Blue ESR Meter Kit

Assembly, Use &

Troubleshooting Manual
Bob Parker designed the Blue ESR meter supplied by

AnaTek Corporation
100 Merrimack Road, P. O. Box 1200
Amherst, NH 03031 USA

603.321.0884, FAX 603.836.4436, [email protected]

Forget about capacitance meters - an ESR meter is the way to go when it comes to identifying faulty
electrolytics. This well-proven design is auto-ranging, low cost and simple to build.

• In-circuit testing, made possible by using <100mV test voltage

which does not forward bias diodes or transistors.
• Auto-ranging to cover 0.01-99Ω.
• Non-polarized test leads due to no DC component in the test
signal.
• Single pushbutton to easily control all functions.
• Automatic switch-off after three minutes when the meter is idle.
• Low battery voltage warning - “b” blinks on the display.
• 3mm LED displays for easy viewing from a distance.
• Chart of typical electrolytic capacitor ESR figures on the front
panel.
• Built in self test
• Integral test leads

This document was written by Bob Parker and edited by John Bachman at AnaTek Corporation. Some graphics
and text courtesy of Silicon Chip March/April issue 2004.
 Parts List and Assembly Order
PC board 47K (R4), 4 2.2K (R5, 7. 9, 4 pieces 5 position inline 2 3/8” rubber grommets
15) header strip
1% MF Resistors 6 10K (R1,19,20,21,23,24) Semiconductors 2 test leads, banana plugs and
alligator clips
100R (R10) Miniature pushbutton switch 4 1N4148 or 1N914 signal 3” tie wrap
with cap diodes (D1, D2, D5, D6)
470K (R22) 10kΩ PC-mount trim pot 2 1N4004, 5, 6 or 7 power Miscellaneous
(VR1) diodes (D3,D4)
10.0K (R6) 220Ω PC-mount trim pot 7 2N3906 PNP transistors ESR chart label
(VR2) (Q1, Q3, Q4, Q5, Q8, Q9,
Q10)
1.0K (R8) 3.58MHz crystal resonator 6 2N3904 NPN transistors contact information label
with internal capacitors (Q2. Q6, Q7, Q11, Q12, Q13)
5% Resistors Capacitors LP2950CZ-5.0 3-terminal plastic enclosure with battery
regulator low-dropout (IC1) lead and hardware
Some are marked 78MCYFE
KY5050
220R (R11) 3 100µF 16V RB electrolytic Z86E0412 programmed 6 #2 self tapping screws
(C1, C3, C9) microcontroller (IC2)
1K (R12), 100K (R13) 22uf, 33uf or 47µF 50V 4094 / MC14094 CMOS
bipolar RB electrolytic (C6) shift
register (IC3)
220K (R14), 180R (R16) 22µF 16/25V RB electrolytic 2 LTS-5503AB 7-segment 82.0R for alignment
(C8) displays (DIS1, 2)
6.8K (R17), 680R (R18) 470nF 63V MKT (C10) 2 3mm blue LEDs (LED1,2) 5R6 for alignment
3 4.7K (R2, 27, 28) 3 100nF 50V disc or
multilayer (C4,C5,C13)
27K (R25), 2.7K (R29) 33nF 63/100WV (C7)
2 15K (R3, 26), 100R (R30) 10uf 16/25WV electrolytic
(C2)
Resistor Color Codes
Value 4-Band Code (5%) 5-Band Code (1%)
5.60 Ω green blue gold brown green blue black silver brown
82 Ω grey red black brown grey red black gold brown
100 Ω brown black brown brown brown black black black brown
180 Ω brown grey brown brown brown grey black black brown
220 Ω red red brown brown red red black black brown
680 Ω blue grey brown brown blue grey black black brown
1k Ω brown black red brown brown black black brown brown
2.2k Ω red red red brown red red black brown brown
2.7k Ω red violet red brown red violet black brown brown
4.7k Ω yellow violet red brown yellow violet black brown brown
6.8k Ω blue grey red brown blue grey black brown brown
10k Ω brown black orange brown brown black black red brown
15k Ω brown green orange brown brown green black red brown
27k Ω red violet orange brown red violet black red brown
47k Ω yellow violet orange brown yellow violet black red brown
100k Ω brown black yellow brown brown black black orange brown
220k Ω red red yellow brown red red black orange brown
470k Ω yellow violet yellow brown yellow violet black orange brown
Construction
Even if the ESR Meter’s
operation seems
complicated, at least it is
easy to build. As you can
see in the photos, all the
components are mounted
on a single PC board
which is then attached to
the enclosure bottom.

Even though the pc

board is high-quality with
solder-mask it is still wise
to check it for defects.
To do this, illuminate the
component side with a
bright light and examine
the copper side very
carefully – preferably with
a magnifier – for any
hairline fractures in the
tracks.

During assembly
frequently check for any
solder “whiskers” or
bridges and pay particular
attention to any tracks,
which pass between IC
pads, where such defects
tend to congregate and
hide. It is good practice
to install 5 or 6
components and then
check the soldering of
them under a magnifier.
Then move on and install
5 or 6 more.

The PC board is tightly

packed and the solder
pads are quite small so be
very careful with your
soldering. Always lift the
iron vertically from a just
soldered joint and never
wipe it sideways as so
many constructors seem
to do!
Component Installation Sequence
The kit package contains six plastic bags of components and one bag of static sensitive components. Install them in
the following order:
1% resistors
5% resistors
Semiconductors (Do not install the decimal LEDs until after installing the 7-segment displays. See Install
LED Displays.)
Capacitors
Miscellaneous parts
Static Sensitive components (Do not install the integrated circuits until after performing the Initial
Checks.)
The bag labeled “For alignment and test” contains two resistors that are used for that purpose and are not installed
on the pc board.
Installing components
The construction sequence basically installs the smallest components first. It is notoriously difficult to correctly
identify the color bands on 1% resistors so check each one’s value with an ohmmeter before soldering it to the
board. The table of color codes above will help you select the resistor values prior to checking.
It is a good idea to check the value of all of the resistors with an ohm meter as manufacturers occasionally make
labeling mistakes.

Take care with the orientation of the polarized components: the electrolytic capacitors, diodes, and transistors. You
should also make sure that the two different transistor types go into their correct places.

Note that there is provision on the pc board for two 27 pf capacitors near the crystal. Your kit has a crystal
resonator with internal capacitors supplied so that those two components are not needed.
After you have the small parts installed and soldered into place you can install the larger components. These parts
include crystal XTAL1, the electrolytic capacitors, trim-pots VR1 & VR2, the transistors, and the headers for the
LED displays.

Note particularly that the 7-segment LED displays are each mounted on two 5 pin headers which are soldered to
the pc board (see picture below). Make sure that the headers are absolutely vertical and flush with the pc board
before soldering the pins so that the displays will fit properly under the enclosure cover. If you prefer, you can
carefully push the headers onto the 7-segment displays and then solder them to the pc board. That method assures
proper alignment but make sure that the headers sit snugly onto the pc board surface. Make sure that the ‘dot’ on
the 7-segment displays are at the bottom.

OPTION: Some kit builders are nervous about soldering directly to the integrated circuit pins and prefer to install
sockets for that reason. We have included sockets so that you are free to use them if you wish.
 Strip and tin the one end of
the test lead ends. Put the two
grommets into the test lead
holes in the enclosure end
panel. Then feed the test
leads through the grommets.
The outside of the panel is the
finished side.
Miscellaneous parts – see text
for display header installation.
The headers must be installed
carefully to ensure proper
alignment of the 7-segment
displays.

Test lead connection. Note

the tie wrap retainer.
 Test lead installation
Strip approximately 1/8” (2 mm) from one end of the test leads and tin using rosin core solder. Install the
grommets into the enclosure end panel as shown in the picture. Then push the test leads through the grommets.
The outside of the panel is the finished side
Then solder the test leads to the pc board and secure them with the
tie wrap. Leave enough slack for the leads to clear around the pc
board holes for the enclosure bosses.
Strip approximately 1/2” (12 mm) from the other end of the test
leads, do not tin them but bend the bare wire back on itself. Push
the banana plug insulators onto the leads first and then push the
bare wire end into the center hole of the banana jacks so that it is
lined up with the securing screw as shown in the picture on the left.
Slide the insulator over the banana plug and screw the retaining
screw in tightly.
Banana Plug assembly

Install LED displays

If you did not install the headers onto the 7-segment displays before soldering them to the pc board you must do so
now. Otherwise, skip this step, you already did it!
Before handling the 7-segment displays make sure that you are grounded as they are sensitive to static electricity.
Orient the 7-segment displays with their decimal points toward the bottom of the pc board (battery connection end)
and push the pins into headers making sure that they are fully seated.
Then insert the two decimal point LEDs such that the tops of the
LEDs are the same height as the 7-segment displays. Make sure that
they are correctly oriented; ie, the shorter lead must go toward the 7-
segment displays. The top of the decimal LEDs should be flush with
the top of the 7-segment displays.

Once all of the components are installed on the PC board, hold the
component side up to a bright light and carefully check for any solder
bridges or other problems. In particular, check for light shining
through the holes of unsoldered joints.

Battery connector
7-segment displays and decimal LEDs
installed When all the components are on the board, solder the battery snap
connector to the battery pads on the PC board - red to “+” and black
to “-”.
Initial checks

Set both VR1 and VR2 to their mid-range positions and connect a 9V supply to the battery connection. Press the
pushbutton. You should see something on the 7-segment LED displays, hopefully “-” on the left hand one.

Press the pushbutton again and the meter should turn off.

Turn it back on and short the leads together. The meter should read something less than 0.5 ohm. With the leads
shorted press the pushbutton again to zero the test leads. The reading should be “.00” with the left decimal lit. The
reading may bounce around +.02 ohms or so due to variation in the lead contact resistance.

Calibration

It is best to calibrate the unit before assembling it into the box. That way you can correct any assembly errors that
show up during calibration without having to disassemble the board from the box.

With the meter on and the leads zeroed as described above connect the supplied 82Ω 1% calibration resistor to the
probes and carefully adjust VR2 until the meter reads “82.” Then check that that it reads the supplied 5.6Ω
calibration resistor reasonably accurately (5.2 to 6.0) with the middle decimal lit.

Battery warning setup

Skip this bit if you disabled the automatic switch-off function by leaving one lead of R25 disconnected (see the
“Optional Modifications” section).

This adjustment is easiest if you have access to a variable DC power supply. If not, you will need to build the little
circuit shown here.

The adjustment procedure is as follows:

(1) With the ESR meter off and nothing

attached to the test leads turn VR1 (10K
ohm) fully clockwise (as viewed from the
component side of the PC board).

(2) Adjust the supply voltage to 5.5 volts,

then switch the meter on.

(3) Slowly turn VR1 counter clockwise

until the “b” battery warning indication
begins flashing on the right hand display.

(4) Turn the meter off, wind the power

supply back up to 9 volts, then switch the meter back on and check that the battery warning triggers when you drop
the supply back to 5.5 volts.
 Final Assembly

The pc board sits snugly in the bottom enclosure. Fasten the board
into place using the six self-tapping screws. The screw under the tie-
wrapped test leads may be difficult to get into place. You can omit it.

Remove the battery

compartment door
from the bottom of
the enclosure and
run the battery leads
through the opening
and as shown in the
picture.

Final Assembly

Battery Lead Dress

You are done!

That’s it! Install the enclosure top and secure it with the four self tapping screws. Push the battery into its
compartment and install the battery compartment door. Then put the labels on the front and start finding bad caps!

Before using your new meter we recommend that you read the section on ESR meter operation – it not only
contains useful hints but also lists precautions that you should follow.

What is bad ESR?

There is a chart of 3 X normal average ESR for various capacitor values and voltage ratings on the meter front
panel. There is no one bad value; it depends upon the rating of the capacitor you are testing.

In general, a capacitor with bad ESR will read at least 2 – 3 times the values given for a new capacitor by the
manufacturer. The values shown on the chart are generally 3 times the manufacturer’s specs. A really bad one
might be 10 times the values shown or more.

With experience you will be able recognize bad ones without consulting the chart.

Basic operation

The ESR Meter is extremely simple to operate but there are a few precautions to follow. Here is its basic step-by-
step operation:
(1). Insert the probe terminator of your choice into the shrouded plugs. A croc clip works well for out of circuit
capacitors, a probe for in-circuit.
(2). Press the button so the “-” symbol appears on the display.
(3). Hold the test probes tightly together – the test lead resistance is displayed.
(4). With the probes still together, press the button again to give a zeroed reading of “.00”. You can repeat this at
any time.
(5). Measure the capacitor’s ESR (it should be discharged first). A reading of “-” indicates a reading greater than
99Ω. Compare the reading to the graph on the front label. Good capacitors will have ESR below the graph lines,
bad above.
(6). When you’ve finished measuring, press the button with the probes separated. The meter switches off when
you release the button.
(7). When the battery is getting low, “b” flashes once per second and the display dims to conserve the remaining
battery capacity.

Precautions

(1). Beware charged capacitors:

The very first thing to do is to make certain that the equipment you’ll be using the ESR Meter on is disconnected
from all power. Most electrolytic capacitors will be discharged by the circuitry around them within a few seconds of
the power being switched off. However, be warned that filter capacitors in power supplies can remain
dangerously charged, especially if there’s a fault. Before using the meter, make sure that all power supply capacitors
are fully discharged. You can do this using well-insulated probes that include a series 100Ω 5W or similar power
resistor. Do not just short the capacitor’s terminals together as that can not only damage the capacitor but can also
be dangerous. Always allow several seconds to ensure a complete discharge. Apart from the risk of surprise and
injury to you, large charged capacitors can seriously damage the meter.

(2). Watch out for interference:

The meter can produce unsteady indications if its test leads pick up strong horizontal deflection signal voltages. To
avoid this, be sure to keep it away from operating (CRT) TVs and monitors when making measurements.

(3). Use straight test leads:

Do not add self-retracting “curly” test leads with your meter. Their inductance can cause measurement errors.

What else can it do?

Since publication of the Mk.1 design in 1996, I have received a lot of feedback from imaginative ESR Meter users
regarding other uses for it. The full list is on at
http://members.ozemail.com.au/ ~bobpar/esrhints.htm but here are some of the best ones:

(1). Resistance Measurement: as stated previously, this meter is really an AC ohmmeter with an equivalent test
frequency of about 100kHz and capable of measuring non-inductive resistances from 0.01Ω to 99Ω. As such, it can
be useful for locating short circuits on PC boards by showing the resistance of a copper track decreasing or
increasing as you approach or move away from the short. For example, this is useful when trying to identify which
one in a paralleled set of power transistors is shorted (thanks Mike Diack) or the check out power leads and
connectors (resistance is too low for a multimeter).
You can also make your own very low-value resistors by measuring out a length of nichrome or similar resistance
wire to give the required resistance. In addition, the ESR Meter can be used to check the contact resistance of
switches, connectors and relays. Just remember that any significant amount of inductance will cause measurement
errors. You cannot measure the DC resistance of a choke, transformer winding, video head or a roll of electrical
cable, for example.

(2). Basic Signal Generator: the meter’s test signal is a 500mV P-P (open circuit) burst of 8 usec pulses at a 2kHz
rate, repeated several times per second. As a result, it can be used as a signal source for basic checks on amplifiers,
loudspeakers and other audio components (thanks Joe Lussy). Richard Newstead (our UK distributor) reports that
the meter can be used as a simple wideband signal generator with useful signals out to 30 Mhz.

(3.)

Maintenance
The meter’s readings might become unsteady after a lot of use, due to oxidation or loosening of the test lead s.
Heavily spray the test lead plugs with contact cleaner of the kind which evaporates completely (eg, CRC “CO”
Contact Cleaner), then repeatedly insert and withdraw them from their s before it dries. If the test lead s have
become loose, gently re-tighten them with long needle-nose pliers.
If the test probes have developed a resistive layer of oxidation, give them a wipe with a tissue soaked in tuner
cleaner like CRC 2.26 or similar (thanks Joe Sopko).

It does not work, now what?

The ESR Meter’s firmware allows the microcontroller to do some basic testing of the electronics to help you
narrow down a problem to one area of the board. Before doing the self-test, it’s very important to first set VR1
to the center of its adjustment range, short out R30, 100R and make sure that the meter’s supply voltage is
in the range of 6.2 – 6.8V. Do not use a 9V battery for this test because it will cause a false F2 warning!

Switch the meter on by pressing and continuing to hold the button down, regardless of what the displays are
showing. After five seconds, they will go blank for a moment and then show a test result for two seconds. The
meter will then switch off by itself after you release the button.

If everything is more or less OK, you’ll see “.8.8” on the displays (this shows that all the display segments and
decimal point LEDs are working). However, if the microcontroller has detected a problem it will flash a fault code
consisting of an “F” on the left hand display and a character from 0-9 or an “A” on the right hand one.

Experience has shown that by far the most common cause of ESR meter kits not working properly is defective
soldering. When a fault code directs you to a particular part of the circuit, carefully check (using a bright light and
magnifier) for solder whiskers, non-soldered joints and track damage such as lifted solder pads.

If you cannot see anything abnormal, start checking for incorrect components and component placement errors
such as transistors of the wrong type or with their leads in the wrong holes. If that does not show up anything, you
might have received a defective component in the kit, though this is very rare. OK, here is a list of what the fault
codes indicate:

F0: Q11 is not discharging C10. Check around Q11 (2N3904), R21 (10kΩ), R22 (470kΩ) and pin 4 of IC2
(Z86E0412).

F1: C10 is charging too quickly. Check that R22 really is 470kΩ and that R19 & R20 are 10kΩ. Make sure C10 is
470nF (0.47µF, code “474”). Check also for soldering and component placement problems around transistors Q9 &
Q10 (2N3906).

F2: C10 is charging too slowly (or not at all). Check around Q9, Q10 (2N3906), R22 (470kΩ), R19 & R20 (10kΩ)
and C10 (470nF).

F3: Pulse amplifier output bias <440mV (i.e., at collector of Q8). Check R13 (100kΩ) & R14 (220kΩ) for correct
values and check that D6 isn’t reversed. Check around Q7 (2N3904), Q8 (2N3906) and around pin 8 of IC2 plus
associated components.
F4: Pulse amplifier output bias >1V. Carry out the same checks as for “F3” code. Check also that D5 isn’t
reversed.

F5: A test current source is permanently on. Check area around Q3, Q4 & Q5 (all 2N3906); R5, R7 & R9 (2.2kΩ);
and pins 15, 16 & 17 of IC2.

F6: No output from pulse amplifier. Check around C7 (33nF), R12 (1kΩ), D3 & D4 (1N4002), C5 (100nF) and C6
(47µF bipolar).

F7: Q3 not sourcing current. Check around Q3 (2N3906), R5* (2.2kΩ), R6 (10kΩ) and pin 15 of IC2.

F8: Q4 not sourcing current. Check around Q4 (2N3906), R7* (2.2kΩ), R8 (1kΩ) and pin 16 of IC2. F9: Q5 not
sourcing current. Check around Q5 (2N3906), R9* (2.2kΩ), R10 (100Ω), IC2 pin 17.

F9: Q5 not sourcing current. Check around Q5 (2N3906), R9* (2.2kΩ), R10 (100Ω), IC2 pin 17.

FA: Q6 not switching on. Check around Q6 (2N3904), R24 (10kΩ) and pin 1 of IC2. The microcontroller cannot
perform detailed tests on every component, so it’s possible that your meter is malfunctioning even though the self-
testing hasn’t shown up a problem. For example, if the meter is behaving strangely, “freezing” up or giving absurd
readings on some values of test resistors, the most likely cause is a mix-up in the values of R6 (10kΩ), R8 (1kΩ) and
R10 (100Ω). On the other hand, if the meter produces readings but there’s something wrong with the displayed
characters, this is almost certainly due to one or more solder bridges between the pins of the displays or around IC3.

If the meter does not stay switched on when you push the button, check around Q2 (2N3904), R3 (15kΩ), R29
(2.7kΩ) and pin 2 of IC2. If it switches off when you short the test leads, R2 (4.7kΩ) may be the incorrect value or
Q1 (2N3906) may have a low current gain. Finally, if you can’t get the meter into the test mode, zero it or switch it
off, check for solder “whiskers” and open circuits around pin 3 of IC2, R4 (47kΩ) and D2.
If none of the above has helped you to identify the problem, there is a page of fault-finding information on my
website: http://members.ozemail.com.au/ ~bobpar/esrprob.htm. Do a Google search for “ESR meter
faultfinding” if you can’t find it.

Disabling automatic switch-off

If you’d like to power the meter from an external 9V DC supply and have it operating continuously, just disconnect
one end of R25 (47kΩ). This disables the automatic switch-off function but note that the low battery warning will
no longer work if you do this.

Of course, you can easily reconnect R25 if you change your mind in the future.

For more modifications, including a buzzer to help you discriminate between good and bad electrolytics without
having to look at the meter, go to my ESR Meter Hints web page at http://members.ozemail.com.
au/~bobpar/esrhints.htm. If all else fails send a question to [email protected].