nRF52832/52840怎么将NFC引脚配置成通用IO（P0.09,P0.10）

最新推荐文章于 2025-06-20 16:58:47 发布

舒泽

最新推荐文章于 2025-06-20 16:58:47 发布

阅读量876

点赞数 3

CC 4.0 BY-SA版权

文章标签： nrf52832

本文链接：https://blog.csdn.net/qq_27006271/article/details/137264568

对于Nordic SDK的程序架构来说，引脚的NFC功能和Reset功能主要是在system_nrf52.c，跳转进main函数前执行SystemInit进行初始化的。代码如下

void SystemInit(void)
{
	......

    /* Configure NFCT pins as GPIOs if NFCT is not to be used in your code. If CONFIG_NFCT_PINS_AS_GPIOS is not defined,
       two GPIOs (see Product Specification to see which ones) will be reserved for NFC and will not be available as
       normal GPIOs. */
    #if defined (CONFIG_NFCT_PINS_AS_GPIOS)
        if ((NRF_UICR->NFCPINS & UICR_NFCPINS_PROTECT_Msk) == (UICR_NFCPINS_PROTECT_NFC << UICR_NFCPINS_PROTECT_Pos)){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->NFCPINS &= ~UICR_NFCPINS_PROTECT_Msk;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #endif

    /* Configure GPIO pads as pPin Reset pin if Pin Reset capabilities desired. If CONFIG_GPIO_AS_PINRESET is not
      defined, pin reset will not be available. One GPIO (see Product Specification to see which one) will then be
      reserved for PinReset and not available as normal GPIO. */
    #if defined (CONFIG_GPIO_AS_PINRESET)
        if (((NRF_UICR->PSELRESET[0] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos)) ||
            ((NRF_UICR->PSELRESET[1] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos))){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[0] = 21;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[1] = 21;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #endif

    SystemCoreClockUpdate();
}

由代码可以看出，特色功能的IO配置通用的配置方法是需要在编译选项里的全局变量进行设置的，如下：