I D G a rd RFID/DIGITAL ACCESS CONTROL KEYPAD __IDG-BC8110 INSTALLATION AND OPERATION INSTRUCTIONS + Mult Funetions + Backit Keypad + 3-Operation Mode: FEATURES AND FUNCTIONS c€e RoHS COMPLIANT Door Left Open Too Long Warning Output Activation Announcer PPactier Tone Inhibit Control, Audible or Stent Operation Keypad Blocking or Alarming ater 3-10 False Enties Tamper Beep ON/OFF Selectable ‘Alarming Output and Temper Waming Output Egress Input fr Door-open Remote Triggering Doorbell Button Keypad Programmable Non-volatile Memory in Power Falture Features N.O. and N.C. Dry Contacts, Max Rating of Contact Current 20/24VDC User Card Operation, User Code Operation, : User Card + User ID Number Operation +1 Relay Output , + 500 Users : + Operates Fail-safe or Fail-secure Electic Locks + Auto Code Entry or Manual Code Entry Checking i + Door Forced Open Warning ‘ 2. SPECIFICATIONS Operating Voltage savpe ‘Current Drain Quiescent Stato =31mA, ‘Aclve State =52mA Relay Output Contacts Capacity of Recorting Total 600 User Cards andlor User Codes Card Reading Distance Max Distance 10 OM ‘Type of ID Card EM Card 126 KHZ Dimension 112 (H) nm x 84 W) mm x 26 (0) mm Weight ‘1109 3. AUDIBLE AND VISIBLE INDICATIONS Datnion satus ‘Ourpat uae ‘Audible and Visible Indleator Indicator Indicator Indications Amber LED ‘Groen LED Buzzer ‘STATUS PASS Sandy made 1 Flash in 2 Seo nional ‘Successful koy ony “Flash then ligt for 10 Seo Beep ‘Successful cardlcode arty Flashes Tight 2 Beeps. ‘Successful operation. 72 Flashes Beeps Unsucossefl card code enity Sashes, ‘5 Beeps. Unsuccessful operation 3 Flashes: 3 Beeps: Tn blocking status 1 Flash in 10 Sac tonal 1 Short be=p in 10 Sec terval (No response to card / code entry) 4 Long beep fish blocking In programming moce, Tight Tight During programming bight ‘Continuous Flash CConfimation of programing ght ight Beeps (PRESS KEY #) ‘Alarming statis ‘Continuous fash ‘Coninaous DOOD Notice touser: (1). Successful key entry it wl keep 10 seconds, no further key entry In 10 seconds, wil retum to normal operation status (Standby mode), (2) incase of wrong key eniry, cancel he wrong etry by pressing key #, or wating fr 10 seconds thon ro-otor. 4, PROGRAMMING Before use of the new accass cortrel Keypad, programming every item to confim the functions and seins meet the requirement of the users Programming Code = Management Code = Master Code Default Programming Code is 1234 Note: (1) Successful programming operation ~ The amber LED wi show 2 fash athe buzzer wl sound 2 beeps. Unsuccessful programming operation ~ The amber LED wil show 5 flash and the buzor wil sound 5 beops, (2) Tho Usor Card / User Code / Usor IO Number are not alowed to record repestedy. Repeat record wil not be and wi {ve warning signa. anbor LED § flash, Buzz sound § beop fo igi rejection, Is requited to delete the olddata then Feenter te non dat, PROCEDURES OF PROGRAMMING (1) Entry into programming PRESSKEY x ~Enlerthe programing cose 8 is coat code i 254)» # (The amber LED and green LED hid, stoning ony programing mos)@ 8) “ ©) © a Recording the new programming code (This procedure must be done! Warning: For security purpose, the owner should change the default programming code (1234) to ‘owner's private programming code (=Master Code) before use of the new access control keypad. PRESS KEY 0+ Enter he new programming code (48 dis) > Recording the User Card / or the User Code «When recontng the User Card ofthe User Code, should note ifthe recording is successful andthe indeations amber LED show 2 flash ane buzzor sound 2 beeps, signing accoptance of te entry. + Assign a numberof any 4 igs asthe User ID Numbor for each User Card or User Code, the UserID Num tse nthe programming Keop the UserID Number as an entation of an user + One User 10 Number is only for one User Card or one User Code, do not use the same User ID Number for recording both the User Card and the User Code, otherwise the lator one cannot enter for recording! A. Recording the User Card PRESSKEY 1 + Enter the User Number (4 cigs) -» Read the User Card — Note: if continue to record more User Cards, atthe end of each recording, itis no necessary to press key # per ‘each time, to repeat above steps until all User Cards recordings are finished. Finally to press the key # 10 ‘confirm ail recordings are completed. IMPORTANT NOTE : The 4igital Usor 1D Number for User Card isto be used in Operation mode. B. Recording the User Code PRESS KEY 1 — Enlorthe Usec ID Number (4 dgs)-» Enter the User Code ~ # (Confirmed code length) (Green LED fashing) = # (Green LED stop flashing), (Contmed entering completed) Note: If continue to record more User Codes, at the end of each recording, It sno necessary to press key # of the ‘second time, to repeat above steps until all User Codes recordings are finished. Finally to pros the key # to ‘confirm all recordings are completed. Deleting the User Card / or User Code A. PRESSKEY 2 0000 ~# (Deleted all User Cards or all User Codes ) 1B. PRESSKEY 21 Read ho User Card or Enor tho User Cade tobe deleted # (elated the Read User Card or the Enered Usor Code) C. PRESSKEY 22+ Enter the UserID Numbarof he User Card or the User Code -+# (Deleted tho Usor Card or User Code of the User iD Number) Programming the open-door mode A. PRESSKEY 3 00~-# (Open door by User Card /or Open door by User Code ) 1B. PRESSKEY 3+ 01+# (Open door by User Card + UserID Number) Note: Factory sting “Open door by User Card or User Code’ Programming the door open time and relay output mode |. PRESSKEY 40> (01-99 seconds) + # (Output Relay seting 1-89 seconds momentary modo) 3, PRESSKEY 41 --# (Output Relay setting latch mode) (Latch Mode = Toggle Mode) Note: Factory soting "3 soconds momentary mode” Programming ~ Function Settings A. User Code entry mode I) MANUAL checking code entry mode PRESSKEY 70-10-+# (Manual airy mode, have to press key # folowing the Usor Code entered to conf the code Tength ofthe User Code erred, The User Code can be 4-8 dts) 1) AUTO checking code entry mode PRESSKEY 70-+1-+# (Aulo entry mode, the Usor Code must beset inthe same code length as the programming code. ‘No neod to PRESS KEY = o confi the code length ofthe User Cade entores. The User Code can bo 4-8 digits) Note : Factory setting “Manual checking code entry mode! B. Output relay activated announcer 1D) PRESSKEY 710-# (Announcers disabled) i) PRESSKEY 71-11-+# (Buzzer sounds fr 1 second time to incicato output relay is activated) Note : Factory setting “Announcer disebled” ©. Pacifier tone 1) PRESSKEY 72-+0-+# (Pacifortone prohibited, sient curing operation) 1) PRESSKEY 72-1-+# (Paciortone avaietle) Note: Factory setting ‘Pacifier tone avaliable” D. Door force-open alarm (To be operated with magnetic door switch installed) PRESSKEY 73-+0-+# (Door force-open alarm is dsabied) ) PRESSKEY 73-+1-—# (Door force-open alarm i enabad) Note: Factory stting “Door Force-open alarm is disabled” E. Programming the alarm time PRESSKEY 74 (01-99 minutes)-+# (Alarm timo soting 1-99 minutes) Note: Factory setting “Alarm time 1 minute” rat allowed to repoat !sor Card + Usor 1D Number”(®) Programming the safety functions A. PRESSKEY 8 —+00-# (Gaety function is csabied) B. PRESSKEY @ —01—# (Alarming - ALM OUT switches to ground after 10 entries of invalit User Card or 10 ‘entries of false code, or 1 entry of vais User Gard than 5 enties of false User ‘Number. Alarming can be released by reading valid User Car, or entering Usor ‘Code oF Usor Card * User ID Number, depends on programming ofthe mode) ©. PRESSKEY 81 (03-1Dentis)—~ (Selectable of ae 3-10 entries of iva User Crd of 10 ents of ite cade, %+1.(01-00 minutes)» # ‘ort erty of vate User Card +S ents of false UserID Number, he conta talon books for 39 minutes. Blcking can be released by eadng val User Car, or tenting User Code or User Cad UserID Numb, depends on he breeraming te mode) Note: Factory Setting “After 10 entries of invalid User Card or 10 entries of false code, of 1 entry of valid Usor Card + Sentres of false User ID Number, the access control keypad blocks for 1 minute” ‘Acooss Control Keypad in blocking state : 'No respons to invalié Car or Key ont, amber LED howe 1 flash and buszereaunds 1 short boop in 10 second intra the end ‘of blocking tho buzzor sounds 1 long boop fo sign ho ond of blocking and return to normal operation mode (9) Door state monitoring (To be operated with magnotic door switch installed) A. PRESSKEY 9 —00—# (The monitring function is sabes) B, PRESSKEY 9 (01-99 seoonds) > # (The monitoring function fs enabled) ‘The function has 2 performance : |) the doors eft open longer than pre-sting of door open tims (1-99 seconds) and forget to close the door the buzzer wil ‘beep continuous fo remind the usr to close the door: Tha buzzer wil sop beep ater te door closed |) Incase of door is force-cpened, he buzzer wll bop as alarming signal closing the door can not sop alarming, should read ‘ald User Card, or ener User Cade, or User Card» Usar ID Number depends on the programming of te ope-door mode, {0 sop alarming Note : Factory Setting “The monitoring function I disabled” (10) End of Programming Aor completing a programming procedures, ext programing mode in 60 soconds PRESSKEY To xt programming mode and return to nermal operation status (Standby mode), OPERATION OF THE ACCESS CONTROL KEYPAD Note : The amber LED 1 flash in 2 socond interval - the access control Keypad Is in normal operation mode, standby for use. (1) Open door by User Card (Door opened by reading User Card) (2) Open door by User Code (Door opened by entering User Code ) (@) Open door by User Car « User ID Number (Door opened by reacing User Car, groan LED wl ash, In 10 seconds entering the User 1D Number (NOTE: During the period of the Green LED Flashing It can be returned to normal operation status-standby mode by pressing the key ») (4) many case, the programming code can open the door, operation as folows Enlor programming code #> 1 (For manual code entry mode) Entor progremming code--1 (For auto cose enty mode) SAFETY FUNCTIONS (1) The access conzo keypad automaticaly blocks or slams sor 310 abnormal enites, (2) The access contro keypad alarms when the doo is foree-opanod (@) The access conto keypad alas I the door sl open Inger than the pre-sting of door open me, o remind the user to close the oor (4) Incase of tho tampor snitch is activated, the control station can send warning signals: The ember LED continuous flashes, the buzzer Continuous beeps, Alarm out function i also tiggere, unl tamper swich i deactivated. (©) "NMOUT (ALARM OUT) canbe comet indoor our Kt and sound wring skal dv, or cometary alam syst RESTORING THE DEFAULT PROGRAMMING CODE "tthe programing code i ost (or unknown), use the DPC jumper to restore the detaut programming code, procedures as follows (1) Disconnect power supply (2) Putte DPC jumper from OFF poston to ON poston. (@) Reconnect power supply, the amber LED wl fash constantly an the buzzer wll beep constantly, (4) Putte DPC jumper back to OFF positon, amber LED wil sop ashing, buzzor wil stop boop, (8) The default programming code 1234 ie restore, Noto: “The ratoring operations only restore the default propramming code 1234, the recorded Data or Setings wil not be changed or dloted 8 NOTICE TO INSTALLER (1) Around the access cont keypad In 50 CM distance, thre must be no any appertus with 100 KHZ-150 KHZ frequency sources (inorder that no interference fs appeares), (2) Inte instalation, te distance of2 access cotrel keypad, or one acess contol keypad and other card readers, shoud ove 50 OM, (@)_ For safety purpose, the power supply for the Access Control Keypad must provide over current protection device such as a Fuse Thana ut of Amp cure ning. Arad sees cones eve habe norporated xtra tothe (4) Donot connect wires with power ON. Before apply power to the contol station should confi power voltage s 12V DC and the potty Gs oreWIRING DIAGRAM IMPORTANT NOTICE TO INSTALLER: (1) To prevent he electromagnetic interference from the oporation of the electric lack device, must connect one IN4OOT diode fo the power {ermnials of tho DC operated electri locks, or connect one MOV (T8V) 10 the power terminals ofthe ACIDC operated electric locks. 2) the door sensing function i natin use (he magnetic door stch snot installed), must connect the "Door Sens” wie (Green colour wre) {a;GND (Black colour wire), making the sense wire and GND in closed cc. (1) The Access Control Keypad controls the apparatus Via External Power Supply as. = (2) The Access Controt Keypad directly controls the connecting apparatus (Mote: Max Rating of Relay Contact Current 2A/24VDC) owen surecy pes Td | ne] 3) He swoscene_aorseae.e3