HCIP 第一次实验

最新推荐文章于 2025-08-13 14:11:28 发布

澤117

最新推荐文章于 2025-08-13 14:11:28 发布

阅读量128

点赞数 1

CC 4.0 BY-SA版权

文章标签：网络运维

本文链接：https://blog.csdn.net/weixin_63910421/article/details/131839983

一、子网划分

二、配置IP地址

以R1为例配置IP

[R1]int g 0/0/0
[R1-GigabitEthernet0/0/0]ip add 19.168.0.18 28
[R1-GigabitEthernet0/0/0]int g 0/0/1
[R1-GigabitEthernet0/0/1]ip add 192.168.0.33 28

给R3配置换回接口IP地址

[R3-GigabitEthernet0/0/1]int l0
[R3-LoopBack0]ip add 192.168.0.1 30
[R3-LoopBack0]int l1
[R3-LoopBack1]ip add 192.168.0.5 30
[R3-LoopBack1]int l2
[R3-LoopBack2]ip add 192.168.0.9 30

配置完成如下

ISP

三、进行VLAN配置

sw1

[sw1]vlan batch 2 3
[sw1]int e0/0/1
[sw1-Ethernet0/0/1]port link-type access 
[sw1-Ethernet0/0/1]port default vlan 2
[sw1]int e0/0/2
[sw1-Ethernet0/0/2]port link-type access 
[sw1-Ethernet0/0/2]port default vlan 3
[sw1]int e0/0/3 
[sw1-Ethernet0/0/3]port link-type trunk  
[sw1-Ethernet0/0/3]port trunk allow-pass vlan all
[sw1]int e0/0/4 
[sw1-Ethernet0/0/4]port link-type trunk  
[sw1-Ethernet0/0/4]port trunk allow-pass vlan all

sw2

[sw2]vlan batch 2 3
[sw2]int e 0/0/1
[sw2-Ethernet0/0/1]port link-type access 
[sw2-Ethernet0/0/1]port default vlan 2
[s2]int e 0/0/2
[sw2-Ethernet0/0/2]port link-type access 
[sw2-Ethernet0/0/2]port default vlan 3
[sw2]int g 0/0/3 
[sw2-Ethernet0/0/2]port link-type trunk  
[sw2-Ethernet0/0/2]port trunk allow-pass vlan all

路由器子接口

[R4]int g0/0/2.1 
[R4-GigabitEthernet0/0/2.1]dot1q termination vid 2 
[R4-GigabitEthernet0/0/2.1]ip address 192.168.0.113 28
[R4-GigabitEthernet0/0/2.1]arp broadcast enable   
[R4]int g0/0/2.2
[R4-GigabitEthernet0/0/2.2]dot1q  termination vid 3
[R4-GigabitEthernet0/0/2.2]ip address  192.168.0.129 28
[R4-GigabitEthernet0/0/2.2]arp broadcast enable