Scribd
Upload
52 views1 page

Wood Beam: Material Properties

This document summarizes the structural analysis of a wood beam with a span of 8 feet. The beam is made of Douglas Fir-Larch grade No. 1. Uniform and varying uniform loads were applied representing roof and wall loads. Point loads were also applied. The maximum bending stress was calculated to be 34.08 psi, well below the allowable stress of 1,345.87 psi. The maximum shear stress was 7.24 psi, below the allowable of 512.2 psi. Deflections were all well below limits. The beam was determined to be structurally sufficient.

Uploaded by

Noel Guades
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
52 views1 page

Wood Beam: Material Properties

This document summarizes the structural analysis of a wood beam with a span of 8 feet. The beam is made of Douglas Fir-Larch grade No. 1. Uniform and varying uniform loads were applied representing roof and wall loads. Point loads were also applied. The maximum bending stress was calculated to be 34.08 psi, well below the allowable stress of 1,345.87 psi. The maximum shear stress was 7.24 psi, below the allowable of 512.2 psi. Deflections were all well below limits. The beam was determined to be structurally sufficient.

Uploaded by

Noel Guades
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Wood Beam

ENERCALC, INC. 1983-2011, Build:6.11.6.23, Ver:6.11.6.23


Licensee : Lic. # :
File: P:\7) Boccella Residence\Calculations\Enercalc\ROOF BEAMS.ec6
Description : RB16 CB
Material Properties
Beam Bracing :
Calculations per NDS 2005, IBC 2009, CBC 2010, ASCE 7-05
Completely Unbraced
Allowable Stress Design
Douglas Fir - Larch
No.1
1,350.0
1,350.0
925.0
625.0
1,600.0
580.0
170.0
675.0 32.210
Analysis Method :
Eminbend - xx ksi
Wood Species :
Wood Grade :
Fb - Tension
psi
psi
Fv psi
Fb - Compr
Ft psi
Fc - Prll psi
psi Fc - Perp
E : Modulus of Elasticity
Ebend- xx ksi
Density pcf
Load Combination :2009 IBC & ASCE 7-05
6x10
Span =8.0 ft
D(0.36) Lr(0.45)
D(0.028) Lr(0.04)
D(0.12)
D(0,0.056) Lr(0,0.08)
D(0.056,0) Lr(0.08,0)
Applied Loads
Service loads entered. Load Factors will be applied for calculations.
Beam self weight calculated and added to loads
Uniform Load : D = 0.0140, Lr = 0.020 ksf, Tributary Width = 2.0->0.0 ft, (ROOF)
Uniform Load : D = 0.0150 ksf, Tributary Width = 8.0->0.0 ft, (WALL ABOVE)
Varying Uniform Load : D(S,E) = 0.0->0.0140 ksf, Extent = 0.0 -->> 4.0 ft, Trib Width = 4.0->0.0 ft, (HIGHER ROOF)
Varying Uniform Load : D(S,E) = 0.0140->0.0, Lr(S,E) = 0.020->0.0 ksf, Extent = 4.0 -->> 8.0 ft, Trib Width = 4.0->0.0 ft, (HIGHER ROOF)
Point Load : D = 0.360, Lr = 0.450 k @4.0 ft, (FR RB15-RIGHT)
DESIGN SUMMARY Design OK
Maximum Bending Stress Ratio 0.381: 1
Load Combination +D+0.750Lr+0.750L+H
Span # where maximum occurs Span # 1
Location of maximum on span 4.000ft
34.08psi =
=
FB : Allowable 1,345.87psi Fv : Allowable
6x10
Section used for this span
Span # where maximum occurs
Location of maximum on span
Span # 1 =
Load Combination +D+0.750Lr+0.750L+H
=
=
=
170.00psi = =
Section used for this span
6x10
fb : Actual
Maximum Shear Stress Ratio 0.200 : 1
7.240ft =
=
512.20psi fv : Actual
Maximum Deflection
0 <240
1448
Ratio = 0 <180
Max Downward L+Lr+S Deflection 0.027 in 3586 Ratio =
Max Upward L+Lr+S Deflection 0.000 in
Ratio =
Max Downward Total Deflection 0.066 in
Ratio =
Max Upward Total Deflection 0.000 in
Location in Span Load Combination Max. "-" Defl Location in Span Load Combination Span Max. "+" Defl
Overall Maximum Deflections - Unfactored Loads
D+Lr 1 0.0663 4.040 0.0000 0.000
Load Combination Support 1 Support 2
Vertical Reactions - Unfactored
Support notation : Far left is #1 Values in KIPS
Overall MAXimum 1.476 1.476
D Only 0.931 0.931
Lr Only 0.545 0.545
D+Lr 1.476 1.476

You might also like