Scribd
Upload
198 views3 pages

EZVeneer Bracelet

These bracelets require little time or materials to make and are ideal gifts. The instructions involve purchasing veneer and inlay banding, making a bracelet form from pine, cutting the veneer into strips, soaking the strips to make them pliable, wrapping them around the form, gluing and clamping them, sanding smooth, and applying a clear finish. The entire process is detailed in 15 steps.

Uploaded by

BSulli
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
198 views3 pages

EZVeneer Bracelet

These bracelets require little time or materials to make and are ideal gifts. The instructions involve purchasing veneer and inlay banding, making a bracelet form from pine, cutting the veneer into strips, soaking the strips to make them pliable, wrapping them around the form, gluing and clamping them, sanding smooth, and applying a clear finish. The entire process is detailed in 15 steps.

Uploaded by

BSulli
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Project 16458EZ:

Veneer Bracelets

These lovely bracelets require little time or materials –


two features that many woodworkers look for when select-
ing a project. The also make ideal gifts for friends and
relatives, or to sell at gift shops and craft fairs.
Veneer Bracelets Step-by-Step Instructions
Step 1: Purchase Veneer and Inlay Banding
1. Purchase enough 1/32" thick veneer to make each bracelet desired. NOTE: When
selecting veneer, it’s best to stick with a stock that’s straightgrained. Burl and
crotch stock are likely to split when bent, so avoid them.
2. Purchase inlay banding for bracelets that you would prefer to have this replace the
outer strip of veneer.

Step 2: Make the Bracelet Form


1. Face-glue two pieces of 3/4" thick by 3-1/2" square pine.
2. Scribe the appropriate profile from the full-size pattern. NOTE: The profiles
shown serve only as a guide, so you may want to make yours bigger or
smaller. Use a band or saber saw to cut out the profile.
3. Sand the profile smooth.

Step 3: Make the Bracelet


1. Select a suitable piece or suitable pieces of veneer for each bracelet.
2. Use a veneer saw or sharp razor knife to cut each piece (with the grain running
lengthwise) to the desired width. NOTE: Be sure the veneer doesn’t overlap
when bent around the form.
3. Bring a pan of water to a boil.
4. Remove the water from the heat.
5. Soak the strips in the hot water until pliable (5-10 minutes). NOTE: DO NOT
soak the inlay strips for more than 5 minutes or the small pieces may begin to
separate.
6. Remove the strips from the water.
7. Wrap the strips around the form.
8. Secure the strips in place with a web clamp or masking tape
9. Allow the strips to dry overnight.
10. Remove the strips from the form and apply glue. Be sure to cover the surfaces
thoroughly.
11. Apply a coat of paste wax to the form to keep the veneer from adhering to the
form.
12. Reassemble the strips and secure with the web clamp or masking tape.
13. Allow to dry at least two hours.
14. Use sandpaper to sand all surfaces smooth, particularly the edges and the ends.
15. Apply Deft’s clear semi-gloss interior finish for an attractive final finish. Dip the
bracelets into the finish by fastening string to them with thumbtacks.

These plans were originally published in Volume 8, Issue 1 of The Woodworker’s Jour-
nal (Jan./Feb. 1984, pages 46-47).

You might also like