Scribd
Upload
108 views1 page

Page 005

This document summarizes an audio power wattmeter that measures power across an internal load. It has a range of 0-19.99 watts RMS with accuracies of +/- 1% and loads of 4, 8, or 16 ohms internally and calibrated for 8 ohms externally. The display is a 3.5 digit LED that shows power in watts with 0.01 watt resolution. It also has a scope adapter output that heterodynes RF signals below 1 MHz for analysis on an oscilloscope. Accessories include probes, leads, and optional items like a noise pulse simulator.

Uploaded by

docpot2008
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
108 views1 page

Page 005

This document summarizes an audio power wattmeter that measures power across an internal load. It has a range of 0-19.99 watts RMS with accuracies of +/- 1% and loads of 4, 8, or 16 ohms internally and calibrated for 8 ohms externally. The display is a 3.5 digit LED that shows power in watts with 0.01 watt resolution. It also has a scope adapter output that heterodynes RF signals below 1 MHz for analysis on an oscilloscope. Accessories include probes, leads, and optional items like a noise pulse simulator.

Uploaded by

docpot2008
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AUDIO POWER WATTMETER ACCESSORIES

METHOD: Peak-detecting,RMS-reading power of Included:39G102 Dynamic Mike Tester


sine wave acrossinternal load.
39c104 RF Cable Assembly (BNC/
RANGE: 0-19.99 Watts RMS. PL259)
ACCURACY: *bVo 39c105 Counter Probe ( isolated/direct)
LOADS: 39c106 Audio Lead Assembly (phone/
INTERNAL: 4, g, or 16 Ohms.1O Watts con-
test clips)
tinuous, 20 Watts for 30 seconds.
39c109 Audio Lead Assembly (phone/
EXTERNAL: Calibrated for 8 Ohms. min. phone)
DISPLAY: 3 t/2 digit, .01 Watts resolution, LED 39c110 RF Probe Assembly (50 Ohm
"WATTS"
indicator. Terminated)
SCOPE ADAPTER OI.JTPTIT
METHOD: HeterodynesRF signalto under 1MHz. OPTIONAL ACCESSORIES:
RF RANGE: 26.965-27.Sa00 MHz.
LOCAL OSCILLATOR: 26.92b MHz Approx.
OUTPUT VOLTAGE: .bV at 1 Watt RF.
RFS205 BF GhrnpororSuuitch connectsto
OUTPUT FREQUENCy: 40 WIz-480 KHz both the cB42 RF-|Fand 50-0hmload
(classD channels1-40).
jacks,and selects the propercablewith a
INPUT IMPEDANCE: b0 Ohms srvitch. Justa singleconnoction to the CB
SIGNAL TO NOISE SENSITIVITY TEST is all that is needed for simplified
CBper-
METHOD: Standard EIA 10 dB (S +N)/N test. formance t$ts of receiver sensitivity
andall
Audio Power Wattmeter sensitivity is increased
transmitter outputs. $25.00
l0dB for Noise Reference.
GENERAL:
FUSE: 1.A'Fast-blow, type 3AG
ELECTRICAL: All solid state circuitry, including
IIt204 EIA JloisePulseSimulatorsimulates
CMOS LSI.
ignition noise for testingthe Automatic
MECHANICAL: Vinyl-clad steel with aluminum
Noise Limiter (ANL) and NoiseBlanker
trim. Carrying handle. Lead storagecomparrmenr (NBl circuitsin someCBs
in back of case. $25.00
SIZE: 11" x 14" x 11" (HWD). (28cmx 3b.bcmx
28cm).
WEIGHT: 24 lb. (10.9Ks).
POWER: 105-130VAC, b0/60 Hz. tb W: or t2 Available through Sencore distributors or Service
VDC, 1A. 220 VAC modification availabieat
extra cost. f3fts D_epartment,
Sen_core,Inc.,
8200 SencoreDrive,
SiouxFalls,SD 57LO7.

You might also like