a) Prueba del estado del AO

Seleccione para trabajar uno de los cuatro AO que vienen en el integrado. Monte el circuito de la
figura 1 (seguidor de voltaje o buffer) y aplique en la entrada una señal senoidal de 1V pico y
frecuencia de 1kHz (Vi). El voltaje de salida Vo debe ser igual a Vi si el AO está bueno.

Recuerde que el generador de señales posee una resistencia interna, por lo tanto las señales de entrada
Vi deben ser medidas con el osciloscopio en el punto indicado.

+10V

+
Generador de -1/1V Rs -10V 10k Vo = Vi
señales con Vi RL
resistencia -
1kHz
interna
Vs

Figura 1

Vi = Vo = 0.35 V

Por lo tanto, el Amplificador Operacional está funcionando.

b) Medida de la impedancia de entrada del AO (Zin).

Monte el circuito de la figura 2 y mida el voltaje en la resistencia R. Calcule:

Ii = VR / R R = 100 K Zi = Vi / I

c) Medida del ancho de banda en configuración de seguidor de voltaje.

Construya el circuito de la figura 3 y mida diferentes valores de Vo, Vi y f. Con estos datos realice
una gráfica de respuesta en frecuencia como la que se muestra en la figura 4.

Av = Vo /
Vi Vi = 1Vpico / senoidal

+10V

+
Generador de -1/1V Rs -10V 10k
RL Vo
señales con
resistencia -
1kHz
interna Vs

Figura 3
Tome suficientes puntos para elaborar la curva. Anote el punto en el cual la ganancia cae al 70% de
la ganancia máxima, en ese punto se tiene la frecuencia de corte y se determina el ancho de banda del
AO.

Dibuje la curva sobre papel semilogarítmico, tomando el eje lineal para la ganancia y el eje
logarítmico para la frecuencia.

Av

Respuesta en frecuencia del AO

1
0,7

Figura
f
4
fc

d) Medida de la máxima corriente de salida.

Utilice el circuito que se muestra en la figura 3, fije la señal de entrada Vi en 1Vpico y f =

1kHz. En la salida del circuito conecte el potenciómetro de 1K (o valor cercano), entre la salida y
tierra (recuerde que se trabaja con el centro y un extremo del potenciómetro).

Partiendo del máximo valor de resistencia, mueva el eje del potenciómetro para que su
resistencia disminuya hasta que la señal de salida aparezca recortada. En ese momento retire el
potenciómetro del circuito y mida su valor de resistencia. Calcule:

Iomax = Vo / Rpoten

e) Medida del slew rate.

Utilice el circuito de la figura 3, fije la señal de entrada Vi en una onda cuadrada de 2V pico y f=
10kHz. Observe y compare Vo contra Vi. Mida la pendiente de subida de la señal de voltaje Vo.
Este valor se expresa en V/µs y es un indicador de la velocidad del AO.
f) Medida del tiempo de establecimiento.

Con las mismas condiciones del punto anterior, aumente la frecuencia de la señal de entrada Vi
hasta obtener en la salida una señal como la que se muestra en la figura 5. Mida el tiempo de
establecimiento: ts.

ts
Ts= 1,2 us

g) Medida de voltajes de saturación

Monte el circuito de la figura 6 y aplique una señal de entrada Vi de 1V pico y f = 1kHz. Observe
que el voltaje de salida aparece saturado positiva y negativamente. Mida estos niveles o voltajes de
saturación y calcule su diferencia con los voltajes de la fuente de alimentación. En los manuales de
componentes estos valores aparecen como: “voltaje swing”.
+10V Vo
+
+Vsat
+ t
Generador de -1/1V Rs -10V 10k Vo
señales con Vi RL
resistencia - -Vsat
1kHz
interna Vs

Figura 6
Vf = 10 V
Vo= 8.45 V
VSaturación = Vf –Vo = 10 V- 8.45V = 1.55 V

h) Medida del factor de rechazo en modo común CMRR.

Monte el circuito de la figura 7 y aplique una señal de entrada Vi de 1Vpico y f = 1kHz. Mida
Vo y calcule CMRR:
 o CMRR (dB) = 20 log (Vi / Vo) R = 10 K
R
+10V

CMRR = R
Vi / Vo
+
R
-1/1V Rs -10V 10k
RL Vo
Vi R
-
1kHz
Vs

Generador de
señales con
resistencia
interna

CMRR = Vi / Vo
CMRR= 0.50 V/ 8.48V
CMRR = 0.0589
i) Medida del voltaje offset.

Monte el circuito de la figura 8, observe que tiene las entradas conectadas a tierra. Mida el
voltaje offset en la salida y calcule:

Voffset in = (Voffset out) / Av y Av = 1000 (por la relación de resistencias)

1Meg

+10V

1k +

-10V
10k Voffset
RL out

Figura 8

Voffset out = 0.01 V

Av = 1000
Voffset in = Voffset out / Av
Voffset in =0.01 / 1000
Voffset in = 1*10^ - 5V
 Order this document by TL071C/D

 
 
     
 
These low noise JFET input operational amplifiers combine two
state–of–the–art analog technologies on a single monolithic integrated LOW NOISE, JFET INPUT
circuit. Each internally compensated operational amplifier has well matched OPERATIONAL AMPLIFIERS
high voltage JFET input device for low input offset voltage. The BIFET
technology provides wide bandwidths and fast slew rates with low input bias
currents, input offset currents, and supply currents. Moreover, the devices SEMICONDUCTOR
exhibit low noise and low harmonic distortion, making them ideal for use in TECHNICAL DATA
high fidelity audio amplifier applications.
These devices are available in single, dual and quad operational
amplifiers which are pin–compatible with the industry standard MC1741,
MC1458, and the MC3403/LM324 bipolar products.

• Low Input Noise Voltage: 18 nV/ ǸHz Typ

8
8 1
1
• Low Harmonic Distortion: 0.01% Typ P SUFFIX D SUFFIX
• Low Input Bias and Offset Currents PLASTIC PACKAGE PLASTIC PACKAGE
• High Input Impedance: 1012 Ω Typ
CASE 626 CASE 751
(SO–8)
• High Slew Rate: 13 V/µs Typ
• Wide Gain Bandwidth: 4.0 MHz Typ
PIN CONNECTIONS

• Low Supply Current: 1.4 mA per Amp Offset Null 1 8 NC

Inv + Input 2 7 VCC
Noninvt Input 3 + 6 Output
VEE 4 5 Offset Null
TL071 (Top View)

Output A 1 8 VCC
2 – 7 Output B
Inputs A +
3 – 6
+ Inputs B
VEE 4 5
TL072 (Top View)

N SUFFIX
PLASTIC PACKAGE
CASE 646
14
(TL074 Only)
1

PIN CONNECTIONS

Output 1 1 14 Output 4

ORDERING INFORMATION 2 – – 13
Inputs 1 +
Inputs 4
+
3 1 4 12
Op Amp Operating
Function Device Temperature Range Package VCC 4 11 VEE
TL071CD SO–8 5 + + 10
Single TA = 0° to +70°C Inputs 2 – –
Inputs 3
TL071ACP Plastic DIP 6 2 3 9
TL072CD SO–8 Output 2 7 8 Output 3
Dual TA = 0° to +70°C
TL072ACP Plastic DIP TL074 (Top View)
Quad TL074CN, ACN TA = 0° to +70°C Plastic DIP

 Motorola, Inc. 1997 Rev 1

MOTOROLA ANALOG IC DEVICE DATA 1
 TL071C,AC TL072C,AC TL074C,AC

MAXIMUM RATINGS
Rating Symbol Value Unit
Supply Voltage VCC 18 V
VEE –18
Differential Input Voltage VID ±30 V
Input Voltage Range (Note 1) VIDR ±15 V
Output Short Circuit Duration (Note 2) tSC Continuous
Power Dissipation
Plastic Package (N, P) PD 680 mW
Derate above TA = 47°C 1.0/θJA 10 mW/°C
Operating Ambient Temperature Range TA 0 to +70 °C
Storage Temperature Range Tstg –65 to +150 °C
NOTES: 1. The magnitude of the input voltage must not exceed the magnitude of the supply voltage or
15 V, whichever is less.
2. The output may be shorted to ground or either supply. Temperature and/or supply voltages
must be limited to ensure that power dissipation ratings are not exceeded.
3. ESD data available upon request.

ELECTRICAL CHARACTERISTICS (VCC = 15 V, VEE = –15 V, TA = Thigh to Tlow [Note 1])

Characteristics Symbol Min Typ Max Unit
Input Offset Voltage (RS ≤ 10 k, VCM = 0) VIO mV
TL071C, TL072C – – 13
TL074C – – 13
TL07_AC – – 7.5
Input Offset Current (VCM = 0) (Note 2) IIO nA
TL07_C – – 2.0
TL07_AC – – 2.0
Input Bias Current (VCM = 0) (Note 2) IIB nA
TL07_C – – 7.0
TL07_AC – – 7.0
Large–Signal Voltage Gain (VO = ±10 V, RL ≥ 2.0 k) AVOL V/mV
TL07_C 15 – –
TL07_AC 25 – –
Output Voltage Swing (Peak–to–Peak) VO V
(RL ≥ 10 k) 24 – –
(RL ≥ 2.0 k) 20 – –
NOTES: 1. Tlow = 0°C for TL071C,AC Thigh = 70°C for TL071C,AC
0°C for TL072C,AC Thigh = 70°C for TL072C,AC
0°C for TL074C,AC Thigh = 70°C for TL074C,AC
2. Input Bias currents of JFET input op amps approximately double for every 10°C rise in junction temperature as shown in Figure 3. To maintain
junction temperature as close to ambient temperature as possible, pulse techniques must be used during testing.

Figure 1. Unity Gain Voltage Follower Figure 2. Inverting Gain of 10 Amplifier

10 k

1.0 k
– –
VO Vin VO
+ +
Vin

RL = 2.0 k CL = 100 pF RL CL = 100 pF

2 MOTOROLA ANALOG IC DEVICE DATA

 TL071C,AC TL072C,AC TL074C,AC

ELECTRICAL CHARACTERISTICS (VCC = 15 V, VEE = –15 V, TA = 25°C, unless otherwise noted.)

Characteristics Symbol Min Typ Max Unit
Input Offset Voltage (RS ≤ 10 k, VCM = 0) VIO mV
TL071C, TL072C – 3.0 10
TL074C – 3.0 10
TL07_AC – 3.0 6.0
Average Temperature Coefficient of Input Offset Voltage ∆VIO/∆T – 10 – µV/°C
RS = 50 Ω, TA = Tlow to Thigh (Note 1)
Input Offset Current (VCM = 0) (Note 2) IIO pA
TL07_C – 5.0 50
TL07_AC – 5.0 50
Input Bias Current (VCM = 0) (Note 2) IIB pA
TL07_C – 30 200
TL07_AC – 30 200
Input Resistance ri – 1012 – Ω
Common Mode Input Voltage Range VICR V
TL07_C ±10 15, –12 –
TL07_AC ±11 15, –12 –
Large–Signal Voltage Gain (VO = ±10 V, RL ≥ 2.0 k) AVOL V/mV
TL07_C 25 150 –
TL07_AC 50 150 –
Output Voltage Swing (Peak–to–Peak) VO 24 28 – V
(RL = 10 k)
Common Mode Rejection Ratio (RS ≤ 10 k) CMRR dB
TL07_C 70 100 –
TL07_AC 80 100 –
Supply Voltage Rejection Ratio (RS ≤ 10 k) PSRR dB
TL07_C 70 100 –
TL07_AC 80 100 –
Supply Current (Each Amplifier) ID – 1.4 2.5 mA
Unity Gain Bandwidth BW – 4.0 – MHz
Slew Rate (See Figure 1) SR – 13 – v/µs
Vin = 10 V, RL = 2.0 k, CL = 100 pF
Rise Time (See Figure 1) tr – 0.1 – µs
Overshoot (Vin = 20 mV, RL = 2.0 k, CL = 100 pF) OS – 10 – %
Equivalent Input Noise Voltage en – 18 – nV/ √ Hz
RS = 100 Ω, f = 1000 Hz
Equivalent Input Noise Current in – 0.01 – pA/ √ Hz
RS = 100 Ω, f = 1000 Hz
Total Harmonic Distortion THD – 0.01 – %
VO (RMS) = 10 V, RS ≤ 1.0 k, RL ≥ 2.0 k, f = 1000 Hz
Channel Separation CS – 120 – dB
AV = 100
NOTES: 1. Tlow = 0°C for TL071C,AC Thigh = 70°C for TL071C,AC
0°C for TL072C,AC Thigh = 70°C for TL072C,AC
0°C for TL074C,AC Thigh = 70°C for TL074C,AC
2. Input Bias currents of JFET input op amps approximately double for every 10°C rise in junction temperature as shown in Figure 3. To maintain
junction temperature as close to ambient temperature as possible, pulse techniques must be used during testing.

MOTOROLA ANALOG IC DEVICE DATA 3

 TL071C,AC TL072C,AC TL074C,AC

Figure 3. Input Bias Current Figure 4. Output Voltage Swing

versus Temperature versus Frequency
100 35
RL = 2.0 k

VO, OUTPUT VOLTAGE SWING (Vpp )

30 TA = 25°C
IIB , INPUT BIAS CURRENT (nA)

VCC/VEE = ±15 V VCC/VEE = ±15 V (See Figure 2)

10
25

20 ±10 V
1.0
15

10 ±5.0 V
0.1
5.0

0.01 0
–100 –75 –50 –25 0 25 50 75 100 125 150 100 1.0 k 10 k 100 k 1.0 M 10 M
TA, AMBIENT TEMPERATURE (°C) f, FREQUENCY (Hz)

Figure 5. Output Voltage Swing Figure 6. Output Voltage Swing

versus Load Resistance versus Supply Voltage
40 40

VO, OUTPUT VOLTAGE SWING (Vpp )

VO, OUTPUT VOLTAGE SWING (Vpp )

VCC/VEE = ±15 V RL = 2.0 k

TA = 25°C TA = 25°C
30
(See Figure 2) 30

20
20
10

10
5.0

0 0
0.1 0.2 0.4 0.7 1.0 2.0 4.0 7.0 10 0 5.0 10 15 20
RL, LOAD RESISTANCE (kΩ) VCC, |VEE| , SUPPLY VOLTAGE (±V)

Figure 7. Output Voltage Swing Figure 8. Supply Current per Amplifier

versus Temperature versus Temperature
40 2.0
VCC/VEE = ±15 V
VCC/VEE = ±15 V
VO, OUTPUT VOLTAGE SWING (Vpp )

1.8
ID , SUPPLY DRAIN CURRENT (mA)

35
(See Figure 2)
1.6
30 RL = 10 k
1.4
25 1.2
RL = 2.0 k
20 1.0

15 0.8
0.6
10 0.4
5.0 0.2
0 0
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)

4 MOTOROLA ANALOG IC DEVICE DATA

 TL071C,AC TL072C,AC TL074C,AC

Figure 9. Large Signal Voltage Gain and Figure 10. Large Signal Voltage Gain
Phase Shift versus Frequency versus Temperature
108 1000
VCC/VEE = ±15 V VCC/VEE = ±15 V
107 VO = ±10 V

VVOL, VOLTAGE GAIN (V/mV)

RL = 2.0 k

PHASE SHIFT (DEGREES)

RL = 2.0 k
VVOL, OPEN–LOOP GAIN

106 TA = 25°C
100
105
104 0°
Gain
103 45° 10
102 90°
Phase Shift
101 135°

1.0 180° 1.0

1.0 10 100 1.0 k 10 k 100 k 1.0 M 10 M 100 M –100 –75 –50 –25 0 25 50 75 100 125 150
f, FREQUENCY (Hz) TA, AMBIENT TEMPERATURE (°C)

Figure 11. Normalized Slew Rate Figure 12. Equivalent Input Noise Voltage
versus Temperature versus Frequency

en, EQUIVALENT INPUT NOISE VOLTAGE ( nV/ √ Hz )

1.20 70
VCC/VEE = ±15 Vdc
1.15 60 AV = 10
RS = 100 Ω
NORMALIZED SLEW RATE

1.10
50 TA = 25°C
1.05
40
1.0
30
0.95

0.90 20

0.85 10

0.80 0
–75 –50 –25 0 25 50 75 100 125 0.01 0.05 0.1 0.5 1.0 5.0 10 50 100
TA, AMBIENT TEMPERATURE (°C) f, FREQUENCY (Hz)

Figure 13. Total Harmonic Distortion

versus Frequency
1.0
THD, TOTAL HARMONIC DISTORTION (%)

VCC/VEE = ±15 V
0.5 AV = 1.0
VO = 6.0 V (RMS)
TA = 25°C
0.1

0.05

0.01

0.005

0.001
0.1 0.5 1.0 5.0 10 50 100
f, FREQUENCY (Hz)

MOTOROLA ANALOG IC DEVICE DATA 5

 TL071C,AC TL072C,AC TL074C,AC

Representative Schematic Diagram

(Each Amplifier) Bias Circuitry
Output Common to All
Amplifiers
VCC
Q4 Q5 Q2
Q3 Q1

Q6
– J1 J2
Inputs
2.0 k
+ Q17

Q20
J3
Q15 Q19 Q23
10 pF 24
Q14
Q21
Q22
Q24
Q12 Q13 Q16

Q10 Q9 Q8 Q25
Q11
Q7

Q18
Offset
Null 1.5 k 1.5 k
(TL071
only) VEE

Figure 14. Audio Tone Control Amplifier

10 k 100 k 10 k
Input

0.033 µF 0.033 µF VCC

10 k
–
TL071 Output
+
3.3 k
68 k VEE
0.033 µF 0.033 µF Turn–Over Frequency = 1.0 kHz
Bass Boost/Cut — ±20 dB at 20 Hz
100 k Treble Boost/Cut — ±19 dB at 20 kHz

Figure 15. High Q Notch Filter

–
R R TL071
Input +
C1

R1 fo+ 2p1RC + 350 Hz

R + 2R1 + 1.5 M
C C C + C1 + 300 pF
2

6 MOTOROLA ANALOG IC DEVICE DATA

 TL071C,AC TL072C,AC TL074C,AC

OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE K

8 5
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
–B– FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
1 4 SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
F MILLIMETERS INCHES
DIM MIN MAX MIN MAX
NOTE 2 –A– A 9.40 10.16 0.370 0.400
L B 6.10 6.60 0.240 0.260
C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020
F 1.02 1.78 0.040 0.070
C G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
–T– J K 2.92 3.43 0.115 0.135
SEATING N L 7.62 BSC 0.300 BSC
PLANE M ––– 10_ ––– 10_
M N 0.76 1.01 0.030 0.040
D K
H G
0.13 (0.005) M T A M B M

D SUFFIX
PLASTIC PACKAGE
CASE 751–05
(SO–8)
ISSUE S

NOTES:
A D 1. DIMENSIONING AND TOLERANCING PER ASME
C
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETERS.
8 5 3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
E H 0.25 M B M
5. DIMENSION B DOES NOT INCLUDE MOLD
1 PROTRUSION. ALLOWABLE DAMBAR
4 PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
h X 45 _
B q MILLIMETERS
e DIM MIN MAX
A 1.35 1.75
A A1 0.10 0.25
C B 0.35 0.49
SEATING C 0.18 0.25
PLANE D 4.80 5.00
L E 3.80 4.00
0.10 e 1.27 BSC
H 5.80 6.20
A1 B h 0.25 0.50
L 0.40 1.25
0.25 M C B S A S
q 0_ 7_

MOTOROLA ANALOG IC DEVICE DATA 7

 TL071C,AC TL072C,AC TL074C,AC

OUTLINE DIMENSIONS
N SUFFIX
PLASTIC PACKAGE
CASE 646–06
ISSUE M NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14 8 2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
B FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
1 7 5. ROUNDED CORNERS OPTIONAL.

INCHES MILLIMETERS
A DIM MIN MAX MIN MAX
A 0.715 0.770 18.16 18.80
F L B 0.240 0.260 6.10 6.60
C 0.145 0.185 3.69 4.69
D 0.015 0.021 0.38 0.53
N F 0.040 0.070 1.02 1.78
C G 0.100 BSC 2.54 BSC
H 0.052 0.095 1.32 2.41
–T– J 0.008 0.015 0.20 0.38
K 0.115 0.135 2.92 3.43
SEATING
PLANE L 0.290 0.310 7.37 7.87
K J M ––– 10_ ––– 10_
H G D 14 PL M N 0.015 0.039 0.38 1.01

0.13 (0.005) M

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

Mfax is a trademark of Motorola, Inc.

How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488

Customer Focus Center: 1–800–521–6274

Mfax: [email protected] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
Motorola Fax Back System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
– http://sps.motorola.com/mfax/
HOME PAGE: http://motorola.com/sps/

8 ◊ MOTOROLA ANALOG IC DEVICE DATA

TL071C/D
 TL084
 TL084A - TL084B
GENERAL PURPOSEJ-FET
QUAD OPERATIONAL AMPLIFIERS

. WIDE COMMON-MODE (UP TO VCC+) AND

.. DIFFERENTIAL VOLTAGE RANGE

LOW INPUT BIAS AND OFFSET CURRENT

. OUTPUT SHORT-CIRCUIT PROTECTION

HIGH INPUT IMPEDANCE J–FET INPUT

.. STAGE
INTERNAL FREQUENCY COMPENSATION

.
N D
LATCH UP FREE OPERATION DIP14 SO14
HIGH SLEW RATE : 16V/µs (typ) (Plastic Package) (Plastic Micropackage)

P
TSSOP14
(Thin Shrink Small Outline Package)

DESCRIPTION ORDER CODES

The TL084, TL084A and TL084B are high speed Temperature Package
J–FET input quad operationalamplifiers incorporating Part Number
Range N D P
well matched, high voltage J–FET and bipolar transis- o o
TL084M/AM/BM –55 C, +125 C • • •
tors in a monolithic integrated circuit. o o
TL084I/AI/BI –40 C, +105 C • • •
The devicesfeaturehigh slew rates, low input bias and o o
offset currents, and low offset voltage temperature TL084C/AC/BC 0 C, +70 C • • •
coefficient. Examples : TL084CN, TL084CD

PIN CONNECTIONS (top view)

Output 1 1 14 Output 4

Inverting Input 1 2 - - 13 Inverting Input 4

Non-inverting Input 1 3 + + 12 Non-inverting Input 4

VCC + 4 11 VCC -

Non-inverting Input 2 5 + + 10 Non-inverting Input 3

Inverting Input 2 6 - - 9 Inverting Input 3

Output 2 7 8 Output 3

January 1999 1/11

TL084 - TL084A - TL084B

SCHEMATIC DIAGRAM (each amplifier)

VCC

Non- inver ting

input
I nverting
input
1 0 0Ω
2 0 0Ω
Output

1 0 0Ω
30k

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

VCC

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage - (note 1) ±18 V
Vi Input Voltage - (note 3) ±15 V
Vid Differential Input Voltage - (note 2) ±30 V
Ptot Power Dissipation 680 mW
Output Short-circuit Duration - (note 4) Infinite
o
Toper Operating Free Air Temperature Range TL084C,AC,BC 0 to 70 C
TL084I,AI,BI –40 to 105
TL084M,AM,BM –55 to 125
o
Tstg Storage Temperature Range –65 to 150 C
Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the
zero reference level is the midpoint between VCC+ and VCC–.
2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.

2/11
 TL084 - TL084A - TL084B

ELECTRICAL CHARACTERISTICS
VCC = ±15V, Tamb = 25oC (unless otherwise specified)
TL084I,M,AC,AI,
TL084C
Symbol Parameter AM,BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Vio Input Offset Voltage (R S = 50Ω) mV
o
Tamb = 25 C TL084 3 10 3 10
TL084A 3 6
TL084B 1 3
Tmin. ≤ Tamb ≤ Tmax. TL084 13 13
TL084A 7
TL084B 5
o
DV io Input Offset Voltage Drift 10 10 µV/ C
Iio Input Offset Current *
o
Tamb = 25 C 5 100 5 100 pA
Tmin. ≤ Tamb ≤ Tmax. 4 4 nA
Iib Input Bias Current *
o
Tamb = 25 C 20 200 30 400 pA
Tmin. ≤ Tamb ≤ Tmax. 20 20 nA
Avd Large Signal Voltage Gain (RL = 2kΩ, VO = ±10V) V/mV
Tamb = 25oC 50 200 25 200
Tmin. ≤ Tamb ≤ Tmax. 25 15
SVR Supply Voltage Rejection Ratio (R S = 50Ω) dB
o
Tamb = 25 C 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
ICC Supply Current, per Amp, no Load mA
Tamb = 25oC 1.4 2.5 1.4 2.5
Tmin. ≤ Tamb ≤ Tmax. 2.5 2.5
Vicm Input Common Mode Voltage Range ±11 +15 ±11 +15 V
-12 -12
CMR Common Mode Rejection Ratio (RS = 50Ω) dB
o
Tamb = 25 C 80 86 70 86
Tmin. ≤ Tamb ≤ Tmax. 80 70
Ios Output Short-circuit Current mA
o
Tamb = 25 C 10 40 60 10 40 60
Tmin. ≤ Tamb ≤ Tmax. 10 60 10 60
±VOPP Output Voltage Swing V
o
Tamb = 25 C RL = 2kΩ 10 12 10 12
RL = 10kΩ 12 13.5 12 13.5
Tmin. ≤ Tamb ≤ Tmax. RL = 2kΩ 10 10
RL = 10kΩ 12 12
SR Slew Rate (Vin = 10V, RL = 2kΩ, CL = 100pF, V/µs
o
Tamb = 25 C, unity gain) 8 16 8 16
tr Rise Time (Vin = 20mV, RL = 2kΩ, C L = 100pF, µs
Tamb = 25oC, unity gain) 0.1 0.1
KOV Overshoot (Vin = 20mV, RL = 2kΩ, C L = 100pF, %
o
Tamb = 25 C, unity gain) 10 10
GBP Gain Bandwidth Product (f = 100kHz, MHz
Tamb = 25oC, Vin = 10mV, R L = 2kΩ, C L = 100pF) 2.5 4 2.5 4
12 12
Ri Input Resistance 10 10 Ω
THD Total Harmonic Distortion (f = 1kHz, AV = 20dB, %
RL = 2kΩ, C L = 100pF, Tamb = 25oC, VO = 2VPP) 0.01 0.01
Equivalent Input Noise Voltage nV
en 15
(f = 1kHz, Rs = 100Ω) 15 √

Hz
∅m Phase Margin 45 45 Degrees
VO1/VO2 Channel Separation (Av = 100) 120 120 dB
* The input bias currents are junction leakage currents which approximately double for every 10oC increase in the junction temperature.

3/11
TL084 - TL084A - TL084B

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREQUENCY

MAXIMUMPEAK-TO-PEAK OUTPUT
30 30
V CC = 15V R L = 2kΩ R L= 10kΩ
MAXIMUM PEAK-TO-PEAKOUTPUT

25 T a m b = + 25° C 25 Tamb = +25 C

V CC = 15V
S ee Fig ure 2 See Figure 2
20

VOLTAGE (V)
20
VOLTAGE (V)

V CC = 10V VCC = 10V

15 15
10 10
V CC = 5V V CC = 5V
5 5
0 0
100 1K 10K 100K 1M 10M 100 1K 10K 100K 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS FREQUENCY VOLTAGE VERSUS FREE AIR TEMP.
MAXIMUMPEAK-TO-PEAK OUTPUT

30
30
MAXIMUM PEAK-TO-PEAKOUTPUT

Ta mb = +25 C VCC = 15V

25
R L = 2kΩ 25
VOLTAGE (V)

20 S ee Figure 2
20
VOLTAGE (V)

R L = 1 0 kΩ
15 15
Ta mb = -55 C R L = 2 kΩ
10 10

5 5 VC C = 15 V
Ta mb = +125 C S e e F i g u re 2
0 0
10k 40k 100k 400k 1M 4M 10M -7 5 -5 0 - 25 0 25 50 75 -50 125

T E MP ER AT U R E ( ° C )
FREQUENCY (Hz)

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE VERSUS LOAD RESISTANCE VOLTAGE VERSUS SUPPLY VOLTAGE

30 30
MAXIMUM PEAK-TO-PEAK OUTPUT

MAXIMUM PEAK-TO-PEAKOUTPUT

VCC = 15V RL = 10 kΩ
25 Tamb = +25°C 25
See Figure 2 Tamb = +25°C
20
VOLTAGE (V)

20
VOLTAGE (V)

15 15

10 10
5 5
0
0.1 0.2 0.4 0.7 1 2 4 7 10 0 2 4 6 8 10 12 14 16
LOAD RESISTANCE (k Ω) SUPPLY VOLTAGE ( V)

4/11
 TL084 - TL084A - TL084B

INPUT BIAS CURRENT VERSUS LARGE SIGNAL DIFFERENTIAL

FREE AIR TEMPERATURE VOLTAGE AMPLIFICATION VERSUS
FREE AIR TEMPERATURE

100
1000
V CC = 15V
400
INPUT BIAS CURRENT (nA)

10 200

DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 VO = 10V
4
2 R = 2k Ω
L

0.01 1
-75 -50 -25 0 25 50 75 100 125
-50 -25 0 25 50 75 100 125
TEMPERATURE (°C)
TEMPERATURE (°C)

LARGE SIGNAL DIFFERENTIAL TOTAL POWER DISSIPATION VERSUS

VOLTAGE AMPLIFICATION AND PHASE FREE AIR TEMPERATURE
SHIFT VERSUS FREQUENCY

250
DIFFERENTIAL VOLTAGE

225 V CC = 15V
TOTAL POWER DISSIPATION (mW)

100
AMPLIFICATION(V/V)

DIFFERENTIAL 180
200 No signal
VOLTAGE
PHASE SHIFT AMPLIFICATION 175 No load
(right s ca le ) (left s ca le)
150
10 90 125
R = 2kΩ 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125 C 25
0
100 1K 10K 100K 1M 10M -75 -50 -25 0 50 75 100 125
25
FREQUENCY (Hz)
TEMPERATURE (°C)

SUPPLY CURRENT PER AMPLIFIER SUPPLY CURRENT PER AMPLIFIER

VERSUS FREE AIR TEMPERATURE VERSUS SUPPLY VOLTAGE

2.0 2.0
SUPPLY CURRENT (mA)

1.8 V CC = 15V 1.8 Tamb = +25°C

1.6 No signal 1.6 No signal
SUPPLY CURRENT (mA)

1.4 No load 1.4 No load

1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
0.4 0.4
0.2 0.2
0 0
-75 -50 -25 0 25 50 75 100 125 2 4 6 8 10 12 14 16
TEMPERATURE (°C) SUPPLY VOLTAGE ( V)

5/11
TL084 - TL084A - TL084B

COMMON MODE REJECTION RATIO VOLTAGE FOLLOWER LARGE SIGNAL

VERSUS FREE AIR TEMPERATURE PULSE RESPONSE

INPUT AND OUTPUT VOLTAGES

89 6
R L = 1 0 kΩ
COMMON MODE MODE REJECTION

88
VC C =
4 OUTP UT
15V INPUT
87 2
RATIO (dB)

(V)
86 0
VCC = 15V
85 -2 R L = 2 kΩ
84 -4 C L= 100pF
Tam b = +25 C
83 -6
-75 -50 -25 0 25 50 75 100 125 0 0.5 1 1.5 2 2.5 3 3.5
TEMPERATURE (°C) TIME (µs )

OUTPUT VOLTAGE VERSUS EQUIVALENT INPUT NOISE VOLTAGE

ELAPSED TIME VERSUS FREQUENCY

28
70
24 VCC = 15V
OVERSHOOT 60
OUTPUT VOLTAGE (mV)

A V = 10
EQUIVALENT INPUT NOISE

20
R S = 100 Ω
90%
50
VOLTAGE (nV/VHz)

16 T amb = +25°C
40
12
30
8
V = 15V 20
CC
4 R L = 2k Ω
10%
0 10
Tamb = +25°C
t r
-4 0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 10 40 100 400 1k 4k 10k 40k 100k

TIME ( µs) FREQUENCY (Hz)

TOTAL HARMONIC DISTORTION VERSUS

FREQUENCY

1
V VCC = = 15V
15V
TOTAL HARMONIC DISTORTION

CC
0.4
V V= =
AA 11
VV
OO = 6V
(rms) = 6V
(rms)
0.1
T amb
T amb= =+25°C
+25°C
0.04
(%)

0.01

0.004

0.001
100 400 1k 4k 10k 40k 100k

FREQUENCY (Hz)

6/11
 TL084 - TL084A - TL084B

PARAMETER MEASUREMENT INFORMATION

Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k Ω

- 1k Ω
eI -
1/4
TL084 eo 1/4
TL084 eo

eI
CL = 100pF RL = 2kΩ
RL CL = 100pF

TYPICAL APPLICATIONS
AUDIO DISTRIBUTION AMPLIFIER

f O = 100kH z

1/4
Output A
1M Ω TL0 84

1/4 -
1 µF TL0 84
1/4
Input TL084
Output B

100k Ω 100kΩ
100k Ω
V CC+
1OO µF -
100k Ω
1/4
Output C
TL0 84

7/11
TL084 - TL084A - TL084B

TYPICAL APPLICATIONS (continued)

POSITIVE FEEDBACK BANDPASS FILTER

16 k Ω 16 k Ω

22 0p F 220pF

43k Ω 43 k Ω

43 k Ω 30 k Ω 43 k Ω 30 k Ω
Input - -

22 0pF 1/4 1/4 43 k Ω

- 22 0p F -
TL08 4 TL 08 4
43 k Ω 1/4 1/4
TL08 4 TL 084
Output B
1 .5 k Ω 1 .5 k Ω

Ground
Output A

OUTPUT A OUTPUT B

SECOND ORDER BANDPASS F ILT ER CASCADED BANDPASS F IL TER

fo = 100kHz ; Q = 30 ; Gain = 4 fo = 100kHz ; Q = 69 ; Gain = 16

8/11
 TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC DIP

Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
i 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100

9/11
TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA

14 PINS - PLASTIC MICROPACKAGE (SO)

Millimeters Inches
Dimensions
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.2 0.004 0.008
a2 1.6 0.063
b 0.35 0.46 0.014 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.020
o
c1 45 (typ.)
D 8.55 8.75 0.336 0.334
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.150 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.020 0.050
M 0.68 0.027
S 8 o (max.)

10/11
 TL084 - TL084A - TL084B

PACKAGE MECHANICAL DATA

14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 1.20 0.05
A1 0.05 0.15 0.01 0.006
A2 0.80 1.00 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.15
c 0.09 0.20 0.003 0.012
D 4.90 5.00 5.10 0.192 0.196 0.20
E 6.40 0.252
E1 4.30 4.40 4.50 0.169 0.173 0.177
e 0.65 0.025
k 0o 8o 0o 8o
l 0.50 0.60 0.75 0.09 0.0236 0.030

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifi-
cations mentioned in this pub lication are subject to change without notice. This publication supersedes and replaces all infor-
mation previously supplied. STMicroelectronics products are not authorized for use as critical components in life support
devices or systems without express written approval of STMicroelectronics.
 The ST log o is a trademark of STMicroelectronics

 1999 STMicroelectronics – Printed in Italy – All Rights Reserved

STMicroelectronics GROUP OF COMPANIES

Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco
The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.

 http://www.st.com

11/11