Absolutely leak proof gasketing

Characteristics and Advantages

Page 1

Hollow Lip Weld-Ring Gaskets

Page 2

Weld-Ring Gaskets
Page 3

Membrane Weld-Ring Gaskets

Page 4

Common Materials
Page 4

Dimensions

Weld-Ring Gaskets

Weld-Ring Gaskets

Profile A21, page 5

Profile A24, page 5
Profiles A22 and A23, pages 6-7
Profiles A22N and A23N, pages 8-11

Typical characteristics
Profiles

Inside welding seams

prevents crevice
corrosion between
weld ring and flange.

Outside weld seams

allow repair welding
without dismantling.

Compensation of
radial differential
expansion.

Dismantling and rewelding

Standard
procedure

Not possible

Up to max. r ~5 mm
depends on hollow lip
wall thickness

Easy to dismantle
with a 2mm cut off
disc.
Can be re-welded up
to 4 times

Can be applied as an
additional intermittent
weld for further
fastening

Standard procedure

Up to max. r ~5 mm
depends on hollow lip
wall thickness

Easy to dismantle
with a 2mm cut off
disc.
Can be re-welded up
to 4 times

a) An additional
intermittent weld for
further fastening
b) If susceptible to
corrosion

a) Standard procedure
b) Additional fastening
through intermittent
weldments

Effect is small
because of the small
hollow lip
dimensions.
max. r ~ 0,5 mm

a) An additional
intermittent weld for
further fastening
b) If susceptible to
corrosion

a) Standard procedure
b) Additional fastening
Befestigungshilfe.
through intermittent
weldments

hardly possible
max.. r ~ 0,1 mm

Only possible method

Not possible.
Additionally flange
form M to DIN 2526
required

Effect is small and

depends on projection
of gaskets
max.. r ~ 0,3 mm

Difficult to dismantle.

Can be re-welded up
to 3 times
Use cut-off disc.
Material loss 2-3 mm
each.
Can be rewelded
up to 5 times
Use cut-off disc.
Material loss 2-3 mm
each.
Can be rewelded
up to 5 times

It is recommended to use weld-ring gaskets for any application where it is absolutely necessary to have a leak proof
joint, and also a limited opportunity for disassembling is
required. Underlying reasons for this requirement may be
containment of hazardous materials or the need for a
shutdown free operation.
The limited opportunity for disassembling mean in this
case, that the bolts have to be removed and the weld seam
has to be cut besides. The gasket can be reused and
rewelded up to five times depending on gasket type.
Gasket materials are generally the same or similar to the
pipe or flange material. Weld-ring gaskets can only be
used in pairs.
Depending on requirements a gasket profile is to select
from previously shown table. In the overview, the selection
criteria are shown versus typical characteristics for profiles
A21 to A25.
The welded connection between one half of the weld-ring
gasket and one flange is defined as welded joint in the
following text. The welded joint can either be an inside or
outside weld, or even be a combination of both. The
welding connection of the two gasket halves to each other
is defined as seal-weld.

Hollow Lip Weld-Ring Gaskets

Weld-ring gaskets with hollow lips according to profile

A24, A25 and A23 offer improved stress conditions in the
seal weld. The use of weld-ring gaskets with hollow lips is
recommended for connecting constructional parts with
different thermal expansion coefficients.
Profiles A24 and A25 have the advantage of increased
ability to absorb movement. As an example, they are
preferably installed to seal heat exchanger bonnet flanges
and tube plates, where different radial movement occurs.
With profile A24, the welded joint are not accessible from
the outside. However, for many applications this is an
advantage, especially where crevice corrosion is assumed.
In such instances profiles A24H, A24K, A24KVR and
A24N are recommended.

Weld-Ring Gaskets

Characteristics

Safety instruction:
Weld-ring gaskets with hollow lip profiles A24 and A25
sometimes have the tendency to build up condensation,
which can expand due to sudden temperature rises. In
order to prevent this, the design of each gasket-half has 4
radial grooves, 1.5mm deep and 3mm wide.

All weld-ring gaskets can be fitted with other additional

auxillary gaskets. This may be advantageous for several
reasons:
a) Hydraulic pressure testing can be performed using
auxiliary gasketing before final welding.
b) Testing or start up can be accomplished utilizing an
auxiliary gasket, which allows repeated dismantling.

Profile

Cross-Section

A23

c) The additional gasket may be the primary operational

gasket. The weld-rings would only be welded in the
event of gasket failure.
For weld-ring gaskets without the additional gasket, bolt
forces must be increased to ensure that the weld-ring
gasket halves contact each other without any gap. Calculation of the bolt forces for weld-ring gaskets with an
auxiliary gasket require a computation for weld-ring gasket
using the outside diameter plus a calculation for the
auxiliary gasket. In this case a gap of 0.3 mm exists. All
weld-ring gaskets should have a surface roughness of
RZ~ 25 to 50 m.

A24

A24H

A24K

A25

Profile A24H, one gasket-half is designed with a convex

sealing surface. The radius is designed considering pressure, temperature and required construction materials.
Frequently a galvamic coating of the sealing face can be
very usefull.
Profile A24K, one gasket-half is designed with a grooved
sealing surface, which is equipped with a layer of PTFE,
graphite or AFS* with 0.5 mm thickness. Layer material
depends upon requirements.
* AFS = asbestosfree fibre sheet

Weld-Ring Gaskets

Profile A22 Weld-ring gaskets have the same thickness as

profiles A23 and A24 (2x15=30mm). Therefore there is
enough space for the necessary joint welding. No special
flanges are required.

A24KVR

Profile A24KVR with male and female designs. The female part is designed as a grooved gasket.

Weld-Ring Gaskets

Hollow Lip Weld-Ring Gaskets

Layers for this gasket are PTFE, graphite, silver or, AFS*
depending on design requirements. Thickness of layer
0.5 mm.
Profile A24N is designed with a groove to accommodate
a profile SpV3N spiral wound gasket. Materials of construction available are listed in brochure "Spiral Wound
Gaskets SPIROFLEX".
Spiral wound gasket SpV3N in the main load

Using this type, it is easy to make additional welds to stop

leaking, because all welding seams are on the outside.
Necessary bolts are longer and thus there is more positive
elastic behavior.
Profiles A22 to A22N are preferably used on pipeline
applications. In such cases there is no expansion differential between gaskets and flanges due to identical flanges
and construction material.
Another advantage is that the greater thickness permits
the use of an auxiliary gasket (see previous page weld-ring
gaskets profile A24).

A24N

Profile

For spiral wound gaskets with a thickness of 4.5 mm the

groove depth is 3,0-0,1mm. Spiral wound gaskets with a 5.5
mm thickness have a groove depth of 3,2-0,1mm.

A22

Weld-ring gaskets may also be supplied with male/female

design as per profile A24R to accommodate a grooved
gasket. If damaged the complete grooved gasket can be
replaced.

A22H

Cross-Section

A22K

A22KVR

A24R + B27A

A22N

For profiles A25 and A23 the same auxiliary gasket

variety is available as for profile A24.
Profile A23 is illustrated with a "protector" gasket, which is
not leak proof.

* AFS = asbestosfree fibre sheet

Membrane rings per DIN 2695 are 4mm thick. Due to

limited ability to take up radial differential expansion,
membrane weld gaskets should be of the same material as
the flange. For installation, each membrane half must be
welded to the flange half by an inside joint welding. After
flange assembly the outside seal-weld is made. Errors
made on the inside joint welding are difficult to repair.
Profile

Cross-Section

A21

A Study must be made to determine if there is enough room

to carry out the seal-weld procedure. If not, special flanges
according to DIN 2526 type M design are required.

Common Gasket Materials

Material abbreviation
EN 10 027-1

Material-No.
EN 10 027-2

Temperature
of Medium

S235JRG2

1.0038

bis 4250C

16Mo3

1.5415

425 bis 4750C

13CrMo4-5

1.7335

475 bis 5200C

10CrMo9-10

1.7380

520 bis 5800C

X6CrNiTi18-10

1.4541

350 bis 5500C

X6CrNiMoTi17-12-2

1.4571

max. 5500C

* further technical data see our leaflet Common Materials

Weld-Ring Gaskets

Membrane Type Weld-Ring Gaskets

The following figure depicts gasket profile A21K installed

between type M flanges.

Profile A21K membrane weld gaskets are designed with

concentric grooves. As required by the process, soft layers
of PTFE, graphite, silver or AFS* with about 0.5 mm
thickness have to be specified.

* asbestosfree fibre sheet

Profile A21

Profile A24

DIN 2695 for DIN-flanges

Works standard 126 for DIN-flanges

Profile A21

Profile A24

Weld-Ring Gaskets

Dimension Table

Dimension Table

Membrane weld-ring gaskets profile A21

DIN 2695 for PN designated flanges

Works standard 126

Dimensions in mm

Weld-ring gaskets profile A24 for DIN-flanges

DN

d23) for PN

d1
63

100

160

250 u. 320

400

d32)

Example to order a weld-ring gasket profile A24, nominal

diameter 500, nominal pressure 40, works standard 126,
of...1).

80

90

143

149

149

153

153

123

100

115

169

176

176

179

179

149

125

142

206

213

213

216

216

186

150

165

243

248

248

248

248

218

The weld-ring gasket consists of two weld-ring halves

200

214

305

315

315

315

315

285

Dimensions in mm

250

264

360

370

370

370

340

300

310

420

430

430

400

460

400

386

539

519

DIN 2695 for Class designated flanges

Dimensions in mm

NPS

d23) for Class

d1
150

d32)

300 600 900 1500 2500 150 300 600

92 130 142 142 157 157 157 116 122

122

4 118 167 172 180 187 187 187 146 150

157

5 144 190 208 216 216 216 216 172 180

186

6 170 215 243 246 246 246 246 196 216

216

8 220 272 300 300 300 300 300 252 270

270

10 273 332 354 354 354 354 354 308 324

324

12 322 400 411 411 411 411 411 370 381

381

14 360 440 443 443 443 443

- 413 413

413

16 412 500 500 500 500 500

- 470 470

470

Example to order a membrane weld-ring gasket, profile

A21, inner diameter (ID=d1) = 115 mm, outer diameter
(OD=d2) = 169 mm, of ...1).
Membrane weld-ring gasket A21, 115 x 169 mm,
DIN 2695, 1.5415 (A204 Gr. A;4027)
The membrane weld-ring gasket is comprised of 2 weld-rings.

25
d2

d1

40
d2

d1

63
d2

d1

100
d2

d1

d2

250

- 258 389

300

- 306 456

350

- 348 472 341 484 334 510

400

- 395 544 388 541

500

- 498 622 490 626

655

702

600

- 598 729

745

762

811

700

- 696 831

850

877

948

800

- 795 940

900

- 892 1040

1000 1006 1126 991 1152

1200 1205 1340
1400 1402 1540
1600 1598 1762
1800 1795 1962
2000 1990 2166

1362

972
1082
1192
1396

986
1106
1218
1450

570

to be specified
by purchaser**

490

16
d1

to be specified
by purchaser**

482

DN

to be specified
by purchaser**

340

PN

to be specified
by purchaser**

350

Weld-ring gasket A24, DN 500, PN 40, 490 x 626, WN

126, 1.5415 (A182 Gr. F1; F2), s = ...*

1576

1616

1796

1828

1998

2228

* Dimension "s" to customer specification. Wall thickness have to be

specified based upon pressure, temperature, material of construction and
radial movement.
** Weld-ring gaskets per profiles A24 to A24N are not available for smaller
width than 60 mm [(d2-d1)/2=60 mm].
1) Please specify required material in any inquiry and order.

1)

Please specify required materials in any inquiry and order .

2)
When sloping off the flanges the seating ledges must be fitted to these
dimensions.
3)
A projektion of 15 mm is preferable; but 10 mm are necessary. (Maximum
outer diameter: centering diameter less 4 mm).

Profile A22 and A23

Works standard 110 for DIN-flanges

Profile A22 and A23

Works standard 110

Weld-ring gaskets profile A22 and A23 for DIN-flanges
Example to order a weld-ring gasket profile A22, nominal
width 100, nominal pressure 160, works standard 110,
of...1).
Weld-ring gasket A22, DN 100, PN 160, works standard
110, 1.5415 (A204 Gr. A; 4027)
The weld-ring gasket consists of two weld-ring halves.
For correct welding procedures, please check:
a) Sealing ledge details.
b) If a flat flange is used
c) Or,if in respect to Kempchen standard WN 110, the outer diameter d3
should be smaller than given.

Weld-Ring Gaskets

Dimension Table

1) Please specify required material in any inquiry and order.

2) For DN 10 and 15 sizes,only 4 mm.

Dimensions in mm

PN 10 40
DN
10
15
20
25
32
40
50
65
80
100
125
150
(175)
200
250

d2

d3

27
32
38
46
55
60
75
90
105
125
150
178
210
235
285

41
46
58
66
75
80
95
110
125
145
170
198
230
255
305

d1
13,6
17,3
22,3
28,5
37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8

PN 63
d1
13,6
17,3
28,5
37,2
42,5
54,5
69,7
81,7
106,3
130,7
157,1
181,1
204,9
255,4

PN 100

d2

d3

30
35
50
55
60
75
90
105
125
150
178
210
235
285

50
55
70
75
80
95
110
125
145
170
198
230
255
305

d1

PN 160

d2

d3

13,6
17,3
28,5
37,2
42,5
53,9
68,9
80,9
104,3
127,1
154,1
176,1
199,1
248

30
35
50
55
60
75
90
105
125
150
178
210
235
285

50
55
70
75
80
95
110
125
145
170
198
230
255
305

d3

d1

d1
13,6
17,3
27,9
41,1
52,3
66,1
76,3
98,3
119,7
143,3
165,3
187,1
233

PN 250

d2

d3

30
35
50
60
75
90
105
125
160
185
205
230
280

50
55
70
80
95
110
125
145
180
205
225
250
300

d1
12
16,1
26,5
38,3
47,7
60,1
79,6
98,6
120,4
142,8
174,7
194,5
234,5

PN 320

d2

d3

30
35
50
60
80
100
115
135
160
185
230
255
310

50
55
70
80
100
120
135
155
180
205
250
275
330

d1
12
14,9
23,7
35,7
47,5
66,9
76,6
101
128,3
143,7
163,1
184,5
243,9

PN 400

d2
30
35
50
60
90
110
125
145
172
205
230
255
335

d3

d1

d2

d3

50 10
30 50
55 16,9 40 60
70 28,2 50 70
80 40,3 80 100
110 51,1 90 110
130 69,6 120 140
145 79,3 130 150
165 95,3 150 170
192 133,7 188 208
225 149,1 218 238
250
275 193 285 305
355
-

Dimensions in mm
DN

d1

PN 10
d2

d3

d1

PN 16
d2

d3

d1

PN 25
d2

300
350
400
(450)
500
600
700
800
900
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000

309,7
314,4
392,2
443
493,8
595,4
695,2
797
894
996
1198
1396
1592
1790
1984
2184
2380
2576
2776
2972

335
385
435
490
540
645
750
840
945
1045
1260
1455
1665
1860
2070
2270
2470
2675
2875
3080

355
405
455
510
560
665
770
860
965
1065
1280
1475
1685
1880
2090
2290
2490
2695
2895
3100

309,7
339,6
390,4
441,2
492
592
693,6
793
894
996
1195
1392
1588
1785
1980
2175
-

335
385
435
490
540
645
750
850
945
1045
1260
1460
1665
1865
2070
2275
-

355
405
455
510
560
665
770
870
965
1065
1280
1480
1685
1885
2090
2295
-

307,9
339,6
388,6
439,6
488
587,6
686,2
784,6
882
988
1188
1385
1585
1780
1975
-

335
385
435
490
540
645
750
855
960
1055
1265
1465
1665
1870
2075
-

355 307,9
405 338,0
455 384,4
510 435,2
560 479,6
665 585
770 683
875 781
980 880
1075 981
1285 1176
1485 1375
1685 1570
1890
2095
-

PN 40
d2
335
385
435
490
540
645
750
855
960
1060
1275
1475
1680
-

d3

d1

PN 63
d2

d3

355 301,9 335 355

405 330,6 385 405
455 378
435 455
510
560 476
560 580
665 575
655 675
770 671
760 780
875 769
870 890
980 864
975 995
1080 964 1085 1105
1295 1156 1295 1315
1495
1700
-

d1

PN 100
d2

295,5
323,6
371,4
464
560
651
-

335
385
435
560
670
780
-

d3
355
405
455
580
690
800
-

d1

PN 160
d2

279,5
-

335
-

d3

d1

PN 250
d2

355
-

244
-

335
-

d3
355
-

Profile A22 and A23

Works standard 111 for ASME/ANSI-flanges
Works standard 143 for ASME B16.47 series A flanges

Dimensions in mm

Kempchen works standard 111

Weld-ring gaskets profiles A22 and A23 for ASME/
ANSI-flange .

150300

400900
d1

NPS

Example to order a weld-ring gasket profile A22, nominal

width 3", nominal pressure 900, works standard 111 of...1).

Weld-ring gasket A22, NPS 3", Class 900, WN 111,

1.5415 (A204 Gr. A; 4027).

1
1
1
2
2
3
3
4
5
6
8
10
12
14
16
18
20
22
24

The weld-ring gasket consists of two weld-ring halves.

15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5

14,0
18,8
24,4
32,5
38,1
49,3
58,9
73,7
85,3
97,3
122,2
146,3
193,8
247,6
298,4
330,2
381,0
431,8
482,6
533,4
584,2

Class
15002500

6,4
11,0
15,2
22,8
27,9
38,2
45,0
58,4
80,1
103,2
124,4
174,6
222,3
273,1
304,8
355,6
406,4
457,2
508,0
558,8

150

3002500

d2

d3

d2

d3

29
33
42
52
60
75
96
105
131
148
160
185
240
295
372
404
461
525
575
632
683

45
53
62
72
80
95
116
125
151
168
180
205
260
315
392
424
481
545
595
652
703

29
33
42
55
64
83
96
118
131
148
177
207
261
315
372
404
461
525
575
632
683

45
53
62
75
84
103
116
138
151
168
197
227
281
335
392
424
481
545
595
652
703

Weld-Ring Gaskets

Dimension Table

1) Please specify required material in any inquiry and order.

2) At NPS " and NPS " only 4 mm

Works standard 143

Weld-ring gasket profiles A22 and A23 for ASME B16.47
series A flanges.

For correct welding procedures, please check:

a) Sealing ledge details.
b) If a flat flange is used
c) Or,if in respect to work standard WN 110, the outer diameter d3
should be smaller than given.

Example to order a weld-ring gasket, profile A22, nominal

width 30", nominal pressure 150, works standard 143,
of...1).
Weld-ring gasket A 22, NPS 30", class 150, WN 143,
1.5415 (A204 Gr. A; 4027).
The weld-ring gasket consists
of two weld-ring halves.

Dimensions in mm
NPS
Zoll

All dimensions are general recommendations subject to user approval.

26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60

Class 150 - 300

d1

641,4
692,2
743,0
793,8
844,6
895,4
946,2
997,0
1047,8
1098,6
1149,4
1200,2
1251,0
1301,8
1352,6
1403,4
1454,2
1505,0

d2

695,8
746,6
797,4
848,2
899,0
949,8
1000,6
1051,4
1102,4
1153,0
1203,8
1254,6
1305,4
1356,2
1407,0
1457,8
1508,6
1559,4

Class 400 - 600

d3

d1

715,8
766,6
817,4
868,2
919,0
969,8
1020,6
1071,4
1122,2
1173,0
1223,8
1274,6
1325,4
1376,2
1427,0
1477,8
1528,6
1579,4

635,0
685,8
736,6
787,4
838,2
889,0
939,8
990,6
1041,4
1092,2
1143,0
1193,8
1244,6
1295,4
1346,2
1397,0
1447,8
1498,6

d2

695,8
746,6
797,4
848,2
899,0
949,8
1000,6
1051,4
1102,4
1153,0
1203,8
1254,6
1305,4
1356,2
1407,0
1457,8
1508,6
1559,4

Class 900
d3

715,8
766,6
817,4
868,2
919,0
969,8
1020,6
1071,4
1122,2
1173,0
1223,8
1274,6
1325,4
1376,2
1427,0
1477,8
1528,6
1579,4

d1

d2

d3

622,4
673,2
724,0
774,8
825,6
876,4
927,2
978,0
1028,8
1079,6
1130,4
1181,2
-

708,4
759,2
810,0
860,8
911,6
962,4
1013,0
1064,0
1114,8
1165,6
1216,4
1267,2
-

728,4
779,2
830,0
880,8
931,6
982,4
1033,0
1084,0
1134,8
1185,6
1236,4
1287,2
-

Profiles A22N and A23N

Works standard 134 for DIN flanges

Profiles A22N and A23N

DimensionTable WN 134, PN 10
Dimensions in mm

DN

Works Standard 134

Weld-ring gasket profiles A22N and A23N for DINflange.
Example to order a weld-ring gasket, profile A22N, nominal
width 100, nominal pressure 160, with a spiral wound
gasket profile SpV3N, works standard 134, of...1).
Weld-ring gasket A22N, DN 100, PN 160, works standard 134, 1.5415 (A204 Gr. A; 4027) / SpV3N, 1.4541/
graphite.

32 *
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
(450)
500
600
700
800
900
1000

d1

37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,9
207,3
260,4
309,7
341,4
392,2
443,0
493,8
595,4
695,2
797,0
894,0
996,0

d2

d3

d4

groove
d5

65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
223 237 189,0 209
246 260 212,0 232
299 315 264,0 285
354 370 314,6 338
390 410 348,6 372
445 465 401,2 427
500 520 453,0 481
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
17,4
18,5
18,5
18,5

6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 214 231
9,0 266 284
10,0 317 337
10,0 351 371
11,0 404 426
12,0 456 480
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048

Weld-Ring Gaskets

Dimension Table

DimensionTable WN 134, PN 16
Dimensions in mm

DN

* Depth of turned groove t = 4 mm

For correct welding procedure, please check:
a) Sealing ledge details
b) If a flat flange is used
c) Or, if in respect to work standard WN 134, outer diameter d3
should be smaller than given.

1) Please specify required material in any inquiry and order.

32 *
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500
600
700
800
900
1000

d1

37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,9
207,3
260,4
309,7
339,6
390,4
492,0
592,4
693,4
793,0
894,0
996,0

d2

d3

d4

groove
d5

65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
223 237 189,0 209
246 260 212,0 232
299 315 264,0 285
354 370 314,6 338
390 410 348,6 372
445 465 401,2 427
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0
15,0
17,4
18,5
18,5
18,5

6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 214 231
9,0 266 284
10,0 317 337
10,0 351 371
11,0 404 426
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048

Profiles A22N and A23N

Works standard 134 for DIN-flanges

Dimension Table WN 134, PN 25

Dimension Table WN 134, PN 40

Dimensions in mm

Dimensions in mm

DN

32
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500
600
700
800
900
1000

d1

37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8
307,9
339,6
388,8
488,0
588,0
686,0
784,6
882,0
981,0

d2

d3

d4

groove
d5

65
79
40,0
54
71
85
46,0
60
84
98
59,0
73
101 115
74,6
90
115 135
86,6 102
141 155 111,4 128
166 180 136,4 153
196 210 165,2 183
225 245 189,0 209
250 270 214,0 234
310 330 269,0 290
360 380 317,6 341
390 410 348,6 372
445 465 399,2 425
555 575 506,0 534
660 680 608,0 638
770 790 710,2 745
875 895 813,0 850
970 990 908,0 945
1075 1095 1012,0 1049

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,3
10,0
10,0
10,5
11,7
11,7
12,9
14,0
15,0
17,4
18,5
18,5
18,5

6,0
41
53
6,0
47
59
6,0
60
72
6,5
76
89
6,5
88 101
7,0 113 127
7,0 138 152
7,5 167 182
8,5 191 208
8,5 216 233
9,0 271 289
10,0 320 340
10,0 351 371
11,0 402 424
12,0 509 533
13,0 611 637
15,0 714 744
16,0 817 849
16,0 912 944
16,0 1016 1048

DN

32
40 *
50 *
65 *
80
100 *
125 *
150 *
(175) *
200 *
250
300
350
400
500

d2

d1

37,2
43,1
54,5
70,3
82,5
107,1
131,7
159,3
182,5
206,5
258,8
307,9
338,0
388,4
479,6

65
71
84
101
115
141
166
196
225
250
310
360
390
440
540

d3

d4

79
85
98
115
135
155
180
210
245
270
330
380
410
460
560

40,0
46,0
59,0
74,6
86,6
111,4
136,4
165,2
189,0
214,0
269,0
317,6
347,6
394,2
491,0

groove
d5

54
60
73
90
102
128
153
183
209
234
290
341
371
420
519

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,7
7,7
8,3
8,3
8,9
10,0
10,0
10,5
11,7
11,7
12,9
14,0

6,0
6,0
6,0
6,5
6,5
7,0
7,0
7,5
8,5
8,5
9,0
10,0
10,0
11,0
12,0

Dimension Table WN 134, PN 100

Dimensions in mm

Dimensions in mm

DN

25 *
32 *
40 *
50
65
80
100
125
150
(175)
200
250
300
350
400

d1

28,5
37,2
42,5
54,5
69,7
81,7
106,3
130,7
157,1
181,1
204,9
255,4
301,9
330,6
378,0

d2

61
65
76
85
105
120
145
175
200
225
250
305
355
385
435

d3

d4

75
79
90
105
125
140
165
195
220
245
270
325
375
405
455

33,0
40,0
48,0
58,0
74,6
88,6
111,4
139,2
164,0
188,0
212,0
265,0
311,6
341,6
389,2

groove
d5

47
54
62
72
90
104
128
157
183
208
232
286
335
365
415

width

7,0 6,0
7,0 6,0
7,0 6,0
7,0 6,0
7,7 6,5
7,7 6,5
8,3 7,0
8,9 7,5
9,5 8,0
10,0 8,5
10,0 8,5
10,5 9,0
11,7 10,0
11,7 10,0
12,9 11,0

34
41
49
59
76
90
113
141
166
190
214
267
314
344
392

46
53
61
71
89
103
127
156
182
207
231
285
334
364
414

53
59
72
89
101
127
152
182
208
233
289
340
370
419
518

* Depth of turned groove t = 4 mm

For correct welding procedure, please check:
a) Sealing ledge details
b) If a flat flange is used
c) Or, if in respect to work standard WN 134, outer diameter d3
should be smaller than given.

Dimension Table WN 134, PN 63

spiral wound
gasket
width
d6
d7

41
47
60
76
88
113
138
167
191
216
271
320
350
397
494

Weld-Ring Gaskets

Dimension Table

DN

25 *
32 *
40 *
50
65
80
100
125
150
(175)
200
250
300
350

d1

28,5
37,2
42,5
53,9
68,9
80,9
104,3
127,1
154,1
176,1
199,1
248,0
295,5
323,6

d2

61
65
76
85
105
120
145
170
200
225
245
295
350
385

d3

d4

75
79
90
105
125
140
165
190
220
245
265
315
370
405

33,0
40,0
48,0
58,0
74,6
87,6
111,4
135,2
164,0
186,0
207,0
256,0
306,6
337,6

groove
d5

47
54
62
72
90
103
128
153
183
206
227
277
330
361

width

spiral wound
gasket
width
d6
d7

7,0 6,0
7,0 6,0
7,0 6,0
7,0 6,0
7,7 6,5
7,7 6,5
8,3 7,0
8,9 7,5
9,5 8,0
10,0 8,5
10,0 8,5
10,5 9,0
11,7 10,0
11,7 10,0

34
41
49
59
76
89
113
137
166
188
209
258
309
340

46
53
61
71
89
102
127
152
182
205
226
276
329
360

Profiles A22N and A23N

Works standard 134 for DIN-flanges

Dimension Table WN 134, PN 160

Dimension Table WN 134, PN 320

Dimensions in mm

Dimensions in mm

DN

25
40*
50
65
80
100
125
150
(175)
200
250
300

d1

27,9
41,1
52,3
66,1
76,3
98,3
119,7
143,3
165,3
187,1
233,0
279,5

d2

61
76
90
105
115
140
160
190
215
230
280
335

d3

d4

75
90
110
125
135
160
180
210
235
250
300
355

33,0
48,0
59,0
72,6
83,6
106,4
126,2
152,0
175,0
194,0
241,0
290,6

groove
d5

47
62
73
88
99
123
144
171
195
214
262
314

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,7
7,7
8,3
8,9
9,5
10,0
10,0
10,5
11,7

6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0
10,0

34
49
60
74
85
108
128
154
177
196
243
293

46
61
72
87
98
122
143
170
194
213
261
313

DN

10*
15*
25
40
50
65
80
100
125
150
(175)
200
250

d1

12,0
14,9
23,7
35,7
47,5
66,9
76,6
101,0
128,3
143,7
163,1
184,5
243,9

d2

46
51
60
75
90
110
125
145
172
205
230
255
335

d3

d4

60
65
80
95
110
130
145
165
192
225
250
275
355

18,0
23,0
30,0
43,0
56,0
75,6
88,6
109,4
136,2
160,0
182,0
205,0
274,0

groove
d5

width

32 7,0
37 7,0
44 7,0
57 7,0
70 7,0
91 7,7
104 7,7
126 8,3
154 8,9
179 9,5
202 10,0
225 10,0
295 10,5

spiral wound
gasket
width
d6
d7

6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0

Dimension Table WN 134, PN 250

Dimension Table WN 134, PN 400

Dimensions in mm

Dimensions in mm

DN

10*
15*
25*
40
50
65
80
100
125
150
(175)
200
250

d1

12,0
16,1
26,5
38,3
47,7
60,1
79,6
98,6
120,4
142,8
174,7
194,5
234,5

d2

46
51
61
75
85
100
120
140
165
190
230
255
310

d3

d4

60
65
75
95
105
120
140
160
185
210
250
275
330

18,0
23,0
33,0
45,0
54,0
67,6
87,6
106,4
129,2
152,0
198,0
220,0
257,0

groove
d5

width

32 7,0
37 7,0
47 7,0
59 7,0
68 7,0
83 7,7
103 7,7
123 8,3
147 8,9
171 9,5
218 10,0
240 10,0
278 10,5

spiral wound
gasket
width
d6
d7

6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5
8,5
9,0

19
24
34
46
55
69
89
108
131
154
200
222
259

31
36
46
58
67
82
102
122
146
170
217
239
277

DN

d1

d2

10* 10,0 46
15* 16,9 51
25
28,2 65
40
40,3 80
50
51,1 90
65
69,6 120
80
79,3 130
100
95,3 150
125 133,7 188
150 149,1 218
200 193,0 285

d3

d4

60
65
85
100
110
140
150
170
208
238
305

18,0
23,0
35,0
49,0
59,0
82,6
92,6
109,4
147,2
169,0
224,0

groove
d5

width

32 7,0
37 7,0
49 7,0
63 7,0
73 7,0
98 7,7
108 7,7
126 8,3
165 8,9
188 9,5
244 10,0

19
24
31
44
57
77
90
111
138
162
184
207
276

31
36
43
56
69
90
103
125
153
178
201
224
294

Weld-Ring Gaskets

Dimension Table

spiral wound
gasket
width
d6
d7

6,0
6,0
6,0
6,0
6,0
6,5
6,5
7,0
7,5
8,0
8,5

19
24
36
50
60
84
94
111
149
171
226

31
36
48
62
72
97
107
125
164
187
243

* Depth of turned groove t = 4 mm

For correct welding procedure, please check:
a) Sealing ledge details
b) If a flat flange is used
c) Or, if in respect to work standard WN 134, outer diameter d3
should be smaller than given.

10

Profiles A22N and A23N

Works standard 135 for ASME/ANSI flanges

Works standard 135

Weld-ring gasket profile A22N and profile A23N for
ASME/ANSI-flanges
Example to order a weld-ring gasket, profile A22N, nominal
width 10, nominal pressure 150, with a spiral wound gasket
profile SpV3N, works standard 135, of...1).

Weld-ring gasket A22N, NPS 10, Class 150, 1.4541/

SpV3N, 1.4541 (321), graphite, works standard 135.

Dimension Table WN 135, Class 150

Dimension Table WN 135, Class 300 - 600

Dimensions in mm

Dimensions in mm

DN

2*
2
3*
3
4
5
6
8
10
12
14
16
18
20
22
24

d1

52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5

d2

d3

d4

81
96
111
131
148
160
194
245
300
372
404
461
515
575
625
683

95
116
125
151
168
180
210
265
320
392
424
481
535
595
645
703

56,0
68,0
82,6
97,4
112,4
132,2
160,2
209,0
262,0
321,6
353,6
406,2
458,0
513,0
563,0
617,0

groove
d5

70
82
98
114
129
150
178
229
283
345
377
432
486
541
593
647

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,7
8,3
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
15,0

6,0
6,0
6,5
7,0
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
13,0

57
69
84
99
114
134
162
211
264
324
356
409
461
516
566
620

69
81
97
113
128
149
177
228
282
344
376
431
485
540
592
646

DN

*
1*
1*
1*
2
2
3
3
4
5
6
8
10
12
14
16
18
20
22
24

d1

20,8
26,7
35,1
40,9
52,6
62,7
78,0
90,2
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
539,7
590,5

d2

d3

d4

52
58
68
71
81
96
111
131
148
170
195
260
315
372
404
461
515
575
632
683

62
68
78
85
95
116
125
151
168
190
215
280
335
392
424
481
535
595
652
703

25,0
32,0
42,0
45,0
56,0
68,0
83,6
97,4
112,4
135,2
161,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
566,6
617,0

groove
d5

39
46
56
59
70
82
99
114
129
153
179
237
291
345
377
432
486
541
596
647

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0
15,0

5,5
5,5
5,5
6,0
6,0
6,0
6,5
7,0
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0
13,0

27
34
44
46
57
69
85
99
114
137
163
219
272
324
356
409
461
516
569
620

Dimension Table WN 135, Class 900 - 1500

Dimension Table WN 135, Class 2500

Dimensions in mm

Dimensions in mm

DN

*
*
1*
1
1*
2
2
3
4
5
6
8
10
12
14
16
18
20
24

d1

15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
590,5

d2

d3

d4

46
52
56
66
76
90
100
120
150
180
210
260
315
372
404
461
515
575
683

56
62
70
80
90
110
120
140
170
200
230
280
335
392
424
481
535
595
703

20,0
25,0
31,0
40,0
48,0
60,0
70,0
86,6
113,4
140,2
168,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
617,0

groove
d5

34
39
45
54
62
74
84
102
130
158
186
237
291
345
377
432
486
541
647

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0

5,5
5,5
6,0
6,0
6,0
6,0
6,0
6,5
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0

22
27
32
41
49
61
71
88
115
142
170
219
272
324
356
409
461
516
620

33
38
44
53
61
73
83
101
129
157
185
236
290
344
376
431
485
540
646

The dimension d1 corresponds to the inner diameter of standard ANSI

B 36.10 pipe.
1) Please specify required material in any inquiry and order.

DN

*
*
1*
1
1*
2
2
3
4
5
6
8
10
12
14
16
18
20
24

d1

15,7
20,8
26,7
35,1
40,9
52,6
62,7
78,0
102,4
128,3
154,2
202,7
254,5
304,8
336,6
387,3
438,1
488,9
590,5

d2

d3

d4

46
51
61
70
80
95
105
125
155
185
210
260
315
372
404
461
515
575
683

60
65
75
90
100
115
125
145
175
205
230
280
335
392
424
481
535
595
703

20,0
25,0
33,0
41,0
49,0
62,0
72,0
89,6
115,4
143,2
168,2
217,0
270,0
321,6
353,6
406,2
458,0
513,0
617,0

groove
d5

34
39
47
55
63
76
86
105
132
161
186
237
291
345
377
432
486
541
647

38
45
55
58
69
81
98
113
128
152
178
236
290
344
376
431
485
540
595
646

width

spiral wound
gasket
width
d6
d7

7,0
7,0
7,0
7,0
7,0
7,0
7,0
7,7
8,3
8,9
8,9
10,0
10,5
11,7
11,7
12,9
14,0
14,0
15,0

6,0
6,0
6,0
6,0
6,0
6,0
6,0
6,5
7,0
7,5
7,5
8,5
9,0
10,0
10,0
11,0
12,0
12,0
13,0

21
26
34
42
50
63
73
91
117
145
170
219
272
324
356
409
461
516
620

* Depth of turned groove t = 4 mm

For correct welding procedure, please check:
a) Sealing ledge details
b) If a flat flange is used
c) Or, if in respect to work standard WN 135, outer diameter d3
should be smaller than given.

Weld-Ring Gaskets

Dimension Table

33
38
46
54
62
75
85
104
131
160
185
236
290
344
376
431
485
540
646

11

Due to our field sales staff and our

experienced engineering consultancy
service we are familiar with all the
acute problems of our customers and
are in a position to recommend the
latest developments in sealing
technology.
For complicated gasket joints we will
calculate the necessary bolting loads.
In our comprehensive warehouse
we have a great many standard and
even non-standard dimensions
ready for you to call off.
Our stock of semi-finished goods has a
varied assortment in order to be able to
supply you as quickly as possible.

Weld-Ring Gaskets

Our special service for you

At our disposal we have up-todate machines and our experienced specialist employees in
production are the guarantee of
our high quality.

We have a documented quality assurance

system and have received certification
according to DIN EN ISO 9001.
The quality assurance measures that are
described therein are continuously
being monitored and improved.
Among others we have the following approvals:
- API Spec Q1/Spec. 6A from Third Party
for the oil industry
- RAL-GZ 719 quality seal from VGB
for soft material compensators
- Acceptance to supply for nuclear power plants

kempchen only uses tried and

tested materials, which are also
subjected to continuous inspection
in our modern chemical
and physical laboratory.

kempchen & Co. GmbH

Alleestr. 4 D - 46049 Oberhausen
Tel.: ++49 208 8482-0 Telefax ++49 208 8482-285
E-mail: [email protected]

All information and technical descriptions contained in this brochure correspond to our state
of knowledge at the time of the printing. They are intended as information about our products
and their various applications.
Therefore, we will only guarantee certain attributes described in the brochure or the
suitability for actual intended purposes according to a written express warranty in the actual
individual case. Any industrial proprietary rights must be observed. Orders will only be
accepted and completed under our standard terms and conditions, which we will make
available on request.

URL: www.kempchen.de

Gaskets Packings Expansion Joints Rubber and Plastic Parts

214e/04000003

12