Scribd
Upload
2K views10 pages

Fleck 5600SXT Programming Guide

This document provides programming instructions for a water softener or iron filter control valve model 5600 SXT. It includes directions for setting the time of day, regeneration time, reserve capacity, and other user and master programming settings. The diagnostic section allows viewing current and peak flow rates, hours in service, volume used, and other diagnostic data.

Uploaded by

RainPure
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views10 pages

Fleck 5600SXT Programming Guide

This document provides programming instructions for a water softener or iron filter control valve model 5600 SXT. It includes directions for setting the time of day, regeneration time, reserve capacity, and other user and master programming settings. The diagnostic section allows viewing current and peak flow rates, hours in service, volume used, and other diagnostic data.

Uploaded by

RainPure
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

8/7/08 SOFTENERS AND IRON FILTERS Model 5600 SXT-User Programming Chart Time of Day

FROM SERVICE MODE: To set Time of the Day push and hold (*Not both Up and Down Buttons) Display is TD (Time of Display) Press display time.

UP

or

DOWN

button for 5 seconds

UP

or

DOWN

button to adjust the

Press Extra Cycle button to resume normal operation

Model 5600 SXT -User Programming Chart


FROM SERVICE MODE: To set user programming push and hold

UP

and

DOWN

buttons for 5

seconds, and the time of day is NOT set to 12:01 PM. Display is DO (DAY OVERRIDE) [factory default setting: OFF]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RT (REGENRATION TIME) ([default: For Iron Filters - 11:00 P.M. For Softeners 2:00 A.M.] Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is H (FEED WATER HARNESS) [grains per gallons default: Softeners - 15]. Iron content ppm per gallon default: Iron Filters - 20 Press UP/DOWN buttons to adjust the value. NOT AVAILABLE IF THE VALVE TYPE IS SET TO FILTER IN MASTER PROGRAAMING.
Extra Cycle Button

Display is RC (FIXED RESERVE CAPACITY) [Fixed reserve capacity in gallons default: 0]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

42133

Display is CD (CURRENT DAY OF THE WEEK). Press UP/DOWN buttons to adjust the current day of the week. ONLY AVAILABLE IF DAY OF THE WEEK CONTROL IS ON IN MASTER PROGRAAMING

Model 5600 SXT- Master Programming Chart


FROM SERVICE MODE:-

To enter master programming mode, set the Time of Day display to 12:01 P.M.

Extra Cycle Button

Press and hold

UP

and

DOWN

buttons together until the programming icon

replaces the service icon Display is DF (DISPLAY FORMAT) Unit of measure for volume and display format for time [Factory Default Setting: GAL]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is VT (VALVE TYPE) type of valve setting [Factory Setting: St1b (Standard Downflow/Upflow, Single Backwash]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is CT (Control Type) type of regeneration [Factory Setting: Fd (Meter Delayed)]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is NT (Number of Tanks) [Factory Default Setting: 1]. Do not change the setting.
Extra Cycle Button

Display is UNIT CAPACITY Capacity in grains for softeners and in ppm per gallon for iron filters. [Factory Default Setting: Refer to User Manual].

Press UP/DOWN buttons to adjust the value.


Extra Cycle Button

Display is H (WATER HARDNESS) Grains per Gallon for softener and ppm per gallon of iron for iron filters will appear [factory default setting grains per gallons for Softeners 15gpg Iron content in ppm per gallon for Iron Filters 20ppm]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

Display is RS (RESERVE SELECTION) Type of reserve [Factory Default Setting: RC (Fixed Reserve Capacity)]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RC (FIXED RESERVE CAPACITY) Reserve capacity in gallons [Factory Default Setting: 0]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

Display is DO (DAY OVERRIDE) [factory default setting: OFF]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RT (REGENRATION TIME) ([default: For Iron Filters 11:00 P.M. For Softeners 2:00 A.M.] Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is BW (BACKWASH) [Factory Setting: For Iron Filter and Softener10 (10 minutes) For Chemical Free Iron Filters 6 (6 minutes) ]. Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is BR (BRINE RINSE) [Factory Setting: For Chemical Free Iron Filters 0 (0 minutes) For Iron Filters 50 (50 minutes) For Softeners 60 (60 minutes)] Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is RR (RAPID RINSE) [Factory Setting: For Softeners and Iron Filters - 10 (10 minutes) For Chemical Free Iron Filters 4 (4 minutes) ]. Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is BF (BRINE FILL) [Factory default setting: Refer to User Manual]. Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is D (DAY OF WEEK) used to set the day of week in which the regeneration should occur [Factory Setting: OFF]. Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING.
Extra Cycle Button

Display is CD (CURRENT DAY) used to set the current day of week in which the regeneration should occur Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING.
Extra Cycle Button

Display is FM (FLOW METER TYPE) [Factory Setting: t0.7].Do not change this setting.
Extra Cycle Button

RETURN TO SERVICE

Model 5600 SXT-Diagnostics Chart


To enter the diagnostic mode, push and hold

UP

and

Extra Cycle Button

button for 5 seconds.

Display is FR (CURRENT FLOW RATE) display current flow rate in gallons per minutes.

UP
Display is PF (PEAK FLOW RATE) display peak flow rate in gallons per unit since the last regeneration cycle.

UP
Display is HR (HOURS IN SERVICE) display to view the hours in service since the last regeneration cycle.

UP
Display is VU (VOLUME USED) display the volume in gallons used since the last regeneration cycle.

UP
Display is RC (RESERVE CAPACITY)display the reserve capacity in gallons.

UP
Display is SV (SOFTWARE VERSION)display the software version
Extra Cycle Button

End of Diagnostics

8/7/08 FILTERS Model 5600 SXT-User Programming Chart Time of Day


FROM SERVICE MODE: To set Time of the Day push and hold (*Not both Up and Down Buttons) Display is TD (Time of Display) Press display time.

UP UP

or

DOWN DOWN

button for 5 seconds

or

button to adjust the

Press Extra Cycle button to resume normal operation

Model 5600 SXT -User Programming Chart


FROM SERVICE MODE: To set user programming push and hold

UP

and

DOWN

buttons for 5

seconds, and the time of day is NOT set to 12:01 PM. Display is DO (DAY OVERRIDE) [factory default setting: OFF]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RT (REGENRATION TIME) ([default: 11:00 P.M.]. Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is RC (FIXED RESERVE CAPACITY) [Fixed reserve capacity in gallons default: 0]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

Display is CD (CURRENT DAY OF THE WEEK). Press UP/DOWN buttons to adjust the current day of the week. ONLY AVAILABLE IF DAY OF THE WEEK CONTROL IS ON IN MASTER PROGRAAMING

Model 5600 SXT- Master Programming Chart


FROM SERVICE MODE:-

To enter master programming mode, set the Time of Day display to 12:01 P.M.

Extra Cycle Button

Press and hold

UP

and

DOWN

buttons together until the programming icon

replaces the service icon Display is DF (DISPLAY FORMAT) Unit of measure for volume and display format for time [Factory Default Setting: GAL]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is VT (VALVE TYPE) type of valve setting [Factory Setting: Fltr (Filter)]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is CT (Control Type) type of regeneration [Factory Setting: Fd (Meter Delayed)]. Press UP/DOWN buttons to adjust the settings.
Extra Cycle Button

Display is NT (Number of Tanks) [Factory Default Setting: 1]. Do not change the setting.
Extra Cycle Button

Display is UNIT CAPACITY Capacity in gallons. [Factory Default Setting: 10000 gallons] ]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

Display is RS (RESERVE SELECTION) Type of reserve [Factory Default Setting: RC (Fixed Reserve Capacity)]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RC (FIXED RESERVE CAPACITY) Reserve capacity in gallons [Factory Default Setting: 0]. Press UP/DOWN buttons to adjust the value.
Extra Cycle Button

Display is DO (DAY OVERRIDE) [factory default setting: OFF]. Press UP/DOWN buttons to adjust the setting.
Extra Cycle Button

Display is RT (REGENRATION TIME) ([default: 11:00 P.M.] Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is BW (BACKWASH) [Factory Setting: 6 (6 minutes)]. Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is BD (BRINE DRAW) [Factory Setting: 0 (0 minutes) Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is RR (RAPID RINSE) [Factory Setting: 4 (4 minutes)]. Press UP/DOWN buttons to adjust the time.] Press UP/DOWN buttons to adjust the time.
Extra Cycle Button

Display is D (DAY OF WEEK) used to set the day of week in which the regeneration should occur [Factory Setting: OFF]. Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING.
Extra Cycle Button

Display is CD (CURRENT DAY) used to set the current day of week in which the regeneration should occur Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING.
Extra Cycle Button

Display is FM (FLOW METER TYPE) [Factory Setting: t0.7].Do not change this setting.
Extra Cycle Button

RETURN TO SERVICE

Model 5600 SXT-Diagnostics Chart


To enter the diagnostic mode, push and hold

UP

and Extra Cycle


Button

button for 5 seconds.

Display is FR (CURRENT FLOW RATE) display current flow rate in gallons per minutes.

UP
Display is PF (PEAK FLOW RATE) display peak flow rate in gallons per unit since the last regeneration cycle.

UP
Display is HR (HOURS IN SERVICE) display to view the hours in service since the last regeneration cycle.

UP
Display is VU (VOLUME USED) display the volume in gallons used since the last regeneration cycle.

UP

Display is RC (RESERVE CAPACITY)display the reserve capacity in gallons.

UP
Display is SV (SOFTWARE VERSION)display the software version
Extra Cycle Button

End of Diagnostics

You might also like