Scribd
Upload
258 views4 pages

Hyundai Door Lock Actuator Repair Guide

The document provides instructions for inspecting and testing the power door lock actuators, switches, and trunk lid actuator on a 2007 Hyundai Elantra. The procedures include removing door trim panels and modules to access the actuators and switches, disconnecting connectors, and checking actuator operation and switch continuity using a table of terminal connections for each component.

Uploaded by

Vinnie Ingalls
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
258 views4 pages

Hyundai Door Lock Actuator Repair Guide

The document provides instructions for inspecting and testing the power door lock actuators, switches, and trunk lid actuator on a 2007 Hyundai Elantra. The procedures include removing door trim panels and modules to access the actuators and switches, disconnecting connectors, and checking actuator operation and switch continuity using a table of terminal connections for each component.

Uploaded by

Vinnie Ingalls
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

https://www.hyundaitechinfo.com/viewer/content.asp?IsPrint=true&imgn...

ELANTRA(HD) >2007 > G 2.0 DOHC > Body Electrical System > Power Door Locks > Power Door Lock Actuators > Repair procedures

INSPECTION FRONT DOOR LOCK ACTUATOR


1. Remove the front door trim. (Refer to the Body group - Front door) 2. Remove the front door module. (Refer to the Body group - Front door). 3. Disconnect the connectors from the actuator.

4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

REAR DOOR LOCK ACTUATOR


1. Remove the rear door trim panel. (Refer to the Body group - Rear door) 2. Remove the rear door module. (Refer to the Body group - Rear door) 3. Disconnect the connectors from the actuator.

1 of 4

6/18/2012 7:36 PM

https://www.hyundaitechinfo.com/viewer/content.asp?IsPrint=true&imgn...

4. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

TRUNK LID ACTUATOR


1. Remove the trunk trim. (Refer to the Body group - Tailgate) 2. Disconnect the 3P connector from the actuator.

3. Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.

FRONT DOOR LOCK SWITCH


1. Remove the front door trim. (Refer to the Body group - Front door) 2. Remove the front door module. (Refer to the Body group - Front door).

2 of 4

6/18/2012 7:36 PM

https://www.hyundaitechinfo.com/viewer/content.asp?IsPrint=true&imgn...

3. Disconnect the connectors from the actuator.

4. Check for continuity between the terminals in each switch position when inserting the key into the door according to the table.

REAR DOOR LOCK SWITCH


1. Remove the rear door trim panel. (Refer to the Body group - Rear door) 2. Remove the rear door module. (Refer to the Body group - Rear door) 3. Disconnect the connectors from the actuator.

3 of 4

6/18/2012 7:36 PM

https://www.hyundaitechinfo.com/viewer/content.asp?IsPrint=true&imgn...

4. Check for continuity between the terminals in each switch position according to the table.

TRUNK LID OPEN SWITCH


1. Remove the trunk trim. (Refer to the Body group - Tailgate) 2. Disconnect the 3P connector from the actuator.

3. Check for continuity between the terminals in each switch position according to the table.

4 of 4

6/18/2012 7:36 PM

You might also like