三菱图形操作终端连接手册（非三菱产品1）.pdf资源-CSDN下载

版权申诉

32 浏览量 2025-08-03 23:41:43 上传评论收藏 21.25MB PDF 举报

资源推荐

资源详情

资源评论

■IAI ROBOT CONTROLLER

■AZBIL (former YAMATAKE) CONTROL

EQUIPMENT

■OMRON PLC

■OMRON TEMPERATURE CONTROLLER

■KEYENCE PLC

■KOYO EI PLC

■JTEKT PLC

■SHARP PLC

■SHINKO TECHNOS INDICATING

CONTROLLER

■CHINO CONTROLLER

■TOSHIBA MACHINE PLC

■TOSHIBA PLC

■PANASONIC SERVO AMPLIFIER

■PANASONIC INDUSTRIAL DEVICES

SUNX PLC

GRAPHIC OPERATION TERMINAL

Connection Manual

(Non-Mitsubishi Products 1)

For GT Works3 Version1

GOT2000 Series

A - 2

[DESIGN PRECAUTIONS]

WARNING

When the GOT backlight has a failure, the GOT status will be as follows. Failure to observe this

instruction may result in an accident due to incorrect output or malfunction.

• GT27, GT25, GT23

The POWER LED blinks (orange/blue), the display section dims, and inputs by a touch switch are

disabled.

• GT2105-Q

The POWER LED blinks (orange/blue), and the display section dims. However, inputs by a touch

switch are still available.

• GT2107, GT2104-R, GT2104-P, GT2103-P

The display section dims. However, inputs by a touch switch are still available.

Even if the display section dims, inputs by a touch switch may still be available. This may cause an

unintended operation of the touch switch.

For example, if an operator assumes that the display section has dimmed because of the screen

save function and touches the display section to cancel the screen save, a touch switch may be

activated.

The GOT backlight failure can be checked with a system signal of the GOT. (This system signal is

not available on GT2107, GT2104-R, GT2104-P, and GT2103-P.)

The display section of the GOT is an analog-resistive type touch panel.

When multiple points of the display section are touched simultaneously, an accident may occur due

to incorrect output or malfunction.

•GT27

Do not touch three points or more simultaneously on the display section. Doing so may cause an

accident due to an incorrect output or malfunction.

• GT25, GT23, GT21

Do not touch two points or more simultaneously on the display section. Doing so may cause a

touch switch near the touched points to operate unexpectedly, or may cause an accident due to

an incorrect output or malfunction.

When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are

changed, be sure to reset the GOT, or turn on the unit again after shutting off the power as soon as

possible.

Not doing so can cause an accident due to false output or malfunction.

If a communication fault (including cable disconnection) occurs during monitoring on the GOT,

communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

For bus connection (GT27, GT25 Only) : The CPU becomes faulty and the GOT becomes

inoperative.

For other than bus connection : The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the

system by using the switches of a device other than the GOT on the assumption that a GOT

communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

A - 3

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

CAUTION

Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm apart.

Not doing so noise can cause a malfunction.

Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

When the GOT connects to an Ethernet network, the IP address setting is restricted according to the

system configuration.

• GT27,GT25,GT23

When a GOT2000 series model and a GOT1000 series model are on an Ethernet network, do not

set the IP address 192.168.0.18 for the GOTs and the controllers on this network.

Doing so can cause IP address duplication at the GOT startup, adversely affecting the

communication of the device with the IP address 192.168.0.18.

The operation at the IP address duplication depends on the devices and the system.

•GT21

• When multiple GOTs connect to the Ethernet network:

Do not set the IP address (192.168.3.18) for the GOTs and the controllers in the network.

• When one GOT connects to the Ethernet network:

Do not set the IP address (192.168.3.18) for the controllers other than the GOT in the network.

Doing so can cause IP address duplication at the GOT startup, adversely affecting the

communication of the device with the IP address 192.168.3.18.

The operation at the IP address duplication depends on the devices and the system.

Turn on the controllers and the network devices to be ready for communication before they

communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

When the GOT is subject to shock or vibration, or some colors appear on the screen of the GOT, the

screen of the GOT might flicker.

WARNING

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the option unit onto/from the GOT. (GT27, GT25 Only)

Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

剩余579页未读，继续阅读

评论收藏

内容反馈

版权申诉

wwwarewow

粉丝: 4762

三菱图形操作终端连接手册（非三菱产品1）.pdf

三菱人机界面产品—A970GOT手册1.pdf

三菱人机界面产品—F900GOT 操作手册-B.pdf

三菱人机界面产品—AGOT 900用户手册.pdf

三菱人机界面产品—F930GOT-BWD-E用户手册.pdf

A900GOT操作手册 扩展功能篇.pdf

三菱RH-6SDH/12SDH/18SDH 系列机器人产品样本.pdf

GOT-F900系列触摸屏硬件手册(接线篇).pdf

三菱 MELDAS分度功能内藏AC伺服MR-J2-CT系列使用手册.pdf

GT-Designer3画面设计手册公共篇.pdf

A900通訓使用手冊.pdf

三菱电机GT-Designer3画面设计手册(绘图篇)

A900使用手冊.pdf

DP210使用手册.pdf

DeepSeek从入门到精通(20250204)-清华团队.pdf

相关实用应用程序（Windows可用）

Visio2013 安装包及破解方法

测控方向电赛基于TI系列MSPM0G3507的循迹小车（带避障功能）.zip

李飞飞自传 我看见的世界 The World I see

清华大学-DeepSeek从入门到精通

DeepSeek 15天指导手册-从入门到精通.pdf

ChatGPT使用总结：150个ChatGPT提示词模板（完整版）

全国计算机二级WPSoffice精选350道选择题题库（含答案）.pdf

DeepSeek从入门到精通：中国开源推理模型的综合指南（104 页）

汽车智能驾驶技术及产业发展白皮书

ISO 34505:2025《道路车辆 自动驾驶系统测试场景 场景评价与测试用例生成》

visio2021-64位.7z

基于TI的MSPM0G3507制作24年电赛H题自动行驶小车.zip

哈尔滨工业大学-ChatGPT调研报告-2023.3.6-94页.pdf

学术海报模板+论文科研+研究生

WP学习记录

TerraExplorer Pro6.5中文补丁

最新资源

A900GOT操作手册扩展功能篇.pdf

李飞飞自传我看见的世界 The World I see

ISO 34505:2025《道路车辆自动驾驶系统测试场景场景评价与测试用例生成》