised in format
double smd and the short disappears. Therefore, we replace this diode with an 18V zener in format
normal and the TV works perfectly.

30
 Breakdown fixed in LG 32LK330-DB

Symptom or defect of the TV

Television turns on the pilot LED when connected, does not respond to Power command and turns off.

Solution in LG - 32LK330-DB
Voltages are taken from the power supply and the standby voltage is found, the Power command is given and the voltages appear.
except for the INV_ON order which is 3.3V. This voltage is checked at the collector of Q405 in the

31
Mainboard is missing, but the inverter's power order is found in the base. It is done.
Following the trail, a L424 coil with a false contact is found.

[Link] solved in HITACHI 32LD6200

Symptom or defect of the TV

Turn on the standby light but without backlighting.

Solution in HITACHI - 32LD6200

Power supply Malfunction Replacement C16 disabled Set Value 47mf/50V Fault fixed

58. Issue resolved in Samsung LN32D450G1D

Symptom or defect of the TV
There is no image, but sound OK, backlight OK, LVDS signals OK. I'm going to check the card that is.
stuck to the panel and I find an SMD fuse in green that has an open "K".

32
Solution in Samsung - LN32D450G1D
I replace the fuse with a 2A one, the image returns. After testing it for 24 continuous hours, the
return to the customer.

59. Issue resolved in Sony KDL-37V4500

33
Symptom or defect of the TV
The image appears solarized, very poor quality.

Solution in Sony - KDL-37V4500

Comment
0 MAN_REPAR
The T-CON is checked and it is observed that it has an integrated AS-15U. It is replaced with an AS-15F and the TV
It is repaired and functioning perfectly.

[Link] resolved in LG 42LG5000

34
Symptom or defect of the TV
It doesn't turn on, it doesn't do anything. No light comes on, as if there is no power.

Solution in LG - 42LG5000
The power supply is checked and it is confirmed that the two glass fuses it has are
open. After checking some more components I see that the transistors Q111 and Q110 are in
short and blown. The switching control integrated circuit of these transistors is soldered.
The part of the tracks is also destroyed, so I decide to replace the entire source with ref.
EAY40505201

61. Fault resolved in LG 32LD350

Symptom or defect of the TV

It turns on and you can hear it but there is no picture.

Solution in LG - 32LD350
The problem is located in the inverter. The inverter board is checked and I notice a 2A SMD fuse.
marked as F1 open. I replace it with a 2A type TR5 and the TV works perfectly.

35
 62. Malfunction fixed in LG 42LC55

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in LG - 42LC55
The Q201 is replaced by a BC818 and the TV works fine.

Fault resolved in SAMSUNG LE32C530F1W

Symptom or defect of the TV
The image looks double, like it's repeated twice.

Solution in SAMSUNG - LE32C530F1W

I solved it by removing one sheet from the two that the T-Con card has, upon seeing that half of the screen
The flaw was fixed. With a piece of tape about two millimeters wide, I covered it four at a time.
four clues, and until I found the wrong trace, and the image was corrected. If it weren't so, do the same with
the other sheet and the issue solved.

36
 64. Fault resolved in LG 32LH5000
Symptom or defect of the TV
The screen does not turn on, there is no backlighting.

Solution in LG - 32LH5000

The power supply voltages are checked and it is observed that all are present. It is decided
replace the inverter with ref. EE32FH-0 and the TV works perfectly.

65. Malfunction resolved in LG 32LG2000

Symptom or defect of the TV

The TV won't turn on, the light changes from red to blue but does nothing else.

37
Solution in LG - 32LG2000
It is checked that the inverter and the power supply are functioning properly, and the EEPROM is verified.
lifting it and none is placed in position IC105. Now the TV turns on and the menu appears
first installation. To completely repair the TV, an empty EEPROM is installed and the TV works.
perfectly after conducting the channel search.

[Link] resolved in Samsung LE37A557P2

Symptom or defect of the TV

The white screen is visible and it is heard perfectly.

38
Solution in Samsung - LE37A557P2
The T-Con fuse is checked and is fine. It is decided to replace the AS15F integrated circuit. Once the
new integrated the TV works correctly.

Most image problems are solved by changing the AS15F.

[Link] resolved in Philips 32PFL5604h

Symptom or defect of the TV

The image appears for a moment and then disappears.
Solution in Philips - 32PFL5604h
I review the inverter power supply and decide to change it since the PLHL-T808 has a lot of these issues.
After putting it on, the TV continues to have the same problem. I disassemble the LCD panel and observe that
there are several lamps that emit pink light and one of them doesn't even turn on. I replace the lamps with
Some that I have here that are a little shorter but work.

39
 68. Fault resolved in Sony KDL-40U2000

Symptom or defect of the TV

The screen lights up and illuminates but there is no image.

Solution in Sony - KDL-40U2000

The problem lies in the T-CON board, sometimes it needs to be replaced because it has a short circuit but in
In this case, just replacing the fuse solves the problem.

Fault resolved in Samsung LE26C450E1WXXC

Symptom or defect of the TV
It doesn't turn on. The standby light also appears to be off.

Solution in Samsung - LE26C450E1WXXC

The output voltages of the power supply are checked and all are at 0.1 and 0.3 volts. I disconnect the pin that
It powers the Main Board, and now all the voltages are present. The Backlight even turns on.
I decide to change the Main Board BN41-01331B and the TV works.

40
 70. Fault fixed in Toshiba 22EL833G
Symptom or defect of the TV
It won't turn on. The standby light also appears to be off.

Solution in Toshiba - 22EL833G

Replace the SB5B0 diode that is shorted. Position of the diode D709. (The TV remains
functioning)

Fault fixed in Sony KDL26EX302

Symptom or defect of the TV
When turning it on, the image appears with stripes; sometimes it darkens or freezes, but sometimes moving it makes it visible.
then he/she leaves.

Solution in Sony - KDL26EX302

I notice that when I move the first cable to the left of the tcon that goes to the panel, it works correctly.
I leave the subject in a position and it works correctly.

Fault resolved in LG 26LB75

Symptom or defect of the TV

No image. With sound.

Solution in LG - 26LB75
Fused F1 open on inverter board. It is near connector CN1, and it is a black micro fuse.

41
 Fault resolved on Philips 37PFL3512D
Symptom or defect of the TV
It doesn't turn on, not even the LED light.

Solution in Philips - 37PFL3512D

Measurements are taken at the source and where the 5V standby should be, there is nothing. The check is performed.
The primary and the switching transistor are fine. The control circuit is tested to be changed with ref.
NCP1207A mounted in position IC901 and the TV turns on perfectly.

42
 72. Malfunction resolved in Sanyo CE32LD81-C

Symptom or defect of the TV

The TV works well but the digital terrestrial television constantly pixelates.

Solution in Sanyo - CE32LD81-C

The TDT module is reviewed and a capacitor at position C505 is found to be swollen, it is replaced and the
TV works perfectly.

73. Fault resolved in PHILIPS 42PFL5604H

Symptom or defect of the TV

The screen randomly turns off, sound is fine. No brightness with volume.

Solution in PHILIPS - 42PFL5604H

This model has a combined power supply and inverter module. But the design takes advantage of the
mounting holes on the chassis to connect the grounds. We have verified that the screws come
loose and the solder at the bottom of the contact oxidizes, producing false contacts. Installed
some cables between the mass tracks and the fastening screws with terminals were resolved.
43
 74. Malfunction fixed on Toshiba 37RV733

Symptom or defect of the TV

The red light comes on, turns green, and doesn't turn on, it does nothing.
Solution in Toshiba - 37RV733
The power supply is checked and works correctly, the inverter is tricked into working and
the screen is also lit, so the inverter is working well. The mainboard PE0828 is replaced as it is the
what produces the failure and the TV works perfectly.

[Link] resolved in Samsung LE40R73BD

Symptom or defect of the TV
You turn it on and it has an image, but after a while it disappears.

Solution in Samsung - LE40R73BD

The power supply and inverter are checked, and some cold solder joints are observed.
inverter transformer. It is completely resoldered and the TV does not fail again.

44
 76. Fault resolved in Philips 26PF4310

Symptom or defect of the TV It doesn't turn on, no image and no sound

Solution in Philips - 26PF4310
Replace the electrolytic capacitors marked in the photo.

Fault resolved in PHILIPS 22PFL3805H

Symptom or defect of the TV

It turns on and the screen does not have LED backlighting, checking the power supply I notice that the 24v is
they come down
Solution in PHILIPS - 22PFL3805H
Disassemble the display panel and remove the capacitor that goes to 24v, the C415. I have removed all 3 as a precaution.

78. Fault resolved in Toshiba 32AV733G

Symptom or defect of the TV It does not turn on, it does nothing.

45
Solution in Toshiba - 32AV733G
In the main power supply, we find that the transistor Q971 is shorted between Base and emitter,
The Q970 is fine. The Q971 is replaced by a P7NA60 and the power supply control integrated circuit is also replaced.
with reference L6599A in SMD format and the TV works perfectly.

Fault resolved in Samsung UE37C6000

Symptom or defect of the TV

It changes channels by itself and adjusts the volume up and down, it doesn't allow changing with the remote, only sometimes.

Solution in Samsung - UE37C6000

The problem is with the touch button panel that is not functioning correctly. It is replaced with ref. BN96-13047C and the
TV works correctly.

80. Malfunction resolved in SAMSUNG LE32S67BD

46
Symptom or defect of the TV
It turns on but after about 5 minutes it completely turns off, leaving the standby indicator in red.
Solution in SAMSUNG - LE32S67BD
The malfunction is resolved by changing the capacitors in the power supply as indicated in the photo.

[Link] resolved in LG 37LC2D-SC

Symptom or defect of the TV

Takes a long time to turn on
Solution in LG - 37LC2D-SC
Faulty capacitors of the power supply capacitors c201 and c202 of 3300uf 10v. They are replaced and
it works correctly.

82. Breakdown solved in Hitachi L37V01E

Symptom or defect of the TV It turns on but there is no image.

47
Solution in Hitachi - L37V01E
The inverter is checked and one of the transformers is found with the secondary open. This one is replaced.
transformer with reference 6024B and the TV works perfectly.

83. Malfunction resolved in Samsung UE32C6510

Symptom or defect of the TV

It has sporadic failures, the image goes away, comes back, and turns off and on.
Solution in Samsung - UE32C6510
The problem lies in the soldering of the microprocessor on the mainboard. It can be attempted.
to do a reballing but I have opted to change the mainboard.

48
 Fault resolved in LG 32LB75
Symptom or defect of the TV It doesn't turn on, it does nothing.

Solution in LG - 32LB75
The rear cover is removed and I observe some swollen capacitors in the power supply, all the ones in the power supply are replaced.
as a precaution and the TV works perfectly.

85. Repair solved on Samsung LE37S73BD

Symptom or defect of the TV It doesn't turn on, it doesn't do anything, the light stays red.

Solution in Samsung - LE37S73BD

In the power supply, several faulty capacitors are seen and all are replaced as a precaution. The TV remains
repaired.

49
 86. Breakdown solved in JVC LT-37DR7BU
Symptom or defect of the TV
It turns on but does not light up the screen, it only lights up for a few seconds and then disappears.

Solution in JVC - LT-37DR7BU

The inverter is checked and I verify that one of the transformers 6010B is open. It is replaced with a new one.
and the TV is repaired.

87. Breakdown resolved in LG 32LF2510

Symptom or defect of the TV The pilot light is on but does nothing else.

Solution in LG - 32LF2510
It is observed that the pilot changes state when you turn it on, but the source only supplies 3.3V.
the other tensions do not appear. The problem lies in the main source that is not functioning. After
I investigate for a while and see that the 15V ZD503 Zener diode is leaking. I replace it and it works.

50
 Breakdown solved in LG 32LH2000
Symptom or defect of the TV The image flickers constantly.

Solution in LG - 32LH2000
The inverter is checked and appears to be fine. The display is disassembled and it is observed that one of the lamps has a
false contact, it is properly filed and directly soldered to its support so that it does not fail again.

[Link] resolved in LG 42PJ350

Symptom or defect of the TV No Image

51
Solution in LG - 42PJ350 Breakdown I was in Ysus. Had Tranf. T501 open.

[Link] resolved in SAMSUNG PS42E97HD

Symptom or defect of the TV

It does not turn on, the standby LED blinks with relay noise.
Solution in SAMSUNG - PS42E97HD
Power supply faulty, there is a KIT for this power supply, the components of the kit are highlighted in red for
replace and the TV is repaired.

91. Issue resolved in LG 32LB75

Symptom or defect of the TV It doesn't turn on, it does nothing, only the LED lights up.

52
Solution on LG - 32LB75
In the power supply, some 2200uF capacitors are replaced and the TV works perfectly.

92. Fault resolved in LG 37LG2000

Symptom or defect of the TV
Soon the MENU starts to appear, it disappears, it appears, everything is just uncontrolled, blue light blinks, and even being
turned off turns on by itself.
Solution in LG - 37LG2000
Change the P/M button on the IR receiver board.

Fault resolved in Philips 26PF5521

Symptom or defect of the TV Nothing turns on, not even the standby light.
Solution in Philips - 26PF5521
Faulty power supply. Replace electrolytic capacitors C130 and C236.
53
 [Link] resolved in SAMSUNG LE26S86BD
Symptom or defect of the TV
It turns on with a white screen and noise in the speakers. When heating, the noise stops but the image remains white.
Solution in SAMSUNG - LE26S86BD
The problem with the image is the t-con. It is replaced and looks perfect. The noise from the sound is due to two.
1000uF/10V capacitors that are next to the microprocessor, under a protective cover.
refrigerates. They are replaced and the TV is repaired. These capacitors measure okay, but they need to be replaced.

Fault resolved in LG 32LG4000

Symptom or defect of the TV: Does not turn on.
Solution in LG - 32LG4000
The TV does not start. The front LED flashes twice. The 24512 EEPROM is removed and it powers on. A virgin one is installed and
The TV works perfectly. The panel type needs to be adjusted in the service menu.

96. Issue resolved in Samsung LE37A65A1F

Symptom or defect of the TV
The television has a lot of brightness when turned on, the screen is almost white... other than that, it works perfectly.
Solution in Samsung - LE37A65A1F
This is the typical failure of the T-CON with the AS15G chip, I replace it and the television works perfectly.
I have uploaded because the model was not listed here with this error.

97. Malfunction resolved in Samsung LE32d400e1wxxc

Symptom or defect of the TV
It lights up but doesn't backlight... the sound is fine.
Solution in Samsung - LE32d400e1wxxc
We checked the inverter and it seems correct...it doesn't have a fuse...the voltages in the power supply are OK....except for the one that
suministra tensión al inverter....localizo un transistor abierto SMD, lo sustituyo pero sigue igual...al final sustituyo
the source is fixed...I also update the firmware :)

54
 Fault resolved in LG Flatron W1934S-BNT

Symptom or defect of the TV

the monitor is unable to turn on or light up the panel, the LED blinks constantly as if there is some
short in the power supply
Solution in LG - Flatron W1934S-BNT
The power supply is checked and it is confirmed that the 100uF and 400V input capacitor is leaking a little acid.
one of its sideburns is replaced and it continues to cause the problem, the components are checked and measured and the issue is located
Capacitor C923 of 1000uF and 16V in bad condition, replaced and the monitor is repaired.

99. Fault fixed on Philips 42PF5532D

Symptom or defect of the TV

The screen does not light up, it only makes low-intensity white flashes that disappear quickly.
like a hiccup.

Solution in Philips - 42PF5532D

Voltages are measured at the output of the Y-Sus and I notice that the voltages vary according to the flash. I decide
replace the Y-SUS board LJ41-05134 and the TV works correctly.

55
 [Link] resolved in LG 42LW650S

Symptom or defect of the TV: It turns on and there is sound but the screen never lights up.
Solution in LG - 42LW650S
The power supply is checked and it has all the voltages. I observe that the Back light On line is
I lower it and activate it with 3V3, then the screen lighting LEDs light up. The problem is on the mainboard.
that doesn't activate this line. The mainboard EBT61401010 is replaced and the TV is repaired.

101. Breakdown resolved in LG 22LS4D

Symptom or defect of the TV When it turns on, the whole screen goes blank, it has sound.
Solution in LG - 22LS4D
It does not have a separate T-con, it is integrated into the panel, the SMD fuse F1 is open, when replacing it, it comes back.
To jump... one of the SMD capacitors next to C202 shows continuity on the board, I decide to take it out and it gives
continuity out of plate, in the end I take one from a monitor that I have broken and replace it with the one from the TV,
I put in another fuse and the TV works perfectly.

56
 102. Breakdown resolved in LG 42PQ6000
Symptom or defect of the TV
It doesn't turn on, the indicator blinks several times and then it turns red again.

Solution in LG - 42PQ6000
The fault is located in the EEPROM memory which becomes corrupted. The old memory is lifted and a new one is installed.
a blank screen, the TV starts and you just need to do an automatic tuning and that's it.

Fault resolved in PHILIPS 42PFL7404H/12

Symptom or defect of the TV
Nothing turns on, not even the LED.

Solution in PHILIPS - 42PFL7404H/12

In the power supply, the D911 is shorted, it is an sb260, schottky of 60v 2 amp, I replaced it with a diode.
1n5822, 40v 3 amp Schottky, and ok. I touch the diode and it does not heat up at all.

[Link] resolved in Panasonic TX-L32V10E

Symptom or defect of the TV
It can be heard and changes channel, but the image is not visible. It has backlighting.
Solution in Panasonic - TX-L32V10E
It is identified by the symptom that the fault may come from the T-Com board. It is checked that many of the
components of that board have no voltage, so it was decided to replace the entire board. With the new board the
TV is working correctly.

57
 105. Issue resolved in Samsung LE37M87BD

Symptom or defect of the TV

TV with two faults: 1st The TV takes a very long time to turn on, approximately 35 minutes. 2nd Once turned on
the image appears with stripes like in the first photo, it can also be seen with the image vibrating, and even with
strips of approximately 4 centimeters in various colors, with green being the predominant color.
Solution on Samsung - LE37M87BD
The first fault is resolved by changing the electrolytics of the secondary of the power supply, some of them were not
bad and they gave value within the established but I have healed for my own good. The second failure was caused by two
SMD capacitors of 1000 microfarads 10V that are located under the plate of the second photo, are
They can put the capacitors from the old days, but these do not fit so I have cut the sheet metal so that
stand out upwards and be able to fit the perfect plate, as it is essential to have it on because it does
of the heatsink of two ICs.

106. Breakdown resolved in LG 32LX2R

Symptom or defect of the TV
When plugged in, the standby light turns on and then immediately goes off, then it does nothing.
Solution in LG - 32LX2R
In the power supply, the secondary capacitors c221 and c222 of 1000uF 10V, which are not
They are neither swollen nor look bad, they give a high ESR, they are replaced with ones of 1000uF and 16V and the TV works.
walking perfectly.

58
 Fault resolved in Samsung LE32B350F1W

Symptom or defect of the TV

The TV won't turn on, it does nothing, only the indicator light responds when pressing any button on the remote, but it doesn't do anything.

nothing.
Solution in samsung - LE32B350F1W
The tensions of the BN44-00289B power supply oscillate, and if you disconnect the main, the backlights flicker. They are replaced.
These diodes and the TV work perfectly, ZM804, DM852, ZD804, ZD803, DM803, ZM801, and DM802.

108. Fault resolved in Toshiba 15VL54G

Symptom or defect of the TV
It lights up for one or two seconds but then the image goes away or it turns off.

Solution in Toshiba - 15VL54G

Tested with another 12V power supply and no difference is noticed. Upon opening, a swollen capacitor [C637] can be observed.
(G-LUXON 470µF/25V). It is replaced and it works now. Another one of 1000µF/16V nearby has the plastic casing shrunk.
due to the heat. It is changed preventively.

109. Fault resolved in SAMSUNG LE37A457C1DXXC

Symptom or defect of the TV
When turned on, it looks more or less fine, but soon the image darkens a bit. All the parameters and
levels are fine, even the energy savings are set automatically, since it is set in the middle
The null remains the same. Reviewed the source, nothing abnormal is noticed, in the inverter either, and the voltages.
correct.
Solution in SAMSUNG - LE37A457C1DXXC
The fault was in the T-CON BN41-01862 (37T03-C01), which, once replaced, allowed the TV to function.
correctly. This T-CON mounts the IC AS-15, and it is likely that it was the cause of the mentioned failure.

59
 110. Fault resolved in LG 32LD320-ZA
Symptom or defect of the TV
It doesn't show. An image forms on the LCD, but there's no backlight. There's also no sound because it doesn't tune in.
no channel.

Solution in LG - 32LD320-ZA
It is observed that the INV_CTL signal reads 0.84V, instead of the 5V necessary for the Inverter to activate. In the
USB port also shows the same 0.84V instead of its nominal 5V. The diagram shows that they come from
a +5V_GENERAL line that shows 0.84V. It is also observed that the Tuner is powered from this line and therefore
Its absence causes it not to tune anything. The USB connector shows the same. These 5V are generated in the IC808.
(MP2305DS, DC-DC step-down manufactured by MPS) from 12V, which are fine. Change of this IC for
another from the scrapyard and all anomalies are resolved. Problem applicable to MAIN plates with code
EAX60686904 or EBT61016702.

111. Fault resolved in SHARP LC42SB55E

Symptom or defect of the TV
The input menu appears, it doesn't stop in any function, it doesn't respond to the buttons or the MD, it needs to be turned off.
By unplugging it from the network, the client tells me that sometimes it turns on or off by itself.

Solution in SHARP - LC42SB55E

Change the power micro switch on the control panel, these micros have 5 pins, I put one with 4 pins and it works fine.

60
 112. Malfunction resolved in Hitachi 24H8L03

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Hitachi Solution - 24H8L03

The power supply is checked and it is observed that there is a short circuit in one output. The diodes are measured.
that output and there is one of them in short. They are replaced by an SB5100 and the TV works well.

113. Breakdown solved in LG 42LW650S-ZC

Symptom or defect of the TV
You turn it on but the screen doesn't light up and it doesn't do anything.

Solution in LG - 42LW650S-ZC
The source is checked and it is observed that it has the voltages because the Power_on line is active. However, there is no
rear light. The Driver_on signal is activated and then the backlight LEDs light up, so it is discarded.
the power supply. What is wrong is the mainboard. It is replaced with a new one with the ref. EBT61401010 and the TV works
perfectly.

Fault resolved in JVC LT-19DA9BU

61
Symptom or defect of the TV: It turns on but there is no picture, only audio.
Solution for JVC - LT-19DA9BU
In the power supply with inverter, the output transformer of the inverter is measured and a
open circuit. The transformer with reference TMS93264CT is replaced and the TV works perfectly.

[Link] resolved in LG 42LG3000

Symptom or defect of the TV Lines appear on the screen or sometimes it turns white.
Solution in LG - 42LG3000
We suspect the panel, we move it and the fault disappears, we remove the panel and notice that one of the
The panel's flex connections are not making good contact, we put a piece of rubber to apply pressure and it works.
perfectly.

116. Fault resolved in Sony KDL32P3000

Symptom or defect of the TV Only the sound is heard and the screen is black.
Solution in Sony - KDL32P3000
It is measured at the T-CON if it has 5v and it is detected that there is a blown SMD fuse at the input.
it replaces and works perfectly

Malfunction resolved in 42LC55 LG

62
Symptom or defect of the TV
Good morning, the TV turned on fine and after a few minutes horizontal lines appeared and the screen went black, after 5 or 10.
It would work fine for a few minutes, and as long as you didn't turn it off, it looked perfect. I changed the SMD capacitors.
c981, c1068, c226 and c9?6 I'm not sure about this one because I can't see it in the photo I'm sorry, the TV is working fine, it looks very good.
and it doesn't do anything strange anymore except when I connect the multimedia disc through the HDMI, it shows stripes and gets stuck
It takes about 10 minutes, but I was already doing that; little by little, only the multimedia disk failure in the HDMI remains.
Thank you for everything.

Solution in 42LC55 - LG
I have changed the SMD capacitors c981 of 47uF 35v, c1068 of 100uF 35v, c226 of 100uF 35v, and c9?6 of 100uF.
35v can be replaced with normal capacitors as you can see in the photo.

Fault resolved in LG 37LF65

Symptom or defect of the TV There is no image, but there is sound.

63
Solution in LG - 37LF65
In the power supply, the capacitors on the secondary side are replaced but it still fails. It is discovered that
The inverter has other capacitors in poor condition, they are also replaced and the TV is repaired.

Fault resolved in LG 42LG3000

Symptom or defect of the TV
The image goes full of stripes or a white screen, then after half an hour it gets better.
Solution in LG - 42LG3000
I notice that touching the panel solves the problem and a bad connection is detected in the flexible cables of the panel.
I put a rubber band putting pressure between the chassis and the panel cable and it works correctly.

120. Issue resolved in Samsung PS43E450

Symptom or defect of the TV: Sound is heard but there is no image.

64
Solution in Samsung - PS43E450
It is observed that there is no VS voltage because the VSOn line coming from the control board is never active.
I assume that the output from the micro is open collector and is not powered by any voltage. I apply 3V3.
from the leg 8 of the memory and now there is an activation line VSon when it should be there and cuts when it is
go to Standby.

Fault resolved in PHILIPS 37PFL7662D/12

Symptom or defect of the TV When it is turned on, it shows an instant and is left only with sound.
Solution in PHILIPS - 37PFL7662D/12
I am heading to the inverter and measuring the transformers checking that one of them has an altered output, it is a
6016B, since it's out of stock, I put a 6024B and it works correctly.

122. Malfunction solved in LG 37LC2RR

Symptom or defect of the TV

It doesn't turn on, the pilot tries to change state but goes back to red.

Solution in LG - 37LC2RR
The power supply is missing the 12V that comes from the DC-DC converter made up of the integrated circuit U200 and
the two transistors packaged as an integrated circuit next to it. The U200 is an IRU3037, it is replaced by one
new and the TV works perfectly.

65
 123. Breakdown resolved in LG 32LE5500

Symptom or defect of the TV

Many times you push the button to start and it doesn't turn on, all the indicator lights come on but it doesn't start. Other times it does.
that ignites.
Solution in LG - 32LE5500
After many checks, it was decided to replace the power supply and the device works.
correctly, it does not fail again.

124. Fault resolved in JVC LT-32C50BU

Symptom or defect of the TV

When connecting the TV, the relay sounds and the blue indicator blinks intermittently without turning on.

Solution in JVC - LT-32C50BU

When measuring at the outputs, I have no voltage. I measure at the primary capacitor and I also do not have the 300V.
230V arrives as usual. I continue checking and reach the R9202 of 8.2 OHM and 6W which is faulty. It is replaced and
TV solved.

66
 125. Fault resolved in LG M1994DJ

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in LG - M1994DJ
In the power supply, the integrated circuit STRW6252 in position U101 is replaced and the TV works.
perfectly.
126. Issue resolved in SAMSUNG L332A336J1D(XXC)
Symptom or defect of the TV
At certain times, several channels were pixelated. Sometimes it was very difficult to turn it on when giving the command to
through the remote control.

Solution in SAMSUNG - L332A336J1D(XXC)

The equipment has been intervened and everything appears to be correct, at first glance, in the power supply and main board.
I first checked the referred source (BN44-00192B) by locating the solder joints of transistor QB802.
cracked (cold). The tin of origin (of very poor quality) was removed and the transistor was re-tinned.
He set up the fountain and the TV was tested for a week for many hours a day and it hasn't returned to...
to fail.

67
 Fault resolved in Samsung PS-42E7SX

Symptom or defect of the TV It can be heard but not seen.

Solution in Samsung - PS-42E7SX
The problem is one of the integrated circuits on the Ysus buffer board. The integrated circuit is the SN755870. I haven't been able to
repair the TV because I have not found the complete board with ref. BN81-06992A as it is out of stock.

[Link] resolved in LG 26LH2000

Symptom or defect of the TV
The television in question does not turn on. The standby light appears in red and when trying to turn it on, it blinks and
it turns red again.
Solution in LG - 26LH2000
The voltages of the power supply (LGP26-09P) are reviewed, and it is verified that we do not have the 12v for the
Main. The diode D256 (SB360) is replaced and the television is working.

68
 Fault fixed in Toshiba 22EL833G
Symptom or defect of the TV: It only tunes into some TV channels.

Solution in Toshiba - 22EL833G

The tuner with reference DTOS403LH122E is replaced and an automatic channel search is performed. Once
All channels can be seen.

130. Malfunction solved in LG 32LC2DB

Symptom or defect of the TV
It took a long time to turn on. It finally stopped working, even while being connected for quite a while...
Solution in LG - 32LC2DB
Very robust LCD TV, you have to spend quite a while removing screws and shields to reach the boards...
several swollen capacitors are observed in the power supply module. They are 1000uF/25V and 130º.
They are replaced with ones of equal capacity, but of 35V 130º and the TV works again without issue.

131. Malfunction resolved in Gateway LE1936

Symptom or defect of the TV
I have a Gateway monitor model LE1936, and suddenly it does not display an image; the power button is not working.
It blinks intermittently. I tried connecting another monitor to my computer and it works perfectly, so
Without a doubt, what is wrong is the monitor. What could it be?

69
Solution in Gateway - LE1936 Change of 47mf capacitor to 50 volts.

132. Malfunction fixed in Samsung LN32A330J1

Symptom or defect of the TV

solarized or negative image and it is caused by the multiplexer circuit located on the T-CON Board.
License plate AS15 - G, sometimes it is resolved by redoing it since it overheats too much.
false contacts or cold solder joints occur, but for this you will need to have a soldering station.
hot air is the same to replace it, if you do not have this equipment you must replace the entire T-CON Board.

Solution for Samsung - LN32A330J1

solarized or negative image caused by the multiplexer circuit located on the T-CON board brings the
registration AS15 - G

70
 133. Fault resolved in Samsung UE22D5003BW

Symptom or defect of the TV It does not turn on, it does nothing.

Solution in Samsung - UE22D5003BW
The power supply is checked and the diode DM887 is found to be shorted. It is replaced with a new one and the TV
It is perfectly repaired.

Malfunction resolved in PHILIPS 37PF9946/12

Symptom or defect of the TV
It tries to turn on and disconnects, the relay clicks several times, when heating the power supply with a hairdryer it turns on.
and it works OK.

Solution in PHILIPS - 37PF9946/12

C8294, C8293, C8227, and C8224 are changed, and it is resolved.

[Link] resolved in SANYO CE32LD81-C

Symptom or defect of the TV
Standby pilot in blue. We give the command to turn on, it tries, but immediately returns to the position of
wait (STBY). And so in each attempt. It does not start.

Solution in SANYO - CE32LD81-C

Initially, I suspected the power supply. All output voltages were tested, having
disconnected the Main previously, which led me to discard the referred source 17PW20. I tested this same one.
on another TV and it worked well for several hours. Therefore, I became suspicious of the main one which was replaced once
Another new one, the TV is working perfectly again.

71
 [Link] resolved in Sony KDL-20G2000

Symptom or defect of the TV The bluish image appears and is somewhat solarized.

Solution in Sony - KDL-20G2000

The problem seems to be the display, but looking at another failure, it is described that the failure is in the T-CON.
specifically in the AS09G integrated circuit, this integrated circuit is replaced and the TV is perfectly repaired.
the position of the integrated circuit is IC502.

Malfunction resolved in PHILIPS 32PFL5405H/12

Symptom or defect of the TV.

It won't turn on, the LED flashes red. It flashes in a sequence of three.
Solution in PHILIPS - 32PFL5405H/12
Replacement of the diode SB3200 at position D210 in the power supply.

72
 138. Breakdown resolved in Samsung LE26C350D1W

Symptom or defect of the TV

The image flickers, the backlighting is not fixed and is intermittent when it wants.

Solution in Samsung - LE26C350D1W

At first I think it's a display problem, but by taking measurements at the source, I confirm that the
the problem comes from pin 6 of the integrated circuit in position IC1801 (LX6523), this pin is the one called Enable and
is controlled by the transistor Q1814. The way to deactivate this enable input is to put the base of this
transistor to mass. Before doing this, I change the transistor, the optocoupler, and also the capacitor C815 from the
primary of the source. If you see in the diagram it all goes in the same line. You can download the diagram from the source.

73
BN44-00368B from Elektrotanya. In the end, the solution was to disable this enable line by putting the base of
Q1814 to the mass.

Fault resolved in Hitachi 37LD6600

Symptom or defect of the TV
No sound through scart connector.

Solution in Hitachi - 37LD6600

Power supply change c863-1000-16v.

Fault fixed in LG 37LG3000

Symptom or defect of the TV You turn it on and the indicator light starts to blink.
Solution in LG - 37LG3000
I try to lift the eeprom IC105 and the TV turns on, so I put in an empty 24C256 and the TV works.
Okay, I will do an automatic search and all the channels will be found.

[Link] fixed in Sony KDL-20G2000

Symptom or defect of the TV
Negative screen, or with too much brightness. The teletext comes out fine.
Solution on Sony - KDL-20G2000
Fault located in t-con module, changing the IC model AS09g.
74
 142. Breakdown resolved in JVC LT-26DA8ZU
Symptom or defect of the TV
It lights up for a moment and then darkens again. The sound remains.

Solution in JVC - LT-26DA8ZU

It is observed that the failure is from the inverter. I measure the transformers and locate one that measures differently. For
to make sure this is the problem I remove the protection of the inverter temporarily by putting an LED diode
on pin 10 of the control integrated circuit and the screen remains lit except for the lamp that controls
the defective transformer. The transformer with ref. 4001Y is replaced and the LED diode is removed to leave the
active protections, but now it is no longer protected and the television is visible perfectly.

143. Issue resolved in LG 37LC2D

Symptom or defect of the TV

It has image but no sound.
Solution in LG - 37LC2D
The sound chip is replaced but it remains the same. It is observed that the speakers are short-circuited. They are replaced.
The speakers and the TV sound perfect.

75
 144. Fault resolved in SAMSUNG PS50A417C2D
Symptom or defect of the TV
Both MOSFETs QS801 and QS802 18N50, and F803 FUX 8 amp from the power supply are replaced and sound comes out with a black screen.

Solution in SAMSUNG - PS50A417C2D

Before changing anything from the f.a. look at its LJ41-05120A. The whole board was crossed, uneconomical. Because the 2
MOSFET from f.a. 28.50€ bought on eBay, and the y-sus 240€, and if you don't change the z-us, it will break in 15 days like this.
It's better not to look at them, at the price they are now.

Fault resolved in Philips 32PF5321

Symptom or defect of the TV

Occasionally, when turning on the TV, there is sound but no image, without backlighting.

Solution in Philips - 32PF5321

The problem is caused by the display lamps that sometimes trigger the protection of the
inverter. It doesn't mean that the lamps are completely faulty, but that their characteristics have varied a little.
The solution I give to this TV is to disable the protection so that it always lights up. The way to disable this
Protection is to place a LED diode at the ends of the capacitor C216 that is connected to the protection pin.
from the control integrated. This way we ensure that the voltage will never rise above 0.7V. The TV is tested during
One week and it works correctly.

76
 Fault resolved in Philips 42PF7520D

Symptom or defect of the TV It doesn't turn on, the light keeps blinking red.
Solution in Philips - 42PF7520D
In the power supply, some 100uF SMD capacitors need to be changed, as well as other SMD ones.
near the integrated circuit seen in the third photo.

147. Breakdown solved in LG LH2000

Symptom or defect of the TV
Red LED blinks 5 times, then turns off and repeats, and does not switch to blue LED, if you measure the voltages on the source of
Power supply with inverter, all voltages are fine.
Solution in LG - LH2000
Change Q302 P2503NPG. This Q302 has 8 pins and is in the power supply.

77
 Fault resolved in Samsung LE40A656
Symptom or defect of the TV
The device does not turn on, it does nothing, blinking indicator.

Solution in Samsung - LE40A656

In the power supply, I find two swollen capacitors. I replace all the capacitors in the
power supply and the TV is repaired.

[Link] fixed on SONY KDL-40EX721

Symptom or defect of the TV Se ve con doble imagen, como si estuviese en 3D.
Solution for SONY - KDL-40EX721
The display is malfunctioning; if the double image appears vertically, it's the display. If it appears horizontally, it has never happened before.
this model, this is a confidence from a Sony SAT. I say the sin but not the sinner

150. Fault resolved in JVC LT-32DH8ZG

Symptom or defect of the TV
It doesn't turn on, the indicator light stays red.

78
Solution in JVC - LT-32DH8ZG
In the power supply, I locate several swollen capacitors. To be on the safe side, I change all of them.
what's in the fountain and the TV works perfectly, functioning like the first day.

Fault resolved in LG 42LG5000

Symptom or defect of the TV
Everything is correct, but when you try to turn it off, it shuts down and then turns back on.
Solution in LG - 42LG5000
The fault is in the Power Supply Unit (PSU)

Fault resolved in SAMSUNG LE37M87BD

Symptom or defect of the TV
Sometimes the image turns black with vertical stripes or there are failures in parts of the screen.
Solution in SAMSUNG - LE37M87BD
Observing the symptoms, it seemed like a panel failure. The soldering of the lamps was checked and they were
They were repaired, and also the inverter transformers, and the TV no longer presents the failure. The problem was that being
The bad soldering created electrical noise that affected the video signals.

Fault resolved in PHILIPS 37PFL7662D/12

79
Symptom or defect of the TV
The TV displayed the image with distorted colors and sound.
Solution in PHILIPS - 37PFL7662D/12
The AS15-F of the t-con is replaced and now the image appears in negative. After checking everything in the menu of
Service and thanks to a user of this forum, the original data is installed in the EEPROM of the T-con since it was
damaged and the TV works perfectly.

154. Issue resolved in TOSHIBA 42SL738G

Symptom or defect of the TV
Blue fixed pilot, does not start without sound.

Solution in TOSHIBA - 42SL738G

The [Link] is reviewed and R961 is hot. The transistors Q961 and Q962 are measured and are in
SHORT. Change the components and TV solved.

Fault resolved in PHILIPS 42PFL8654/12

PHILIPS - 42PFL8654/12
Symptom or defect of the TV
It doesn't turn on. It also doesn't indicate standby.

Solution in PHILIPS - 42PFL8654/12

The TV was turned on and the power supply module was visually inspected, nothing abnormal was noted. Neither
the main board, so the usual process is followed, making measurements, locating the D911 short.
unsolder and it is checked that it is a Shokky of 60V 2A, an SB260. Once replaced, the TV returns to
to function properly for several hours without exceeding the mentioned component, which is why it is given
the breakdown has been fixed.

80
 156. Breakdown solved in Samsung 2032MW

Symptom or defect of the TV

It won't turn on, it doesn't do anything.

Solution in Samsung - 2032MW

Several swollen capacitors are observed in the power supply, all are replaced and the TV works.
perfection.

Fault resolved in LG 32lg3000

Symptom or defect of the TV
When turning on, the red LED blinks 3 times and then turns blue, the TV does not turn on, sometimes it turns on... randomly.

Solution in LG - 32lg3000
If you visually see the capacitors well, don't think about it anymore, change R609, 610, 611, 612 to 6290K though
be sure when measuring them with the tester, before changing check that at the terminals of the main filter, C608 and C609
there is around 185...190V if it drops much below this value there is no doubt. I usually put in series instead of the
SMD resistors: 2 resistors of 1M and one of 470K.

[Link] fixed in Philips 42PF5320

Symptom or defect of the TV
It does not turn on. The indicator stays red.

Solution in Philips - 42PF5320

In the power supply, there are two swollen capacitors of 3300uF. All of them are changed.
nearby area and the TV works well.

81
 [Link] resolved in LG 22LE3300

Symptom or defect of the TV

It doesn't tune into any channels and the antenna is fine.

Solution in LG - 22LE3300
The TDTJ-S001D tuner is replaced and an automatic channel search is performed, and now it finds them.
all available channels.

[Link] resolved in LG 32LP1R

Symptom or defect of the TV
It doesn't turn on, and when it does, it takes a long time to do so.

Solution in LG - 32LP1R
In the power supply, all capacitors need to be changed, both those in the primary and those in the secondary.
secondary.

[Link] repaired in Sanyo 20 LCD

Symptom or defect of the TV
It doesn't turn on, it doesn't do anything, not even the indicator.

82
Solution in Sanyo - 20 LCD
The power source is observed and it is verified that the power fuse is open. The bridge diodes are measured and
I find 2 of them short, so I decide to change all four and put in the fuse. The TV is repaired.

161. Malfunction resolved in LG 32LC2

Symptom or defect of the TV
There's a very annoying noise coming from the speakers.

Solution in LG - 32LC2
The power supply is inspected and several swollen capacitors are observed. All the capacitors in the power supply are replaced and the TV remains
repaired.

162. Fault fixed in SONY KDL-26U2000

Symptom or defect of the TV
Black screen with sound, +24v reach the inverter, and it has electroluminescence, in the power supply all voltages.
good.
Solution in SONY - KDL-26U2000
On the [Link] to the right of the connector, there is an SMD fuse, cp101p-in, it is not a capacitor, it is an SMD fuse and it receives +5v
esta cortado, se puede hacer un puente, y ok.

Fault resolved in LG 32LC56

Symptom or defect of the TV
It takes a long time to turn on, the indicator stays red.

83
Solution in LG - 32LC56
In the power supply I find several swollen capacitors, I replace all of them and the TV is fixed.

164. Breakdown resolved in PHILIPS 37PFL5603D

Symptom or defect of the TV
Very dark image.
Solution in PHILIPS - 37PFL5603D
The image looks very dark and leaves a mark; when an image is on the screen for a while and then changes, it shows.
the trace of the previous one. There are doubts about the AS15F of the t-con even though it does not heat up. It is replaced and the TV is visible

perfectly.

Fault resolved in SAMSUNG LE32B350

Symptom or defect of the TV
White image with stripes on the screen
Solution in SAMSUNG - LE32B350
The panel is disassembled and at the connection of the flex that goes to the t-con, it can be seen that liquid has spilled (it goes along the bottom part).

from the panel) and it is rusted and the flex is corroded. The connector is cleaned to remove the rust and the flex is changed and the TV
it is repaired.

Fault resolved in SAMSUNG LE23R86BD

Symptom or defect of the TV
The TV does not turn on, the LED blinks.

Solution in SAMSUNG - LE23R86BD

The problem is with the 5V standby that is intermittent in cycles of 1 second. The issue is the KA431A.
with position ZDTB852 which activates the optocoupler that informs the Viper12A oscillator that the 5v are present
presents. When this signal does not reach the oscillator, it enters a start-stop cycle.

84
 Fault resolved in Sanyo 32 inches

Symptom or defect of the TV

Black screen, I can't remember which model it is. It has backlighting.
Solution in Sanyo - 32 inches
I check the T-CON and I see a 2.5V regulator that only has 0.8V. I place another 2.5V regulator that is similar to the
original but adapting it and the TV works perfectly.

168. Fault resolved in LG 32LC56

85
Symptom or defect of the TV
Sometimes it turns on, other times it doesn't. Other times it is on and then it turns off. It does weird things.

Solution in LG - 32LC56 The L202 coil is on the mainboard, next to the connector.
that comes from the source.
Since there are times it doesn't turn on, I think the problem is with the power supply and I replace it, but the problem
continue. After reading many breakdowns on the internet, there is one that says that the voltage step coils in the
I remove all these coils next to the input connector, and they short circuit to ground. I take all these coils off and put a
thread in its place, once the TV is fixed it does not fail again.

Fault fixed in Sony KDL-32U2000

Symptom or defect of the TV
The screen lights up for a second, the red pilot comes on with sequences of 4 blinks.
Solution in Sony - KDL-32U2000
Change a lamp. (It was off.)

170. Breakdown resolved in LG M228WDP-BZ

Symptom or defect of the TV
The blue LED blinks more than three times, blinks until it heats up, then the LED stays fixed, an image appears without
sound, and it does not respond to the command or the keyboard.

Solution in LG - M228WDP-BZ
The power supply is repaired. 5 capacitors of 1000uF 25V that look swollen are replaced. Done.
It turns on on the first try but still doesn't respond to the remote or the keyboard. I changed the EEPROM.
24C512W=24C512A, this EEPROM is on the main board, next to the 8-pin IC.

171. Malfunction resolved in LG FLATRON M2794-DJ

Symptom or defect of the TV
Al encender da un parpadeo el Led azul, se apaga, se vuelve a encender y se queda fijo sin encender nada.

Solution in LG FLATRON - M2794-DJ

After changing the EEPROM and having no luck, I decided to change the main control board and it worked. Then you have to
adjust because the factory Menu comes.

172. Fault resolved in SAMSUNG LE32S73BD

Symptom or defect of the TV
I have a 32-inch LCD SAMSUNG LE32S73BD television that won't turn on, the red power LED is on.
The front blinks when trying to turn it on (about 0.5 seconds per blink). I have opened it and measured voltages.
at the output of the power supply (BN96-03775A), in the connector CNM801 that connects the board
Power supply and the Main board, using a digital multimeter, this is what I obtain: output of 5V: from 2.1 to 0.7 V

86
intermittent, changing every 0.5 seconds just like the power LED. output of 12v: from 3.5v to 1.8v,
intermittent, changing every 0.5 seconds like the power LED. So I assume this board
It's broken. I don't see any bulging electrolytic capacitors. The fuse is fine. Am I correct? This is the
It's the first time I'm trying to repair a monitor, although I have repaired other things before. Thank you very much.

Solution in SAMSUNG - LE32S73BD

SOLUTION: I changed the F9222L integrated circuit on the power supply board and it is working well now. A user
He responded to my inquiry and suggested changing it, as he had seen more failures like this. Thank you! I asked for the
integrated by internet, I believe it was on eBay, it cost me about 10€ including VAT and shipping costs (I don't remember well)
the price).

Fault resolved in LG 32LC55

Symptom or defect of the TV

After a few minutes, the image starts to flicker until it completely goes dark but with
audio, Regardless if it is with TDT (TV), SCAR or HDMI
87
Solution in LG - 32LC55
After searching this website, I saw that there was a malfunction that had the same symptoms as my TV.
from the capacitors of the 3.3V regulator, but in the photo the board was not identical, but it does have that
regulator and yes, it has that symptom, with the diagram look for the famous capacitors C970 and C958 of
I have replaced the 100uF/16V with a 220uF/35V. Now it works perfectly, as a preventive measure I have changed.
all the electrolytic capacitors of the power supply since some were swollen (about to
short-circuit or reduced its capacity

174. Fault resolved in Samsung LE26C350

Symptom or defect of the TV
It doesn't turn on, it does nothing.

Solution in Samsung - LE26C350

The power supply is observed and it is noted that one of the output diodes from the supply is shorted.
replace this with a BYW95 and the TV works fine.

[Link] resolved in LG 47LH3000

Symptom or defect of the TV

It doesn't turn on, the LED blinks but then stays on.
Solution in LG - 47LH3000

I replaced the electrolytic capacitors of the power supply but it keeps failing. In the end, I decide to replace the power supply.
complete.

88
 Fault resolved in LG M227WD

Symptom or defect of the TV

The screen lights up for a moment and then darkens, the sound remains.

Solution in LG - M227WD
The power supply and the inverter are checked, but nothing abnormal is observed. When you turn it on, a noise can be heard coming from it.
The display is disassembled and one of the lamps is seen with the cable's soldering very overheated.
Everything is cleaned and resoldered, leaving the TV perfectly repaired.

Malfunction resolved in Philips 32FD9944

Symptom or defect of the TV
It won't turn on, the pilot light is blinking red.

89
Solution in Philips - 32FD9944
Heat is applied to the source but it doesn't ignite. In the end, I decide to replace all the capacitors.
electrolytics in the power supply and the TV turns on and displays correctly.

178. Fault resolved in Philips 22PLF5403D/10

Symptom or defect of the TV
Black screen, only the menus appear, a window says that "there is no video signal" in none of the
There are no inputs in TV mode. When trying to change channels, it only cycles between ext, hdmi, pc, svdc, and tv.

Solution in Philips - 22PLF5403D/10

Enter service mode by pressing 062596 + the INFO button, and in the menu that appears, we delete the errors.
we turned it off, disconnected for 30 seconds and done!!!

[Link] resolved in Philips 46PFL5605H

Symptom or defect of the TV
It doesn't turn on, the LED is blinking.

Solution in Philips - 46PFL5605H

I test the power supply in idle mode without connecting anything else and I trick it to have all the voltages.
It works well, so the fault is in the mainboard. It is replaced with a new one and the TV is repaired.

Look for the Power_On line and activate it with 5V, then you will have all the voltages from the source. Next, look for the
Inverter line On and activate it with 5V, this way you will have the lamps illuminated.

90
 180. Breakdown resolved in Philips 32FPL5522D/12

Symptom or defect of the TV

Screen with stripes as soon as it is turned on, it turns off and works for a while and then it comes back.
Solution in Philips - 32FPL5522D/12
The T-CON soldering and data buses and cables are checked, finding a faulty LVDS cable which is replaced.
perfect to function.

Fault fixed in Philips 20PF4121

Symptom or defect of the TV
It doesn't turn on, not even the pilot light.

Solution in Philips - 20PF4121

Diode SR306 position 6211 in secondary source shorted. It is replaced and working.

[Link] resolved in Samsung LE32S71

91
Symptom or defect of the TV
The pilot light turns red and blinks a few times, but the TV does not turn on.
Solution in Samsung - LE32S71
All the source voltages are low or not present. The integrated circuit with position ICM801S is replaced.
that in a F9222L the power supply turns on correctly with all the voltages and the TV looks good.

[Link] resolved in Samsung UE22C4010

Symptom or defect of the TV
The TV works well but the image is very pixelated.

Solution in Samsung - UE22C4010

After reviewing everything, I decide to replace the tuner with reference DTOS40CVH081A and the TV is repaired.
no pixel.

92
 184. Fault resolved in LG 32LH2000
Symptom or defect of the TV
It doesn't work, it just tries to start with a flashing red LED, briefly shows blue, and then turns off.

Solution in LG - 32LH2000
Power supply EAY58582801 is replaced with a new one and it works.

185. Malfunction resolved in LG RZ26LZ55

Symptom or defect of the TV
No backlight. Light. (French)
Solution in LG - RZ26LZ55
I had the same symptoms as another TV, and I solved it by replacing the inverter. I had the same symptom with
another one that I solved by changing the inverter.

186. Malfunction resolved in LG 42LK450

Symptom or defect of the TV
It has backlighting and sound but no image.
Solution in LG - 42LK450
Upon connecting the TV, we noticed it has sound and backlighting but no image. Reviewing all the
connectors we reached the flex that connects the main with the t-com and the image goes and comes back. I remove the connector, clean it and the
the device works well.

[Link] resolved in Samsung 943NWX

93
Symptom or defect of the TV
Nothing turns on at all, not even the Stand By LED. It is dead.
Solution in Samsung - 943NWX
Finally, the problem was solved by changing the transistor or regulator U101 (DM0465RE) marked in the image.

188. Malfunction resolved in LG 42PX4RV

Symptom or defect of the TV

Nothing turns on. The indicator doesn’t light up either.

Solution in LG - 42PX4RV
The problem lies in the power supply, more specifically in the Standby power supply, which is the one that drives the chopper.
small and the integrated STR A6151. Before changing the integrated, I replace two capacitors that are on the
primary and another three that it carries in the secondary, and then the TV turns on, so the fault was caused.
for these capacitors.

94
 189. Fault solved in LG M2262D
Symptom or defect of the TV
It starts, the image appears in a reddish tone for two seconds and then the image disappears. The sound is correct.

Solution in LG - M2262D
One of the lower lamps is malfunctioning. By powering them one by one, it can be seen that the lighting of the one that is faulty is
in a reddish tone.

190. Repair completed on LG 37LC2D

Symptom or defect of the TV

The TV can be heard but the image cannot be seen.

Solution in LG - 37LC2D
The inverters 6632L-0197C are replaced, but the TV continues to malfunction. The LCD panel is disassembled and it is checked that
there is a derivation to mass in the connections of the lamps. It is decided to cut the metal connection and a
bridge with high voltage cable so that there is no arc flash. Once the TV is done, it works well.

95
 [Link] resolved in LG LG32LB75

Symptom or defect of the TV

After a while of working, stripes appear and it remains with backlighting, sound is okay.
Solution in LG - LG32LB75
C570 and C958 SMD of 100/16v

192. Fault resolved in Samsung LE32B350F1W

Symptom or defect of the TV

It turns on perfectly but the screen doesn't light up, the sound is correct.

96
Solution in Samsung - LE32B350F1W
The source is reviewed, specifically the circuitry of the inverter, and one of the transformers is observed to be open.
I am looking for a new transformer but I can't find it anywhere, so I decide to replace the power supply.
complete with ref. BN44-00289A for the BN44-00289B which is fully equivalent and the TV will be repaired.

Fault resolved in LG 26LX2R

Symptom or defect of the TV

When plugged in, the Standby LED lights up and after a second it turns off.

Solution in LG - 26LX2R
Capacitor C221 of 100uF at 16V that has lost its value. The source is: YP2632T
97
 [Link] resolved in SAMSUNG LE32A336J1NXXC

Symptom or defect of the TV

It is heard but without image.

Solution in SAMSUNG - LE32A336J1NXXC

Bad soldering on the power supply, specifically on the Mosfets. They are very clear, just rework them and it's resolved.

195. Fault resolved in LG M228WD

Symptom or defect of the TV
It doesn't tune into any channel.

Solution in LG - M228WD
The tuner with reference TDFC-G108P is replaced and the TV is repaired. It is now tuning into the channels.

98
 196. Fault resolved in SAMSUNG LE40A656A1F

Symptom or defect of the TV

The red LED blinks slowly, continuously, and there is no image or sound.

Solution in SAMSUNG - LE40A656A1F

Replacement of secondary F.A. Change CM 804 of 1000 mic 25v. Change CM 809 of 1000 mic 10v. Change CM 812 of
1000 mic 10v. They look swollen.

Fault resolved in Samsung LE37B530P7W

99
Symptom or defect of the TV
The greenish image looks very bad.

Solution in Samsung - LE37B530P7W

You need to enter the Service Menu by pressing Power Off, Info, Menu, Mute Power On. Then you need to go to the
ADC/WB option and set the image values as seen in the second photo. I have set them like this and the image is
go well.

198. Fault resolved in TOSHIBA 23DL933G

Symptom or defect of the TV
Dead, not even the standby LED lights up.

Solution in TOSHIBA - 23DL933G

In the secondary of the power supply, the D709 with reference SB5100 schottky is crossed. I put a STPS.
5L60, it's a Schottky of 5 amp, and okay. It should yield +11.2v.

100
 199. Fault resolved in Philips 42PES0001H
Symptom or defect of the TV
The image looks very bad, like it's solarized.

Solution in Philips - 42PES0001H

The T-CON is disassembled and I notice that it has the AS15F chip, it is replaced with an AS15G and the TV works.
perfectly.

200. Issue resolved in Samsung LE32B350F1W

Symptom or defect of the TV
The TV turns on but the screen does not light up.

Solution in Samsung - LE32B350F1W

The fault is in the inverter which in this case is on the same board as the power supply BN44-00289A. The measurements are taken.
output transformers and I observe that one is open. This transformer is replaced and the TV remains
repaired.

101
 201. Fault fixed in SAMSUNG LE432A436T1D
Symptom or defect of the TV
The LED blinks, it turns off but the TV does not turn on.
Solution in SAMSUNG - LE432A436T1D
The power supply was examined without observing any anomalies. It was removed, inspected, and solder joints were located.
cold in the soldering of transistor Q811. These and other suspicions are resolved, it is mounted in the module in the TV and
it works perfectly. The power supply in question is a BN0044-213A, which is installed in various models
the brand, like the LE32A336J1D, has the same fault reported by another colleague.

202. Malfunction fixed in LG 32LC2DB

Symptom or defect of the TV

It won't turn on, the light goes green but nothing else.

Solution in LG - 32LC2DB
The power supply is checked and the capacitors are fine, the only thing I notice is that one of the voltages marked as
6V is not present. I follow the line of these 6V and reach two SMD integrated format MOSFET transistors of 8.
pegs that are controlled by another integrated oscillator called IRU3037. From this one, the oscillation does not come out for
Activate the transistors. The IRU3037 is replaced and the TV has 6V and works perfectly.

102
 [Link] repaired on LG 32LE2R
Symptom or defect of the TV
Only the pilot light turns red and neither the screen lights up nor is there any sound.

Solution in LG - 32LE2R
The power supply is checked and all that is noticed are several bulging capacitors. I replace all of them.
secondary and the TV works perfectly.

[Link] resolved in TOSHIBA 23WL46G

Symptom or defect of the TV

The pilot light stays on. There is no sound or image.

Solution in TOSHIBA - 23WL46G

The inverter works, as the screen lights up. Heat and cold are applied to the board until it
It determines that the capacitor in Photo B (C903) 100uF at 35v is the one causing the problem. It is replaced and works fine.
working. In the photo, the capacitor is shown above so that it is clear which one is being replaced. I have
placed one of 100uF at 63v.

103
 [Link] resolved in LG 32C460

Symptom or defect of the TV

Black screen, there is sound and there is backlighting.
Solution in LG - 32C460
In the T-CON, the open fuse F1 and a short circuit at its output are checked. Several components are desoldered.
capacitors to find out where the short comes from until it reaches the integrated circuit US1 which is the one that produces
the short. The solution is to replace the entire T-CON.

206. Fault resolved in LG 22LV2520.

Symptom or defect of the TV

It works well but the TV channels pixelate and sometimes there is no signal at all.
Solution in LG - 22LV2520
The TDTJ-S001D tuner is replaced and the TV works well even though I perform another automatic search.
of channels to renew the channel list.

104
 207. Malfunction resolved in Samsung LE32R86
Symptom or defect of the TV
When it's been running for a while, the image pixelates and looks bad.

Solution on Samsung - LE32R86

On the mainboard, all the electrolytic capacitors located under the cooler and the TV are replaced.
it is repaired.

[Link] resolved in LG M1931D

Symptom or defect of the TV

It doesn't work, the light stays red and nothing else.
Solution on LG - M1931D
The feeder is checked and it seems fine. The mainboard is attempted to be repaired unsuccessfully. In the end, I decide to replace it.
the mainboard EBU61852011 and the TV is repaired.

105
 209. Malfunction resolved in Samsung LE22B450C4W

Symptom or defect of the TV

The image looks very colorful and very bad.
Solution in Samsung - LE22B450C4W
The problem is in the configuration. You need to enter Service mode by pressing the keys: Power-off, Info,
Menu, Mute, Power-ON Next, we select the CONTROL option, and then the Sub_Option.
Now we go to the LVDS_Format option and change it to Jeida, even if it is initially set to
Jeida, we change the value to Vesa and then put it back to Jeida. Once done, the TV looks good but with tone.
greenish. Now we go to the ADC/WB option and set the 2nd_R_Offset, 2nd_G_Offset, and 2nd_B_Offset to 113 and
the 2nd_R_Gain, 2nd_G_Gain, and 2nd_B_Gain at 144. This resolves it.

210. Fault resolved in PHILIPS 26PF5521D/12

Symptom or defect of the TV
Dead, does not turn on or standby.
Solution in PHILIPS - 26PF5521D/12
Change all the capacitors in the primary and secondary of the power supply, except the filter of the
+320V. (Note) I would start by changing C130 and C236 in the secondary because I was going to
changing and testing and the last two capacitors (C130 and C236) that I changed was when I
it turned on and everything is fine.

211. Malfunction resolved in SAMSUNG LE37R86BDX

Symptom or defect of the TV
Whitish screen, the image is barely distinguishable.
Solution in SAMSUNG - LE37R86BDX
Change IC AS15F SMD. It's on the [Link], this IC when it's faulty overheats and gets really hot, you can't even ...
to touch.

106
 212. Fault fixed in Philips 42PF5532D
Symptom or defect of the TV
It doesn't turn on, or when it does, it takes a long time to do so.

Solution in Philips - 42PF5532D

The fault is in the power supply which has several swollen capacitors. All of them are replaced.
inflated capacitors and the TV works well.

[Link] resolved in LG 37LF65

Symptom or defect of the TV
Two days after repairing the power supply by changing the capacitors, the TV turns on but
the screen does not light up.

Solution in LG - 37LF65
The reason for this defect is because the TV has been turned off for two days and the capacitors have cooled down.
mainboard. I apply heat to the mainboard with a gun and the screen lights up. I replace the capacitors
C970 and C958 of 100uF and the TV works well when cold and hot.

107
 Fault resolved in LG 32LG2000
Symptom or defect of the TV
No enciende, se queda el piloto en rojo y nada mas.

Solution in LG - 32LG2000
The power supply is tested in empty and works well. It is decided to replace the mainboard with ref. EBU54743207 and the TV
it works well.

[Link] resolved in LG FLATRON M2262D

Symptom or defect of the TV
With the remote control, it doesn't respond at all. Everything is fine with the front panel.

Solution for LG FLATRON - M2262D

False soldering in the L407 SMD, +3.3V arrives to power the receiver, but nothing was arriving at the receiver.
They have to receive V +2.90V, G +0V, O +2.90V. This L is in the main, you follow the connector of the receiver, where
Plug in the connector, you'll see it right away.

216. Breakdown resolved in LG RZ-37LZ55

Symptom or defect of the TV
It won't turn on, the light is red and doesn't change color.

Solution in LG - RZ-37LZ55
In the power supply, I find several capacitors of 1000uF, 680uF, and 470uF that are swollen. I replace them and the TV works.
good.

108
 217. Malfunction resolved in Samsung GH17TS

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in Samsung - GH17TS

The source is checked and I see that the network filter only has 175V, which means that the capacitor is
disabled. One of 150uF at 450V is connected but the monitor still does not turn on although now we do have
300V in the capacitor. The control integrated circuit of the source with reference TOP247FN is replaced and now yes that
it turns on, so it is considered repaired.

109
 Fault resolved in Philips 23PFL5522D
Symptom or defect of the TV
The red light comes on, and when you turn it on, it turns green and starts flashing.

Solution in Philips - 23PFL5522D

4 capacitors of 680uF that were swollen are replaced but the TV keeps failing. In the end, I have to
Change all, but until I change one of 220uF to 35V, the TV does not turn on properly.

Fault resolved in LG 32LD350

Symptom or defect of the TV

It does not tune to any channel.
The tuner with reference TDTJ-S001D is replaced and the TV is repaired.

110
 220. Fault resolved in PHILIPS 32PFL5604H
Symptom or defect of the TV
Turn it on, the image appears for a moment and disappears, leaving only the sound.

Solution in PHILIPS - 32PFL5604H

Typically, in these TVs, the power supply with inverter reference PLHL-T808 fails and is replaced, and the TV is repaired.
but this time I was able to repair it since one of the output capacitors of the inverter was shorted
with a value of 220pF at 2KV. In the end, I replaced the one that was shorted and three others that were charred. A
Once replaced, the TV has worked well.

Fault resolved in LG 37LF65-ZC

Symptom or defect of the TV

Dark screen with sound but no image.
Solution in LG - 37LF65-ZC
Two capacitors on the inverter board of 680uf 35v with low capacity are replaced and everything is resolved.

111
 222. Fault fixed in Hitachi L37V01E

Symptom or defect of the TV

It doesn't turn on, and sometimes it does turn on but takes a long time to do so.

Solution in Hitachi - L37V01E

The rear cover is removed and several swollen capacitors can be seen on the power supply. Two of
They are 4700uF and the others are 1000uF, all of them are replaced and the TV is fully functional.

223. Fault resolved in LG 47LE8500

Symptom or defect of the TV

The image pixelates a lot and sometimes ends up getting lost.
Solution in LG - 47LE8500

112
The antenna cable is checked and it is fine. It is decided to replace the tuner with ref. EBL60740402 with one with ref.-
EBL60740404 which is completely equivalent and the TV no longer pixels, it looks perfect.

224. Breakdown resolved in LG 32LC55

Symptom or defect of the TV
It doesn't turn on, the indicator light is red and nothing else.

Solution in LG - 32LC55
In the source, I see several swollen capacitors, it's a matter of changing them all and the TV will be like new,
functioning...

225. Fault resolved in SAMSUNG LE40R86BD

Symptom or defect of the TV

The television does not turn on. Central blue light turns on and red LED. We press to turn on the television and we hear the...
it turns on and then turns off again.

Solution for SAMSUNG - LE40R86BD

The power supply had some swollen capacitor, the 7 on the upper right side are changed.
They are 1000uf and 220uf. The television still does not turn on but is now supplying voltages to the main board correctly.
decide to change the EEPROM memory located at the bottom of the mainboard in the PCMCIA area for another empty one
(24c256 in SMD) and after 4 attempts to turn it on, the EEPROM is programmed (the television does this on its own) and
working.
113
 Fault resolved in JVC LT-32DH8ZG
Symptom or defect of the TV
The remote control is not working.

Solution in JVC - LT-32DH8ZG

The remote has been checked with the tester and works well. The infrared receiver that is missing is replaced.
working well and the TV already changes when you use the remote control.

Fault resolved in LG 50PG1000

Symptom or defect of the TV
It doesn't turn on, the relays can be heard.

Solution in LG - 50PG1000
In the power supply, there are 4 capacitors of 3300uF and two of 1000uF that are swollen. I replace them and the TV
It works well.

228. Issue resolved in SAMSUNG LE40C530F1W

Symptom or defect of the TV
Nothing turns on, not even the display.

Solution in SAMSUNG - LE40C530F1W

FM801S T3, 15AMP, CM815, 201K 2KV ceramic capacitor burned, this capacitor is next to the
STRW6052S in the refrigerator where the diode bridge is. You change the 2 pieces and OK.

114
 Fault resolved in PHILIPS 32PFL7762D
Symptom or defect of the TV
The image looks very bad, as if it were blurry.

Solution in PHILIPS - 32PFL7762D

In the T-CON I find the AS15G integrated circuit that fails quite often. I replace it and the TV looks perfect.

230. Fault resolved in LG 19LE3300

Symptom or defect of the TV
It doesn't tune in, it doesn't pick up any channel.

Solution in LG - 19LE3300
The main board is checked and the only thing that occurs to me is to change the tuner. I will install a new tuner.
with reference TDTJ-S001D and the TV receives all channels so it is repaired.

[Link] resolved in Samsung PS42C450B1W

Symptom or defect of the TV

When you turn it on, a reddish image appears.
Solution in Samsung - PS42C450B1W
Since I think what is wrong is the Y-SUS, I touched the potentiometers and by touching one of them I managed to
The image was perfect, but as it heats up, it turns reddish again, so I confirm that the Y-SUS is the issue.
It is faulty. I replace it with part BN96-13069A and the TV is repaired.

115
 Fault resolved in LG 32LC56

symptom or defect of the TV

When you turn it on cold, the image appears distorted.
Solution in LG - 32LC56
At first it seems like a display problem, but I change a few capacitors on the mainboard that are
I found a regulator and the TV works perfectly. Tested for three days and it's working fine.

116
 Breakdown solved in T.V. SHARP LC-20SH1E
Symptom or defect of the TV
It does not turn on.

Solution in T.V. SHARP - LC-20SH1E

In the power supply module, it uses two diodes D 7714 and D 7718, we need to have 6V. If we have 3.8, change one.
brown capacitor C7715 of 100kpf, is shorted or has leaks.

234. Fault resolved in T.V.L.G. 32LB75-ZB

Symptom or defect of the TV
Lines appear on the screen whenever it wants, and the image also disappears.
Solution in T.V. L.G. - 32LB75-ZB
On the MAIN board, there is a stabilizer IC 901 that inputs 5 V and outputs 3.3 V. Change two SMD capacitors of
100mf that are next to the regulator. C 958 and C 970.

[Link] resolved in Philips 32PF9641D

Symptom or defect of the TV
Sometimes it turns on without backlighting and other times it loses it after running for a while.

Solution in Philips - 32PF9641D

It is clear that the problem lies in the inverter. I have noticed that the issue is in the masses that
they make the inverter mounting screws against the display chassis. They have accumulated at the bottom
oxidation and do not make good contact. Both the terminals and the display chassis are sanded well so that they make a good
contact and the problem is solved forever. If we had installed a new inverter, it would have been resolved.
the problem but the following month it would be the same again since rust would have formed again.

[Link] resolved in LG 26LC55

Symptom or defect of the TV
It does not turn on, and when it does, sometimes there is no sound.

Solution in LG - 26LC55
In the power supply, it is observed that the capacitors are physically fine. Since I don't know what to do, I...
I changed all the capacitors and the TV works perfectly. In this case, the capacitors looked fine.
but they were really wrong, so even if they are not inflated, it doesn't mean they are fine.

117
 237. Breakdown resolved in Sanyo CE15LD17-C

Symptom or defect of the TV

You turn it on and the TV works but after two seconds it loses the backlight.
Solution in Sanyo - CE15LD17-C
At a glance, there are no swollen capacitors in the power supply, so I look at the inverter and the first thing I do is
remove the protections of the FAN7314 which controls the inverter. To remove the protection of the FAN7314
I make a bridge from leg 1 of it to Masa. Now the lamps no longer turn off and the TV works well.
As it is supposed there is a problem, I changed all the capacitors in the power supply and removed the bridge and now it's already...
The TV is not protected, so it was the capacitors that were wrong.

[Link] resolved in Philips 26PF5521D

Symptom or defect of the TV

You plug it in and neither the red nor the green light turns on.
Solution in Philips - 26PF5521D
In the main power supply, the capacitors of both the primary and secondary are replaced.
Once the pilot is changed, it lights up in red and we press the remote, and it turns green and the TV works fine.
In the third photo, you can see the capacitors that I have changed.

118
 239. Issue resolved in LG L225WS

Symptom or defect of the TV

It doesn't turn on, it doesn't do anything.

Solution in LG - L225WS
In the power supply, several swollen capacitors are located. I replace them all and the TV remains
repaired.

240. Issue resolved in Samsung LE26B350F1W

Symptom or defect of the TV

You plug it in, and you hear the typical Samsung power-on sound, the channel sound appears but it doesn't show up.
image.

Solution in Samsung - LE26B350F1W

119
One of the checks is that when plugging it into the workshop, the image is visible. I check the voltage of 220V in
there is 218V at home and I measure 230V in the workshop. For this reason, it doesn't work well. I check the power supply and
I found a DP805 diode shorted. I put in an equal diode and the TV works well in all outlets.

[Link] resolved in LG 19LH2000

Symptom or defect of the TV

You turn on the TV and the light blinks.

Solution in LG - 19LH2000
In the inverter + power supply, the defective P2503NPG integrated circuit is located, it is replaced with a new one and the TV
it is repaired.
Typical fault in this TV that can be confused with a fault in the mainboard. Thanks for sharing.

Breakdown resolved in Samsung 932MW

Symptom or defect of the TV
It doesn't light up but it does have sound for euro.

120
Solution in Samsung - 932MW
Bad inverter (source + inverter). Transformer of the inverter TMS19PMASC/EDC is replaced and TV repaired.
Purchased at Fersay.

243. Fault fixed in Samsung LE32A336J1N

Symptom or defect of the TV
It doesn't work, it does nothing.

Solution in Samsung - LE32A336J1N

The power supply is checked and cold solder joints are seen on the double diodes DM851 and DM853. They are reworked.
The welds and the TV work correctly.

Fault fixed in SAMSUNG LE32B350F1W

Symptom or defect of the TV
It doesn't work, there is no Standby, there is only voltage in the primary of the power supply.
Solution in SAMSUNG - LE32B350F1W
Fault located in the primary of the power supply, ZD804 diode with leakage, corresponds to 1N4740AS
10V ZENER, Replace.

121
 [Link] resolved in Samsung LE32A336J1D
Symptom or defect of the TV
It doesn't turn on, there are times when it does turn on.

Solution in Samsung - LE32A336J1D

The power supply is checked and poor quality soldering is observed on the transistor that is seen in the
third photo. The welds are reviewed and the TV works perfectly.

[Link] resolved in Samsung LE32A457C1D

Symptom or defect of the TV

There is backlighting and sound but no image.

Solution in Samsung - LE32A457C1D

122
The T-CON fuse is measured and it seems to measure well, but once we turn it on and measure the voltage, I see
that there is a voltage drop at the output of the fuse compared to the input. I measure the fuse again and
It is indeed wrong because it measures 25 ohms and it should measure 0 ohms. The fuse and the TV are replaced.
it works correctly.

Breakdown resolved in Philips 30PF9946

Symptom or defect of the TV

From Standby, the light is red; if you try to take it out of Standby with the remote, the light turns off and at
The rat turns red again.
Solution in Philips - 30PF9946
The usual thing is that the TV would turn on and the light would turn green. When pressing the remote to turn it on, there is no sound.
the relay. I check the circuitry of the relay and reach the transistor that activates it, an SMD that is fine, but the
The 4.7 ohm step resistor is open. I mark it with a red arrow in the second photo. I put a
new and the TV works perfectly.

Fault resolved in PHILIPS 42PFL5603D/12

123
Symptom or defect of the TV
Screen illuminated at the ends and the center remains dark. In addition, the source emits a noise.
Power supply that increases when the lamps are turned on by the inverter.
Solution in PHILIPS - 42PFL5603D/12
Electrolytic plate capacitor power supply - inverter C808 of 180uf. 450v, replaced in this case by not
find the same for 220uf.450v. marked with the white X in the photo, it is the one with +400v. that does not alter with the
failure, nor do the voltages of the +24v power supply fail, as well as several +12v and -12v.

[Link] resolved in SONY KDL40U2000

Symptom or defect of the TV
It turns on and after a few minutes it turns off, with the green light staying fixed and the red one blinking at intervals of 4.
times.

124
Solution in SONY - KDL40U2000
When disconnecting the inverter, I notice it makes the same fault. Therefore, I focus on this module. We resolder the
Transformers but does the same thing. I have resoldered the F003 0.5A fuse and it has not failed again.

250. Issue resolved in Toshiba 32AV555D

Symptom or defect of the TV

The greenish and dark image is visible, the user menu looks good.

Solution in Toshiba - 32AV555D

Since I see that the Menu looks good, I know that the display is working fine and that the problem must be with the configuration.
To solve this problem, a total reset of the TV is necessary. The steps are as follows: 1. Mute on the
I command and release. 2. Mute the remote again and hold it down while pressing the Menu key.
local button panel. 3. Now we are in Service mode and an S and some more info appear on the screen. 4. Press the key
The exterior and the screen stays red. 5. Press and hold the Call (i+) button on the remote while also
Press the button. By following these steps, you can reset the TV and it will restart with the installation screen.
with the perfect colors.

251. Breakdown solved in Samsung PS50C450B1W

Symptom or defect of the TV

It doesn't turn on, it only lights up the indicator and makes sound.

125
Solution in Samsung - PS50C450B1W
The VS and VA voltages of the power supply are checked and only appear for two seconds.
then they disappear. I start to isolate all the plates from the power supply and until I disconnect the Y-
The Y-SUS does not show the voltages correctly. I replace the Y-SUS with reference BN96-12952A and the TV works perfectly.
although I have to adjust the Y-SUS settings a little bit.

252. Malfunction resolved in LG 42px3rv

Symptom or defect of the TV

It doesn't turn on, not even the pilot.

Solution in LG - 42px3rv
It is observed in the power supply that the small standby power supply does not provide the 5V. I replace the
capacitors C121 and C122 and then it supplies the 5V and the indicator lights up. To prevent further failures.
I also replaced the secondary capacitors of this power supply, the three that are seen on the left in the third one.
photo next to C121 and C122.

253. Malfunction resolved in Samsung T200

Symptom or defect of the TV
The volume increases by itself.

Solution in Samsung - T200

I believe the problem is in the button panel; I disconnect it and the problem is fixed. Knowing that it is the button panel.
I completely substitute and the TV is repaired.

126
 254. Breakdown resolved in Philips 47PFL5604H

Philips - 47PFL5604H
Symptom or defect of the TV
It doesn't turn on.

Solution in Philips - 47PFL5604H

In the power supply, I start checking components and find diode D911 is shorted. It
I replaced it with a BYW95C and the TV turns on perfectly. TV repaired.
Another one like that... the original diodes are the SB 260 (60V. 2A)... I replaced them with the SB 560 (60V. 5A)

[Link] resolved in Samsung LE40A656A1F

Symptom or defect of the TV

It doesn't turn on, the light turns on but nothing else happens.
Solution in Samsung - LE40A656A1F
I locate a blown capacitor in the source. I replace all of the secondary ones and the TV turns on.
First. TV repaired.

127
 256. Breakdown resolved in LG 42LH4000
Symptom or defect of the TV
It doesn't turn on, it doesn't do anything.

Solution in LG - 42LH4000
In the power supply, I find a blown fuse. Upon inspection, I find a shorted transistor and several others.
crossed or open components. I decide to replace the entire power supply and the TV is perfectly repaired.

Fault solved in LG 37LC45

Symptom or defect of the TV
Black screen, if there is backlight and it can be heard.
Solution on LG - 37LC45
I substitute the SMD electrolytic capacitors on the MAIN board next to the ribbon connected to
for the T-COM, the capacitors are as follows: 1000 uf 16 V 22 UF 16 V x2 TV working, previously
I changed the T-COM, thinking that could be the problem, and it wasn't.

258. Fault resolved in Samsung LE40C530F1W

Symptom or defect of the TV
It doesn't turn on, the red light comes on and nothing else.

Solution in Samsung - LE40C530F1W

To verify that the power supply/inverter is functioning correctly, disconnect the connector that goes to the mainboard and the display should
to light up and the source must have all the voltages. With this we see that the problem is in the main.
replace the BN94-02616K with the BN94-04175P which is equivalent and the TV will be repaired.

Fault resolved in LG M227VDP

Symptom or defect of the TV
SOLD IMAGE FOR A SECOND AND LOSES BACKLIGHT.
Solution in LG - M227VDP
After reviewing the inverter part and seeing that everything is normal, I check the panel lamps and detect that there is a failure in the
last from the bottom part, since I can't change it, I bridge the inverter output with a 39k resistor.
Ohms and resolved. There is a little shadow at the bottom but acceptable.

128
 260. Malfunction resolved in LG M1962DL

Symptom or defect of the TV

It doesn't turn on, the Standby light blinks without fully turning on.
Solution in LG - M1962DL
Check the secondary capacitors of the power supply (sometimes they also fail), and if they are okay, replace the
integrated NIKOS P2503NPG (Q302 of the power supply). The television turns on perfectly.

261. Fault resolved in Philips 42PFL5604/77

Symptom or defect of the TV
Nothing turns on.

Solution in Philips - 42PFL5604/77

The standby power supply doesn't work. R801, R825, FSQ510 were changed; all of this burns out because of C806 being undervalued.
the TV works perfectly...

129
 262. Breakdown resolved in LG 42PQ6000

Symptom or defect of the TV

The image appears reddish but only through the digital terrestrial television, the other inputs and the menu look fine.

Solution in LG - 42PQ6000
The fault is located in the EEPROM at position IC110. I remove it and erase it completely, then I put it back.
the TV starts up well and automatically reprograms the virgin memory. Now it works well even after
turn it off.

263. Malfunction fixed in lg 32ld550

Symptom or defect of the TV
Does not tune into any channel.
Solution for lg - 32ld550
Replace tuner EBL60721201 and the TV will be ready.

130
 Repair solved on Sony KDL-40P2530
Symptom or defect of the TV
It turns on and after a while it turns off and starts to blink. Sometimes it lasts longer and other times shorter.

Solution in Sony - KDL-40P2530

After reviewing the source, I see a similar fault where they say that the fuse of the inverter marked as F003.
varies in value. In my case, it offers a resistance of 25 ohms, so I replace it with a new one and the TV
it works perfectly.

131
 [Link] resolved in PHILIPS 42PFL5522D

Symptom or defect of the TV

The TV turns on but the screen doesn't light up.
Solution in PHILIPS - 42PFL5522D
The problem is with the inverter. It is thoroughly checked and the fuse marked as F1 is found.
open SMD format. This is replaced and the TV works well.

Fault resolved in PHILIPS 42PF5521D

Symptom or defect of the TV
The pilot light turns on and after a few seconds it starts to blink.

Solution in PHILIPS - 42PF5521D

In the power supply, there are several desiccated capacitors because when heated, the TV starts up fine.
All those seen in the third photo are replaced and the TV is repaired.

132
 267. Fault fixed in PHILIPS 37PF5522D
Symptom or defect of the TV
The screen lights up for a moment and then turns off again.

Solution in PHILIPS - 37PF5522D

The problem is in the inverter output, there is a burnt capacitor, the C322 of 33pF at 3KV. It is replaced by
a new one and the TV is completely repaired.

268. Fault resolved in Sony KDL32D2810

Symptom or defect of the TV
Shortly after it starts functioning, the image turns entirely reddish.
Solution in Sony - KDL32D2810
It is checked and it is seen that when moving the LVDS cable, the image returns to normal. I pull it out of the clip and see that it is damaged.

fitted. I take it out, put it back in, and the device works correctly.

269. Fault resolved in Sharp LC-42WD1E

TV symptom or defect
Does Not Turn On. Standby LED in Green

Solution in Sharp - LC-42WD1E

It has the Diodo D24 (SB3H100) in stock. It is a Schottky diode of 3Amp 100Volts.

133
 Fault resolved in LG 19LH2000

Symptom or defect of the TV

It doesn't turn on.

Solution in LG - 19LH2000
The power supply is checked and the 8-pin integrated circuit p2503npg is replaced and functioning.

Fault resolved in PHILIPS 32PF5531D

Symptom or defect of the TV

It turns on but there is no image, there is no backlight, there is sound.
Solution in PHILIPS - 32PF5531D
In the inverter, everything is checked and I find the black fuse F1 is blown. It is replaced with a new one of 1.6A and
The TV is working correctly.

134
 Fault resolved in LG 32LC56
Symptom or defect of the TV
It doesn't turn on, it doesn't do anything, only the Standby light is on.
Solution in LG - 32LC56
Several inflated capacitors are observed in the source, I replace all of them and the TV works.

Fault resolved in Philips 32PFL3017H

Symptom or defect of the TV
It doesn't turn on. The Standby light is on but nothing else.
Solution in Philips - 32PFL3017H
The power supply is checked when empty and the standby is canceled, in this way the power supply provides all the voltages so that
That's fine. I will replace the mainboard and the TV will be repaired.

Malfunction resolved in SAMSUNG PS42A418C10XXC

Symptom or defect of the TV
The image is shifted to the right, the TXT is not working, everything else is functioning correctly.
Solution in SAMSUNG - PS42A418C10XXC
We enter the service menu and in the Item. We do a Reset on Eproom and it works correctly again.

275. Fault resolved in Samsung LE32S60BD

Symptom or defect of the TV
It turns on and you can hear it, but the screen does not light up.

Solution in Samsung - LE32S60BD

The inverter is disassembled and it is checked with the multimeter that the fuse F3 is blown. It is replaced with one.
new in plastic format and the TV works correctly.

276. Malfunction solved in LG 32LC2DB

Symptom or defect of the TV
It doesn't turn on.

Solution in LG - 32LC2DB
135
I have seen other similar breakdowns about the capacitors and I went straight to the source. Indeed, in this case
The capacitors are swollen. I replaced all of them and the TV has worked properly.

277. Issue resolved in Toshiba 22DV734G

Symptom or defect of the TV

It lights up but after a few seconds it loses the backlight.
Solution on Toshiba - 22DV734G
El problema está en el transformador del inverter que tiene uno de los secundarios abiertos. Busco el
original transformer TMS94481 but I can't find it so I will use a TMS91429 like the ones that are mounted
Samsung and the TV work perfectly.

278. Malfunction fixed in Samsung LE19R71B

Symptom or defect of the TV
It doesn't turn on.

Solution in Samsung - LE19R71B

The fault is in the power supply, a swollen capacitor is observed. All secondary ones and the TV are replaced.
it is repaired.

136
 Fault resolved in Philips 42PFL5522D/12
Symptom or defect of the TV
The TV turns on and there is sound but no image.

Solution in Philips - 42PFL5522D/12

It is observed that the fault comes from the inverters. All fuses are measured and one is found to be open.
replace this fuse and the TV will be repaired.

280. Issue resolved in Samsung LE40A536T1F

Symptom or defect of the TV
All white screen, with sound.
Solution in Samsung - LE40A536T1F
I suspected the panel, but we took the risk of changing the AS19 integrated circuit on the T-CON, this integrated circuit is a bit
hard to remove, since to dissipate heat there is solder at the center of the chip underneath, it was changed and
it worked correctly.

Fault resolved in LG 42PC1D

Symptom or defect of the TV
It doesn't turn on, it does nothing.

Solution in LG - 42PC1D
In the power supply, I locate some swollen capacitors, I replace them, and the TV turns on perfectly.
Almost all need to be changed, as most are inflated.

Fault repaired in Philips 42PFL7662D

Symptom or defect of the TV
Intermittent red light when you try to turn it on.
Solution in Philips - 42PFL7662D
If you suspect the power supply, the 450V filter capacitor is replaced but the TV continues to malfunction.
It was decided to replace the entire power supply with ref. PLCD300P3 and the TV is now repaired, it works well.

283. Malfunction resolved in Samsung LE26A457C1D

Symptom or defect of the TV
Sometimes it doesn't turn on and other times it turns off.

Solution in Samsung - LE26A457C1D

After checking the source I realize that hitting the source turns off the TV. I check the solder joints and
I locate a solder joint in the transistor seen in the third photo. Once re-soldered, the TV works.
correctly.

Fault fixed in LG 42LE7500

Symptom or defect of the TV
He has lost all channels. You do an automatic search but it doesn't find any channels.
Solution in LG - 42LE7500
The tuner with ref. EBL60740404 is replaced on the motherboard and another channel scan is performed.
automatic and now it finds channels, so the TV is considered repaired.
137
 285. Fault fixed in Philips 32PFL5522D
Symptom or defect of the TV
It doesn't turn on, it doesn't do anything. The Standby LED is off.

Solution in Philips - 32PFL5522D

The standby source voltage is measured, which should be 5V, and there is nothing. The control integrated circuit is replaced.
NCP1207 but it still does not provide voltage. The 431 regulator at the output of the power supply is measured and it shows a short between two of

its legs. It is replaced by a 431K also in SMD format and the TV works correctly. It is seen in the third
photo.

Fault fixed in Samsung LE37C530F1

Symptom or defect of the TV
When connecting the LCD to the electrical power, the red LED blinks five times and then turns off, the LCD does not turn on. Any
Sometimes when you connect the LCD, it turns on perfectly, but if you turn it off again, it doesn't turn on anymore.

Solution on samsung - LE37C530F1

The power supply voltages are checked and it can be seen that they are all correct. There is suspicion of
the main board. The main board BN94-02616U is replaced by BN94-041175L, which are the same and the fault is resolved.
resolved.

138
 287. Damage resolved in Samsung LE32R32B

Symptom or defect of the TV

Colored lines are seen and the rest in black with backlighting turned on.

Solution in Samsung - LE32R32B

The problem seems to be the display but the fault is in the T-CON. I measure at the output of the regulator that can be seen in the
third photo where there should be 2.5V and there is only 1.2V. I replace the regulator with one of 2.5V and the TV works
perfectly.

139
 288. Breakdown resolved in Viewsonic N2360W
Symptom or defect of the TV
The TV does not turn on.

Solution in Viewsonic - N2360W

The problem lies in the power supply. I suspect the IC2 circuit and replaced it but the power supply still does not work.
It works. I measure the ZD4 diode and it is shorted. I put in a 15V zener and the power supply works again.

Fault resolved in LG 19LS35000

Symptom or defect of the TV
It won't turn on, the LED doesn't light up at all.

Solution in LG - 19LS35000
On the motherboard next to the power connector, there is a fuse that is blown. I replace it with one of
3.15A and the TV works perfectly.

140
 Fault resolved in Panasonic TX-32LXD65F

Symptom or defect of the TV

The TV does not turn on. The indicator light comes on and the relays make noise but nothing else.

Solution in Panasonic - TX-32LXD65F

I observe that when heating the source, the TV eventually turns on. After replacing the electrolytic capacitors, the
The TV keeps failing. In the end, I detect that the polyester capacitors seen in the photo are yellow.
They are incapacitated. The yellows are the new ones, the old ones were black but I don't remember the value.
The five disabled were there, once they were set up the TV works well.

Fault resolved on LG 42LD750

Symptom or defect of the TV
The TV won't turn on, it doesn't do anything.

Solution in LG - 42LD750
I check the power supply and observe that there is a blown fuse. I measure the transistors that are seen in the photo and one of them
They are short. I put in a P8NA60 and the TV works well.

141
 Malfunction resolved in LG 42LC2D
Symptom or defect of the TV
It normally doesn't turn on, and when it does, it takes a long time.

Solution in LG - 42LC2D
The fault is in the power supply. I fixed it by changing all the electrolytics, once.
changed the TV works on the first try.

Fault fixed on LG 50PQ2000

Symptom or defect of the TV
When you plug it in, the light comes on but it does not exit Standby.

Solution in LG - 50PQ2000
The power supply is checked and it is observed that it provides all the voltages when we disconnect the connector from the
Mainboard. It is decided to replace the mainboard EBT60771521 and the TV is repaired.

[Link] resolved in Samsung LE27S73BDX/XEC

Symptom or defect of the TV
There is no image, only several vertical stripes of colors appear, there is sound and backlighting.

Solution in Samsung - LE27S73BDX/XEC

The fault is located in the tcom module. The capacitor cp24 and the ic UP4 were replaced.

[Link] resolved in Samsung LE32R32B

Symptom or defect of the TV
It lights up for a moment and goes dark again, the sound continues well.
Solution in Samsung - LE32R32B
The problem is with the inverter, I measure the transformers and I don't see any open. I decide to replace the inverter.
complete with ref. VK89144J04. Once the TV is set up, it works properly.

142
 Fault resolved in LG 32LH3000
Symptom or defect of the TV
The TV doesn't work, it doesn't do anything, the power LED doesn't light up.

Solution in LG - 32LH3000
Measuring, I see that the main input fuse is blown. The cause of this blown fuse is due to a surge of
light that has at the same time blown the network filters from 400V to 82uF. The two capacitors and the fuse are replaced.
the TV is working perfectly.

297. Fault resolved in Sony KDL-40P3600

The TV doesn't turn on, it doesn't do anything.

Solution for Sony - KDL-40P3600

143
A low-value resistor is located open in the primary of the power supply. I put it in place.
8.2 Ohms and it works perfectly.

298. Fault resolved in LG 50PJ350

Symptom or defect of the TV
Does not turn on, Relay Click... Click

Solution in LG - 50PJ350
One of the 22 Ohm resistors is open. I replaced only one, and after three months the other one failed. Better to replace them both.
both at the same time. R929 and R927.

[Link] resolved in JVC LT-30E45SU

Symptom or defect of the TV
When you turn on the TV, the picture appears for a second and then disappears, the sound continues fine.

Solution in JVC - LT-30E45SU

The problem lies in the inverter that is not functioning correctly. By measuring the transformers, I locate
one that measures open between the output ends. The transformer with ref. 4009A is replaced and the TV remains
repaired.
144
 [Link] resolved in LG 42LG3000

Symptom or defect of the TV

The solarized image looks very bad.

Solution in LG - 42LG3000
On the T-CON board, the AS15F is replaced by an AS15G and the TV works correctly.

[Link]

[Link] resolved in Samsung LW15M23CP

Symptom or defect of the TV
There is no image through any external input. If we have an image through the tuner (analog, not
has TDT)
Solution in Samsung - LW15M23CP
Enter service mode: POWER OFF, DISPLAY, MENU, MUTE, POWER ON. Activate RESET. Ready.

302. Malfunction resolved in LG [Link]

Symptom or defect of the TV
The digital terrestrial television (DTT) is not working and makes some noise when starting up.

Solution in LG - [Link]
Replace all the filters in the power supply.

145
 303. Fault resolved in Philips 26PF3320
Symptom or defect of the TV
The screen does not light up. The sound is correct.

Solution in Philips - 26PF3320

The problem is the inverter that is not working correctly. It is disassembled and it is observed that some
transistors are overheated and shorted. It is decided to replace the complete inverter with ref. CIU11-T0040 and the
TV is completely repaired.

304. Breakdown resolved in Philips 47PFL8404H

Symptom or defect of the TV
It lights up for a moment and then goes dark again. The sound is perfect.

Solution in Philips - 47PFL8404H

The power supply / inverter is being checked, since I suppose the problem is with the inverter. I believe the problem is the
high voltage output transformer and since I can't find it anywhere I take it from a 42 power supply
inches. Physically, the transformers are the same; once the transformer is installed, the TV works.
correctly.

305. Breakdown solved in Philips 37PFL5603D

Symptom or defect of the TV
When turned on, the green LED lights up, a click from the relay is heard, and it does not work.
Solution on Philips - 37PFL5603D
Change the three SMD resistors on the power supply board in positions R-328/329/330 of 1 megaohm.
They are next to the IC-601. I have put 3 resistors of 1 mega of 1/2w and it works.

146
 306. Fault resolved in Sony KDL-32S2020

Symptom or defect of the TV

It turns on but does not have backlighting.

Solution for Sony - KDL-32S2020

The inverter is disassembled and it is checked that one of the fuses is blown, it is F001. Once the fuse is put in.
At 3.15A the TV works correctly.

307. Fault resolved in Samsung LE40A455C1D

Symptom or defect of the TV
Backlight blinks in cold. It turns off after half an hour.

Solution in Samsung - LE40A455C1D

I check the voltage in cond. CP802. There is only 340V, it should have 390V. I see that the ICP802 is not powered.
The plate 6. I put a 100 ohm resistor between the Collector and Emitter of the Transistor QM803. And that's it.

308. Fault resolved in LG 42PC1RR

Symptom or defect of the TV
You turn on the TV and the sound appears but not the image.

147
Solution in LG - 42PC1RR
The problem is in the Y-SUS board, I measure the fuse and it is open. I change the Y-SUS board with ref.
EBR31564801 and the TV is repaired.

Fault resolved in Philips 37PFL5603D

Symptom or defect of the TV

The image looks bad, it's like solarized.
Solution on Philips - 37PFL5603D
It is a typical fault of the T-CON board; the AS15F chip is replaced and the TV is repaired.

[Link] resolved on LG 37LF75

Symptom or defect of the TV

One can hear it but can't see anything.

Solution in LG - 37LF75
On the inverter board, the 2 capacitors 35v 680uf are swollen and open. They are replaced and it works.

148
 311. Fault resolved in Philips 32PFL5604H/12

Symptom or defect of the TV

It can be heard but not seen.

Solution in Philips - 32PFL5604H/12

I dismantle the inverter board, inspect it and see that one of the solder joints is bad (EL34) the solder joints are redone and
to work.

Fault fixed in LG 37LC45

Symptom or defect of the TV
When it has been running for a while, the image starts to appear with green tears and horizontal stripes.
through the top.

Solution in LG - 37LC45

149
It is checked that applying cold to an area of the mainboard improves the image. I end up changing the
capacitors seen in the third photo. The originals are in SMD format but I am using standard ones and the TV
it is perfectly repaired.

313. Malfunction resolved in LG M227WDP

Symptom or defect of the TV
Once the power switch was turned on, an image appeared on the screen with sound and lasted for a second.
then I let the image go out and only the channel information appeared.
Solution in LG - M227WDP
I tried the lamps and one of them didn't turn on, so I disabled the lamp that was failing.
a scanner lamp in place of this, placing it inside the TV casing next to the
connectors of the lamps with a support adapted for lamps, the same as the one I had on the scanner, fixing
This is at the back of the display; its arrangement is vertical. The television remains repaired, not
the absence of the burnt-out lamp is appreciated, thus saving me a cost and opening the display to replace one
of the two upper lamps of the backlighting.

[Link] resolved in LG 42LG300

Symptom or defect of the TV

The image appears dark and solarized. Sometimes it improves and other times it worsens.
Solution in LG - 42LG300
The solution is to change the AS15G integrated circuit on the display's T-CON board. It is an SMD format integrated circuit.
Once replaced with a new one, the TV looks perfect.

315. Issue resolved in Samsung

Symptom or defect of the TV
When turned on, without sound and without image, a small flash can be seen on the display.
Solution in Samsung - LE32A336J1NXXC
In my case, the cause is the two diodes dm853 and dm851 that have bad soldering, specifically dm851 was ...
completely desoldered.

150
 316. Breakdown resolved in Toshiba 32DT1U
Symptom or defect of the TV
The function buttons on the TV are not responding, as the customer said that the TV got wet.
Solution on Toshiba - 32DT1U
Replacing all the micro switches solved the problem.

Fault resolved in LG TA2280

Symptom or defect of the TV

It has suffered a fall and the image is not visible, the sound is fine.
Solution in LG - TA2280
This is an LED TV, when I open it I see that the connector that powers the LED diodes of the screen is loose, I connect it.
I press it firmly and the TV works perfectly.

Fault resolved in LG RZ-42PX11

Symptom or defect of the TV
You can hear it but you can't see it.

151
Solution in LG - RZ-42PX11
I found a blown fuse in the Y-SUS, so I have to replace it since there is a short circuit in the VS line.
The Y-SUS with reference 6871QYH029R is replaced and the TV is repaired.

319. Fault solved in Samsung LE32T51B

Symptom or defect of the TV

The image lights up for a moment and disappears, the sound continues.
Solution in Samsung - LE32T51B
In the inverter, I measure the transformers and locate one that is open. Its reference is 4002P, I replace it.
for a new one and the TV works correctly.

[Link] resolved in Samsung LE37C550

Symptom or defect of the TV
When it has been running for a while, it turns off and after a while, it turns back on by itself.
152
Solution on Samsung - LE37C550
The problem lies in the power supply that starts to fail when it heats up. It is sprayed with snow.
liquid but I can't see which component is the one that fails. In the end, I end up changing the power supply.
complete. The reference for this is BN44-00339B. The TV works correctly with the new power supply.

Fault resolved in PHILIPS 37PFL7762D

Symptom or defect of the TV
Philips TV with solarized image, dark spots, as if the LCD panel or LVDS cable is faulty.

Solution in PHILIPS - 37PFL7762D

Everything seems to be a failure in the T-CON, the AS15G integrated circuit. We changed the entire T-con and the problem persists.
We checked the inverter and it has a blown fuse, we replaced it along with the capacitor and the fault was fixed.
solve.

153
 Fault resolved in Panasonic TX-L37S20E
Symptom or defect of the TV
It turns on but does not light up the screen.

Solution in Panasonic - TX-L37S20E

I believe the inverter circuitry that goes on the same board as the power supply is faulty. The board has the reference
N0AC3GJ00016, the complete board is replaced and the TV is repaired.

323. Malfunction fixed in Samsung LE32B530P7W

Symptom or defect of the TV
The screen lights up for a moment and then darkens again.
Solution in Samsung - LE32B530P7W
The fault is in the power board/inverter with reference BN44-00261A. The entire power supply is replaced and the TV.
it is perfectly repaired.

324. Breakdown fixed in Sharp LC-32SHe-bk

Symptom or defect of the TV
It doesn't turn on, not even the Standby light.

Sharp solution - LC-32SHe-bk

154
The open fuse and the blown integrated circuit TNY277PN are checked at the source. Both are replaced and
the TV is repaired.

[Link] resolved in ACER AT4220

Symptom or defect of the TV
You turn on the TV and it lights up for a moment and then the picture goes off again.

Solution in ACER - AT4220

The fault is in the inverter, the fuses and transformers are checked and nothing is observed.
Irregular. The inverter VIT7101051 is replaced, and the TV is repaired and looks perfect.

[Link] resolved in LG 37LH4000

Symptom or defect of the TV
The TV doesn't turn on at all, not even the Standby light.

Solution in LG - 37LH4000
It is observed that the fuse is open and one of the transistors in the third photo is short-circuited. It is decided
replace the complete source EAY57681001 to avoid problems.

327. Breakdown resolved in SONY KDL40W5500

Symptom or defect of the TV

155
TOTALLY DEAD, THE LED DOES NOT TURN ON.

Solution in SONY - KDL40W5500

The fault is due to the absence of stand-by voltage. Exchange diodes D6204 and D6203 for two BA157, located at
side of the IC MIPO2H2.

328. Breakdown solved in LG 37LD450

Symptom or defect of the TV
The TV turns on but does not tune into the channels. Two searches have been conducted and it has not tuned into anything.

Solution in LG - 37LD450
Enter the Service Menu and perform a Reset, but the TV continues to fail. The tuner is tested for replacement.
Then the TV is working correctly. The tuner reference is TDTJ-S0001D.

329. Issue resolved in SHARP LC-37AD5E-BK

Symptom or defect of the TV
The TV doesn't turn on. The LED turns green and after a moment it goes back to red, flashing.

Solution in SHARP - LC-37AD5E-BK

Tensions are checked and they're fine. It does nothing when trying to enter service mode. There are suspicions about the inverter.
and they are disconnecting lamps and placing a 47k / 10w resistor in its place until I figure out the
defective and it is possible to enter service mode to delete the accumulated errors (in Sharp when accumulating 5.
errors the TV does not turn on). Once this is done, the TV turns on, the lamp is replaced, and it is repaired.

330. Fault resolved in Daewoo DLT-32C3FTB

Symptom or defect of the TV
It doesn't turn on, the indicator light comes on and nothing else happens.

Solution in Daewoo - DLT-32C3FTB

In the power supply, I found a couple of swollen capacitors. I change all of those in the secondary and the
TV is repaired.
156
 [Link] resolved in Samsung UE32C4000
Symptom or defect of the TV
The TV turns on and you can hear it, but there is no picture.

Solution in Samsung - UE32C4000

It is determined that the problem is that the inverter power supply does not work because it does not output voltage to feed the
LED of the screen. The new power supply BN44-00349B is placed but the TV continues to fail. Measuring the
BL_on tension coming from the main is observed to always be zero volts. 5V is injected and the screen
brightens. When removing the 5V, it must be that the BL_on output is unlocked and it always works well. When you switch to
Standby drops to 0 volts and when you turn it on, it rises to 5V, so I consider the TV repaired after a few days.
functioning well.

Repair resolved on LG 32LG3000

Symptom or defect of the TV
The colors look wrong, as if they are changed. Besides, it looks very dark.

Solution in LG - 32LG3000
The T-CON board is disassembled and it is observed that it has the AS15-G circuit. This is replaced with a new one and the TV
it works perfectly.

157
 333. Issue resolved in Toshiba 32el833g

Symptom or defect of the TV

It turns on normally but has a stripe in the image. It has gotten wet.

Solution in Toshiba - 32el833g

It is the second LED LCD I find with the TCON at the bottom and also the connectors that go to the panel. The
The thing is that if they get wet, as in this case, the plate that connects the panel gets ruined. I have been able to repair it.
making the tracks with very thin wires, as they had lost continuity.

158
 334. Fault resolved in LG 32LC2DB
Symptom or defect of the TV
It doesn't turn on, the indicator lights up but nothing else.

Solution in LG - 32LC2DB
In the power supply, two swollen capacitors can be seen. These are replaced, and the TV works. The best thing is
Change all the capacitors in the power supply to avoid future problems that may arise.

[Link] resolved in LG 42LH3000

Symptom or defect of the TV

The screen media is not visible or appears with stripes.

Solution in LG - 42LH3000
It is observed that the display is failing because sometimes when touching the screen it works fine. Everything is taken apart.
The panel shows that one of the connection flexes is not making proper contact; when you put your finger on it, it gets fixed.
A rubber is placed to apply constant pressure and it is repaired.

159
 336. Issue resolved in Samsung

Symptom or defect of the TV

When it has been running for a while and gets quite hot, it turns off.
Solution in Samsung -
I don't remember the Samsung model, I'm uploading a couple of photos. The problem is when it overheats, that's why I...
I apply heat to the mainboard and I detect that when I heat the integrated circuit marked in red in the second
photo, the TV turns off. I replace this integrated with ref. AOZ1021HAIL and the TV does not fail again.

337. Fault resolved in LG 42LG6000

Symptom or defect of the TV
Stripes appear in the middle of the image like interferences.

Solution in LG - 42LG6000
I apply heat to the plate located in the center of the screen and it seems to improve. Depending on where I apply the
Heat improves more or less. I start by changing capacitors in the area where I heat and it gets fixed faster. To

160
I'm finally finishing by changing the capacitors that are seen in image 3 and how I put normal capacitors.
I have to cut the metal protection to be able to close it. The TV works perfectly.

338. Fault resolved in Philips 37PFL5603D

Symptom or defect of the TV

It turns on but the central part of the screen is dark and the rest of the image is blinking.
Solution in Philips - 37PFL5603D
The power supply is checked and after many measurements it is observed that the filter capacitor of
180uF at 450V is completely dry although nothing unusual is physically noticeable. It is replaced and the TV works.
well.

339. Issue resolved in Sony KDL-19BX200

Symptom or defect of the TV
It doesn't turn on, it doesn't do anything.

Solution for Sony - KDL-19BX200

161
The source is checked and I find the diode D2031 shorted. It is replaced by a BYW95C and the TV works.
perfectly.

340. Breakdown solved in Samsung

Symptom or defect of the TV

It turns on but the screen does not light up.

Solution on Samsung -
Measuring at the inverter, I check that the inverter transformer has an open output. The problem is that
this TM-09180 transformer is no longer available. So what I do is place the transformer
TMS91429CT adjusting the holes in the plate so that it fits well and the TV works perfectly.

341. Malfunction resolved in LG W1942T

Symptom or defect of the TV
It doesn't turn on, it doesn't do anything. The pilot light blinks several times and then goes off again.

Solution in LG - W1942T
In the power supply, there are several swollen 1000uF and 470uF capacitors. They are all replaced and the TV works.
perfectly.
162
 342. Fault resolved in Samsung LE32S60BD
Symptom or defect of the TV
The TV works fine but the sound always comes out at maximum volume and when you try to turn it down a kind of code appears.
bars.

Solution in Samsung - LE32S60BD

You need to enter the service menu by pressing Off-info-menu-mute-on and then make a complete reservation. Now it has
The volume defect has disappeared but it doesn't tune into channel 69, when it reaches 68 it stops. Now we need to
make a Plug And Play to be able to fully adjust the configuration and the problem is solved.

343. Fault resolved in Philips 47PFL7603D

Symptom or defect of the TV
It works but after a few seconds it loses the image. Sometimes it is fine for a few minutes and then it loses it.
image.
Solution in Philips - 47PFL7603D
The power supply and the inverter are checked, and I find that there are some cold solder joints on the transformer.
from the inverter output. I resolve everything well and the TV works perfectly.

163
 [Link] resolved in Lg 42lv5500

Symptom or defect of the TV

The TV turns on with backlighting and seems to respond to the remote control, sound is heard, but it is not visible.
no image.
Solution in Lg - 42lv5500
The power supply voltages are checked and everything is okay. On the t-con, there is an IC that gets very hot, it is measured in the
The output from this circuit is true and there is a short. Disconnecting the flex cables that go to the screen, I see that the short disappears.
I dismantle the panel and observe corrosion; apparently, it has gotten wet. I find on the board that goes to the LCD screen a
shorted capacitor, it is replaced and there is already an image, but it looks bad, 6 resistors nearby are measured and
They are found open, are replaced, and the TV is fine.

345. Malfunction resolved in LG RZ-26LZ55

Symptom or defect of the TV

The screen lights up for a moment and the image disappears.
Solution in LG - RZ-26LZ55
I measure in the inverter the transformers and locate one of them that is open. The open transformer is the
reference 4004D, I change it and the TV works normally again.

164
 Fault resolved in SAMSUNG LE-40S73BD
Symptom or defect of the TV
The TV continuously switches between inputs (PC-HDMI-TV). Sound and image are fine.
Solution in SAMSUNG - LE-40S73BD
The Stamby micro button with internal resistance. Changed and resolved.

Fault fixed on Philip 42PFL7762D/12

Symptom or defect of the TV
Does not turn on. Standby LED off

Solution in Philip - 42PFL7762D/12

I am going to check the 5v of stby. And I see from the back of the board that the IC 'U400' is blown. I know it is
a TEA1533AT. I replace it and also the R409 "8.2K", but it still doesn't turn on. I realize that the IC is not receiving
18V power supply to pin 2. I continue checking and I find the T402 '3FW' shorted. The transistor I
I replaced it with a normal one "BC557".

165
 Fault resolved in Samsung 933HD

Symptom or defect of the TV

Se cambia de canal sola y se sube y se baja el volumen. También sale el menu cuando quiere.

Solution in Samsung - 933HD

The local button panel seems to be faulty. The button panel disconnects and the TV stops doing weird things. In the end, it
Replace the entire button panel as I can't find the buttons anywhere. The TV is repaired.

[Link] resolved in ZENITH

Symptom or defect of the TV

It turned on immediately with a white screen, no sound or image.

Solution in ZENITH -
The power supply was checked for its voltages and the B+ of 5 volts was elevated to 8 volts, so we proceeded to check the
regulator, being this open and short, we proceeded to look for a suitable one being a p-channel mosfet and
checking only the power supply it was seen that it regulated its normal 5 volts that it should have and it was proceeded to connect
complete the source by turning on the device normally with image and sound, now taking time to turn on the
backlight until the channels and image entered solving the problem.

166
 350. Breakdown resolved in LG 26LC2R

Symptom or defect of the TV

Comment

0 MAN_REPAR

The TV was slow to turn on and the capacitors were replaced and it worked well. Now the problem is that it does not
the HDMI input works.

Solution in LG - 26LC2R

After many checks, I realize that the IC1008 regulator should have an output of
3V3 only supplies 1V9 which is not enough. I measure with the oscilloscope at the input and it has
Much distortion in the 5V coming from the power supply. The problem lies in the capacitor C210 of 680uF.
Power supply that is disabled. Once the voltage is changed, it rises to 3V3 and the HDMI works well.

167
 Fault resolved in Samsung LE32B450
Symptom or defect of the TV
The TV works but it turns off and on, changes channels, does strange things.

Solution in Samsung - LE32B450

Reviewing everything, I realize that the button panel is not working very well, I disconnect it and then the TV never fails.
I finally replaced the entire control panel with ref. BN41-00989A and the TV is repaired.

Fault repaired in Philips 37PFL8404H

168
Symptom or defect of the TV
The screen does not light up, it does nothing.

Solution in Philips - 37PFL8404H

In the inverter, I see that it has some very black capacitors that should be blue. There is one of them.
from 47pF to 2000V that is burned, I decide to replace both on the board since the other one is also a
little black. Once the new capacitors are in place, the TV works well.

169
 Fault resolved in Samsung LE26A336J1D

Symptom or defect of the TV

Sometimes the image looks bad and other times it looks good.
Solution in Samsung - LE26A336J1D
In the T-CON I notice that touching the connection flex with the panel makes the image go right or wrong. I dismantle the flex.
I cleaned all the contacts well with cleaner spray and it seems that it won't fail again.

354. Fault resolved in Philips 37PFL8404H

Symptom or defect of the TV

The image looks bad, like solarized, with a predominance of blue.
Solution in Philips - 37PFL8404H
I check the T-CON and notice that the AS15F integrated circuit gets very hot. I replace the AS15F circuit and the TV
it is completely repaired, it looks perfect.
[Link] page 45

170
171
172
173
174
.

175
176
177