intel 网卡MAC地址修改工具 EEUpdate 5.17.19.02

Intel(R) EEUpdate Release Notes ================================ April 26, 2005 DISCLAIMER ========== This software is furnished under license and may only be used or copied in accordance with the terms of the license. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Intel Corporation. Intel Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in this document or any software that may be provided in association with this document. Except as permitted by such license, no part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Intel Corporation. Contents ======== - OVERVIEW - RUNNING THE UTILITY - OPTIONS - BASIC USAGE GUIDELINES - EEPROM IMAGE FILE FORMAT - MAC ADDRESS FILE FORMAT - EELOG.DAT - EXAMPLES - ERROR CODES - INSTALLATION - CUSTOMER SUPPORT -LEGAL OVERVIEW ======== EEUpdate is the EEPROM Update Utility. Allows manufacturing programming of EEPROMs, in cases where EEPROM is not preprogrammed, or programmed at In-circuit test. RUNNING THE UTILITY =================== Using the "/?" option will display a list of supported command line options. NOTE: EEPROM checksums and CRCs are automatically updated with any command that modifies the EEPROM contents. In order to prevent these from being updated, use the "/NOCHKSUM" option in the command line. OPTIONS: -------- EEUPDATE can be run with any of the following command line options: /HELP or /? Displays command line help. /EXITCODES Displays exit code help. /ALL Selects all adapters found in the system. /NIC=XX Selects a specific adapter (1-32). /BUS=XX Selects PCI bus of adapter to program. Must be used with the DEV parameter to specify an adapter. /DEV=XX Selects PCI device of the adapter to program. Must be used with the BUS parameter to specify an adapter. /FUN=XX Selects PCI function of the adapter to program. Must be used with both the BUS and DEV parameters to specify an adapter. /DEVICE=<pci device id> 4 hex digit device id of card to program. /DUMP Dumps EEPROM memory contents to file. /CB <offset> <bitmask> Clears bits in the EEPROM, specified in <bitmask>. /SB <offset> <bitmask> Sets bits in the EEPROM, specified in <bitmask>. /RW <word> Reads <word> from the EEPROM. /WW <word> <value> Writes <value> into <word> in EEPROM. /MAC=macaddr Programs the EEPROM with only the MAC address of macaddr without changing the rest of the EEPROM. /A <addrfile> or /address <addrfile> Programs the EEPROM with only the MAC address from the <addrfile> without changing the rest of the EEPROM. /D <imagefile> or /DATA <imagefile> Programs the EEPROM with the contents of <imagefile> without changing the MAC address. /NOCHKSUM Prevents EEPROM checksum and CRCs from being updated. /CALCCHKSUM Forces the EEPROM checksum and CRCs to be updated. /EEPROMVER Displays the version of the EEPROM image. /PCIINFO Displays the PCI information of the adapter. /TEST Checks the EEPROM checksum and size. /IDFLASH Displays the flash ID and its protected status. /DEFAULTCONFIG or /DEFCFG Resets words 30h to 32h back to default. /BOOTDISABLE or /BD Disables Boot ROM. /BOOTENABLE or /BE Enables Boot ROM. /WOLDISABLE or /WOLD Disables WOL bit. /WOLENABLE or /WOLE Enables WOL bit. /SETUPENABLE or /STE Enables Setup Menu. /SETUPDISABLE or /STD Disables Setup Menu. /TITLEENABLE or /TLE Enables Initial Title Message. /TITLEDISABLE or /TLD Disables Initial Title Message. /PROTOCOLENABLE or /PROE Enables Changing the Boot Protocol Option. /PROTOCOLDISABLE or /PROD Disables Changing the Boot Protocol Option. /ORDERENABLE or /ORDE Enables Changing the Boot Order Option. /ORDERDISABLE or /ORDD Disables Changing the Boot Order Option. /LWSENABLE or /LWSE Enables Changing the Legacy OS Wakeup Support Option. /LWSDISABLE or /LWSD Disables Changing the Legacy OS Wakeup Support Option. /SETWAITTIME=X or /SWT=X Changes the setup message delay time (0, 2, 3, 5) on the NIC. /BMCMAC_DUMP Displays the dedicated MAC address for the BMC. /MNGMAC=macaddr Programs the dedicated MAC address for the manageability component without changing the rest of the EEPROM. /MNGADDRESS <addrfile> Programs the dedicated MAC address for the manageability component with the MAC address from <addrfile>. /VERSION Displays version and the diagnostic library information. /GUI Brings up GUI mode. /NOPROT On AMT, while programming an image, disables protection. Note this switch has no effect if not used with the /data command. /BMCMAC=macaddr is replaced with MNGMAC command. /BMCADDRESS <addrfile> is replaced with MNGADDRESS command. /RETAINMNGMAC Uses the manageability MAC address in the NVM rather than the image /DEBUGLOG <debugfile> Log debug messages into the debugfile. /VERIFY <targetfile> Verifies the eeprom image in eeprom to the target file specified in <targetfile>. BASIC USAGE GUIDELINES ---------------------- To display a list of installed adapters call EEUPDATE without any parameters as follows: EEUPDATE EEUPDATE will display a list of network adapters installed in the system similar to the following: [EEUPDATE ver 5.0.1.0] - Intel PCI NIC EEPROM Utility Copyright (C) 1995 - 2004 Intel Corporation Intel (R) Confidential and not for general distribution. Warning: No Adapter Selected NIC Bus Dev Fun Vendor-Device Branding string === === === === ============= ================================================= 1 1 00 00 8086-1008 Intel(R) PRO/1000 XT Server Adapter 2 1 08 00 8086-1039 Intel(R) PRO/100 VE Network Connection To perform an operation on an installed network adapter you must specify the "/NIC=" parameter. For example, to perform an EEPROM dump on NIC 3 from the list above call EEUPDATE like this: EEUPDATE /NIC=3 /DUMP Alternatively you may specify the "/BUS=" and "/DEV=" parameters instead of the "/NIC=" parameter to specify which network adapter to select. For example to program NIC 1 from the list above with the EEPROM image file "image.eep" call EEUPDATE.EXE as follows: EEUPDATE /BUS=0 /DEV=D /DATA image.eep EEPROM IMAGE FILE FORMAT ------------------------ The <imagefile> parameter designates a text file which contains hexadecimal values with which to program the EEPROM. Each value should consist of up to four hex digits seperated by a space or newline. The data contained in <imagefile> must be formatted the same as the EEPROM imagefile produced by the "/dump" parameter. An imagefile produced by the "/dump" parameter may be used to program the EEPROM. Comments may be added to the EEPROM image file as long as they are preceded by a semicolon ';'. NOTE: When programming the EEPROM using the "/DATA" parameter, EEupdate will ignore the MAC Address (first 6 bytes), and EEPROM checksum (last 2 bytes). However, the MAC Address and checksum locations in the EEPROM image file must be filled with valid hexadecimal val