Scribd
Upload
114 views2 pages

MML Commands

This document provides a summary of 27 My MML Command functions for configuring and monitoring network equipment, including restarting systems and units, checking restart status, setting recovery bans, listing connected base stations and transmitters, configuring channels and frequencies, locking and unlocking transmitters and channels, and configuring GPRS parameters.

Uploaded by

Tanya Zhitnik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
114 views2 pages

MML Commands

This document provides a summary of 27 My MML Command functions for configuring and monitoring network equipment, including restarting systems and units, checking restart status, setting recovery bans, listing connected base stations and transmitters, configuring channels and frequencies, locking and unlocking transmitters and channels, and configuring GPRS parameters.

Uploaded by

Tanya Zhitnik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Mml Commands

My MML Command Summary


0 To know ip addresses ZQRI
1. System Restart
ZUSS:SYM:C=DSK,;
2. Unit Restart
ZUSU:BCSU,0:C=DSK,;
3. Check Restart Status
ZUSI:COMP:;
4. Set Recovery Ban, RBAN(If this is set, in case of crash, the system will not restart..recovery is banned)
ZUST:BCSU,0:S-RBAN
5. Clear Recovery Ban
ZUST:BCSU,0:C-RBAN
6. List of all BTSs, BCFs and TRXs connected to the BSC.
ZEEI;
7. List of all BTSs and TRXs in BCF
ZEEI: BCF=x:;
8. List of the BCF and the TRXs attached to BTS
ZEEI: BTS=x:;
9. Channels configured in a TRX under a BTS
ZERO: BTS=x: TRX=y:;
10. Channels configured for all the TRXs in a BTS
ZERO: BTS=x:,
11. Locking of TRXs
ZERS: BTS=x: TRX=y:L:;
12. Un Locking of TRXs
ZERS: BTS=x: TRX=y:U:;
13. Locking of Channels
ZERS: BTS=x: TRX=y: CH=2&&4:L:;
14. Unlocking of Channels
ZERS: BTS=x: TRX=y: CH=2&&4:U:;
15. Frequency
ZEEI: BTS=x:;
16. BAND..List all parameters of BTS
ZEQO:BTS=x:;
17. BTS Locking
ZEQS:BTS=x:L:;
18. BTS UnLocking
ZEQS:BTS=x:U:;
19. To check frequency hopping parameter(BTS HOPPING MODE)
ZEQO: BTS=x: HOP
20. To set the frequency hopping parameter
ZEQE: BTS=x:HOP=Y/N;

21. Coding Scheme(MCA, MCU), MEAN BEP, BLER..ALL GPRS params of BTS.
ZEQO: BTS=x: GPRS:; ZEQV: BTS=x: MCA=y:;...ZEQV: BTS=x: MCU=y:;
22. GENA/ EGENA status and setting
ZEQO: BTS=x: GPRS:;(for status)....ZEQV:BTS=x: GENA=N/Y:; ZEQV:BTS=x: EGENA=N/Y
23. NSEI, BVCI
ZEQO: BTS=x: GPRS:;
24. CDED, CDEF, CMAX(dedicated, default, maximum GPRS capacity)
ZEQO: BTS=x: GPRS:; ZEQV: BTS=x: CDED=a: CDEF=b: CMAX=c:; (Do GENA N/Y while changing CDED etc)
25. LA status(ELA)
ZEQO: BTS=x: GPRS:; ZEQV: BTS=x: ALA=Y/N:;
26. C/I Ratio
ZEQO: BTS=x: GPRS:;
27. DCSA, DCSU, UCSA, UCSU(Uplink/ Downlink CS in Ack Unack mode)
ZEQO: BTS=x: GPRS:; ZEQV: BTS=x: DCSA=a: DCSU=b: UCSA=c: UCSD=d:;

You might also like