Scribd
Upload
61 views

Non-Monitored or Simple: VLF Withstand Test

VLF non-monitored or simple withstand testing involves applying a predetermined voltage at a very low frequency, such as 0.1-0.01 Hz, for a set period of time. If the test object survives, it passes. This type of testing requires much less power than high frequency testing because very low frequencies produce much higher capacitive reactance in cables and equipment. As a result, VLF testing can evaluate much longer cable circuits than high frequency testing and helps minimize failures during actual system operation.

Uploaded by

DenisTaras
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
61 views

Non-Monitored or Simple: VLF Withstand Test

VLF non-monitored or simple withstand testing involves applying a predetermined voltage at a very low frequency, such as 0.1-0.01 Hz, for a set period of time. If the test object survives, it passes. This type of testing requires much less power than high frequency testing because very low frequencies produce much higher capacitive reactance in cables and equipment. As a result, VLF testing can evaluate much longer cable circuits than high frequency testing and helps minimize failures during actual system operation.

Uploaded by

DenisTaras
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

VLF non-monitored or simple withstand test

Brought to you by Bruce Olson

non-monitored or simple withstand test


A test in which a voltage of a predetermined magnitude is applied for a predetermined time. If the test object survives the test it is deemed to have passed the test. (IEEE 400.2/D10)

Objective

Minimize In Service

System Failure

WHAT IS VLF?
A VLF instrument is an AC hipot but with an output frequency other than 50/60 Hz. Very Low Frequency: 0.1 Hz and lower. By decreasing the frequency, it is possible to test miles of cable with a small and affordable unit.

Models range from 0.1 0.01 Hz.

VLF Explained
Xc = 1 2 x pi x f x C
The lower the frequency, the higher Xc (capacitive reactance). The higher Xc (or resistance across the power supply output), the lower the current/power needed to apply a desired voltage.

At 0.1 Hz, it takes 600 times less power to test a cable, or any other high capacitance load, than at 60 Hz. At 0.01 Hz, 6000 times higher capacitive loads can be tested than at 60 Hz.

60 Hz vs. 0.1 Hz
At 60 Hz. a 1 F cable has an Xc of 2.65 kOhms. At 22 kV, it requires 8.3 amps of current to test. Total power supply rating must be 183 kVA. At 0.1 Hz, the Xc is 1.59 megohms. At 22 kV, the current needed is 14 mA. Total supply power needed is .304 kVA.
(22 kV is the maintenance test voltage for 15 kV cable)

VLF Withstand Test Advantages


Minimal Training IEEE 400.2 Interpretation

VLF Withstand Disadvantages?


Not exactly operating voltage frequency Longer Circuits require lower voltages or frequency

Test Parameters / Data Collected


Voltage 1.5 3 x Uo

Frequency
0.1 0.01 Hz Time

15-60 Minutes

System Passes Test


DO NOTHING

90% survive in Service for at least 5 years after the test (IEEE 400.2/D10)

System Fails Test

Decisions
Repair or Replace

Cable systems that fail on test and are then repaired and retested have a survival rate >95% (IEEE 400.2/D10)

VLF WITHSTAND
Low Cost to implement Easy to interpret Increases Reliability

You might also like