CONFIDENTIAL

GX30

SERVICE MANUAL
No. S5409TQGX30/B

DIGITAL MOBILE PHONE

MODEL
E : For U.K. R : For Ireland S : For Spain EP: For U.K. (Prepaid) W : For Sweden D : For Greece Z : For New Zealand L : For Malta C : For Switzerland U : For Belgium

GX30

(INTERNAL MODEL NAME: TQ-GX30E/G/R/T/S/H/EP/PP/W/B/D/A/Z/Q/L/F/C/K/U)

G : For Germany T : For Italy H : For Netherlands PP: For Portugal (Prepaid) B : For Hungary A : For Australia Q : For Egypt F : For France K : For Austria

In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. Caution Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction.

CONTENTS
SERVICING CONCERNS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ......................................... ........ 1-1 [2] Names of parts....................................... ........ 1-2 [3] Operation manual .................................. ........ 1-3 CHAPTER 2. ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE [1] SHARP Program Support Tool (SPST).. ........ 2-1 [2] Test points.............................................. ...... 2-44 [3] Troubleshooting ..................................... ...... 2-48 CHAPTER 3. DISASSEMBLY AND REASSEMBLY [1] Servicing Concerns................................ ........ 3-1 [2] Disassembly and reassembly ................ ........ 3-4 CHAPTER 4. DIAGRAMS [1] Block diagram................................................ 4-1 CHAPTER 5. SCHEMATIC DIAGRAM AND WIRING SIDE OF P.W.BOARD [1] Notes on schematic diagram......................... 5-1 [2] Types of transistor and LED .......................... 5-1 [3] Waveforms of circuit ...................................... 5-2 [4] Schematic diagram/ Wiring side of P.W.Board ............................. 5-5 CHAPTER 6. OTHERS [1] Function table of IC ....................................... 6-1 [2] Function table of Camera ............................ 6-27 [3] Function table of Display ............................. 6-28 Parts Guide

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

GX30

CONFIDENTIAL

GX30 Phone Service E Market ManualCONCERNS SERVICING

1. When requested, back-up users handset data using SPST (SHARP Program Support Tool). Otherwise, before servicing, warn the user that data in the memory may be lost during repairs. 2. Upgrade the firmware to the latest version using SPST before returning the handset to the customer. 3. After repairs, inspect the handset according to the following flowchart. Repairs are completed. (Fixed parts have been checked for proper operation.)

Check IMEI NO./Operator code (Destination)/ Firmware version by Identity function of SPST.

Inspect each device using performance check adjustment function of SPST.

Carry out RF performance check with SPST.

All completed. 4. When storing or transporting a PWB, put it into a conductive bag or wrap it in aluminum foil. (C-MOS IC may be damaged by electrostatic charges.) 5. Do not leave fingerprints, etc. on ornamental parts including a cabinet, especially clear windows for main and sub displays. Wear fingerstalls to avoid this. Also, ensure not to leave fingerprints on the surface of main and external display panels. 6. To prevent oxidation which causes connection problems, do not touch any terminals on the electric board, microphone, vibrator, earpiece and speaker. When handling these parts, wear fingerstalls. Should you touch these parts, clean them with a soft dry cloth. Always wear fingerstalls when handling a shield case on the electric board. Otherwise oxidation may occur causing handset performance deterioration. 7. The FPC is a precision device. Handle it carefully to prevent any damages. 8. Do not expose the moisture sensor to liquids. If the sheet gets wet, red ink runs. In this case, replace the sheet with a new one. Be careful about your perspiration. 9. Before you disassemble or reassemble handset, make sure to remove the Li-Ion battery. 10.Be sufficiently careful with static electricity of integrated circuits and other circuits. Wear static electricity prevention bands while servicing.

CONFIDENTIAL GX30 Phone Service E Market Manual 1. GENERAL DESCRIPTION CHAPTER

FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.

GX30

[1] Specifications
General: Quad - band (GSM 850 MHz/GSM 900 MHz/ DCS 1800 MHz/PCS 1900MHz) GPRS-enabled WAP, MMS, SMS Sound: Mobile light: External DC supply voltage: Battery: Standby time: Talk time: Others: 40-polyphonic ring melodies 7 colours 5.2 V 3.7 V, 780 mAh, Li-Ion 100 ~ 250 hours 160 ~ 240 min. Side key Infrared port 1.2 L/P (maximum distance 20 cm) Connector for AC charger and data cable Standard hands free connector (2.5)

Dimensions (folded, excluding the aerial) (H x W x D): Weight: Battery operating temperature: Main display:

95 x 49 x 26 mm 110 g

0C - 40C Display dimensions: 240 x 320 pixels LCD display: CGS 262,144 colours with backlight LCD back light: LED back light white colour LEDs External display: Display dimensions: 64 x 96 pixels LCD display: STN 65,536 colours LCD with back light Camera: CCD 1M pixels built-in camera Zoom: Wide and zoom mode [Supported 20 (when image size is 160 x 120 pixels) x zoom] Lens: F2.8, f = 3.7 mm

Battery running time depends on the battery and SIM card as well as the network conditions and usage

Specifications for this model are subject to change without prior notice.

Powered by JBlend TM Copyright 19972003 Aplix Corporation. All rights reserved. JBlend and all JBlend-based trademarks and logos are trademarks or registered trademarks of Aplix Corporation in Japan and other countries.

Powered by Mascot Capsule /Micro3D Edition TM R Mascot Capsule is a registered trademark of HI Corporation C 2002-2003 HI Corporation. All Rights Reserved. Licensed by Inter Digital Technology Corporation under one or more of the following United States Patents and/or their domestic or foreign counterparts and other patents pending, including U.S. Patents: 4,675,863: 4,779,262: 4,785,450 & 4,811,420. Licensed under U.S. Patent 4,558,302 and foreign counterparts.

T9 Text Input is licensed under one or more of the following: U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, and 6,011,554; Australian Pat. No. 727539; Canadian Pat. No. 1,331,057;United Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No. HK0940329; Republic of Singapore Pat. No. 51383; Euro. Pat. No. 0 842 463 (96927260.8) DE/DK, FI, FR, IT, NL,PT.ES,SE,GB; Republic of Korea Pat. Nos. KR201211B1 and KR226206B1; and additional patents are pending worldwide.

SD logo

is a trademark.

Bluetooth is a trademark of the Bluetooth SIG, Inc.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sharp is under license. Other trademarks and trade names are those of their respective owners. CP8 PATENT

11

GX30

CONFIDENTIAL

[2] Names of parts

1

8 2 3

20 15 16 17 18 21 22 23 27 19

24 25 26

4 5 6 7

9 10 11 12 13 14

1. Earpiece 2. Navigation Keys (Arrow Keys): Moves cursor to select menu items, etc. , , , in this manual indicate these keys. Up/Down arrow keys: Displays Contacts List entries in stand-by mode. Left arrow key: Displays list of Applications in stand-by mode. Right arrow key: Displays Pictures screen in stand-by mode. 3. Centre Key: Displays Main menu in stand-by mode and executes functions. in this manual indicates this key. 4. Left Soft Key: Executes the function at the bottom left of the screen. in this manual indicates this key. 5. Send Key: Makes or accepts calls, views the call in stand-by mode. 6. Voice Mail Key: Press and hold this key to connect to the Voice mail centre automatically. (Depends on the SIM card.) 7. * /Shift Key, Viewfinder Switch Key: Switches character case among four modes: Abc, ABC, 123 and abc. Switches viewfinders between main display and external display in digital camera/video camera mode. 8. Main Display 9. Right Soft Key: Executes the function at the bottom right of the screen. in this manual indicates this key. Used to access Vodafone live! by opening the browser in stand-by mode. 10.End/Power Key: Ends a call, turns power on/ off.

11.Camera Key: 12.Keypad 13.#/Flash light Key:

Starts the digital camera in stand-by mode. Switches symbol screens. Press and hold this key to shift text input method between multi-tap and T9 mode. Turns the flash/auxiliary light on or off in digital camera/video camera mode.

14.Microphone 15.Aerial 16.Camera 17.Speaker 18.Mobile Light:

Used as a flash or an auxiliary light in digital camera/video camera mode, as a battery charge indicator, or notification for incoming calls, data/fax calls or messages. Sends and receives data via infrared.

19.External Display 20.Infrared Port:

21.RF Connector 22.Side-Up/Side-Down Keys: Moves cursor to select menu items, adjusts earpiece volume, etc. In stand-by mode, press and hold this key to turn the mobile light on and off. When the mobile light is on, press this key to change the light colour. 23.Battery Cover 24.Macro Switch: Switches between normal (Close-up) ( ) and macro ( ) position. 25.Handsfree Kit Connector 26.Memory Card Slot Cover 27.External Connector: Used to connect either the charger or USB data cable.

12

CONFIDENTIAL
[3] Operation manual
(Page numbers refer to the user guide)

GX30

[Optional Accessories]
Spare Lithium-ion battery (XN-1BT30) High capacity Lithium-ion battery (XN-1BT31) Cigarette lighter charger (XN-1CL30) USB data cable (USB cable: XN-1DC30) AC charger (XN-1QC30, XN-1QC31, XN-1QC32) Personal handsfree kit (XN-1ER20) The above accessories may not be available in all regions. For details, please contact your dealer.

[Quickstart Guide]

13

GX30

12

CONFIDENTIAL

14
New Messages Download Games News Sport

CONFIDENTIAL

GX30

6-3-3

1-3

15

7-5

GX30
MEMO

CONFIDENTIAL

16

GX30 CONFIDENTIAL GX30 Phone Service E Market Manual 2. ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE CHAPTER UPGRADE
SPST (SHARP Program Support Tool) allows you to adjust settings, conduct performance checks, and upgrade the firmware.

[1] SHARP Program Support Tool (SPST)

1. System requirements
IBM PC compatible personal computer (standard COM1 115,200 bps serial port and USB required) Supported OS: Windows 98/98SE/2000/XP (except for Windows 95/ME/NT) (English, German, Italian, Spanish, French and Chinese versions) Data cable

<During RF adjustment> GSM tester: CMU200 GPIB interface: National Instruments USB-GPIB cable (Model No.: NI GPIB-USB-B)

2. Introduction
2.1. Functions
SPST offers seven key functions: 1) Firmware download 2) User data transfer (processes all data at once but not individually.) 3) RF calibration check and test 4) Default setting 5) Identification 6) Performance check and adjustment 7) User password reset

2.2. Installation
1. Use Windows Explorer to execute the setup.exe file on the CD-ROM. 2. The SPST GX30 setup wizard appears. Follow the installation instructions. 3. After the installation is complete, shortcuts to SPST are created on the desktop and under the Start Programs GX30 menu. Start SPST from the shortcuts.

21

GX30
2.3. Starting up

CONFIDENTIAL

Connect GX30 to an operable serial port of the PC with the supplied data cable. Make sure that the battery is fully charged. Start SPST from the desktop. 1. The Input password dialog box appears. Enter the password, select a port where GX30 is connected from the list box, and click OK. If you do not know SPC, click Cancel to exit.

Figure 1 2. To change the password, enter the current password in figure 1, and then click Change Password.

Figure 2 3. To check the usage status of tools, click Show Repair Log in figure 1. 4. Click Downloader for Emergency.

Figure 3 The above screen appears. Select a model to use and execute the Downloader. (Use this to initialize the flash, etc.)

22

CONFIDENTIAL
5. When the password is correct, a connection is established and the following screen appears.

GX30

Refer to the attachment 1 for the destination and operator name.

Software version: A02-006-0184-GX30

Figure 4 Buttons Default Set User Data Back-up User Data Restore Downloader RF Calibration & Check RF Test User Password Reset Performance check adjustment **** mode release Exit Refer to 4.1. Default setting. (see page 2-5) Refer to 4.2. User data back-up. (see page 2-6) Refer to 4.3. User data restore. (see page 2-7) Refer to 4.4. Downloader. (see page 2-8) Refer to 4.5. RF calibration & check. (see page 2-19) Refer to 4.6. RF test tool. (see page 2-28) Refer to 4.7. Password reset. (see page 2-34) Refer to 4.8. Performance check and adjustment. (see page 2-35) Refer to 4.9. ****mode release. (see page 2-42) End SPST.

Attachment 1 Destination and Operator name Chart No. 01 02 03 04 05 06 08 10 11 12 13 14 15 16 17 18 19 48 50 Operator name Vodafone UK Airtel SFR Vodafone Omnitel D2 Vodafone NL Vodafone Ireland Vodafone Greece Vodafone Hungary Vodafone Australia Vodafone New Zealand Vodafone Sweden Vodafone Egypt Vodafone Malta Swisscom mobilkom austria Belgacom mobile Vodafone PT Vodafone UK Country UK Spain France Italy Germany Netherlands (Holland) Ireland Greece Hungary Australia New Zealand Sweden Egypt Malta Switzerland Austria Belgium Portugal UK Model name A4TQGX30E A4TQGX30S A4TQGX30F A4TQGX30T A4TQGX30G A4TQGX30H A4TQGX30R A4TQGX30D A4TQGX30B A4TQGX30A A4TQGX30Z A4TQGX30W A4TQGX30Q A4TQGX30L A4TQGX30C A4TQGX30K A4TQGX30U A4TQGX30PP A4TQGX30EP

Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Post-Paid Pre-Paid Pre-Paid

23

GX30
3. Adjustments for GX30

CONFIDENTIAL
) Main display flicker adjustment External display contrast adjustment White defect correction Black defect correction

1. Adjustments are required after replacing the following parts. ( Parts Temperature adjustment (Camera) Temperature adjustment (Battery)

TH101 TH701 Main display unit External display unit Camera unit When replacing other parts in the RF section, carry out RF calibration. 2. Click the buttons on the SPST screen for adjustments.

RF calibration

To adjust the device, click this button (Performance check adjustment).

Figure 5 3. The following screen appears.

Temperature adjustment (Camera section) Temperature adjustment (Battery section) Main display flicker adjustment External display contrast adjustment White defect correction Black defect correction
Figure 6

24

CONFIDENTIAL
4. Functions
4.1. Default setting
SPST can restore the factory settings. This function 1. Deletes all user data in the file system; 2. Restores all WAP settings to default; and 3. Restores the values set by the user to default; (MEP_LOCK settings and the destination and operator name do not change.) <Operation> 1) Set the COM port on the SPST initial screen and click Default Set. 2) Click Yes to proceed. Click No to exit.

GX30

Figure 7 3) Click Yes to back-up the MEPLOCK data. Click No to restore default settings.

Figure 8 4) Communication starts.

Figure 9 5) The following appears when you select Yes in step 3 and MEPLOCK data exists. Click Yes to restore the data.

Figure 10

25

GX30

CONFIDENTIAL

6) After the handset is turned on, the initialization is complete.

Figure 11

4.2. User data back-up

SPST saves all the data stored on the handset. 1. Set the COM port on the SPST initial screen and click User Data Back-up. 2. Specify the file name in the following dialog box and click Save.

Figure 12 3. The communicating dialog box appears while processing.

Figure 13 4. When completed, the following message appears. Click OK.

Figure 14

26

CONFIDENTIAL
4.3. User data restore
SPST completely restores the backed up data. 1. Set the COM port on the SPST initial screen and click User Data Restore. 2. Specify the file name in the following dialog box and click Save.

GX30

Figure 15 3. The communicating dialog box appears while processing.

Figure 16 4. When the restore is complete, click OK.

Figure 17

27

GX30
4.4. Downloader 4.4.1 Introduction
Downloader allows you to upgrade the firmware.

CONFIDENTIAL

1) Required devices
The following devices are required to rewrite MOT files using Communication Box. Conversion connector (16-pin 10-pin) This conversion connector is required to connect GX30 with Communication Box since the cable connector of Communication Box has 16 pins.

Figure 18

2) Connecting handset to a PC
A) Using a cable for upgrading 1. Connect the cable to a PC. 2. Connect the cable to handset. 3. The photo below shows handset connected to a PC.

Figure 19 B) Using Communication Box 1. Connect a PC to Communication Box via a serial cable. 2. Connect the AC charger to Communication Box and then plug it into the outlet. All SET POWER SW on Communication Box must be turned off. 3. Connect the conversion connector to Communication Box Cables. Connect the conversion connector in the following order, label side up. From upper right end: Cable No. 1, 3, 5, 7, and 9. From lower right end: Cable No. 2, 4, 6, 8, and 10.

Figure 20

28

CONFIDENTIAL
4. The photo below shows the conversion connector connected to Communication Box Cable 1.

GX30

Figure 21 5. Connect the other end of the conversion connector to handset.

Figure 22 6. The photo below shows handset, Communication Box and a PC (all connected). Make sure handset and Communication Box Cable 1 are connected via the conversion connector.

Figure 23 [Note] Handset must be turned off before making any connections. Press and hold the Power key to turn off handset. Do not turn off in other ways. Malfunction may occur and the MOT file rewrite operation may fail. Make sure the handset battery is sufficiently charged. If the battery is low, the MOT file rewrite operation may fail. Charge the battery before the operation. Disconnect the AC charger from a cable for upgrading. When rewriting MOT files using the upgrading tool, do not connect the AC charger to the cable. If you connect the cable connected to the AC charger to handset, charging starts and the MOT file rewrite operation is interrupted. All SET POWER SW on Communication Box must be turned off. If handset is connected with SET POWER SW turned on, charging starts and the MOT file rewrite operation is interrupted. Make sure handset and Communication Box Cable 1 are connected via the conversion connector. (When using Communication Box, the only handset connected to Cable 1 can be operated on the PC.)

29

GX30
4.4.2 Rewriting MOT files

CONFIDENTIAL

This section describes how to rewrite MOT files using the upgrading tool.

1) Activating Software
1. Double click the shortcut icon on your desktop or click The GX30 Upgrading Tool on the Start menu.

Figure 24 2. The upgrading tool is activated.

Figure 25 [Note] Disable the power saving mode before rewriting MOT files. If the power saving mode is active, the rewrite operation may fail depending on the PC.

2 10

CONFIDENTIAL
2) Selecting options and COM port
1. Uncheck the check box when using a cable for upgrading. Leave it checked when using Communication Box.

GX30

2. To initialize user area, check the File System Initialize check box. (User data will be deleted and the handset status will return to the default.) 3. Click here and in the pull-down list, select a communications port where the cable or Communication Box is connected.

1 2

Figure 26 When using Communication Box, set Wait Time. Check the Communication Box check box to adjust Wait Time (default: 8 seconds). The time to delete the program data varies between handsets. Handsets wait for the set Wait Time until the whole process is completed. If an error occurs, increase the value.

Figure 27 [Notes for the Wait Time setting] When the set value is smaller than the default (8), the message on the left appears alerting you a possible error. Click the OK button to proceed, and click the Cancel button to change the value.

Figure 28

2 11

GX30

CONFIDENTIAL

You can shorten time for the MOT file rewrite operation by selecting a smaller value for Wait Time. Example: Time to rewrite two MOT files at a time. At the default setting (8 seconds), rewrite time is approximately one hour. If the value is set to 1, the rewrite time will be reduced to approximately 30 minutes. If an error occurs at 1, increase the value. The error screen will appear on handsets No. 2 to No.10. If this screen appears, increase Wait Time and retry.

Error screen
Flash Loader 5.02 CORRESPONDENCE_ERROR

Figure 29 When the File System Initialize check box is checked, a confirmation message appears.

Click the [OK] button.

Figure 30 [Note] When you check File System Initialize check box and click the OK button, handset status returns to the default. In this case, user data is initialized after the MOT file rewrite operation. Uncheck the check box to avoid this.

2 12

CONFIDENTIAL
3) Selecting a MOT file
1. Click the Select File button. The Open dialog box appears.

GX30

Figure 31 [Open dialog box] 2. Click the button to open a desired folder.

3. A Motorola file (.mot) in the folder appears. Click a file to write in. 4. Click the Open button to open the file.

Figure 32 [Note] Make sure to select a MOT file. If the File name field is blank, you cannot rewrite a MOT file. Use MOT files in the hard disk. If the selected MOT file is stored in other locations, an error message appears and you cannot complete the rewrite operation.

Figure 33 To use MOT files on CDs or on the network, copy or download them to the hard disk first.

2 13

GX30
4) Rewriting a MOT file
Click the Start Loading Flash button to start rewriting.

CONFIDENTIAL

Figure 34 1. Press Power Button appears. <When using a cable for upgrading> Hold down the Power key. <When using the Communication Box> Turn on handsets from No.10 down to No.1 (turn on only the handsets you are using).

Figure 35 2. Keep Pressing Power Button appears. <When using a cable for upgrading> Hold down the Power key until the Keep Pressing Power Button disappears. <When using the Communication Box> Leave the handsets turned on.

Figure 36

2 14

CONFIDENTIAL
3. The MOT file rewrite operation starts. <When using a cable for upgrading> When Keep Pressing Power Button disappears, release the Power key. <When using the Communication Box> Leave the handsets turned on.

GX30

Figure 37 4. When the rewrite operation starts, handset display screen shows the software version and process of communications with the PC.

Flash Loader 5.02

XXXXXXXCommand

Figure 38 Canceling the ongoing rewrite operation: Click the QUIT button. To rewrite MOT files later, remove and install the battery first. [Notes for the use of a cable for upgrading] 1. Disconnect the AC charger from the cable. Otherwise charging starts and the MOT file rewrite operation is interrupted. 2. Make sure the handset battery is sufficiently charged. If the battery is low, the rewrite operation may fail. Charge the battery before the operation. 3. If the ongoing rewrite operation is canceled, or interrupted by an error, remove and reinstall the battery and retry. [Notes for the use of the Communication Box] 1. When Press Power Button! appears, turn on handsets from No.10 down to No.1. If the handset No.1 is first turned on, the rewrite on handsets No. 2 to No. 10 operation will fail. 2. The time to delete the program data varies between handsets. If the process fails at the default Wait Time (8 seconds), increase the value. Consequently, this will increase the time to complete the rewrite operation.

2 15

GX30
5) Checking the value of SUM

CONFIDENTIAL

When the rewrite operation is completed, a confirmation message appears with SUM.

Figure 39 SUM also appears on handset. <When using a cable for upgrading> After 8 seconds, SUM disappears. <When using Communication Box> When SET POWER SW is turned off, SUM disappears.

Flash Loader 5.02 SUM Check End SUM = 0xdb3d

Figure 40 Make sure SUM is the same between the PC and handset. The same SUM means that the rewrite operation is completed properly. If the value is different, try again to ensure completion of the operation.

If the MOT file rewrite operation fails, an error message appears on handset. * The screen shot on the left shows an error in erasing Flash data. ADR and STR appear only when an error occurs in the FLASH-related operation. Start over the MOT file rewrite operation. <When other error messages appear> Find the message in [4.4.3.2) Error messages for Loading loader (see page 2-18)], and follow the instructions.

Error screen
Flash Loader 5.02 FLASH_ERROR ERROR_ERASE ADR = 0x1000000 STR = 0xA0

Figure 41

2 16

CONFIDENTIAL
6) After the operation
Disconnect the cable for upgrading from handset. When using the Communication Box, turn off SET POWER SW and then disconnect the cable from handset.

GX30

7) Initializing only the file system

Follow the instructions below to initialize only the file system. (User data will be deleted and the handset status will return to the default.) * Perform this procedure when the handset does not turn on. 1. Check the File System Initialize check box. 2. Leave the Load File text box blank. 3. Click the Start Loading Flash button.

2 3

Figure 42 For further operations, refer to [4.4.2.4) Rewriting a MOT file (see page 2-14)] or [4.4.2.5) Checking the value of SUM (see page 2-16)].

2 17

GX30
4.4.3 Error message list

CONFIDENTIAL

Below is the list of error messages for the upgrading tool (on the PC side) and Loading loader (on the handset side).

1) Error messages for the upgrading tool (on the PC side)

No. 1 2 3 4 5 Message Select a file for Downloading or check the box of Initializing. Unable to open file. You need to set the Wait Time! The file you selected is unsuitable for Upgrading. Cannot Setup COM port. Descriptions/Instructions Load File is not set. Select a MOT file. Failed to open the MOT file. Start over the rewrite operation. WaitTime (S) is not set. Set WaitTime (S) value. The selected file cannot be rewritten for upgrading. Select an appropriate MOT file. The selected COM port does not exist or is used for other operations. Select a COM port connected to the PC cable. No response from Loading loader. Start over the rewrite operation. Information sent from the PC is illegal. Reinstall the upgrading tool. Start over the rewrite operation. Failed to initialize FLASH ROM in (XXXX). Start over the rewrite operation. Undefined response from Loading loader. Start over the rewrite operation.

6 7

RAM Loader not responding to Commands. RAM Loader responding Parameter Error.

8 9

RAM Loader responding Flash Error (XXXX). Correspondence Error.

2) Error messages for Loading loader (on the handset side)

No. 1 2 FLASH_ERROR ERROR_PARAM Message Descriptions/Instructions An error in Flash Rom. Start over the rewrite operation. The upgrading tool is damaged. Uninstall and reinstall the upgrading tool, and start over the rewrite operation. Flash Rom is protected. Battery may be too low. Use a sufficiently charged battery and start over the rewrite operation. Failed to read Flash Rom data and the operation was aborted. Start over the rewrite operation. Failed to write to Flash Rom and the operation was aborted. Start over the rewrite operation. Failed to erase Flash Rom data and the operation was aborted. Start over the rewrite operation. The rewrite operation was aborted since there was a mismatch between data written to Flash Rom and that written to handset. Start over the rewrite operation. Communication was terminated since there was no response from Flash Rom for a certain period of time. Start over the rewrite operation. Communication was terminated since serial data communication failed. Start over the rewrite operation. Indicates the address of Flash (the error source). Indicates the status of Flash (the error source).

ERROR_WPROTECT

4 5 6 7

ERROR_READ ERROR_WRITE ERROR_ERASE ERROR_VERIFY

ERROR_RWE_TMOUT

CORRESPONDENCE_ERROR

10 11 *

ADR = XXXXXXXX STR =XX

When No.1 occurs, handset screen shows error messages for No.2 to No.8 as well as the address (No.10) and status (No.11) of the error source at the same time.

2 18

CONFIDENTIAL
4.5. RF calibration & check

GX30

Stabilized power supply

RF cable

Handset

GSM tester

Test battery

GPIB cable

Data cable

PC
Figure 43

4.5.1 Preparation
Connect PC and GSM tester with a GPIB cable. Connect PC and handset with a Data cable. (Use a test battery or one close.) Connect a RF cable of GSM tester to handset.

2 19

GX30
4.5.2 Default setting for the program.
Activate the program and set defaults.

CONFIDENTIAL

1) Select the COM port.

2) Set the GPIB No.

3) Select the test instrument. 4) Set the GPIB address.

5) Set the "Cable Offset" values. For cables with connector QCNWK0138AFZZ/ QCNWK0136AFZZ, set the values as follows: GSM 900: 0.60 DCS 1800: 0.95 PCS 1900: 0.96 GSM 850: 0.60 6) Auto Dial Setting When the Auto Dial check box is checked, an entered number is automatically dialed for performance check. 7) Number Setting Enter a number for Auto Dial.
Figure 44

2 20

CONFIDENTIAL
4.5.3 RF calibration
1. Apply 4 V using a stabilized power supply and turn on the handset. 2. Start RF calibration & check on SPST and click Calibration. 3. When initialization is complete, click OK.

GX30

Figure 45 4. Apply 4 V using a stabilized power supply and turn on the handset. After the handset enters Standby mode, lower the voltage to 3.7 V, click OK.

Figure 46 5. Make sure the handset is on and click OK. (Adjustment starts.)

Figure 47 6. Click OK.

Figure 48 7. The initial screen returns.

<Note> The following appears when the handset software (mot) is outdated. Upgrade to a new version.

Figure 49

2 21

GX30
4.5.4 RF performance check

CONFIDENTIAL

1. Apply 4 V using a stabilized power supply and turn on the handset. 2. Start RF calibration & check on SPST and click Check. 3. When initialization is complete, click OK.

Figure 50 4. Apply 4 V using a stabilized power supply and turn on the handset. After the handset enters Standby mode, lower the voltage to 3.7 V, enter the PIN code and click OK.

Figure 51 5. Make sure the handset is in the idle mode and click OK.

Figure 52 6. RF performance check is complete. Click Save As... and name the file to save the result. Click OK to exit.

Figure 53

2 22

CONFIDENTIAL
The following will be displayed in case of failure. See the attachment 2 for troubleshooting.

GX30

Figure 54 7. Click OK.

Figure 55 8. The initial screen returns.

2 23

GX30
Attachment 2 Whole inspection list by RF performance check. Band Sending/ Recei ve Tx No. Item to be inspected Channel

CONFIDENTIAL
Band PCL Sending/ Recei ve No. Item to be inspected Channel PCL

GSM 900

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Burst Power Burst Power Burst Power Burst Power Burst Power Frequency Error Frequency Error Frequency Error Phase Error (RMS) Phase Error (RMS) Phase Error (RMS) Phase Error (Peak) Phase Error (Peak) Phase Error (Peak) Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200

37CH 975CH 124CH 37CH 37CH 37CH 975CH 124CH 37CH 975CH 124CH 37CH 975CH 124CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH

PCL5 PCL5 PCL5 PCL11 PCL19 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19

Rx

DCS

Tx

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122

Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Burst Timing Burst Timing Burst Timing Burst Timing Burst Timing Rx Sensitivity Rx Sensitivity Rx Sensitivity Usable Receiver Level Rx Level Reports Burst Power Burst Power Burst Power Burst Power Burst Power Frequency Error Frequency Error Frequency Error

37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 975CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 124CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 37CH 975CH 124CH 37CH 37CH 37CH 975CH 124CH 37CH 37CH 699CH 512CH 885CH 699CH 699CH 699CH 512CH 885CH

PCL19 PCL19 PCL19 PCL19 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL5 PCL5 PCL5 PCL11 PCL19 PCL5 PCL5 PCL5 PCL5 PCL5 PCL0 PCL0 PCL0 PCL5 PCL15 PCL0 PCL0 PCL0

2 24

CONFIDENTIAL
Band Sending/ Recei ve No. Item to be inspected Channel PCL Band Sending/ Recei ve No. Item to be inspected Channel

GX30
PCL

123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184

Phase Error (RMS) Phase Error (RMS) Phase Error (RMS) Phase Error (Peak) Phase Error (Peak) Phase Error (Peak) Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600

699CH 512CH 885CH 699CH 512CH 885CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH

PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0

Rx

PCS

Tx

185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246

Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Burst Timing Burst Timing Burst Timing Burst Timing Burst Timing Rx Sensitivity Rx Sensitivity Rx Sensitivity Usable Receiver Level Rx Level Reports Burst Power Burst Power Burst Power Burst Power Burst Power Frequency Error Frequency Error Frequency Error Phase Error (RMS) Phase Error (RMS) Phase Error (RMS) Phase Error (Peak) Phase Error (Peak) Phase Error (Peak) Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250

699CH 699CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 885CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 699CH 512CH 885CH 699CH 699CH 699CH 512CH 885CH 699CH 699CH 661CH 512CH 810CH 661CH 661CH 661CH 512CH 810CH 661CH 512CH 810CH 661CH 512CH 810CH 661CH 661CH 661CH 661CH

PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL0 PCL0 PCL0 PCL5 PCL15 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL5 PCL15 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0

2 25

GX30
Band Sending/ Recei ve No. Item to be inspected Channel

CONFIDENTIAL
PCL Band Sending/ Recei ve No. Item to be inspected Channel PCL

247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308

Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800

661CH 661CH 661CH 661CH 661CH 661CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 810CH 810CH 810CH 810CH 810CH 810CH 810CH 810CH 810CH 810CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH 512CH

PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0

Rx

GSM 850

Tx

309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370

Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Burst Timing Burst Timing Burst Timing Burst Timing Burst Timing Rx Sensitivity Rx Sensitivity Rx Sensitivity Usable Receiver Level Rx Level Reports Burst Power Burst Power Burst Power Burst Power Burst Power Frequency Error Frequency Error Frequency Error Phase Error (RMS) Phase Error (RMS) Phase Error (RMS) Phase Error (Peak) Phase Error (Peak) Phase Error (Peak) Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250

810CH 810CH 810CH 810CH 810CH 810CH 810CH 810CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 661CH 512CH 810CH 661CH 661CH 661CH 512CH 810CH 661CH 661CH 190CH 128CH 251CH 190CH 190CH 190CH 128CH 251CH 190CH 128CH 251CH 190CH 128CH 251CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 128CH 128CH 128CH 128CH

PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL0 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL5 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL15 PCL0 PCL0 PCL0 PCL5 PCL15 PCL0 PCL0 PCL0 PCL0 PCL0 PCL7 PCL7 PCL7 PCL11 PCL19 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7

2 26

CONFIDENTIAL
Band Sending/ Recei ve No. Item to be inspected Channel PCL Band Sending/ Recei ve No. Item to be inspected Channel

GX30
PCL

371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415

Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Mod_spectrum 800 Mod_spectrum 600 Mod_spectrum 400 Mod_spectrum 250 Mod_spectrum 200 Mod_spectrum +200 Mod_spectrum +250 Mod_spectrum +400 Mod_spectrum +600 Mod_spectrum +800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800

128CH 128CH 128CH 128CH 128CH 128CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 128CH

PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 Troubleshooting list Check parts for DCS IC802, FL803, FL905 TCX801 IC801 IC801, TCX801 IC801, IC802 IC802 IC801, FL803, FL902, FL905 IC801 IC801, FL803, FL902, FL905

Rx

416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456

Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Switch_Spectrum 1800 Switch_Spectrum 1200 Switch_Spectrum 600 Switch_Spectrum 400 Switch_Spectrum +400 Switch_Spectrum +600 Switch_Spectrum +1200 Switch_Spectrum +1800 Burst Timing Burst Timing Burst Timing Burst Timing Burst Timing Rx Sensitivity Rx Sensitivity Rx Sensitivity Usable Receiver Level Rx Level Reports

128CH 128CH 128CH 128CH 128CH 128CH 128CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 251CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 190CH 128CH 251CH 190CH 190CH 190CH 128CH 251CH 190CH 190CH

PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL7 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL11 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL19 PCL7 PCL7 PCL7 PCL11 PCL19 PCL7 PCL7 PCL7 PCL7 PCL7

Tx

Rx

Test item Burst Power Frequency Error Phase Error Mod_spectrum Switch_Spectrum Burst Timing Rx Sensitivity Usable Receiver Level Rx Level Reports

Check parts for GSM900 IC802, FL803, FL905 TCX801 IC801 IC801, TCX801 IC801, IC802 IC802 IC801, FL803, FL902, FL904, FL905 IC801 IC801, FL803, FL902, FL904, FL905

Check parts for PCS IC802, FL803, FL905 TCX801 IC801 IC801, TCX801 IC801, IC802 IC802 IC801, FL803, FL903, FL905 IC801 IC801, FL803, FL903, FL905

Check parts for GSM850 IC802, FL803, FL905 TCX801 IC801 IC801, TCX801 IC801, IC802 IC802 IC801, FL803, FL901, FL904, FL905 IC801 IC801, FL803, FL901, FL904, FL905

2 27

GX30
4.6. RF test tool 4.6.1 Requirements

CONFIDENTIAL

For repairs, this test checks the condition of an electric board (especially the RF section). PC with COM port GX30 Data Cable PWB repair jig GSM Tester (CMU200)

4.6.2 Setup
1. Set PWB and make connections as shown in Figures 56 and 57. Make sure connections are correct at the points shown in Figure 58.

Hook

Hook

Hook

PWB

Hook

Hook

Hook

Figure 56 PWB installation

2 28

CONFIDENTIAL

GX30

Black

Red

GSM Tester (CMU 200)

PC

PWB repair jig

Data Cable
Figure 57 Connections

Points

Figure 58 Contact points

2 29

GX30

CONFIDENTIAL

2. Apply 4 V using a stabilized power supply and turn on the handset.

Push

Figure 59 Turning power on 3. Start RF test tool. 4. Select a COM port to which Data Cable is connected. (Figure 60) 5. Press the Initialize & Read Data button. (Figure 60)

Figure 60 6. Figure 61 appears (wait a few seconds).

Figure 61 7. Click OK to proceed.

2 30

CONFIDENTIAL
4.6.3 Tests 1) BAND Select & Channel
Select a band and a channel to test. Settings are applied to all tests.

GX30

Input box Band selection

Channel bar
Figure 62 [Procedure] 1. Select a band. (GSM850, GSM900, DCS or PCS) 2. Select or enter a channel using Channel bar or Input box.

2) TX test
Test burst transmission.

TX frequency of selected channels

Current PCL (Read only)

PCL bar TX ON/OFF button

Data patterns

This indicator appears during burst transmission.

Figure 63 [Procedure] 1. Select a band and channel. [see 4.6.3.1)] 2. Select PCL (Power Control Level) using PCL bar. 3. Select Data pattern. 4. Click TX ON to start burst transmission. (You can check each part in this state.) 5. Click TX OFF to end burst transmission.

Data pattern (TSC 5) includes Training Sequence GSM 5, and other part is pseudo random data.

2 31

GX30
GX30 TX power Table (25C, voltage: 3.7[V]) GSM850 Band PCL GSM850 [dBm] 7 29 8 27 9 25 10 23 11 21 12 19 13 17 14 15 15 13 16 11 17 9 18 7 19 5 Tolerance +/2 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/5 dB +/5 dB +/5 dB +/5 dB

CONFIDENTIAL
GSM900 Band PCL GSM900 [dBm] 5 33 6 31 7 29 8 27 9 25 10 23 11 21 12 19 13 17 14 15 15 13 16 11 17 9 18 7 19 5 Tolerance +/2 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/5 dB +/5 dB +/5 dB +/5 dB DCS/PCS Band PCL DCS/PCS [dBm] 0 30 1 28 2 26 3 24 4 22 5 20 6 18 7 16 8 14 9 12 10 10 11 8 12 6 13 4 14 2 15 0 Tolerance +/2 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/3 dB +/4 dB +/4 dB +/4 dB +/4 dB +/4 dB +/5 dB +/5 dB

3) RX test
The handset receives burst signals in this test.

RX frequency of selected channels

Current RX Gain (Read only)

RX Gain Setting bar RX ON/OFF button

Sniff ON/OFF

This indicator appears while receiving burst signals.

Figure 64 [Procedure] 1. Select a channel and band. [see 4.6.3.1)] 2. Select RX Gain using RX Gain Setting bar. 3. Choose Sniff ON or OFF. 4. Click RX ON to start receiving burst signals. 5. From GSM tester, send burst signals in the specified channel. (You can check each part in this state.) 6. Click RX OFF to end receiving burst signals.

* *

In this test, the reception timing cannot be synchronized with burst signals from Signal Generator or GSM tester. The standard RX Gain Setting is: (Input power at the aerial connector of the handset) + (RX Gain) = 16 dBm Excessive Input power or RX Gain may cause damage to the handset.

2 32

CONFIDENTIAL
4) RSSI Measure
The handset notifies you of input power value at the aerial connector.

GX30

Estimated Power Input box (Integer only)

Measured power box

Measure button
Figure 65 [Procedure] 1. Connect the handset and GSM tester (or Signal Generator) with RF cable. 2. Select a band and channel. [see 4.6.3.1)] 3. Send signals (*) from GSM tester. 4. Enter the value of input power from GSM tester in integers (from 10 to 110) considering RF cable loss. 5. Press the [Measure] button. 6. The result appears in Measured Power box.

The signal type from GSM tester must be either of two: 1. Continuous sine wave (without modulation) with the frequency as follows: (Frequency of the measured channel) + 67.708kHz. (Ex. channel: GSM 37ch the result: 942.467708 MHz) Power: 110 to 10 dBm 2. BCCH signal of the measured channel Power: 110 to 10 dBm Result When the handset is properly calibrated, the error between Estimated Power and Measured Power is less than 3dB.

4.6.4 Termination
Turn off the handset to ensure proper operations.

4.6.5 Trouble imfomation

When switching DCS and PCS, change the channel number as well. Or the band does not change properly. Example: If you change DCS 512 CH to PCS 512 CH, the band remains DCS.

2 33

GX30
4.7. Password reset
SPST resets the password (handset code is set to 0000). <Operation>

CONFIDENTIAL

1) Set the COM port on the SPST initial screen and click User Password Reset. Click Yes to reset. Click No to exit.

Figure 66 2) When completed, the following appears.

Figure 67

2 34

CONFIDENTIAL
4.8. Performance check and adjustment
With this function, SPST checks the performance of the handset and makes adjustments. <Operation>

GX30

1) Set the COM port on the SPST initial screen and click Performance check and adjustment. The following dialog box appears while processing.

Figure 68 2) When completed, the following is displayed. Click Back to main menu to exit.

Figure 69 The functions of each button are described below.

4.8.1 Main back light check

The main display back light turns on and the message appears on the PC.

Figure 70 Check the back light and press OK. If a failure occurs, see 10. Back Light does not turn on. in [3] Troubleshooting.

2 35

GX30
4.8.2 External back light check

CONFIDENTIAL

The external display back light turns on and the message appears on the PC. Check the back light and press OK. If a failure occurs, see 10. Back Light does not turn on. in [3] Troubleshooting.

4.8.3 Key back light check

The keypad back light turns on and the message appears on the PC. Check the back light and press OK.

4.8.4 LED check

The LED lights up in a specified color and the message appears on the PC. Check the LED and press OK. If a failure occurs, see 15. Flash light does not work. in [3] Troubleshooting.

4.8.5 Battery voltage check

Click to display the current battery voltage. If a failure occurs, see 1. Power is not turned on. in [3] Troubleshooting.

4.8.6 SD read/write test

Insert an SD card (otherwise a message prompts you to do so) and click the button to perform the SD card read/write test. If a failure occurs, see 17. SD (Memory) card is not recognized. in [3] Troubleshooting.

4.8.7 Vibrator test

Click to vibrate the handset. Click OK to exit. If a failure occurs, see 5. Vibrator does not work. in [3] Troubleshooting.

4.8.8 Melody test

A message describes test items. Click Yes to proceed and No to exit. The order of the test items: speaker hands free hands free (stereo) speaker (analog melody)
Trouble found by SPST (1) Speaker (2) Hands free Sound is heard in audio test. No sound is heard in audio test. (3) Hands free (stereo) Sound is heard in audio test. No sound is heard in audio test. (4) Speaker (analog melody) Troubleshooting (based on [3] Troubleshooting) See "7. Speaker does not work." Parts between IC105 pin 10 and IC103 pin 93 are defective, or IC103 is defective. See "Hands free kit (monaural headset)" in the section "3. No voice is heard from the earpiece." Parts between IC105 pin 10 and IC103 pin 93; IC105 pin 11 and IC103 pin 94 are defective. Otherwise IC103 is defective. See "Hands free kit (stereo headset) - Option" in the section "3. No voice is heard from the earpiece." See "9. Video/Voice Recorder playback is impossible." Otherwise parts between IC105 pin 10 and IC103 pin 93 are defective, or IC103 is defective.

2 36

CONFIDENTIAL
4.8.9 Audio test
The following appears.

GX30

Figure 71 Select a test item from Audio device. Check the output sound from the receiver by speaking to the microphone, etc. Click Back to test menu to return to the previous screen.
Trouble found by SPST (1) Handset microphone Handset receiver (2) Handset microphone Hands free receiver (1) & (2): No voice is heard. (1): Voice is heard. (2): No voice is heard. (1): No voice is heard. (2): Voice is heard. (3) & (4): No voice is heard. (3): Voice is heard. (4): No voice is heard. (3): No voice is heard. (4): Voice is heard. Troubleshooting (based on [3] Troubleshooting) See "Phone" in the section "2. Voice transmission/recording is impossible." See "Hands free kit (monaural headset)" in the section "3. No voice is heard from the earpiece" or "Hands free kit (stereo headset) - Option" in the section "3. No voice is heard from the earpiece." See "Phone" in the section "3. No voice is heard from the earpiece."

(1) & (2): No voice is heard.

(3) Hands free microphone Hands free receiver

(4) Hands free microphone Handset receiver

See "Hands free kit (headset)" in the section "2. Voice transmission/recording is impossible."

4.8.10 Camera check

The following appears.

Figure 72 Select a Camera mode from the pull-down menu. Click Shutter to check that the camera operates properly. Click Back to performance check menu to return to the previous screen. If a failure occurs, see 14. Pictures cannot be taken. in [3] Troubleshooting.

4.8.11 Memory check

Click S-RAM and PSRAM to see each test result. For Check Sum, the calculation appears after the SPST communicating dialog box.

2 37

GX30
4.8.12 LCD test

CONFIDENTIAL

Check that the specified color appears on the main display. If a failure occurs, see 12. The display does not appear on Main Display. and 13. The display does not appear on External Display (in 65K color mode). in [3] Troubleshooting.

4.8.13 Temperature adjustment

The following appears. Setting temp. indicates the current temperature. The relative temperature is displayed in the text box below. (Only the relative temperature is adjustable.) If displayed Setting temp. value differs from the current temperature, click Save. or to set a correction value in the range of 99 to +99 and click

Correction value = (Setting temp.) --- (current temp.) + (displayed correction value)
Figure 73

4.8.14 Main display flicker adjustment

The following is displayed.

Figure 74 Check a main display visually within a distance of 20 cm from a fluorescent light, and adjust the value to minimize flicker on the display with the and buttons. Click Save and confirm that the main display does not flicker.

(Fine adjustment for DC voltage between display electrodes)

Enlarged view (A black line appears after each gradation line.)

8-level gradation pattern with alternate black and gradation lines (black and white)
Figure 75

2 38

CONFIDENTIAL
4.8.15 External display contrast adjustment
Click the External display contrast adjustment button. The following screen appears.

GX30

DEN: 075

8-level gradation pattern (black & white pattern)

Figure 76 Comparing with an adjusted handset, click the pattern on the external display. or to adjust the value so that the same gradation pattern is displayed. Click Save and confirm

4.8.16 White defect correction

* White defect correction: Defective pixels in a camera light sensor appear as bright points in the display even when light is blocked completely (display is all black). Perform white defect correction to eliminate errors in these pixels. 1. Protect the handset camera from light completely with a black cover. 2. Click the White defect correction button. The following screen appears.

Figure 77 Click the Yes button and leave it for about 20 seconds. When completed, the following message appears.

Figure 78

2 39

GX30

CONFIDENTIAL

When an error occurs, the corresponding message appears. Solve the problem according to Solution. Error 1 Error message: There are too many white cracks. Cause: The light is not sufficiently blocked. Solution: Block the light completely and perform white defect correction again. Error 2 Error message: There are many white cracks. Cause: The light is not sufficiently blocked. Solution: Block the light completely and perform white defect correction again. Error 3 Error message: There are too many white cracks cannot be rectified. Cause: There is a hardware error. Solution: Replace the camera unit.

4.8.17 Black defect correction

*Black defect correction: Defective pixels in a camera light sensor appear as black points in the display even when a captured image is completely white (display is all white). Perform black defect correction to eliminate errors in these pixels.

1) Requirements
Desk top type of fluorescent lamp Black defect correction sheet

Figure 79 Illuminance meter

2) Procedure
1. Cover the camera section with the black defect correction sheet as shown in Figure 80.

Attach the sheet to the handset firmly with clear scotch tape.

Figure 80

2 40

CONFIDENTIAL
2. Check the distance from the fluorescent lamp by using an illuminance meter. In the proper position for black defect correction, illuminance is between 8,000 and 10,000 lux.

GX30

Figure 81 3. Hold the handset in the proper position.

Figure 82 4. Click the Black defect correction button. The following message is displayed.

Figure 83 5. Click the Yes button. Communication starts.

Figure 84

2 41

GX30
6. The result is displayed within a minute as follows.

CONFIDENTIAL

Figure 85 When an error occurs, the corresponding message appears. Solve the problem according to Solution. Error 1 Error message: There are too many black cracks. Cause: The light is too weak or strong. Solution: At the proper distance from the light source (8,000 - 10,000 lux), perform black defect correction again. Error 2 Error message: There are many black cracks. Cause: The light is too weak or strong. Solution: At the proper distance from the light source (8,000 - 10,000 lux), perform black defect correction again. Error 3 Error message: There are too many black cracks cannot be rectified. Cause: There is a hardware error. Solution: Replace the camera unit.

4.9. ****mode release

When the handset does not turn on and enter the normal mode, use this function to change ****mode to the normal mode. <Operation> 1) Select the COM port on the SPST initial screen and click ****mode release. The following dialog box appears.

Figure 86 2) If SPST cannot communicate with the handset, the following message is displayed. Make sure the handset is turned on and click Retry. To exit, click Cancel.

Figure 87 3) When complete, the following message appears.

Figure 88

2 42

CONFIDENTIAL
5. Other tests
SPST does not provide tests of Bluetooth/USB communication. Check them according to the following instructions.

GX30

5.1. Bluetooth
Connect GX30 to the network and check that a conversation (talking and listening) is possible using a Bluetooth headset. Recommended Bluetooth headset: JABRA BT200 PLANTRONICS M1000 PLANTRONICS M3000

5.2. USB
Connect GX30 and a PC with a USB cable. Check that GX30 is recognized as a device. If the USB driver for GX30 (SHARP GSM GPRS USB Driver) is not installed on the PC, Found New Hardware window appears and Found New Hardware Wizard starts (the handset is recognized).

2 43

GX30

CONFIDENTIAL

[2] Test points

MAIN PWB-A (FRONT SIDE)
TP705

TP720

TP710

TP711

TP737

TP734

TP721

TP723

TP724

TP714

TP722

TP712

TP731

TP735

TP716

TP701 TP702 TP736 TP728

TP730 TP727 TP738

TP715

TP732

TP733

TP706

TP707

Figure 89 TEST POINT TP No. TP701 TP702 TP705 TP706 TP707 TP709 TP710 TP711 TP712 TP713 TP714 TP715 TP716 TP717 TP720 TP721 Signal name SP1 SP2 VCCD (2.5V) Terminal for APPLICATION POWER adhesion check 1 Terminal for APPLICATION POWER adhesion check 2 VDD6 (3.1V) Backlight (LED+) Backlight (LED) CAMCLK 13MHzCLK VLCD (1.8V) Terminal for LCDC adhesion check 1 Terminal for LCDC adhesion check 2 VOUT (External Display) VDD2 RECIVER_OUTN TP No. TP722 TP723 TP724 TP727 TP728 TP729 TP730 TP731 TP732 TP733 TP734 TP735 TP736 TP737 TP738 Signal name RECIVER_OUTP Terminal for LCDC adhesion check 3 Terminal for LCDC adhesion check 4 LIGHT1 LEDCTL LEDR LEDG LEDB Power supply for camera (+15V) Power supply for camera (8V) RECIVER_OUTN RECIVER_OUTP AVDD (3.1V) VPLUS2 Connector connection check terminal

2 44

TP717

TP713

TP729

TP709

CONFIDENTIAL
MAIN PWB-A (REAR SIDE)

GX30

TP708

TP718

TP719

Figure 90 TEST POINT TP No. TP703 Signal name SP1 TP No. TP704 Signal name SP2

2 45

TP704

TP703

GX30
KEY PWB-B (FRONT SIDE)

CONFIDENTIAL

TP144

TP147

TP154

TP153

TP127

TP183

TP123

TP160

TP161

TP104

TP158

TP173

TP109

TP126

TP113

TP167

TP536 TP107 TP535 TP524 TP101 TP152 TP151 TP150 TP149 TP125 TP172 TP537 TP103 TP515 TP118 TP108 TP120 TP169 TP119 TP180 TP166 TP525 TP523 TP102 TP526

TP502

TP182

TP503

TP168

TP155

TP514

TP121

TP163

TP162

TP528

TP178

TP157

TP184

TP135

TP181

TP527

TP506

TP170

TP801

TP802

TP177

TP174

TP164

Figure 91 TEST POINT TP No. TP103 TP104 TP105 TP107 TP108 TP109 TP113 TP118 TP119 TP120 TP121 TP123 TP124 TP126 TP127 TP144 TP147 TP153 TP157 TP158 TP160 TP161 TP162 TP163 TP164 TP165 TP166 TP167 TP168 TP169 TP170 Signal name USC [0] USC [1] USC [2] USC [4] USC [5] USC [6] VVIB USC [3] MIC AUDIO_IN JACK_L RESET PWRON SP1 SP2 Terminal for STACK MEMORY adhesion check 1 Terminal for STACK MEMORY adhesion check 2 VPP Flash Analog Power Supply IC INT VINT (3V) HEDSET_DET STEREO_SW REMOTE_SW JACK_R VABB VT (2.75V) VUSB VRTC (1.8V) VBACK (3V) VSIM (2.85V) VMEM (2.8V) TP No. TP171 TP172 TP173 TP174 TP176 TP177 TP178 TP179 TP180 TP181 TP182 TP183 TP184 TP502 TP503 TP506 TP514 TP515 TP521 TP523 TP524 TP525 TP526 TP527 TP528 TP535 TP536 TP537 TP801 TP802 Signal name VCORE (1.8V) VAPP VINT (3V) LIGHT3 (KEYLED) VMIC AUXADC1, 2 TEMP AUXADC1, 2 CHGIN_A (5.2V) Flexible PWB insert check terminal 1 Flexible PWB insert check terminal 2 Flexible PWB insert check terminal 3 Flexible PWB insert check terminal 4 VBAT VBAT BATT_SENSE BT_VCC (3.0V) VBUS_IN POWONKEY USB D+ USB D RTS CTS DGND DGND Reserved ManufactUre Specific CHGIN VTCXO (2.9V) VRF (2.9V)

2 46

TP179

TP165

TP176

TP521

TP124

TP171

TP105

CONFIDENTIAL
KEY PWB-B (REAR SIDE)

GX30

TP533 TP530 TP529 TP516 TP518

TP132 TP148 TP138

TP531

TP532

TP505 TP534

TP130

TP519

TP117 TP110 TP106 TP134 TP133 TP139 TP131

TP517

TP501

TP520

TP522

TP504

TP145 TP143 TP137

TP128 TP508 TP114 TP115 TP116 TP136 TP112 TP142 TP146 TP141 TP111 TP140 TP156 TP122

Figure 92 TEST POINT TP No. TP111 TP112 TP501 TP504 Signal name VVIB DGND BATT DGND TP No. TP505 TP520 TP522 TP534 Signal name DGND BATT POWONKEY BATT_SENSE

2 47

GX30

CONFIDENTIAL
Power is not turned on. Voice transmission/recording is impossible. No voice is heard from the earpiece. Battery does not charge. Vibrator does not work. Clock Settings are reset. Speaker does not work. MP3 cannot be played. Video/Voice Recorder playback is impossible. Back Light does not turn on. Out of range and incoming/outgoing calls are impossible. The display does not appear on Main Display. The display does not appear on External Display (in 65K color mode). Pictures cannot be taken. Flash light does not work. SIM card is not recognized. SD (Memory) card is not recognized. IrDA (Infrared) communication is not possible. Bluetooth communication is impossible. USB connection is impossible. See page 2-48 See page 2-50 See page 2-52 See page 2-54 See page 2-54 See page 2-55 See page 2-55 See page 2-56 See page 2-57 See page 2-58 See page 2-59 See page 2-60 See page 2-61 See page 2-62 See page 2-63 See page 2-64 See page 2-65 See page 2-66 See page 2-67 See page 2-68

[3] Troubleshooting
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.

1. Power is not turned on.

Connect a battery of 4.0 V or more.

Execute File System Initialization of Downloader in SPST without loading a file.

Does File System Initialize start properly?

YES

Is the user area (file system) initialized by Flash Loader?

NO

NO

YES

5-level stack memory (IC101) and IC106 are defective. Does normal mode start?
NO YES

5-level stack memory (IC101) data is corrupted. Is it possible to rewrite the firmware?
YES NO

5-level stack memory (IC101) and IC106 are defective. Does normal mode start after restart?
NO YES

5-level stack memory (IC101) and IC106 are defective.

Program code of 5-level stack memory (IC101) is garbled.

A
(To page 2-49)

2 48

CONFIDENTIAL
(From page 2-48)

GX30

Is 3.6 V or more applied to BATT terminal (TP520)?

YES

NO

Battery terminals are defective, connector terminal is dirty, or soldering is improper.

Is the voltage 1.2 V or lower on SENSE terminal (TP506)?

YES

NO

The battery is defective or set improperly.

Is there conduction through fuse (FS501)?

YES

NO

Fuse (FS501) is blown.

Is 5-level stack memory (IC101) installed properly?

YES

NO

5-level stack memory (IC106) is installed improperly.

Is 2.8 V and 1.8 V applied to VMEM (TP170) and VCORE (TP171) respectively?
YES

NO

IC103 is defective.

Is 3.0 V applied to VINT (TP173)?

YES

NO

IC111 is defective.

Is the waveform of signals from R169 connected to X101 (32 kHz) correct? Are R167, R169, R174A, C176, X101, and IC106 good in appearance and mounted properly?
YES

NO

X101 (32 kHz oscillator), R167, R169, C174, and C176 are defective or mounted improperly. Or oscillating circuit of IC106 is defective.

Is the rectangular wave of 13 MHz properly sent to TP713?

NO

YES

IC106, R179, and R110A are defective or mounted improperly. CN701 and CN102 are connected improperly.

Is the triangular wave of 13 MHz sent from C833?

NO

YES

IC801 is defective.

Is 2.9 V supplied from VTCXO (TP801)?

YES

NO

Power Supply (IC804) is defective.

IC801 and peripheral circuits are defective.

2 49

GX30

CONFIDENTIAL

2. Voice transmission/recording is impossible.

Phone (Handset) Replace the microphone. Is the problem solved?
NO

YES

The built-in microphone is defective or in a poor contact with the PWB. L101, L102, and C101 are defective.
YES

Is 1.2 - 2.1 V applied to both ends of C101?

YES

NO

Is 1.2 - 2.1 V applied to TP119?

NO

Is 2.4 - 2.5 V applied to TP176?

NO YES

R125 is defective. Is 2.4 - 2.5 V applied to IC103 pin 76?

NO YES

R115 and C108 are defective. IC103 is defective.

NO

Is approx. 1.7 V applied to IC103 pin 80?

YES

Is approx. 1.7 V applied to IC103 pin 96?

NO YES

R263 and R130 are defective. Is 2.7 or more voltage applied to R192 (IC106 pin 89 side)?
YES NO

IC103 is defective.

R192 is defective. (Headset mode is set.)

Replace C126 or C133. Is the problem solved?

NO

YES

C126 or C133 is defective.

IC103 and IC106 are defective.

2 50

CONFIDENTIAL
Hands free kit (Headset) (The following procedure applies to both monaural and stereo headsets.) Replace the hands free kit. YES Is the signal sent?
NO

GX30

Hands free kit is defective.

R104A, R112, and V101 are defective.

YES

Is 0.7 - 1.8 V applied to JK101 pin 2?

YES

NO

Is 0.7 - 1.8 V applied to TP120?

NO

Is 2.4 - 2.5 V applied to TP176?

NO YES

R122 is defective. Is 2.4 - 2.5 V applied to IC103 pin 76?

NO YES

R115 and C108 are defective. IC103 is defective.

NO

Is approx. 1.7 V applied to IC103 pin 79?

YES

Is approx. 1.7 V applied to IC103 pin 95?

NO YES

R262 and R129 are defective. Is the voltage 0 V on R192 (IC106 pin 89 side)?
YES NO

IC103 is defective.

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit (Handset mode is set.)

Replace C127 or C134. Is the problem solved?

NO

YES

C127 or C134 is defective.

Replace JK101. Is the problem solved?

NO

YES

JK101 is defective, or the jack plug pin 2 is in a poor contact with hands free kit.

IC103 and IC106 are defective.

2 51

GX30
3. No voice is heard from the earpiece.
Phone (Handset) Is the signal sent to the contact terminal of the earpiece?
NO

CONFIDENTIAL

YES

The built-in earpiece is defective, or in a poor contact with TP734 or TP735.

Is the signal sent to CN103 pins 17 and 18?

NO

YES

The camera relay FPC, CN103, or CN701 is defective. Or the camera is in a poor contact with CN103 and CN701.

Is the signal sent to vsGNDs at both ends of C132?

NO

YES

L107, L108, C115, and C120 are defective.

Is 2.7 or more voltage applied to R192 (IC106 pin 89 side)?

YES

NO

R192 is defective. (Headset mode is set.)

Is approx. 1.2 V applied to IC103 pins 59 and 63?

YES

NO

IC103 is defective.

IC103 or IC106 is defective. Hands free kit (monaural headset) Replace the hands free kit. Is the signal sent?
NO

YES

Hands free kit is defective.

Is the signal sent to JK101 pin 3?

NO

YES

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit.

Is the signal sent to TP121?

NO

YES

L103 is defective.

Is the signal sent to the positive pole of C107?

NO

YES

C107, C103, and V106 are defective.

Is the signal sent to IC103 pin 60?

NO

YES

R124 is defective.

Is the voltage 0 V on R192 (IC106 pin 89 side)?

YES

NO

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit. (Handset mode is set.)

Is approx. 1.2 V applied to IC103 pin 60?

YES

NO

IC103 is defective.

IC103 or IC106 is defective.

2 52

CONFIDENTIAL
Hands free kit (stereo headset) - Option

GX30

The headset cannot be used. (It works as a monaural headset.)

NO

Is the stereo headset the one specified by Sharp?

YES

NO

Is the plug a 6 pole type with a ring?

YES

Is R-ch only the channel that does not send signals?

NO

YES

Replace the hands free kit. Is the signal sent?

NO

YES

Hands free kit is defective.

Is the signal sent to JK101 pin 3?

NO

YES

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit.

Is the signal sent to TP121?

NO

YES

L103 is defective.

Is the signal sent to the positive pole of C107?

NO

YES

C107, C103, and V106 are defective.

Is the signal sent to IC103 pin 60?

NO

YES

R124 is defective.

Is the voltage 0 V on R192 (IC106 pin 89 side)?

YES

NO

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit. (Handset mode is set.)

Is approx. 1.2 V applied to IC103 pin 60?

YES

NO

IC103 is defective.

IC103 or IC106 is defective.

Is the signal sent to JK101 pin 1?

NO

YES

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit.

Is the signal sent to TP163?

NO

YES

L105 is defective.

Is the signal sent to the positive pole of C110?

NO

YES

C110, C105, and V109 are defective.

Is the signal sent to IC103 pin 64?

NO

YES

R126 is defective.

Is the voltage 0.1 V or lower on R191 (IC106 pin 100 side)?

YES

NO

Jack JK101 is defective, or the jack plug is in a poor contact with hands free kit. (Monaural mode is set.)

Is approx. 1.2 V applied to IC103 pin 64?

YES

NO

IC103 is defective.

IC103 or IC106 is defective.

2 53

GX30
4. Battery does not charge.
Set a battery of 3.8 - 3.9 V and connect the charger.
YES

CONFIDENTIAL

CN701 and CN103 are connected improperly, and IC103 is defective.

NO NO

Is the mobile light turned on red?

YES

Does the waveform periodically change between H and L at R701?

YES

Set a battery of 4.0 - 4.2 V. Click the Performance check adjustment button on SPST.

LED702 of the mobile light is defective. * For settings and connections for SPST, refer to the ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE (see page 2-1). TH701, TH101, and IC103 are defective. CN701 and CN103 NO are connected improperly.

Click the Temperature adjustment button. Is the value of temp normal? (Measurement tolerance: 5 deg.)
YES

Click the Battery voltage check button. Is the voltage 4.0 4.2 V?
YES

NO

IC103 is defective.

Set a battery of 3.3 - 4.2 V and start in normal mode.

Connect the charger to the external connector. Is the voltage applied to TP537 higher than that of battery?
YES

NO

R535, R536, Q108, IC115, and IC103 are defective.

When the charger is inserted to the external connector, is IC115 pin 1 at L?

YES

NO

IC115 is defective.

Connect the charger to the external connector. After approx. 15 seconds, do the voltages on TP180 and TP520 increase by more than 0.05 V?
YES

NO

R535, R536, Q108, IC115, IC103, D103, and D105 are defective.

The battery is defective, or the battery cycle is shortened.

5. Vibrator does not work.

Are vibrator terminals in contact with the land? NO Are terminals and the land clean? Hereafter check with Vibrator working.
YES

Vibrator is deformed and defective. (When vibrator terminals and the land are dirty, clean or replace them.)

Is rectangular wave of 3 V sent to between Vibrator terminals in sync with the vibration pattern?
NO

YES

Vibrator is defective.

Is VBAT voltage applied to IC109 pin 5?

YES

NO

IC109 is soldered improperly.

Is signal synchronized with the vibration pattern sent to IC109 pin 1?

NO

YES

IC109 is defective.

Is signal synchronized with the vibration pattern sent from IC105 pin 19?
NO

YES

IC105 is soldered improperly.

R158, C167 and C168 are defective.

NO

Is approx. 3 V applied to IC105 pin 7?

YES

NO

R158, C167 and C168 good in appearance and mounted properly?

YES

IC105 is defective, or the control signal line to IC106 is defective.

2 54

CONFIDENTIAL
6. Clock Settings are reset.
The holder is installed improperly.
NO

GX30

Is 2.5 V or more applied to TP168 with a battery in the handset?

YES

NO

Is back-up battery holder properly installed to SD/SIM FPC?

YES

The remaining power of back-up battery is insufficient. Back-up battery is defective. Back-up battery holder is defective. SD/SIM FPC is broken, or CN104 is defective. R254 is defective. Is 1.5 V or more applied to TP167 without a battery in the handset?
YES NO

IC103 is defective.

X101, R169, R174A, and C176 are defective.

7. Speaker does not work.

* When ring tones sound, but keypad tones do not, Keypad Tones is set to Off. * When Ringer Volume is set to Silent: Voice Recorder playback sound is not produced. Playback sound of Video and MP3 can be heard by increasing the volume during playback. Are speaker terminals in contact with the land?
YES NO

Speaker is defective.

Is the impedance between speaker terminals approx. 8 ohms?

YES

NO

Speaker is defective.

Is the signal sent to TP701, TP702, or speaker contact pad?

NO

YES

Speaker is defective.

Is the signal sent to CN103 pins 3 and 4?

NO

YES

The camera relay FPC, CN103, or CN701 is defective. Or the camera is in a poor contact with CN103 and CN701.

Is VBAT voltage applied to IC105 pin 15?

YES

NO

R139 is defective.

Is approx. 3 V applied to IC105 pins 7 and 32?

YES

NO

R158 is defective.

Is the signal sent to IC105 pin 12?

NO

YES

R145 and R146 are defective, or IC105 is defective.

IC105 or the control line to IC106 is defective.

2 55

GX30
8. MP3 cannot be played.
Speaker

CONFIDENTIAL

Not defective.
YES

Is Ringer Volume set to Silent?

NO

YES

Cancel Silent. Is sound produced?

NO

Go to the section Video/Voice Recorder playback is impossible. (see page 2-57)

YES

Is output of the video and voice recorder normal?

YES

NO

Are keypad tones and ring tones normal?

NO

Go to the section Speaker does not work. (see page 2-55) Insert an SD card with MP3 files recorded on a normal unit. Do they play?
NO YES

Not defective. Or SD card is defective.

Is the SD card recognized?

YES

NO

Go to the section SD (Memory) card is not recognized. (see page 2-65)

Is the signal sent to IC103 pin 60?

NO

YES

Parts between IC103 pin 60 and IC105 pins 14 & 13 are defective or soldered improperly.

IC103 is defective.

Hands free kit (headset) (The following procedure applies to both monaural and stereo headsets.) Is sound normally produced from Speaker?
YES NO

Go to the section regarding Speaker.

Replace the hands free kit. Is sound produced?

NO

YES

Hands free kit is defective.

Go to Hands free kit (monaural headset) in the section No voice is heard from the earpiece. (see page 2-52)

2 56

CONFIDENTIAL
9. Video/Voice Recorder playback is impossible.
Speaker Are keypad tones and ring tones normal?
YES NO

GX30

Go to the section Speaker does not work. (see page 2-55)

In Playback window, does playback start normally and the capacity bar change?
YES

NO

IC101 or IC106 is defective.

Not defective.
YES YES

Is Ringer Volume set to Silent?

NO

Cancel Silent. Is sound produced?

NO

Is the signal sent to IC103 pin 60?

NO

YES

Parts between IC103 pin 60 and IC105 pins 14 & 13 are defective or soldered improperly.

IC103 is defective.

Hands free kit (headset) * If R-ch is the only channel of stereo headset that does not send signals, see Hands free kit (stereo headset) - Option in the section No voice is heard from the earpiece. (see page 2-53) Replace the hands free kit. Hands free kit is defective. YES Is the signal sent?
NO

In Playback window, does playback start normally and the capacity bar change?
YES

NO

IC101 or IC106 is defective.

Not defective.
YES YES

Is Ringer Volume set to Silent?

NO

Cancel Silent. Is sound produced?

NO

Go to Hands free kit (monaural headset) in the section No voice is heard from the earpiece. (see page 2-52)

2 57

GX30
10. Back Light does not turn on.

CONFIDENTIAL
FS701 is mounted improperly, or the fuse is brown.
NO

Is VBAT voltage applied to C701?

NO

Is fuse (FS701) in good appearance, mounted properly, and is there conduction?

YES

YES

C701, C703, and L701 are defective. External display only. Which back light does not turn on, Main or External? Main Display only or both.

Is back light setting for External Display set to On?

NO

Go to the setting as follows and set it to On: Settings Phone settings Main display Back light

YES NO

Does it turn on?

YES

Not defective. Is CN705 in good appearance and mounted properly?

YES NO

CN705 is defective. Back light FPC or CN705 is defective.

NO

Is the contact point of back light FPC clean? Is back light FPC properly inserted to CN705?
YES

NO

Clean back light FPC and insert it again. Does it turn on?
YES

Not defective. Is 13 - 24 V applied between TP710 and TP711?

NO YES

Back light FPC is defective.

Are C790, C791, C702, C707, C713, R718, and D702 in good appearance and mounted properly?
YES

NO

C790, C791, C702, C707, C713, R718, and D702 are defective.

IC707, and R707 are defective.

Is back light setting for Sub Display set to On?

NO

Go to the setting as follows and set it to On: Settings Phone settings External display Back light

YES NO

Does it turn on?

YES

Not defective. Is 7 V applied between LED703 anode (A) terminal and LED704 cathode (K) terminal?
YES NO

IC707 is defective or mounted improperly.

LED703 and LED704 are defective.

2 58

CONFIDENTIAL
11. Out of range and incoming/outgoing calls are impossible.
[Checkpoints in RF Test Tool] Is transmission possible using RF Test Tool?
YES

GX30

[Sender]

NO NO

Is voltage (applox. 2.9 V) supplied to pin 6 of IC804?

YES

IC804 is defective.

Is IQ signal supplied to pins 23, 24, 25, and 26 of IC801?

YES

NO

IC103, IC106, or PWB is defective.

Is frequency signal sent? GSM850/GSM900 bands ......... IC801 pin 17 DCS1800/PCS1900 bands ...... IC801 pin 19
YES

NO

IC801 is defective.

Is frequency signal supplied? GSM850/GSM900 bands ........ FL803 pin 15 DCS1800/PCS1900 bands ..... FL803 pin 13
YES

NO

IC802 is defective.

Is frequency signal supplied to pin 1 of FL905?

YES

NO

FL803 is defective.

Is frequency signal supplied to pin 1 of J801?

YES

NO

FL905 is defective.

J801 is defective. [Receiver] 70 dBm input.

Is frequency signal supplied? GSM850/GSM900 bands ............. IC801 pins 9, 10 DCS1800 band ............................ IC801 pins 6, 7 PCS1900 band ............................ IC801 pins 3, 4
NO

IC801 is defective.
YES

Is frequency signal supplied? GSM850 band ..............................FL904 pins 9, 10 GSM900 band...............................FL904 pins 6, 7 DCS1800/PCS1900 bands ......... Go to the next step.
NO

FL904 is defective.
YES

Is frequency signal supplied? GSM850 band ................................ FL901 pin 1 GSM900 band ................................ FL902 pin 9 DCS1800 band ............................... FL902 pin 6 PCS1900 band ............................... FL903 pin 1
NO

FL901, FL902, or FL903 is defective.

YES

Is frequency signal supplied to pin 9 of FL803?

NO

YES

FL803 is defective.

FL905 or J801 is defective.

2 59

GX30

CONFIDENTIAL

12. The display does not appear on Main Display.

Is Main Display unit fully inserted to CN704?
YES

NO

Improperly inserted to the connector.

Clean the contact point of CN704 and insert the unit again. Does the display appear?
NO

YES

The contact point of the connector is dirty.

Replace Main Display. Does the display appear?

NO

YES

Main Display unit is defective.

Is 3.6 or more voltage applied to VBAT terminal (FS701) and VBAT_L terminal (FS702)?
YES

NO

Go to the section Power is not turned on. (see page 2-48)

Is 2.8 0.1 V applied to TP170?

YES

NO

Go to the section Power is not turned on. (see page 2-48)

Is 3.0 0.1 V or more applied to TP173?

YES

NO

Go to the section Power is not turned on. (see page 2-48) Regulator IC703 or R716 is defective.
NO

Is 1.8 0.1 V or more applied to TP714?

NO

Is 3.0 0.1 V applied to IC703 pin 1? Are R743 and C728 good in appearance and mounted properly?
YES

YES YES

Are CN701 and CN103 good in appearance and mounted properly?

NO

CN703 and CN103 are defective or mounted improperly. And FPC is defective. Is 13 MHz applied to clock TP713?
YES NO

Go to the section Power is not turned on. (see page 2-48)

Is 3.0 0.1 V supplied from LCD_RST (L749)? Are L749, C736, C751, CN701, and CN703 good in appearance and mounted properly?
YES

NO

L749, C736, C751, CN701, and CN703 are defective or mounted improperly.

Is 3.0 V 0.1 V applied to CN704 pins 34, 37, and 38? Are R737, R738, C774, and C775 good in appearance and mounted properly?
YES

NO

CN704, R737, R738, C774, and C775 are defective or mounted improperly.

Is 3.0 0.1 V applied to the LCD reset (CN704 pin 33 and C766)? Is C766 good in appearance and mounted properly?
YES

NO

Display controller IC (IC704) and C761 are defective or mounted improperly.

Is the signal of approx. 62 Hz present on C760? Are C758, C759, C760, and C761 good in appearance and mounted properly?
YES

NO

Display controller IC (IC704), C758, C759, C760, and C761 are defective or mounted improperly.

Is the following voltage applied to the terminal? TP720: approx. 10 V Are C771, C772, C773, C776, C777, C779, C780, C781, C782, and C783 good in appearance and mounted properly?
YES

NO

Main Display unit, CN704, C771, C772, C773, C776, C777, C779, C780, C781, C782, and C783 are defective.

Main Display unit is defective, or connector CN704 is mounted improperly.

2 60

CONFIDENTIAL
13. The display does not appear on External Display (in 65K color mode).

GX30

Does the display appear on Main Display?

YES

NO

Go to the section Power is not turned on. (see page 2-48)

Is External Display On/Off setting set to On?

NO

Go to the setting as follows and set it to On: Settings Phone settings External display Display On/Off

YES

Is External Display unit fully inserted to CN703?

YES

NO

Improperly inserted to the connector.

Clean the contact point of the connector CN703 and insert the unit again. Does the display appear?
NO

YES

The contact point of the connector is dirty.

Is 3 0.1 V applied to CN703 pin 9? Is R723 good in appearance and mounted properly?
YES

NO

R723 is defective or mounted improperly.

Are CN701 and CN103 good in appearance and mounted properly?

YES

NO

CN703 and CN103 are defective or mounted improperly. And FPC is defective.

Is 3.0 0.1 V supplied from LCD_RST (CN703 pin 27 and C751)?

YES

NO

IC707, C736, C751, and L749 are defective or mounted improperly.

Is R222 good in appearance and mounted properly?

YES

NO

R222 is defective or mounted improperly.

Are C755, C756, and C758 good in appearance and mounted properly? Is electric potential normal at both ends of C755, C756, and C757? Are rectangular waves sent? C755: rectangular wave of approx. 3 V C756: rectangular wave of approx. 6 V C757: rectangular wave of approx. 9 V
YES

C755, C756, C757, and CN703 are defective, or External Display unit is defective.
NO

Is approx. 11.8 V applied to CN703 pin 7 (TP717)? Are the following voltages applied to V0 - V4? V0 (C744): approx. 8.56 V V1 (C745): approx. 7.33 V V2 (C747): approx. 6.11 V V3 (C748): approx. 2.42 V V4 (C750): approx. 1.20 V
YES

NO

C744, C745, C747, C748, C750, CN703, and IC704 are defective. The control signal line to IC704 or External Display unit is defective.

* After a period of time the back light turns off, the voltage on TP717 decreases to approx. 9 V.

External Display unit is defective.

2 61

GX30
14. Pictures cannot be taken.

CONFIDENTIAL

Replace camera relay FPC. Does camera work?

NO

YES

Camera relay FPC is defective.

Is 2.5 V applied to TP705?

YES

NO

Regulator IC701 or R705 is defective.

Is 2.5 V applied to pin 23 of camera unit?

YES

NO

CN701 is defective. Camera relay FPC is broken.

Is 3.0 V applied to TP173?

YES

NO

Regulator IC111 or R239 is defective.

Is 3.0 V applied to pins 33 & 34 of camera unit?

YES

NO

R101 and CN102 are defective. Camera relay FPC is broken.

Is 3.0 V applied to TP736?

YES

NO

Regulator IC708 or R758 is defective.

Is 3.0 V applied to pin 32 of camera unit?

NO

CN701 is defective. Camera relay FPC is broken. IC704 is defective.

NO

YES

Is 3.1 V applied to TP709?

YES

NO

Is 3.0 V applied to IC702 pin 1?

YES

Regulator IC702 is defective. Is 3.1 V applied to pin 35 of camera unit?

NO

CN701 is defective. Camera relay FPC is broken. IC707 or peripheral circuits are defective.
YES

YES

Is 15 V applied to TP732?
YES

NO

Does the LED of the flash work properly?

NO

IC707 or peripheral circuits are defective. Also IC704 or the control line is defective. CN701 is defective. Camera relay FPC is broken.
YES

Is 15 V applied to pin 42 of camera unit?

NO

Are C741 and C724 good in appearance and mounted properly?

NO

YES

C741 and C724 are defective. IC707 or peripheral circuits are defective.
YES

Is -8 V applied to TP733?
YES

NO

Does the LED of the flash work properly?

NO

IC707 or peripheral circuits are defective. Also IC704 or the control line is defective.

D
(To page 2-63)

2 62

CONFIDENTIAL
(From page 2-62)

GX30

CN701 is defective. Camera relay FPC is broken.

YES

Is -8 V applied to pin 36 of camera unit?

NO

Are C740 and C726 good in appearance and mounted properly?

NO

YES

C740 and C726 are defective. Is signal properly sent from CAMCK (TP712)?
YES NO

IC704 is defective.

IC106, parts of the control signal line, CN102, and CN702 are defective.

15. Flash light does not work.

Click the Performance check adjustment button on SPST to perform LED check. See in which color of RGB the flash does not work. * For operations and settings for SPST, refer to ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE (see page 2-1). The control line between IC707 and IC704 is defective. Or IC707 and IC704 are defective. Red only Which color? Blue, green, or all three colors
YES

Replace with a battery of 3.8 - 3.9 V, and connect the charger to the external connector. Does the flash light?
NO

CN103 pin 29 and IC707 pin 10 are connected improperly, or IC707 is defective.

Is VBAT voltage applied to C714?

NO

YES

Q702, L702, D703, and R704 are mounted improperly, or the parts are defective.

Is fuse (FS701) in good appearance, mounted properly, and is there conduction?

YES

NO

FS701 is mounted improperly, or the fuse is blown.

Is 3 V applied to TP728?
YES

NO

IC113 and peripheral parts are defective or mounted improperly.

Does the camera work properly?

NO

YES

IC707 is defective.

The control line between IC707 and IC704 is defective. Or IC707 and IC704 are defective.

2 63

GX30
16. SIM card is not recognized.
Replace the SIM card. Is it recognized?
NO

CONFIDENTIAL

YES

SIM card is defective or not the one specified.

Hereafter, check the signal waveform of each SIM when the power is turned on without a SIM card inserted. (SIM signal waveform appears for approx. 70 ms after the power is turned on.) The contact point of the SIM card connector is deformed or dirty.

Is 2.85 V supplied from pins 1, 2, and 6 of the SIM card? And is periodic pulse wave (3.25 MHz) sent from pin 3 of the SIM card?
NO

YES

Replace C210 or C159.

NO

Is 2.85 V supplied from CN104 pin 28?

NO

Are C210 and C159 good in appearance and mounted properly?

YES

YES

IC103 is defective. Replace R195 or C216.

NO

Is 2.85 V supplied from CN104 pin 30?

NO

Are R195 and C216 good in appearance and mounted properly?

YES

YES

IC106 is defective. Replace R164 or C217.

NO

Is periodic pulse wave sent from CN104 pin 31?

NO

Are R164 and C217 good in appearance and mounted properly?

YES

YES

IC106 is defective. Replace R163, R249, or C218.

NO

Is 2.85 V supplied from CN104 pin 27?

YES

NO

Are R163, R249, and C218 good in appearance and mounted properly?
YES

CN104 or SD/SIM FPC is defective.

IC106 is defective.

2 64

CONFIDENTIAL
17. SD (Memory) card is not recognized.

GX30

Is the SD card checked for operation?

YES

NO

Use an SD card that has been checked.

Is the SD card recognized on PC, etc.?

YES

Is the card insertion detected?

YES

NO

Is SD/SIM FPC properly inserted to CN104?

YES NO

Reinsert SD/SIM FPC, and try again. Does the signal of SD_DET become L when the card is inserted?
YES NO

IC106 is defective.

SD card socket and CN104 are in poor contact. Hardwiring on PWB is broken.

Is 2.75 V or more applied to VAPP?

YES

NO

IC103 or Q103 is defective.

Can the SD card be formatted?

NO

SD card socket and CN104 are in poor contact. SD_CLK, SD_CMD, and SD_DAT [3:0] on PWB are broken or short-circuited. IC106 is defective or has come off.

YES

After formatting, can the SD card be used?

YES

NO

IC106 is defective or has come off.

File system on the SD card is damaged.

2 65

GX30

CONFIDENTIAL

18. IrDA (Infrared) communication is not possible.

Set the distance and angle within the specification for the IrDA communication.
NO

Check in IrDA inspection mode.

Is 2.8 V supplied from Q104 pin 2?

YES

IC106 is defective.

Is 2.8 V applied to UN101 pin 6?

YES

NO

Q104 is defective or UN101 pin 6 is soldered improperly. R183 is defective.

NO

Does the send signal (UN101 pin 5) send pulse waves periodically?
YES

NO

Is R183 good in appearance and mounted properly?

YES

IC106 is defective. R185 and C197 are defective.

NO

Is 3.0 V supplied from VCC (UN101 pin 1)?

NO

Are R185 and C197 good in appearance and mounted properly?

YES

YES

IC106 is defective. Is SD signal (UN101 pin 3) 0.2 V or lower?

YES NO

IC106 is defective.

Does the RxD signal (UN101 pin 4) send pulse waves periodically?
YES

NO

IrDA port (UN101) is defective.

Is UN101 good in appearance and mounted properly?

YES

NO

IrDA port (UN101) is defective or mounted improperly.

Is communication possible after replacing IrDA port (UN101)?

YES

NO

IC106 is defective.

IrDA port (UN101) is defective.

2 66

CONFIDENTIAL
19. Bluetooth communication is impossible.
A connection cannot be established via Bluetooth.
YES

GX30

Is 3 V supplied from IC505 pin 5?

YES

NO

IC505 is defective.

Is R514 (RESET signal side) always at H?

YES

NO

IC106 is defective.

Is waveform periodically sent from R516 (UARTTX signal side)?

YES

NO

IC506 is defective.

Is waveform periodically sent from R547 (UARTRX signal side)?

YES

NO

IC106 is defective.

IC506 is defective.

Handset can be connected to Bluetooth headset, but sound is not heard.

YES

Is waveform of PCMCLK signal (approx. 256 kHz clock) sent from R188?
YES

NO

IC106 is defective.

Is waveform of 8 kHz periodically sent from R550 (PCMSYNC signal side)?

YES

NO

IC106 is defective.

Is waveform of PCMIN signal periodically sent from TP508?

YES

NO

IC506 is defective.

Is waveform periodically sent from R515 (PCMOUT signal side)?

YES

NO

IC106 is defective.

IC506 is defective.

2 67

GX30
20. USB connection is impossible.

CONFIDENTIAL

Connect a properly working handset to the Data/USB cable that is not recognized. Is it recognized?
YES

NO

Reinstall the driver and replace the USB cable to connect the handset.

Is a communication with the handset established via SPST for GX30?

YES

NO

IC106, IC502, and IC504 are defective.

Connect to a Data with the USB cable.

Is TP536 at H?
YES

NO

The signal line from CN502 pin 8 to IC106 pin 90 is short-circuited with GND. Or R566 is has come off.

Is 5 V or more applied to TP515?

YES

NO

CN502 is connected improperly.

Is Q503 pin 3 at L?
YES

NO

Q503 is defective.

Is 3 V or more applied to TP166?

YES

NO

IC103 or IC106 is defective.

IC106 and IC502 are defective.

2 68

CONFIDENTIAL GX30 Phone Service E Market Manual 3. DISASSEMBLY AND REASSEMBLY CHAPTER
[1] Servicing Concerns
1. For disassembling
1. Please do not remove the board of base band section by pulling external interface connector, otherwise you will make damage to the board. 2. Shield case is attached on shield case holder without clearance. When you remove it, please take care not to remove together with shield case holder. If you remove shield case holder together, you can not attach it again because it is attached by solder and in such a case, you should have taken electric pattern on the board as well. MOUNT THE PWB

GX30

Key PWB-B (Rear Side)

Shield Case, BB

2. For reassembling
1. Please make sure that all cosmetic parts have no scratch and clean. 2. Please make sure that you can open and close handset smoothly and hear tick sound of hinges. 3. Please make sure that main screen display panel is placed in proper position without inclination. 4. Please make sure that all three battery terminals protrude evenly. 5. Please make sure that the pawl of aerial is upside.

NG

OK

OK

OK

NG

FASTENING TORQUE (Referential Value) Back Cabinet (Key)/ Front Cabinet (Key) Back Cabinet (Display)/ Front Cabinet (Display) 17.6 2 N cm (1.8 0.2 Kgf cm)

The PWB is set into the holes 1 and 2 . NG The PWB is out of the holes 1 and 2 .
STANDARD POSITION OF ATTACHMENT

The PWB is set into the hole 3 .

The value is for reference when an electric screwdriver (HIOS CL4000) is used. SOLDERING SPECIFICATION Soldering iron must be set to 350 C for 5 seconds. NOTES FOR REPLACING THE EARPIECE 1. When replacing the earpiece, make sure the earpiece sheets (B) are removed. Also, attach the earpiece sheet (A) to the specified position. 2. When replacing the front cabinet (display) with the earpiece sheets (B), replace the earpiece at the same time. 3. The earpiece sheets (B) is not supplied.

The PWB is out of the hole 3 .

When replacing the following labels (marked with put new ones on the specified positions.

), be sure to

Application range Standard position Standard position Standard position Cushion, Driver

Front Cabinet, Display

Standard position Earpiece Standard position Sheet, Earpiece (A)

Magnet

[Magnet/Cushion, Driver]

Standard position Camera Unit

Sheet, Earpiece (B)

Cushion, Camera Unit

Front Cabinet, Display

[Cushion, Camera Unit]

31

Application range

GX30

CONFIDENTIAL
Camera Relay FPC PWB-F Standard position Standard position

Key PWB-B (Rear Side)

Sheet, Aerial
Cushion, Connector

Shield Case end

SIM Connector end

[Sheet, Aerial]

[Cushion, Connector]

Standard position A

Standard position Sensor, Moisture Standard position

Sheet, Hinge Cover A Section A-A

[Sheet, Hinge Cover]

Front Cabinet, Key

Standard position Standard position Standard position Section A-A

Cushion, Battery

Key PWB-B (Rear Side)

Sheet, Side keys RF Shield Case end

[Cushion, Battery]

BB Shield Case end

External Display

[Sensor, Moisture/Sheet, Side keys]

Standard position Standard position

[External Display]

32

CONFIDENTIAL
Standard position

GX30
Standard position

Shield Case, BB

Standard position
Standard position

Spacer, Infrared Port

Section B-B

Insulator, BB

B A A

[Insulator, BB]

Tape, Infrared Port

Application range

Standard position

Standard position
Camera FPC PWB-F Standard position

Section A-A
[Spacer, Infrared Port/Tape Infrared Port]

Protect Sheet, Camera

Be careful to avoid contact of AN501 (Bluetooth aerial) with the Camera Ground FPC. Bluetooth aerial Standard position Camera Ground FPC PWB-D

Standard position
[Protect Sheet, Camera] [Camera Ground FPC PWB-D]

Key PWB-B (Rear Side)

33

GX30

CONFIDENTIAL
Back Cabinet (Key) Assembly
FIGURE 1

[2] Disassembly and reassembly

To reassemble, follow the reverse procedure. STEP 1 REMOVAL Back Cabinet (Key) Assy PROCEDURE 1.Battery Cover........ (A1)x1 2.Li-Ion Battery......... (A2)x1 3.Screw Cover.......... (A3)x2 4.Screw.................... (A4)x4 5.Hook..................... (A5)x4 6.Hook..................... (A6)x1 1.Stoper................... 2.Hook..................... 1.Aerial Cover.......... 2.Hook..................... (B1)x1 (B2)x4 (C1)x1 (C2)x1

(B1) x 1
3

SD Card Cover Belt Aerial

SD Card Cover Unit

3 4
Open the SD card cover and turn it as indicated by the arrow to release the stopper. Then pull out the cover downward. Remove the SD cover belt as instructed below.

SD Card Cover (A1) x 1

1

SD Card Cover Belt (B2) x 4

(A2) x 1 (A3) x 2 (A4) x 2 1.7 x 5 mm

PUSH 3 2

(A4) x 2 1.7 x 5 mm

PULL

Back Cabinet (Key) Assembly External Connector Cover

Figure 1

Figure 3

Back Cabinet (Key) Assembly (A5) x 2 2 SLIDE (A6) x 1 (C1) x 1 Aerial

1 PUSH 2 PULL

3
SWING

1 UP

(A5) x 2 Back Cabinet (Key) Assembly

Figure 4

(C2) x 1

2 SLIDE Jig Front Cabinet (Key)

(Use something flat and hard, for example guitar picks.) 1 Remove the external connector cover. Insert a jig into the slot and slightly lift up the back cabinet (key) assembly. 2 Insert jigs into the space. Slide jigs on the both sides to release 4 hooks (A5). 3 Move the cabinet assembly gently from side to side to release the other hook (A6).

Figure 2

34

CONFIDENTIAL
STEP 4 REMOVAL Key PWB-B PROCEDURE 1.Jack Cover 2.Side Key 3.Hook..................... (D1)x7 4.Solder................... (D2)x1 5.Flat Cable............. (D3)x3 1.Hook..................... 2.Hook..................... 1.Hook..................... (E1)x1 (E2)x2 (F1)x1 FIGURE 5

GX30
SD/SIM FPC PWB-G/ BB Shield Case

(D1) x 5

(D3) x 1
5 SD/SIM FPC PWB-G BB Shield Plate 6

(D2) x 1 (D3) x 2

Key PWB-B Jack Cover (Hands Free)

(D1) x 2 Side Keys

Key PWB-B

Back Cabinet (Display) Assembly

To unhook the key PWB-B, insert a small flat head screwdriver and lever it up as illustrated.

Hook Minus Driver

Figure 5

SD/SIM FPC PWB-G BB Shield Case (E2) x 2

(E1) x 1

Through the hole of BB shield case, push up the center of SD/SIM FPC PWB-G and release the hook (E1).

Figure 6

BB Shield Case

BB Shield Plate

Slide

(F1) x 1

Through the hole of BB shield case, push up the center of BB shield plate and release the hook (F1). Slide the BB shield plate to remove it.

Figure 7

35

GX30
STEP 7 REMOVAL Back Cabinet (Display) PROCEDURE Open the handset 1.Screw Cover.......... (G1)x3 2.Screw.................... (G2)x4 Close the handset 3.Hook..................... (G3)x4 4.Hook..................... (G4)x1 Open the handset 1.Hook.....................

CONFIDENTIAL
FIGURE 8

Back Cabinet (Display)

Front Cabinet (Display)

10

Main PWB-A Unit

(H1)x2
OPEN

(G2) x 2 1.7 x 5 mm (G2) x 2 1.7 x 5 mm

Figure 8

(G1) x 1

(G1) x 2

(G3) x 2 2 SLIDE

Back Cabinet (Display)

CLOSE

1
UP

Jig 3 (G4) x 1 2 SLIDE

(G3) x 2

1 Insert a jig into the gap and slightly lift up the back cabinet (display) assembly. 2 Insert jigs into the space. Slide them in the direction of the arrow to release 4 hooks (G3). 3 Being careful with the claw, release the hook (G4).

Figure 9

Main PWB-A Unit (H1) x 2

Front Cabinet (Display)

OPEN

Main PWB-A

To unhook the main PWB-A, insert a small flat head screwdriver and lever it up as illustrated.

Hook Minus Driver

Figure 10

36

CONFIDENTIAL
STEP 9 REMOVAL Main PWB-A PROCEDURE 1.Socket................... (I1)x1 2.Solder................... (I2)x3 3.Hook..................... (I3)x7 4.Flat Cable............. (I4)x3 1.Side Frame........... 2.Hinge.................... (J1)x1 (J2)x2 FIGURE 11

GX30
(I3) x 3 External Display/ External Display Holder Assembly

10

Front Cabinet (Key)/ Front Cabinet (Display)

12

(I4) x 3 Main PWB-A

(I2) x 2

(I2) x 1 (I3) x 4 (I1) x 1 Minus Driver Main Display Main Display/ Main Display Holder Assembly

Be careful dirt and dust do not get inside when replacing the display.

Figure 11

Front Cabinet (Key) (J1) x 1

PULL

Front Cabinet (Display)

(J2) x 2

Pinch hooks of the hinge with tweezers, etc. and push out the hinge. PULL PUSH

PUSH

Hinge

Tweezers
PULL

Figure 12

37

GX30

CONFIDENTIAL

GX30 Phone Service E Market Manual 4. DIAGRAMS CHAPTER [1] Block diagram
[Main]
RF I/F

VBAT AFCDAC, PA

IC103 AD6535 ANALOG BASEBAND

BASEBAND SECTION

CLKON, GPO_1 (TXON), GPO_9 (BS3), GPO_11(BS4) GPO_16 (BS1) GPO_17(BS2)

GPO_18 (SYNTHEN) GPO_20 (SYNTHDATA) GPO_21 (SYNTHCLK)

IP, INQP, QN Filter

DAC GMSK MOD

CLKI (13M

Filter ADC ADC Filter

DAC Filter Filter Ramp RAM

Baseband Serial Port BSIFS BSDI BSOFS BSDO GPO_1 (TXON), GPO_0 (RXON), GPO_5 (ASM)

IC106 AD6529 DIG

RAMP DAC

AFC DAC For BATTERY REFCHG REFOUT TH101 THERMISTOR TH701 THERMISTOR For CAMERA LIGHT1 LIGHT2 LIGHT3 x3 TEMP2 TEMP1 GPO_29(RESETABB) Light Controller Control Serial Port AUX ADC MCLKEN AUXADC2 REFEN, REF AIN3L A EP100 RECEIVER GPIO_36 VCORE VVCXO D AOUT3L D JK101 HANDS FREE CONNECTOR AIN1P/AIN1N MIC100 MICROPHONE AIN2P/AIN2N VMIC USB_VBUS VUSB VMIC LDO VABB LDO VUSB LDO VBACK LDO VRTC LDO VBAT SIM LDO VAPP LDO VCXO LDO VEXT LDO VMEM LDO VCORE LDO REGULATOR CONTOROL AOUT1P/1N AIN3R Tone Generator Voltage Reference BUFFER CLKOUT (13MHz) AUXRILY SECTION INTERRUPT LOGIC GPIO_37 (Interrupt) CSFS CSDI CSDO

MCU

BO R Se num

AOUT3R

Analog SW

PGA PGA

DAC DAC

Filter Filter Audio Serial Port

ASFS ASDI ASDO VINT nRESET IC108 R3112Q261A VOLTAGE DETECTOR 2.6V

PGA

ADC

Filter

AUDIO SECTION POWER MANAGEMENT SECTION POWER ON RESET GENERATOR

RESET VCHG

GPIO_8(Stereo / MONO DEC)

BATTERY CHARGER

IC116 RQ5RW45B
PWRON (DBBON), CLKON (VCXOEN) (LDOEN) VHGOSC, GATEDR CHGDACREF, ISEN REFCHG, VBATSEN

IC508 817A30NB
REG 3.0V

GPIO_7(Headset SW detect)

GPIO_48(Hook SW detect)

REG 4.5V

USC[5](CTS/Genie_Tx)

GPO_19(MODESEL3)

USC[0](Genie_Tx)

USC[4](RTS/Genie_Rx)

USC[6](GPIO_31 /Genie_Rx /RTC_monitor)

GPIO_10(DETECT)

KEYPADROW[4:0] KEYPADCOL[4:0]

USC[2](TxD)

USC[1](RxD)

USB D+

KEYON

KEYOUT

D505

GPO_4

VUSB

GPIO_39 (USB_PU_Control)

GPIO_11 FLIP-KEY VSIM LIGHT3 SIM CARD KEY PAD BACK LIGHT 3.0V / (1.8V) SIMD SIMC GPIO

USB D-

VINT

Q504

Manufacture(GPIO_09)

MODESEL1

MODESEL2

POWER-UP KEY

USB_VBUS KEYPAD:5 x 5

IC502 BU7870KN USB CONTROLLER

6 3 7 9 2 8 4

VIN LIGHT2 EN

IC503 TK73840 REG for USB p

5.2V/600mA from AC/DC CHARGER

5

CN502 EXTERNAL CONNECTOR

IC507 TC7SET00FU LOGIC

10

Figure 1 MAIN BLOCK DIAGRAM (1/2)

41

CONFIDENTIAL

GX30

GPO_7 (Power_on/off)

IC505 XC620930
REG 3.0V

IC506 UGNZ2 BLUETOOTH MODULE

GTDIO_B(RESET) RESET REG 3.0V

THEN) THDATA) THCLK) When JTAG=H, automaticaly GPO_18 TCK GPO_19 TMS GPIO_20 TDI GPIO_21 TDO JTAGEN

GPIO_3(RTS), GPIO_4(CTS), GPIO_33(RXD), GPIO_34(TXD) GPIO_14(PCM_CLK), GPIO_15(PCM_DATAIN) GPIO_16(PCM_SYNC), GPIO_17(PCM_DATAOUT)

IC708 TK11130C

CLKIN (13MHz)

BOOTCTRL[1] BOOTCTRL[0]

X101 32kHz CRYSTAL OSCIN OSCOUT

GPIO_47 (RESET) RESET ADD[2:1], ADD[19:17], DATA[15:0], nDISPLAYCS2, nWR, nRD, GPIO_13(CINT) VDD2

IC106 AD6529B DIGITAL BASEBAND

BSPORT ASPORT

AVDD CAMERA RELAY FPC CA1001 CAMERA UNIT CCD SENSOR DSP PART

15V -8V

B C

JTAG I/F DSP Subsystem SPORT-0 SPORT-1 Cipher Coprocessor PLL IDMA DSP ADSP-218x 78MHz Cache RAM (4k word) PM (16k word) DM (16k word)

IP PART V-DRIVER EXCKI VDD VDD6 REG 3.1V MP4RESET_B MODE

B)

HSL/ Trace

IC701 R116025B
REG 2.5V Controlled by VCORE

Viterbi Coprocessor

IC702 TK11131C

LCD1000 MAIN DISPLAY

MCUSubsystem SBUS

Cache (16k byte) DMA and BUS ARBITRATION

EBUS

nRD, GPO_10(BUFOFF) nWR, nDISPLAYCS1,nWAIT,GPIO_22(RSP) DATA[15:0],GPIO_6(LCDINT) GPIO_40(13M CLKOUT) GPIO_12 RESET REG 1.8V Controlled by VCORE

BOOT ROM Serial number

MCU ARM7TDMI 58.5MHz

CLK & BS GEN

PBUS Cpher Enginei

RBUS Internal SRAM (2Mbit x 2)

IC704 LR38863 DISPLAY CONTROLLER

VDDCORE VDDPLL

IC703 R116018B

DISPLAY DRIVER SE_D0, SE_LD2 SE,CK, PWM_LCD RESET

MMI SET

HOUSE-KEEPING System DMA WDT General Timers IRQ-CTRL & RAU

GSM-SYSTEM MicroSM Slow Clocking CSPORT Synth i/f

LCD001 EXTERNAL DISPLAY

GPIO DISPLAY RTC KEYPAD BMC SIM USC UART

VINT 3.0V REG 3.0V Controlled by VCORE

IC111 R1160N30B

DISPLAY BACK LIGHT EXTERNAL DISPLAY BACK LIGHT BLUE LED GREEN LED LEDCTL RED LED LIGHT1 VBAT

Peripheral Subsystem GPO_3(LED OFF) Peripheral PLL GPIO_38(INT), nWR,nRD ADD[1],DATA[15:0] GPIO_24(RESET), nAUXCS2 HP_OUTL HP_OUTR D EQ B C

IC707 BD6015 POWER VPLUS2 MANAGEMENT

CAMP CAMN

45B
), N) EN)

USB 1.1 Fast IrDA I2C Back light SPI(MMC)

LED

IC113 TC7SZ08A AND GATE

SPOUT1/2 SP100 SPEAKER REG 3.0V MO100 VIBRATOR

SC, GATEDRIVE, ACREF, ISENSE(ADC) G, VBATSENSE(ADC)

External Circuit For Charging

VCORE, VINT_ABB VMEM, VEXT VRTC, VSIM VUSB, VMC

IC105 YMU762C SOUND

IC109 NJM2871F03

ADDRESS & DATA BUS/GPIO (INT) GPO_8 SIMDATAIO SIMCLK GPIO_23(RESET) VMEM2.8V Q104 VAPP GPIO_0 (TxD) GPIO_1(RxD) SD_CLK SD_CMD SD_DAT[3:0] GPIO_5 (SD_DETECT) GPIO_35(SD_WP)

COMMON Flash memory

VSIM

SIM CARD 3.0V / (1.8V)

UN101 INFRARED PORT

SD

IC101 LRS1B27 5-LEVEL STACK MEMORY

SRAM 4Mbit(x 16) nGPCS2 VBACK P-SRAM 1 64Mbit(x 16) nRAMCS1

: nRD, nWR, ADD[23:1], DATA[15:0] : nROMCS1, GPO_22(VPP), ADD[0](WP), nRESET Super AND Flash : nGPCS1, nADV(ALE), nAUXCS1(CLE), GPO_2(WP for Super AND) SRAM, P-SRAM : nRAMCS1,nRAMCS2, nGPCS2, UBS, LBS, GPO_23(Sleep Control for PSRAM2)

VBAT

IC503 TK73840B REG for USB power

BATTYPE MP4_P0((LCDC port) Li-ION BATTERY 780mAh

P-SRAM 2 64Mbit(x 16) nRAMCS2 VINT 3.0V

Flash 128Mbit(x 16) nROMCS1

Super AND Flash 128Mbit(x 16) nGPCS1

BAT100 BACK-UP BATTERY

Figure 2 MAIN BLOCK DIAGRAM (2/2)

42

GX30

CONFIDENTIAL

[RF]

Rx LINE Tx LINE CONTROL LINE

BS1 (D) BS2 (D) BS3 (D) BS4 (D) PA (A) VBAT 2 6 1,3 TCXOEN (D) VRF TP801 VTCXO 36,41,42 23 24 25 26 TP802

(D): Digilal, (A): Analog

Power Supply
5

IC804 R5322N002B
IP (A) IN (A) QP (A) QN (A)

1,13,14,22,27,37,40,43,48

I&Q MOD DPD

TCXOOUT (D)

31

1/2 1/2 90deg shift (1/2)

TCX801 1 AFCDAC (A)

4 35 3 1/2 1/2 LOOP FILTER 28 IF Synthesizer 1/2 ARFCN 128 to 251 975 to 1023,0 to 9 10 to 124 512 to 670 671 to 885 512 to 810 PGA Part IFVCO 640 MHz 656 MHz 640 MHz 640 MHz 656 MHz 640 MHz RF

26MHz VCTCXO 2

GSM850 GSM900 DCS1800 PCS1900

90deg Shift(1/2)

2,5,8,11,15,16,18 PGA

90deg Shift(1/2) (D) SYNTHEN SYNTHDATA (D) SYNTHCLK (D) 29 32 30 Serial data interface

IC801 HD155155NP RF

Figure 3 RF BLOCK DIAGRAM (1/2)

43

CONFIDENTIAL

GX30

BS2 BS3

1,2 5

IC805 NL17SZ32XV5T2 LOGIC

LOOP FILTER 12

Tx VCO GSM850 824.2 to 848.8 MHz GSM900 880.2 to 914.8 MHz DCS1800 1710.2 to 1784.8 MHz PCS1900 1850.2 to 1909.8 MHz

VBAT 3,6,13

BS2 17 2 16

IC802 PF08141B PA MODULE

12 1800 / 1900

BS1 BS2 BS3 BS4

19

18 PA

17 PD

850 / 900

4,5,8,9,10,11,14, 15,19,20,21,22,23 APC RFVCO Tx GSM850 GSM900 DCS1800 PCS1900 Rx GSM850 GSM900 DCS1800 PCS1900 38,39 LOOP FILTER AERIAL

RF Synthesizer

3616.8 3848.8 3580.4 3860.4 3476.8 3700.8 3610.4 3860.4

to to to to to to to to

3715.2 MHz 3979.2 MHz 3729.6 MHz 3979.6 MHz 3575.2 MHz 3839.2 MHz 3759.6 MHz 3979.6 MHz

15

13

11 6,10,12,14 RF CONNECTOR 2 9 1 J801

3,7,8,16 FL901 SAW FILTER 4 1 GSM850 Rx 1 2 4 5 3,4 FL803 RF SWITCH GSM850 Band; Tx: 824.2 to 848.8 MHz Rx: 869.2 to 893.8 MHz GSM900 Band; Tx: 880.2 to 914.8 MHz Rx: 925.2 to 959.8 MHz DCS1800 Band; Tx: 1710.2 to 1784.8 MHz Rx: 1805.2 to 1879.8 MHz PCS1900 Band; Tx: 1850.2 to 1909.8 MHz Rx: 1930.2 to 1989.8 MHz 1 4 2,5 PCS Rx

FL904 9 10 1 0deg ft(1/2) LNA 9 5

10

3 2,5

MATCHING 3,8 DEVICE 7 6 2 1

9 GSM900 Rx FL902 SAW FILTER 6 DCS Rx

7 LNA 6 0deg ft(1/2) 4 LNA 3

3 4 5,7,8,10 3

FL903 SAW FILTER

Figure 4 RF BLOCK DIAGRAM (2/2)

44

GX30

CONFIDENTIAL GX30 Phone Service E Market Manual 5. SCHEMATIC DIAGRAM AND WIRING SIDE OF P.W.BOARD CHAPTER
[1] Notes on schematic diagram
Resistor: To differentiate the units of resistors, the symbols K and M are used. The symbol K means 1000 ohm and the symbol M means 1000 kohm. The resistor without any symbol is an ohm resistor. Capacitor: To indicate the unit of capacitor, the symbol is used. The symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression capacitance/withstand voltage is used. (CH), (RH), (UJ): Temperature compensation (ML): Mylar type (S): Styrol type (PP): Polypropylene type The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. Conditions: SIM card inserted, power on, in stand-by mode (opened) Schematic diagram and Wiring Side of P.W. Board for this model are subject to change for improvement without prior notice. Parts marked with are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

[2] Types of transistor and LED

B (3) (G) E (1) (S)
1 8

TOP VIEW

C (2) (D)

D D G

TOP VIEW
3 4

D D S

S1 G1 S2 G2
4

D1 TOP VIEW D1 D2 D2 ECH8603

5

1 (D) 2 (D) 3 (G)

TOP VIEW

6 (D) 5 (D) 4 (S)

PD PD
3

TOP VIEW EC4301 C EC4401 C

PG PS
2

2SK3019 RT1N144 U

CPH6311

MCH6413

TOP VIEW

TOP VIEW

TOP VIEW

TOP VIEW

1SS388 1SS405 MA2SD31 MA2SD32 RB160M30 RB521S30 RB551V30

HN2S01FU

GM56271A

RSB6.8S

TOP VIEW

TOP VIEW

TOP VIEW

GP2W0116 YPY1105C NECW008A

51

CONFIDENTIAL
[3] Waveforms of circuit
RF Test Tool Tx test Data pattern...TSC 5 RF Test Tool Tx test GSM850, GSM900 Band

GX30

1 2 3 4

IP C811 (IC801 23Pin) IN C811 (IC801 24Pin) QP C812 (IC801 25Pin) QN C812 (IC801 26Pin)

8 9 10 11

BS1 C870 (FL803 10Pin) BS2 C871 (FL803 6Pin) BS3 C872 (FL803 12Pin) BS4 C874 (FL803 14Pin)

RF Test Tool Rx Test channel_62, Gain 64 dB, SniffOFF

RF Test Tool Tx test DCS1800, PCS1900 Band

1 2 3 4

IP C811 (IC801 23Pin) IN C811 (IC801 24Pin) QP C812 (IC801 25Pin) QN C812 (IC801 26Pin)

8 9 10 11

BS1 C870 (FL803 10Pin) BS2 C871 (FL803 6Pin) BS3 C872 (FL803 12Pin) BS4 C874 (FL803 14Pin)

RF Test Tool Rx Test GSM900 Band (channel 62)

RF Test Tool Rx test GSM850 Band

5 6 7

SYNTHEN R835 (IC801 29Pin) SYNTHCLK R836 (IC801 30Pin) SYNTHDATA R837 (IC801 32Pin)

8 9 10 11

BS1 C870 (FL803 10Pin) BS2 C871 (FL803 6Pin) BS3 C872 (FL803 12Pin) BS4 C874 (FL803 14Pin)

52

GX30

CONFIDENTIAL
RF Test Tool Rx test GSM900, DCS1800 Band

12

13M-IN (CLKIN) (Stand-by)

C833 (IC106 142Pin)

8 9 10 11

BS1 C870 (FL803 10Pin) BS2 C871 (FL803 6Pin) BS3 C872 (FL803 12Pin) BS4 C874 (FL803 14Pin)

13

13M-OUT (CLKOUT) (Stand-by)

R166 (IC106 84Pin)

RF Test Tool Rx test PCS1900 Band

8 9 10 11

BS1 C870 (FL803 10Pin) BS2 C871 (FL803 6Pin) BS3 C872 (FL803 12Pin) BS4 C874 (FL803 14Pin)

14

OSCIN (32 kHz) (Stand-by)

R174A (IC106 49Pin)

15

DCLK (Stand-by)

R750 or C758

53

CONFIDENTIAL
16
VSYNC (Stand-by) C760

GX30

17

SUBFLM (Stand-by)

L711 1Pin

18

TCXOEN (Stand-by)

IC804 1Pin

54

GX30

CONFIDENTIAL

[4] Schematic diagram/Wiring side of P.W.Board

MAIN PWB-A
A

CAMERA GROUND FPC PWB-D

Battery VBAT

TO KEY PWB-B (1/3)

5-19 (6-A)
C705 1
1 2 3 G Vdd GND CE

MAIN PWB-A
B
TP703

RECEPTION SIGNAL TRANSMISSION SIGNAL SPEAKER SIGNAL

C792 0.1

(4-C)
CAM_CTL

R758 0
C795 1

TP736

TP704

Vin

Np(Vref) Vout

GND

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 LCD_INT /LCD_RESET /LCD_WAIT DATA[8] DATA[9] 3.0V VINT VBAT_BL /LCD_CS RECEVER_P RECEVER_N TP702 TP701 TP738

CN701

(6-B)
CAM_CTL G

GND

Cont

SP100 SPEAKER

IC708 TK11130C REGULATOR

R761 0

C706 0.001
G

GND GND GND GND GND SP+ SPGND GND AGND

RECEIVERRECEIVER+ AGND LCDCS VBAT VBAT VBAT VINT VINT

LCDWAIT

FROM CAMERA RELAY FPC PWB-F

D8 D9 AVDD(3.1V) VDD6(3.1V) VDD4(-8V) VDD3(+15V) GND LCDCLK GND CAMCK GND GND D3 D2 D1 D0 WE

5-30 (12-B

G)

C746 1

C743 1

LCDINT LCDRESET

C794 0.01
Battery VBAT_L

R704A 0

LCDCLK

CAMCK

C741 1

31 30 DATA[3] 29 DATA[2] 28 27 26 25 24 23 22 DATA[5] 21 DATA[6] 20 19 18 17 16 15 14 13 USB C CNT DATA[14] LCD_RSP DATA[13] BUFOFF DATA[12] DATA[7] VCCD DATA[4] 13M_CLK /WE /RD DATA[1] DATA[0]

RD VCCD D4 D5 D6 D7 BUFOFF D12 LCDRSP D13

BTRESET D14

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6

Figure 1 SCHEMATIC DIAGRAM (1/22)

55

C742 1

C740 1

CONFIDENTIAL

GX30

IC701 R116025B 2.5V REGULATOR

TP709 3.0V VINT 1 2 3 Vdd GND CE ECO 4 Vout 5 TP705

IC703 R116018B 1.8V REGULATOR

1 Vdd GND CE ECO 4 Vout 5

C718 0.1

C722 1

C709 2.2

R705 0

C728 1

R756 0

R743 0

2 3

C706 0.001

R720 1

Vout 4

Vin

IC702 TK11131C REGULATOR

C721 0.01

5-11 (5-F)
CAM_3V_CTL

Np(Vref)

R712 0

GND

Cont

BUFOFF

BUFOFF

TP7

) : Not Mount
7 8 9 10 11 12
Figure 2 SCHEMATIC DIAGRAM (2/22)

56

GX30

CONFIDENTIAL

MAIN PWB-A
D13 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 LIGHT1 DATA[10] LED DATA[11] USB_C_CNT DATA[15] DATA[14] DATA[13]

BTRESET D14 USB_C_CNT D15 LED D11 LIGHT1 D10 REFOUT VCORE

TEMP VBAT VBAT VBAT

CN701

R760 470K

FS701 0.63A

TH701 10K THERMISTOR

R703 10K

FS702 1.25A C701 4.7 L702 4.7H D703 RB551V30 C703 4.7

L701 4.7H

LED702 GM56271A
G 4 R 5 B 6 1 2 3

D
C704 1

MOBILE LIGHT

E
R718 3.3

D702 MA2SD31

R701 3.3K

C713 2.2

TP727

TP728

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 3 SCHEMATIC DIAGRAM (3/22)

57

D701 MA2SD32

C708 22

D704 C707 MA2SD31 1

C702 0.47

CONFIDENTIAL

GX30

TP732

R744 0

3.0V VINT

TP733

R707 0

R745 0

C724 2.2

C714 4.7

C726 2.2

C711 47P(CH) C712 47P(CH)

C719 0.1

NC

6 R 3 2 1 5 4

1 2
VIO CAPP1

CAPP2

CAMP

CAP3

OBILE GHT

R704 0.1

12 15 16 21

CAPN1

CAPN2

VBAT1

VBAT2

CAMN

CPIN

44

20 18

13

14 19

22 17

NC

D702 56271A

Q702 MCH6413

27 38

TRSW SENSP SENSN VPLUS2

IC707 BD6015 POWER MANAGEMENT

1 2 2 10 16 21 25 29 33 40 41 34 42 35 43 36 44 3 3 11 4 4 12 17 5 5 6 86 7 7 13 18 22 26 30 37 45 14 19 23 27 31 38 46 8

RSTB 40 DATA 28 STRB 24 CLK 25 FRP 29 TP734 TP735

TP737 TP729 TP730 TP731 10 2 11 42 45 26 41 34 LEDR LEDG LEDB SW VPLUS11 VPLUS12 BLED FLED SBD VNEG A B C D E F G H

1 9 15 20 24 28 32 39

ERROUT 33

NC

BACK LIGHT FPC PWB-C

TP710

LSO11 LSO12 WVOUT

5 6 7

NC NC

CN705
1 2

D704 C707 MA2SD31 1

37

LEDCTL 32
GNDP GND1 GND2 GND3 TEST IREF T1 T2 T3 T4

C725 0.1

3 4 TP711

46

39

30

35

23

43

R708 120K

TP706

C708 2.2

TP707

D705 MA2SD31

C710 2.2

TP708

EP100 EARPIECE
TP721

TP722

) : Not Mount
7 8 9 10 11 12
Figure 4 SCHEMATIC DIAGRAM (4/22)

58

C790 0.01

C791 0.01

36

VREF 31

GX30

CONFIDENTIAL

MAIN PWB-A
A
LCD001 EXTERNAL DISPLAY
R716 0
5
RESB GND GND CSB

TP714

1.8V VLCD

C729 1

33

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

R713 1

R728 0

VINT

R723 0
C751 100P(CH)

/LCD_RESET

BUFOFF

L711 FERRITE BEADS

/LCD_CS

/LCD_WAIT

LCD_INT

BUFOFF

VLCD

/LCD_RESET

LCD_RSP

SUBWR

SUBFLM

SUBCS

SUBRS

SUBCKS

SUBCK

SUBD1

SUBD7

C787 100P(CH)

L746 FERRITE BEADS

R748 0

R747 0

DATA[9]

DATA[8]

DATA[7]

DATA[6]

DATA[5]

DATA[4]

DATA[3]

DATA[2]

DATA[1]

DATA[15]

DATA[14]

DATA[13]

DATA[12]

DATA[11]

E
22
CS_B

DATA[10]

DATA[0]

R732 470K

17

34
WR_B

46 121 24 131 120 119 118 108 107 106 96

DB11 DB9 RD_B LCDINT DB15 DB14 DB13 DB12 WAIT_B BUFOFF_B DB10

95
DB8

94
DB7

93
DB6

81
DB5

72
DB4

71
DB3

70
DB2

69
DB1

60
DB0

47
RSP

21
SUBCS_B

17
SUBWR_B

35 136 122 110 123 78

SUBFLMIN SUBCKS SUBRS SUBDB7 SUBDB5 SUBLPIN

66
SUBDB3

SUBD3

SUBLP

C736 0.01

L749 FERRITE BEADS

56 RESET_B

TP713

R705A 0
54 XIN XOUT

TP712 3

FL701 NA004 2
1 4

NC

42

85

CAMCK

C732 0.1

C737 0.1

VDDPLL

15 19

VDDCORE VDDCORE 1 2 2 14 26 38 50 62 74 86 98

IC704 LR38863 DISPLAY CONTROLLER

3 3 15 27 39 51 63 75 87 99 4 4 16 28 40 52 64 76 88 100 5 5 17 29 41 53 65 77 89 101 6 6 18 30 42 54 66 78 90 102 7 7 19 31 43 55 67 79 91 103 8 8 20 32 44 56 68 80 92 104 9 9 21 33 45 57 69 81 93 105 10 10 22 34 46 58 70 82 94 106 11 11 23 35 47 59 71 83 95 107 12 12 24 36 48 60 72 84 96 108

74

VDDCORE VDDCORE VDDCORE A B C D 1 13 25 37 49 61 73 85 97

G
3.0V VINT

84 90

139 VDDCORE

C734 0.1

C739 0.1

143 VDDCORE

23

VDDIO E VDDIO VDDIO VDDIO G VDDIO H F

R717 0

26 43 76 82

H
97

VDDIO

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 5 SCHEMATIC DIAGRAM (5/22)

59

SUBDB4

L710 FERRITE
67

/WE

/RD

SUBCKS

SUBFLM

SUBWR

C744 1 C745 1 C747 1 C748 1 C750 1

SUBCS

SUBRS

R729 0

R730 0

R727 100K

SUBCK

SUBD0

SUBD1

SUBD2

SUBD3

SUBD4

SUBD5

SUBD6

SUBD7

SUBLP

CKS

WR

RD

FLM

RS

D1

D4

V1

V2

V3

CK

D0

D2

D3

D5

D6

D7

LP

V0

V4

CONFIDENTIAL

GX30

CAPA1+

CAPA2+

13

12

11

10

7
TP717

CAPA3+

CAPA1-

CAPA2-

CAPA3-

VREG

VOUT

GND

VDD

CKS

FLM

CK

C756 1

C753 0.1

L710 FERRITE BEADS

SUBCKS

SUBCK

C752 0.1

L709 FERRITE BEADS

C754 1

C755 1

C757 1

CN703

SUBD1

SUBD7

SUBD3

SUBD6

SUBD4

SUBD5

SUBD2

SUBD0

IC706 TC7SZ08A LOGIC

5 Vcc 1 2 4 GND 3

23 78
SUBCKS SUBDB5

66
SUBDB3

67
SUBDB4

27
SUBDB1

80
SUBCK

55
SUBDB6

57
SUBDB0

58
SUBDB2

CN704 C770 4.7

1 2 G0 G1 G2 G3 87 86 77 65 60 T-COM T-COM TFT-COM COMC COMC COMDC VCOMH B0 B1 B2 B3 B4 B5 G0 G1 G2 G3 G4 G5 R0 R1 R2 R3 R4

C769 1

L734 FERRITE BEADS

3 4

R740 56K C784 4.7

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

G4 G5 R4 R2

64 63 89 99

B0

L735 FERRITE BEADS

B1 B2 B3 B4 B5

R0 101 R1 100 R3 R5 98 88

L736 FERRITE BEADS

G0 G1 G2 G3

B5 B4 B3 B2 B1 B0

28 29 30 38 39 40

G4

L733 FERRITE BEADS

G5 R0 R1

L714 60(100MHz) L715 60(100MHz)

R2 R3 R4 R5 23 24

) : Not Mount
7 8 9

The number 17 is waveform number shown in page 5-4.

10 11 12
Figure 6 SCHEMATIC DIAGRAM (6/22)

5 10

GX30

CONFIDENTIAL

MAIN PWB-A
G 82 VDDIO H 97 VDDIO J K L M 4 5 14 PLLDIV0 PLLDIV1 PLLDIV2 PLLGND GND GND GND GND GND GND 85 97 109 121 133 86 98 110 122 134 87 99 111 123 135 88 100 112 124 136 89 101 113 125 137 90 102 114 126 138 91 103 115 127 139 92 104 116 128 140 93 105 117 129 141 94 106 118 130 142 95 107 119 131 143 96 108 120 132 144 73 74 75 76 77 78 79 80 81 82 83 84

115 VDDIO 132 VDDIO 135 VDDIO 45 SCANEN

3 16 18 31 44 48 75

83

GND
PWMLCD/PORT4 SE_LD3/PORT6 SE_LD2/PORT5

111 GND
PWM0/PORT3

127 GND
DUMMY4 DUMMY3 DUMMY2

PWM1/PORT8

BSPIXEL7

BSPIXEL6

BSPIXEL5

BSPIXEL4

STKCHK

BSHS_B

BSVS_B

HSWRD

HSD0

HSD1

HSD2

HSD3

HSD4

HSD5

HSD6

HSD7

11 P(CH) 12 P(CH)

12 133 144

134 130

73

32

11

10

49

61

59

37

68

20

91 13
NC

33 105 92

79 104 116 128 126 138

TP716

710

LED703 NECW008A

TP715

TP723

TP724

C791 0.01

LED704 NECW008A

G CAM_3V_CTL

5-6 (7-C)

TP711

C790 0.01

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 7 SCHEMATIC DIAGRAM (7/22)

5 11

BSCLK

142 GND

BSPIXEL3

BSBLK_B

DUMMY1

TESTI

HSCK

HSEN

CONFIDENTIAL

GX30

B1 B0

39 40

L714 60(100MHz) L715 60(100MHz) R750 0

R2 22 R3 R4 R5 23 24 25 26 R2 R3 R4 R5 DCLK HSY VSY SO SI SCLK CS RESET VCC GND GND VDC VDC COM2 VCL AM VSS2 VSS1 NC VDD2 C5C5+ C4C4+ C3C3+ C2C2+ C1C1+ VDC2 VDC2 VR VS VS 61

15

16
TP718

DCLK HSYNC VSYNC SE_DI/PORT7 SE_DO/PORT0 SE_CK/PORT1 SE_LD1/PORT2

50 HSYNC 52 51 140 117 129 141 TP719 VSYNC NC

27

C758 10P(CH)

C760 10P(CH)

28 29 30 31 32

R714 470K

33 34

C761 10P(CH)

C759 10P(CH)

EXCS_B0 EXCS_B1 EXCS_B2 EXCS_B3

103 41 62 53

NC NC NC NC

3.0V VINT

R737 0

C774 2.2

35 36

R738 0 D709 RB521S30

C775 4.7

37

R741 0 D710 1SS405

38 39 40 41 42

DCS_B DA1
MP4 RESET_B MP4_PLLCK

114 124 112

C771 1 C773 1

DA0

BSPIXEL6

BSPIXEL5

BSPIXEL4

BSPIXEL3

BSPIXEL2

BSPIXEL1

BSPIXEL0

C772 1 C776 1 C777 1

TP720

NC

43 44 45 46 47 48

GTDIO_B

16 128 126 138 137 125 113

36

25 102 109
NC

MP4_P0

NC

49 50

C766 0.01

C779 4.7 C780 4.7 C781 4.7 C782 2.2 C783 4.7

51 52 53 54 55 56 57 58 59

) : Not Mount
7 8 9

The numbers 15 , 16 are waveform numbers shown in pages 5-3 ,5-4.

10 11 12
Figure 8 SCHEMATIC DIAGRAM (8/22)

5 12

LCD1000 MAIN DISPLAY

GX30

CONFIDENTIAL
MAIN PWB-A (FRONT SIDE)

A
TP722 TP721 TP734

TP735

TP715 TP723

EP100 EARPIECE

TP732

TP733 TP716 TP707

TP724 TP710

TP706

TP714

TP711

TP720

TP712

E
TP717

TP737 TP713 TP731 TP729 TP705

TP736

TP730 TP709

TP728

TP727

TP702

TP738

TP701

R704A

FS702

FS701

R760

30

25

20

15

10

5-31 (6-A)

CN701
40 45 50 55 60 31 35

FROM CAMERA RELAY FPC PWB-F

C740

C741

C743 C746 C742

Figure 9 WIRING SIDE P.W.BOARD (1/5)

5 13

CONFIDENTIAL
MAIN PWB-A (REAR SIDE)
15
TP718

GX30

16

17

FL701 C739
C774 C775

C734 R717 C737

R750 C758

C760 R705A
L709 L711 L710 R707 L749

C711 C712 C791

D710 R737

C719 R708

L734

C769

FROM BACK LIGHT FPC PWB-C

C770 C772

CN705

R738

L733

IC704

C736

5-31 (3-A)

C790

L715 L714

C771

R744 R745
C726 C714

IC706
4 3 1

C777 D709 R714 L736 L735

R740 C773

L746 C787 R747

TP708

C779

C724

R741

C784

C725

C766

C776

TP719

C761 C759

C732 R732 LED703

R748 IC707

LED704

1 5

C707

D705

10 15 20 25

D704

C710 C708

35 40 45 50 55 59

C713

FROM LCD1000

CN704

5-31 (4-F)

R718

30

C702

R704 D703 Q702

C704

L702

L701

C783

C782

C703 C757 C780

C701 C756

C753 C755
1 5

D701

D702

5-31 (6-H)

FROM LCD001

R716

C729

R713

CN703 R730 R729

IC703
1 3

10 15

C728

R743

20

R705

R720 R712 C721

LED702
1 1

IC708
5 4

25

C792 R758 C795 SOLDER C752 R723

R701

30 32 33

C709

R728

C705
R703

C718

3 5 C706 4 R756

C781 MOBILE LIGHT

C751 R727 C747

C722
R761

C748
C745

TH701

5-31 (2-C)

FROM CAMERA GROUND FPC PWB-D

SOLDER

C744

IC702

C750

IC701

C794

C754

5-31 (2-C)

TP704

B FROM CAMERA
GROUND FPC PWB-D

SP100 SPEAKER
TP703

SOLDER

5-31 (5-B)

E FROM CAMERA
RELAY FPC PWB-F

The numbers 15 to 17 are waveform numbers shown in pages 5-3 ,5-4.

7 8 9 10 11 12
Figure 10 WIRING SIDE P.W.BOARD (2/5)

5 14

GX30

CONFIDENTIAL

KEY PWB-B (1/3)

A

KEY PWB-B (1/3)

RECEPTION SIGNAL TRANSMISSION SIGNAL SPEAKER SIGNAL

5-23 (6-B)

KEYPADCOL[0-4],KEYPADROW[0-4],POWONKEY G

5-23 (4-G) 5-23 (6-E)

MODESEL3 G USB_D+ USB_DG G

MODESEL3 USB_D+ USB_D-

MODESEL2

R292 150K

R294 120K

5-23 (6-E) USB_PU 5-23 (2-F) 5-23 (2-G) 5-23 (4-G) 5-23 (6-D)
USC[1]

5-23 USB_DET (6-E)

USC[0]

USB_DET USB_PU

5.2V CHGIN

USC[0] USC[1]

R293 150K

R295 120K R281 0

USC[4]

USC[5] USC[6] G G

USC[6] USB_CURRENT_CTL
Vin

G1 S2 G2

D1 D2 D2

GND Vout

USB_CURRENT_CTL G USB_CHG_EN

R282 1.8K

C229 0.001

TP103 TP104

USC[0] USC[1] USC[2]

R283 2.2K

Q108 ECH8603

NC

3
NC

TP105 TP118 TP107 TP108 TP109

USC[4] USC[5] USC[6]

TCXOEN

5-25 (1-B)

TCXOEN TP180 BS1 G BS1 BS2 BS3 G BS3 BS4 SYNTHCLK G TP114 TP115 SYNTHEN G TP116 SYNTHCLK SYNTHDATA SYNTHEN 2 VDD VOUT 3 1 GND CE 4

5-25 (2-H)

BS2

IC116 RQ5RW45B 4.5V REGULATOR

D106 RB521S30

R131 270 D103 RB160M30

3.53V D

BS4

5-25 (2-E)

G SYNTHDATA

C235 1

C236 1

Q101 2SK3019
S 3.69V

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 11 SCHEMATIC DIAGRAM (9/22)

5 15

R128 91K

5-23 (6-C)

BATTYPE G

3.53V

3.54V

USC[5]

0V

5-23 (5-F)

USC[2]

USC[2] USC[4]

IC115 XC61CN27 REGULATOR

R284 27K
0V S1 D1 0.15V 0.15V 3.69V 3.69V

3.52V G

CONFIDENTIAL

GX30

C226 0.047

R278 27K

C148 0.047

R142 27K C154 220P (CH)

C152 0.1

R145 68K R146 18K

C157 0.047

MO100 VIBRATOR

VBAT

R139 0
C149 4.7

3.0V VAPP VINT 2.85V VSIM

R15 0

R158 0

M
5-22 (11-C)
SP1-1 G SP2-1 G TP126 TP127

SPVSS 16

SPVDD 15

EQ3 14

EQ2 13

EQ1 12

HPOUT-R 11

HPOUT-L/MONO 10

C168 0.1 C169 0.1 R159 C171 3.3K 0.001

NC

R135 0 R136 0
DATA[7] DATA[6] DATA[5] DATA[4] DATA[3]

17 SPOUT1 18 SPOUT2 19 MTR 20 D7 21 D6 22 D5 23 D4 24 D3 25 D2

VREF VSS VDD PLLC

9 8 7 6 5 4 3 2

IC109 NJM2871F03 3.0V REGULATOR

VBAT 1 2 3 CONT VIN GND NB VOUT 4 5

C143 0.1

IC105 YMU762C SOUND

32 IOVDD 28 /WR 31 /RD 29 /CS

N.C. /RST /IRQ LED CLK1

R161 0
R160 470K

DATA[2]

TP113 TP111

C139 0.1 L113 FERRITE BEADS

D105 1SS388 C142 1

26 D1

27 D0

30 A0

C231 47P(CH)

TP112

DATA[1]

DATA[0]

MODESEL2,MODESEL3,USB_CURRENT_CTL,USB_D+,USB_D-,USB_DET,USB_PU,USC[0-2,4-6]

C215 0.1

3.0V VINT

NC D1 D1 D2 D2
8

1 2

NC

Vcc

1 2

Vcc 5

0.15V 0.15V 3.69V 3.69V

IC113 TC7SZ08A AND GATE

3 GND

3 GND

R152 0 3

POWONKEY

C170 0.1

USC[3]
KEYPADROW[4]

POWONKEY

/CAM_RESET

C210 0.1

C167 4.7

R285 470K

VBAT

IC111 R116030B REGULATOR

1

KE KE KE

R239 0

3.0V VINT

KE KE KE KE KE KE 3.0V VINT KE

C213 1

Vdd GND CE

Vout

R133 0.18

2 3

ECO

C214 1 TP173 R238 1

3.52V G

C141 0.0047 R286 470K R134 100

R256 0 C144 10 C145 C146 0.1 0.1

5.0V VBUS_IN

3.0V VINT

R137 0

USC[0] USC[1]

R162 0
V USC[3]

C147 0.1

USC[2]

NC

NC

R138 0

USC[4] USC[5]

) : Not Mount
7 8 9 10 11 12
Figure 12 SCHEMATIC DIAGRAM (10/22)

5 16

GX30

CONFIDENTIAL

KEY PWB-B (1/3)

A
G IN QP G QN G G IP IN QP QN PA AFCDAC G AFCDAC IP IN QP QN PA RECIVER_OUTP 12 13 15 14 28 30 I I Q Q P A

5-25 (2-D) 5-25 (3-A)

IP

PA

5-25 (2-F)

R128 91K

5-23 (6-C)

BATTYPE G

AFCDAC

5-22 (11-B)

RECIVER_OUTP RECIVER_OUTN

C116A 1 C120A 1

L107 93 A FERRITE C132 94 A BEADS 47P(CH)

59 A A

VINT

C115 47P(CH)

R248 0

Q106 EC4301 C
3 2 2

Q107 EC4401 C
3

RECIVER_OUTN VBAT L108 FERRITE BEADS C120 47P(CH)

63

106 S 90 91 S A

3.01V

PS

PD

0V

NS

ND

R264 0

TP121 2.98V
4 1 1

R277 0

PG

PD

NG

ND

C
TP101

C107 22/4 C228 2.2 C110 22/4

TP176

107 A 89 A 105 A 60 A

C108 10

R280 470K

C232 47P(CH)

R129 2.2K

R130 2.2K

R115 100
R125 2.2K

C121 47P(CH)
VMIC

C122 47P(CH)

R124 NC 0
NC

TP119 L101 C101 47P(CH) FERRITE BEADS

R126 64 A 0
76 80 96 79 95

TP102

MIC100 MICROPHONE

TP160 TP161

R262 6.8K

C113 0.001

C117 0.001

ZD101 RSB6.8S 6.8V

L102 FERRITE BEADS V101 100P

C104 47P(CH) R112 0

TP120

R263 6.8K

C112 47P(CH)

C126 0.1 C116 47P(CH) C133 47P(CH) C127 0.1 C134 47P(CH)

V A A A A

R122 2.2K

68 71 72 75

L L L L

D
JK101 HANDS FREE CONNECTOR
6 5 2

TP162 1.8V VCORE 2.75V VT 2.75V VT TP177 TP179 REMOTE_SW STEREO_SW HEDSET_DET

R191 470K

R244 1K R245 1K

R132 100K

R192 470K

R127 470K

C118 26 A 0.1
9 A R T R T 27 25 39 8

C103 0.1

V106 650P

R148 10K

V104 650P

V124 650P

C105 0.1

TH101 10K THERMISTOR

ZD104 RSB6.8S 6.8V

AUDIO_IN G

L105 FERRITE BEADS

TP163

V109 650P

4 1

R246 1K R104A 0 L103 FERRITE BEADS

2.75V VT 1 2 3 GND 4 Vcc 5

C224 0.1

113 A 114 A 115 A

TP178

VABB

116 A 117 A 118 A 119 A 120 A

VMIC

5-23 (5-G)
AUDIO_OUT

C223 1

121 A 122 A 123 A 124 A 125 A

G 2.5V VMIC

R268 120K

C222 0.1

C220 0.1

IN(+) Vss IN(-)

Vdd

F
REFOUT G

R266 470K R267 68K

C221 0.1 C219 0.1

126 A 127 A

2 3

Out

128 A 129 A 130 A 131 A

5-20 (11-G)
VBAT

TEMP1 G

IC114 HA1631S03CME COMPARATOR

R110 560

R178 560

R103 180

R104 560

R106 560

R107 560

LED103 YPY1105C GREEN

R111 560

R190 560

LED106 YPY1105C GREEN LED107 YPY1105C GREEN

LED118 YPY1105C GREEN

TP174

LED104 YPY1105C GREEN

5-25 (2-E)

TCXOOUT G

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 13 SCHEMATIC DIAGRAM (11/22)

LED110 YPY1105C GREEN

LED111 YPY1105C GREEN

5 17

LED119 YPY1105C GREEN

LED109 YPY1105C

CONFIDENTIAL

GX30

USC[1]

C147 0.1

USC[2]

V USC[3]

NC

NC

R138 0

USC[4] USC[5]

24

22

21

23

92

52

35

51

55

19

85

84

74

82

78

47

86

USC[6]

VCHG(VCHGIN)

CHGDACREF

ISENSE

GATEDRIVE

VBATSENSE

BATTYPE

CHGOSC

NC_G16

VUSBIN

VBAT1

VBAT2

VBAT2

VBAT3

VBAT3

VBAT4

VBAT5

NC_R12

VMEMIN

VCOREIN

VMEMIN

VRTCIN

KEYON 110 KEYOUT 109 CRST 81

JTAGEN TCK TMS TP164 VABB

12 13 15 14 28 30

IP IN QP QN PA AFCDAC

VBACKSEL 101 VMEMSEL 83

C153 0.1

TDI TDO TP169

C158 2.2 C159 1 C160 1 C161 1

C162 0.47
VBAT 3.68V 0V 0V 4 5 6

2.85V VSIM 2.8V R153 VMEM 0 1.8V VCORE TP165 VT 2.75V VAPP 3 2 1 3.68V
TP172

MC_CLK MC_CMD

VABB 56 VSIM 102

TP170

MC_DAT[0] MC_DAT[1]

93

132 94 AIN3R 7P(CH)

59 AOUT1P AOUT1N

AIN3L

VMEM 98 VMEM 99 VCORE 77 VCORE 73 VVCXO 40 VAPPGATE 44 VAPP 48 VUSB 43 VEXT 4

TP171

MC_DAT[2] MC_DAT[3] LCD_RSP

R248 0

63

106 SPWR 90 91 SPWR AOUT2P

Q103 CPH6311

USB_D+ USB_D-

0V 0V

107 AOUT2P

4 NC
NC

89

AOUT2N

R126 64 AOUT3R 0
76 80 VMIC AIN1P AIN1N AIN2P AIN2N 1 A B C D LIGHT1 LIGHT2 LIGHT3 LGND E F G H J K L 1

VBACK 100

R140 1.2M
IBIAS 111 3 14 15 16 LDOEN 108 TP128 TDO 33 TDI 1 NC NC NC NC

C165 0.1 C164 C163 1 1

60

AOUT3L

VRTC 103

TP166 TP167 VRTC BT_POWER_ON VBACK BS3 TP168 BS4 BS1 BS2 BUFOFF

33 P(CH)

96 79 95

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 10 11 12 13 14 15 16 91 10 11 12

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 37 38 41 42 45 46 49 50 53 54 57 58 61 62 65 66 131 132 133 137 138 139 143 144 145 134 135 136 140 141 142 146 147 148 113 114 115 119 120 121 125 126 127 116 117 118 122 123 124 128 129 130 35 36 39 40 43 44 47 48 51 52 55 56 59 60 63 64 67 68 71 72 75 76 79 80

34 (CH)

68 71 72 75

TMS 17 TCK 18

C166 1

GPI 34

C206 10

105 AOUT2N

IC103 AD6535 ANALOG BASEBAND

VEXT 20

R147 0

VUSB

C118 26 AUXADC1 0.1

9 AUXADC2 REFOUT TEMP1 REFCHG TEMP2 27 25 39 8

RXON 61 TXON 62 ASM 57

R141 100K

SYNTHEN MODESEL3 SYNTHDATA SYNTHCLK

M 69 70 N P R T 73 74 77 78

CSDI 54 CSFS 66

81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 TOP VIEW

CSDO 53 BSDI 50 BSIFS 45 BSDO 42 BSOFS 49 ASDI 41 ASDO 38 ASFS 46

113 AGND0

0.1

114 AGND0 115 AGND0 116 AGND0 117 AGND0 118 AGND0 119 AGND0 120 AGND0 121 AGND0 122 AGND0 123 AGND0 124 AGND0 125 AGND0 126 AGND0 127 AGND0 128 AGND0 129 AGND0 130 AGND0 131 AGND0
132 AGND0 133 AGND0 134 AGND0 135 AGND0 136 AGND0 137 AGND0 138 AGND0 139 AGND0 140 AGND0 141 AGND0 142 AGND0 143 AGND0

ABBRESET 69 MCLKEN 58 MCLK 65

R144 0
13MHZ_CLK_TYPHOON

C151 0.001

INT 37 VCXOEN DBBON(PWRON) 2 87

TCXOEN

TCXOEN

RESET 97

R143 330
REFIN 31 REFBB 10 REFEN 16
144 AGND0 145 AGND0 146 AGND0 147 AGND0 148 AGND0 AGND0 AGND1 AGND2 AGND3 112 AGND4 104 SGND DGND SGND

REFEN 36

C150 1

C155 1

29

32

11

67

88

VBAT

R109 560

R113 560

R176 560

R211 560

70

3.0V VINT 1 Vdd Out 4

TP123

LED112 YPY1105C GREEN

LED117 YPY1105C GREEN

GND Cd

LED109 YPY1105C GREEN

LED120 YPY1105C GREEN

IC108 R3112Q261A VOLTAGE DETECTOR

TCXOOUT

) : Not Mount
7 8 9 10 11 12
Figure 14 SCHEMATIC DIAGRAM (12/22)

5 18

REMOTE_SW

C205 0.01

GX30

CONFIDENTIAL

KEY PWB-B (1/3)

5-23 (5-B)

A
33 KEYPADROW[0] 34 KEYPADCOL[2] 32 KEYPADCOL[1]

FROM SD/SIM FPC PWB-G

11 Genie_TX/USC[0] 10 Genie_TX/USC[5] Genie_RX_USC[3]

5-5 (3-A)

VBACK

FROM CAMERA GROUND FPC PWB-D

JTAGEN RESET

22 SD_DAT1

21 SD_DAT0

13 SD_DAT3

12 SD_DAT2

14 SD_CMD

29 SD_DET

19 SD_CLK

26 SIM_OP

30 SIMRST

31 SIMCLK

23 SD_WP

24 VBACK

R254 7.5K

27 SIMIO

28 VSIM

35 GND

25 GND

20 GND

16 GND

15 GND

VINT

18 VSD

17 VSD

R156 0
R195 0

GND

TDO

TMS

TCK

TDI

CN104

3.0V VINT

3.0V VINT 3.0V VAPP 1

C194 0.1

R198 0

R203 0

R199 0

R202 0 R197 0

R200 0

R220 0

V102 100P R249 20K

R196 0

0.1

3.0V VINT TP125

Vdd Gnd 2

R155 470K

V103 100P

R201 0

TP149

R151 470K

R157 1K

Out

SIMRST

SIMCLK

MC_DAT[1]

MC_DAT[0]

MC_DAT[3]

MC_DAT[2]

SIMIO

MC_CMD

TP150 TP151
JTAGEN USC[3]

MC_CLK

IC107 EW6671 HALL

R182 0

TP152
TDO TMS TCK TDI

C
KEYPADCOL[2] KEYPADROW[0] KEYPADCOL[1]

C216 27P(CH)

C217 12P(CH)

C218 27P(CH)

C193 0.1

D
USC[0] USC[5]

1.8V VCORE

1.8V 2.85V VRTC VSIM

3.0V VINT

3.0V VINT

1.8V 3.0V 3.0V VCORE VUSB VAPP

3.0V VINT

TP158

R170 0

R171 0

R174 0

C179 0.1

C178 0.1 C180 0.1

C184 0.1 C185 0.1 C186 0.1 C190 0.1

C188 0.1 C189 0.1

VCC 120

VCC 160

VSIM 143

VCC 130

VCC 132

VDDUSB 194

VMEM 170

VMEM 173

VMEM 128

VEXT 166

VEXT 110

VMEM 44

VMEM 79

VEXT 66

VEXT 179

VCC 31

VCC 62

VCC 82

VCC 98

VEXT 41

VEXT 68

VDDRTC

VINT

SC[3]

SIMIO SIMCLK SIMRST

R163 0
196 SIMDATAIO 177 SIMCLK

R164 195 GPIO_23 [SIM RESET] 0

197 GPIO_24 [Sound IC RESET] 157 GPIO_47

[IrDA Tx] GPIO_00 126 [IrDA Rx] GPIO_01 124

VMC 30

C208 0.1

C177 0.1

C183 0.1

C187 0.1

C207 R177 0.1 0

C181 R172 0.1 0

R237 0

C191 R175 0.1 0

C182 R173 0.1 0

R279 470K

[USB_CURRENT_CTL] GPIO_02 113 [BT_RTS] GPIO_03 114 [UART CTS of Bluetooth] GPIO_04 112 [SD card detect] GPIO_05 101

US B_C URRENT_CTL BT_RTS BT_CTS

ESET

KEYPADROW[0] KEYPADROW[1] KEYPADROW[2] KEYPADROW[3] KEYPADROW[4]

40 KEYPADROW[0] 54 KEYPADROW[1] 16 KEYPADROW[2] 53 KEYPADROW[3] 15 KEYPADROW[4] 67 KEYPADCOL[0] 14 KEYPADCOL[1]

[LCD controller interrupt] GPIO_06 102 [Headset SW detect from Headset Jack] GPIO_07 89

/LC D_INT

[Stereo / Mono detect of Headset Jack] GPIO_08 100 [MUM of Bluetooth] GPIO_09 [USB detect] GPIO_10 [Flip Switch Detection] GPIO_11 [LCD controller RESET, Sub LCD RESET, Camera Power on] GPIO_12 [Camera Controller Interrupt] GPIO_13 [PCM CLK of Bluetooth] GPIO_14 [PCM DATAIN of Bluetooth] GPIO_15 Boot Control 0 [PCM SYSNC of Bluetooth] GPIO_16 Low USB BOOT (Internal referance clock) Flash BOOT [PCM DATAOUT of Bluetooth] GPIO_17 [UART RXD of Bluetooth] GPIO_33 [UART TXD of Bluetooth] GPIO_34 [SD card WP] GPIO_35 [Modesel2 of Interface IC] GPIO_36 [Typhoon Interrupt] GPIO_37 [Sound IC Interrupt] GPIO_38 [USB pullup control of Interface IC] GPIO_39 90 77 99 78 88 76 69 70 56 55 36 20 18 35 17 34 TP153 USB_PU USB_DET

G
3.0V VINT 3.0V VINT

KEYPADCOL[0] KEYPADCOL[1] KEYPADCOL[2] KEYPADCOL[3] KEYPADCOL[4]

/LCD_RESET

5-23 (5-G)
G

33 KEYPADCOL[2] 32 KEYPADCOL[3] 13 KEYPADCOL[4] High Boot Control 1 High Low 148 USC[0] [Genie TX] 146 USC[1] [RXD] 133 USC[2] [TXD] 145 USC[3] [Genie RX] 134 USC[4] [RTS / Genie RX] USB BOOT (External referance clock) UART BOOT

R188 0

CAM_INT BT_PCMCLK BT_PCMOUT BT_PCMSYNC BT_PCMIN BT_TXD BT_RXD USB_CURREN T_CTL MODESEL2 TP157

BOOTCTRL1

R168 0
G

51 GPIO_55 [Boot Control 1] 12 GPIO_56 [Boot Control 0]

R162 0 BOOTCTRL0
VINT 3.0V

5-23 (5-G)
R291 470K

USC[3]

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 15 SCHEMATIC DIAGRAM (13/22)

5 19

CONFIDENTIAL

GX30

94 1

3.8V VMEM

2.95V 2.83V 2.83V

Q104 EMD6
4 5 6 3 2 1 0V 0V

UN101 INFRARED PORT C196 4.7

7 SGND

6 Gnd 2 5 4

LEDA TXD RXD SD GND Vcc

7 671 L

3.0V VINT

R184 470K

3 2

R183 470K

R185 0

C197 4.7

3.0V VINT

3
R101 0
TP181

CN102
35 GND

ADD[1]

C227 1 R273 47
1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 10 10 10 10
1 8 2 7

34 GND 33 VINT 32 VINT 31 D0 30 D1 29 D2 28 D3 27 D4

FL207 EMI FILTER

9 8 7 6 5 8 7 6 5 8

2 3 4

FL104 NOISE FILTER

DATA[15] DATA[12] DATA[10] DATA[7]

DATA[4]
/CAM_CS CAM_INT

R189 470K

DATA[2] DATA[11] DATA[8]

R274 47

FL206 EMI FILTER

26 D5 25 D6

DATA[6] DATA[0] DATA[5]

23 D8 22 D9 21 D10 20 D11 19 D12 18 D13 17 D14 16 D15 15 RD

R275 47

FL205 7 EMI FILTER

6 5 8 7 6 5

FL102 NOISE FILTER FL103 NOISE FILTER 1

3 4

DATA[3]

DATA[13]

DATA[1] DATA[14]

ADD[1]

2 4

R276 47

FL204 EMI FILTER

14 CAMCS 13 WE 12 CAMINT 11 A1

ADD[2] ADD[19] ADD[18] ADD[17]

1 2 3 4

8 7

10 A2 9 8 /CAM_RESET 7 6 A17 A18 A19 CAMRST GND GND LCDCLK GND GND

10

6 5

FL208 EMI FILTER R272 0

ADD[1-23]

R210 0 R110A 0

5 4 3 2 1

5-17 (2-F)
D_INT HEDSET_DET STERE O_SW BT_POWER_ON G BT_POWER_ON G BT_PCMCLK G BT_PCMSYNC

5-24 (8-A)

5-23 (4-H)
GPIO_09 G

REFOUT G TEMP1 G

TP182

BT_PCMCLK BT_PCMOUT BT_PCMSYNC BT_PCMIN

G BT_PCMOUT G BT_PCMIN

TP183

5-24 (8-B)

CN103
VBAT 35 VBAT

BT_RXD BT_TXD BT_CTS BT_RTS

G BT_RXD G BT_CTS

G BT_TXD G BT_RTS

34 VBAT 33 VBAT

5-24 (8-C)
R218 0

R231 0 R212 0 R219 0 R226 0 R224 0

32 VCORE 31 TEMP 30 REFOUT 29 LIGHT1 28 LED 27 USB_C_CNT 26 BTRESET 25 BUFOFF 24 LCDRSP 23 LCDWAIT

URREN T_CTL BT_RESET G BUFOFF 3.0V VINT LCD_RSP /LCD_WAIT /LCD RESET

5-24 (8-C)

R225 0

L223 FERRITE BEADS R222

) : Not Mount
7 8 9 10 11 12
Figure 16 SCHEMATIC DIAGRAM (14/22)

5 20

FPC PWB-F

FL101 NOISE FILTER

DATA[9]
4 5

5-29 (4 6-H) FROM CAMERA RELAY

24 D7

GX30

CONFIDENTIAL

KEY PWB-B (1/3)

VINT 3.0V

5 23 (5-G)
R291 470K

146 USC[1] [RXD] 133 USC[2] [TXD] 145 USC[3] [Genie RX] 134 USC[4] [RTS / Genie RX] 125 USC[5] [CTS / Genie TX]

[Modesel2 of Interface IC] GPIO_36 [Typhoon Interrupt] GPIO_37 [Sound IC Interrupt] GPIO_38 [USB pullup control of Interface IC] GPIO_39 [Flash VPP] GPO_22 [Sleep of SCRAM2] GPO_23

18 35 17 34 75 42 TP131 TP132 TP133 TP134 TP117 TP135 TP122 TP153

MODESEL2 TP157

USC[3]

USB_PU

JTAGEN TCK TMS TDI TDO

R165 10K

131 USC[6] [GPIO_31 / Genie RX / (RTC monitor)]

178 JTAGEN 122 GPIO_18 [TCK] 198 GPIO_19 [TMS] 158 GPIO_20 [TDI] 199 GPIO_21 [TDO]

[Flash_Memory_1 /CS] NROMCS1 140 [SCRAM1 /CS] NRAMCS1 191 [SCRAM2 /CS] NRAMCS2 154 [Super-AND Flash /CS] [CLE of Super-AND] [LCD Controller /CS] NGPCS1 172 NAUXCS1 192 GPIO_42 141 GPIO_43 193 GPIO_44 155 [SRAM /CS] [Sound_IC /CS] GPIO_45 174 GPIO_46 175 NRD 151 1 A B C D E F G H J 1 19 21 37 43 57 71 79 91 22 23 24 25 26 27 28 29 30 31 32 33 34 35 38 39 44 58 72 80 92 104 116 128 136 150 164 165 45 46 47 48 49 50 51 52 53 54 59 60 61 62 63 64 65 66 67 68 73 74 81 82 93 94 105 106 117 118 129 130 83 84 85 86 95 96 97 98 107 108 109 110 119 120 121 122 75 76 87 88 99 100 111 112 123 124 131 132 40 41 55 69 77 89 101 113 125 133 147 161 166 167 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 10 11 12 13 14 15 16 17 18 91 10 11 12 3 14 15 16 17 18 20 36 42 56 70 78 90 102 114 126 134 148 162 168 184 186 [/UBS] [/LBS] [LCD Controller /Wait] [ALE of Super-AND] NWE 165 NHWR 185 NLWR 187 NWAIT 188 NADV 171 BURSTCLK 190

C_CLK

L106 60 (100MHz)
97 MC_CLK 50 MC_CMD [SD card] [SD card]

/LCD_CS /CAM_CS

[Camera /CS]

C_CMD C_DAT[0] C_DAT[1] C_DAT[2] C_DAT[3] P

10 MC_DAT[0] [SD card] 64 MC_DAT[1] [SD card] 29 MC_DAT[2] [SD card] 85 MC_DAT[3] [SD card] 11 GPIO_22 [LCD RSP]

IC106 AD6529B DIGITAL BASEBAND

TP143 TP136

R180 100
TP110 TP154

176 DPLUS 121 DMINUS

R181 100

[USB D+] [USB D-]

/LCD_WAIT

27 GPO_00 [RXON]

48 GPO_01 [TXON] TP106 200 GPO_02 [WP contorl for Super-AND] 180 GPO_03 [HUM of Bluetooth] G MODESEL1 181 GPO_04 [MODESEL1] 7 TP130 GPO_05 [ASM]

DATA[0] 116 DATA[1] 118 DATA[2] 115 DATA[3] 119 DATA[4] 127 DATA[5] 117 DATA[6] 136 DATA[7] 135 DATA[8] 150 DATA[9] 138 DATA[10] 149 DATA[11] 164 DATA[12] 163 DATA[13] 139 DATA[14] 152 DATA[15] 169 TP155

DATA[0] DATA[1] DATA[2] DATA[3] DATA[4] DATA[5] DATA[6] DATA[7] DATA[8] DATA[9] DATA[10] DATA[11] DATA[12] DATA[13] DATA[14] DATA[15]

K 103 L 115 M 127 N 135 P 149 R 163 T 169 U 185

OWER_ON

5-23 (4-F)

26 GPO_06 [Not use] 182 GPO_07 [power on/off of Bluetotth] 202 GPO_08 [IrDA Power on/off] 203 GPO_09 [BS3]

137 138 139 140 141 142 143 144 145 146 151 152 153 154 155 156 157 158 159 160

FF

204 GPO_10 [BUFOFF] 167 GPO_11 [BS4] 183 GPO_16 [BS1]

170 171 172 173 174 175 176 177 178 179 180 181 182 183

D
ESEL3

184 GPO_17 [BS2] 161 GPO_18 [SYNTHEN] 186 GPO_19 [Modesel3 of Interface IC] 168 GPO_20 [SYNTHDATA] 162 GPO_21 [SYNTHCLK]

V 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 TOP VIEW

[WP control of Flash memory 1] ADD[0] 46 CSDO 96 CSFS 25 CSDI 24 BSDO 3 BSOFS BSDI ADD[1] ADD[2] ADD[3] ADD[4] ADD[5] ADD[6] ADD[7] ADD[8] ADD[9] ADD[10] [Typhoon RESET] ADD[11] ADD[12] ADD[13] ADD[14] ADD[15] ADD[16] ADD[17] ADD[18] 63 PWRON 189 NRESET ADD[19]

21 45 38 60 37 59 74 43 73 58 83 57 72 71 80 94 95 92 93 91

A A TP137 TP138 A A A A TP139 A A A AD TP140 AD AD TP141 AD AD AD AD AD AD AD AD AD AD TP156 AD 13MHZ

23 BSIFS 1 ASDO

19 ASDI 22 ASFS 6 GPO_29

R166 0

47 CLKOUT_GATE 84 CLKOUT 4 GPIO_48 [13MHz Output] [Remote control SW]

142 CLKIN 159 CLKON TP124

13

ADD[20] 106 ADD[21] 104

C173 0.001

49 OSCIN
156 VSSUSB VSSRTC 39 GND 52 GND 61 GND 65 GND 81 GND 86 GND 87 GND 107 GND 109 GND 111 GND 123 GND 129 GND 137 GND 144 GND 147 GND 153 GND 201 GND

ADD[22] 103 ADD[23] 108 [13MHz clock for LCDC and sound IC] GPIO_40 105

R167 20M

28 OSCOUT

R169 0

R179 27

C192 47P(CH)

R174A 10M

G
REMOTE_SW

14

X101 32kHz
C176 2P(CH)

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 17 SCHEMATIC DIAGRAM (15/22)

5 21

CONFIDENTIAL

GX30

BT_RESET

G BUFOFF 3.0V VINT LCD_RSP /LCD_WAIT /LCD_RESET /LCD_INT

5-24 (8-C)

R225 0

R226 0 R224 0

26 BTRESET 25 BUFOFF 24 LCDRSP 23 LCDWAIT 22 LCDRESET 21 LCDINT 20 AGND 19 AGND 18 RECEIVER17 RECEIVER+ 16 AGND 15 AGND

RECIVER_OUTN SCRAM1_/CS

RECIVER_OUTP D_CS M_CS /LCD_CS

R233 0

R235 0
VBAT 3.0V VINT NC

14 LCDCS 13 VBAT 12 VBAT 11 VBAT 10 VINT 9 8 7 VINT GND GND GND GND SPSP+ GND GND

WAIT

5-16 (7,8-B)
DATA[0] DATA[1] DATA[2] DATA[3] DATA[4] DATA[5] DATA[6] DATA[7] DATA[8] DATA[9] DATA[10] DATA[11] DATA[12] DATA[13] DATA[14] DATA[15]

SP1-1 G

SP2-1 G

R228 0

5 4 3

R227 0

2 1

TP184

ADD[1] ADD[2] ADD[3] ADD[4]

TP146

ADD[5] ADD[6]
F-WE# 25 F-RST# 36 WP# 45 OE# 84 F1-CE# 82 F-VPP 46 NC

SF-R/B# 13

SF-WE# 65

SF-WP# 77

26

ALE 54

CLE 44

SF-RE# 24

LB# 55

SF-CE# 78

SC1-CE1# 73

SC2-CE1#/NC(F2-CE#) 38

S-CE1# 85

S/SC1-CE2 40

SC-CE2/NC 28

ADD[8] ADD[9] ADD[10] ADD[11] ADD[12] ADD[13] ADD[14] ADD[15] ADD[16] ADD[17] ADD[18] ADD[19] ADD[20] ADD[21] ADD[22] ADD[23] 13MHZ_CLK

ADD[2] ADD[3] ADD[4] ADD[5] ADD[6] ADD[7] ADD[8] ADD[9] ADD[10] ADD[11] ADD[12] ADD[13] ADD[14] ADD[15] ADD[16] ADD[17] ADD[18] ADD[19] ADD[20] ADD[21] ADD[22] ADD[23]

81 A0 72 A1 71 A2 70 A3 80 A4 79 A5 69 A6 68 A7 15 A8 17 A9 16 A10 3 7 6 5 4 A11 A12 A13 A14 A15

F-RY/BY#

ADD[1]

S/SC-WE# 19

UB# 56

ADD[7]

R258 0

DQ0 61 DQ1 62

DATA[0] DATA[1] DATA[2] DATA[3] DATA[4] DATA[5] DATA[6] DATA[7] DATA[8] DATA[9] DATA[10] DATA[11] DATA[12] DATA[13] DATA[14] DATA[15]

Nor-Flash Signal

Super-AND Flash Signal

SCRAM & SRAM Signal DQ2 51 DQ3 52 DQ4 31 DQ5 32 DQ6 30 DQ7 21 DQ8 60

IC101 LRS1B27 5-LEVEL STACK MEMORY

1 A B C D E F 1 2 3 2 4 3 5 4 6 5 7 6 8 7 8 9

9 10 11 12 10 11

DQ9 59 DQ10 50 DQ11 48 DQ12 39 DQ13 29 DQ14 20 DQ15 18

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

14 A16 67 A17 66 A18 47 A19 2 A20

G 64 65 66 67 68 69 70 71 72 73 74 75 H 76 77 78 79 80 81 82 83 84 85 86 87 SF/F/SC-VCC 34 SF/F/SC-VCC 42 SF/F/SC-VCC 49 S-VCC 41

83 GND 35 GND

C198 0.1

R186 3.0V 0 VINT

C200 0.1

2.8V VBACK

10 NC

11 NC

12 NC

23 NC

43 NC

53 NC

58 NC

63 NC

74 NC

86 NC

NC

NC

NC

NC

NC

NC

NC

NC

TP145

NC

TP142

TP144

) : Not Mount
7 8 9

The numbers 13 , 14 are waveform numbers shown in page 5-3.

10 11 12
Figure 18 SCHEMATIC DIAGRAM (16/22)

5 22

TP147

TP148

NC

87 NC

57 NC

64 NC

33 NC

75 NC

76 NC

22 NC

C199 0.1

37 A22
GND NC

VccIO/NC

NC

R187 0

GRAND FPC PWB-E

27 A21

FPC PWB-F

5-17 (2-B)

G G

5-30 (8 11-A) FROM CAMERA RELAY

L223 FERRITE BEADS R222 0 L221 FERRITE R296 BEADS 470K R234 0

GX30

CONFIDENTIAL

KEY PWB-B (2/3)

A

KEY PWB-B (2/3)

RECEPTION SIGNAL TRANSMISSION SIGNAL SPEAKER SIGNAL

SD/SIM FPC PWB-G

SD CARD CONNECTOR SIM CARD CONNECTOR

BAT100 BACK-UP BATTERY

SW_Side_UP

SW_Side_DOWN

BUCK-UP BATTERY HOLDER

B
KEYPADCOL[1] G KEYPADCOL[2] G KEYPADROW[0] G SW522 TP522 SW501 KEYPADROW[0] POWONKEY TP521

CN104

5-19 (2 5-A)

KEYPADCOL[0-4],KEYPADROW[0-4],POWONKEY G TP506 BATTYPE G TP534 KEYPADROW[1] TP520

5-15 (2-D)

5-15 (5-H)

SW502

SW506

SW510

SW514

SW518

C
SW503 SW507 SW511 SW515 SW519

C504 0.001

TP501 KEYPADROW[2]

BATT G

5-25 (3-A)

SW504

SW508

SW512

SW516

SW520 KEYPADROW[3] TP502

SW505

SW509

SW513

SW517

SW521 KEYPADROW[4]

CN501 BATTERY CONTACT

BATT GND 1 SENSE 2 3 TP527 TP528

TP503 Battery VBAT VBAT G

KEYPADCOL[0]

KEYPADCOL[1]

KEYPADCOL[2]

KEYPADCOL[3]

KEYPADCOL[4]

FS501 2.5A

5-25 (1-B)

C505 22
TP504 TP505 USB_CURRENT_CTL G

5-15 (2-F)
V501 100P V504 100P V505 100P
Battery VBAT

USB_CHG_EN G USB_DET G USB_PU G

5-15 (2-E)
1 GND CE 4 3

VUSB

KEYPADROW0 KEYPADROW1 KEYPADROW2 KEYPADROW3 KEYPADROW4

CENTRE RIGHT UP

Side UP

Side DOWN 0 # 3 6 9

Not

Not

Not Not Not Not

R560 10K R561 120K

MODESEL1 G

RIGHT SOFT SW_Spe Special CAMERA LEFT SOFT

IC508 817A30NB 3.0V REGULATOR

D505 HN2S01FU
6 5 1 2 3 NC

C524 1

KEYPADCOL0 KEYPADCOL1 KEYPADCOL2 KEYPADCOL3 KEYPADCOL4

Ghost

C523 1

VDD VOUT

USB_D+ G G USB_D-

5-15 (2-E)

1 4 7

2 5 8

DOWN LEFT

5-21 (1-C)

NC END/POWER

R564 470K

R503 0
1 2 3 4 5 6 7

F
USC[1] G

IC509 LVC2G34P BUFFER

5-15 (2-E)
4 3

USC[2]

C506 0.1

5-15 (2-E)

USC[5]

G G

VCC

GND

5-15 (2-E)

MODESEL3

R565 470K

R563 0

USC[4] G

C525 0.1
G AUDIO_IN G

5-15 (2-E)

5-17 (3-F)

5-15 (2-E)

USC[6] G BOOTCTRL1 G

AUDIO_OUT G G

5-19 (2-G)

5-19 (1-H)

BOOTCTRL0 3.0V VINT 3 PD PD PS PG 2 1

5-20 (8-G)

GPIO_09 G

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 19 SCHEMATIC DIAGRAM (17/22)

5 23

R559 470K

R562 0

USC[0]

VINT
5 2

R504

5-15 (2-E)

CONFIDENTIAL

GX30

VBAT

IC505 XC620930 REGULATOR

VINT

C512 1

Vss NC 4 NC

3 CE

R527 0
C516 1

R523 470K

5-20 (9-G)

BT_POWER_ON G

R552 100K

IC506 UGNZ2 BLUETOOTH MODULE

6 UARTTX UARTRX 7

C518 0.1

Vin Vout 5

TP514

R550 100K

C522 2.2

10 11 17
VCC VDD18V VCCIO

R516 470K

BT_RXD

BT_TXD G

SPIMOSI 24 SPICLK 25 SPIMISO 31 SPICSB 32 PIO5 20 PIO4 26 PIO8 9 PIO6 21 PIO7 27 PIO2 33 PIO3 22 PIO1 28 PIO0 34

R543 0 R544 0 R545 3.3K

BT_PCMOUT G BT_PCMCLK

G G

12 PCMOUT 18 PCMCLK TP508 13 PCMSYNC 19 PCMIN NC NC 1 2 8 3 USBP USBN UARTCTS UARTRTS 1 2 3 4 5 6

A 1 2 3

C D E

5-20 (9-G)

R515 470K

BT_PCMSYNC G BT_PCMIN

6 12 18 24 30 7 13 19 25 31 8 14 20 26 32 9 15 21 27 33

TP517 TP518 TP519 TP516 TP529 TP530 TP531 TP532 TP533 NC

BT_CTS

4 10 16 22 28 34 5 11 17 23 29

R517 470K

R547 100K

BT_RTS

G NC NC

AN501 BLUETOOTH AERIAL

1 2 3 NC GND Feed point NC 6 NC 5 NC 4 NC NC NC

14 XTALIN 15 XTALOUT
GND GND GND GND

R514 470K

5-20 (10-H)

BT_RESET

16 RESET

RFIO 29 5.0V VBUS_IN

D503 RB160M30
9 PC

BOTTOM VIEW 9 6 3 3 2 1
4 ACL

IC503 TK73840B REGULATOR

PE Vin 3

5 23 30

TP515

1 IN

C507 1

6 GND

5 GND

R507 NC 0

8 5 2 VOUT 7 4 1 Vfb C B A

C510 1

R518 100K

R519 100K

on/off 1

Q505 EC4401 C
3 4 ND ND NS NG 2 1 0V 0V

R540 0
5.2V CHGIN

R542 0

2 3

OUT GND

4 GND 5 GND 6 GND

0.01V 5 Vcc 1 2 4 GND 3 0.01V

R508 2.7K

R511 47K

C511 0.01

ENT_CTL EN

1 0V

R509 18K

3 0V

2 0V

IC507 TC7SET00FU LOGIC

3.0V VINT

R522 10K

2 2.97V 1 0V

R520 47K

Q501 RT1N144 U

CN503 BLUETOOTH AERIAL TERMINAL

Q503 RT1N144 U
3 0V

R504 470K

VUSB

R505 1.5K
G DPU15 26 CPU_USB_D+ 23 GND3 28 PUEA 27 REG33 25 CPU_USB_D- 24 USBD+/RXD 22

R503
1 2 3 4 5 6 7

IC504 USBUF2W6 USB EMI FILTER

1 2 3 6 5 4 TP524 NC TP523

CN502 R528 0 R529 0

TP525 TP535 USB 1 2 3 4 5 6 7 8 9 10 11 GND USB USB D+ USB DUSB VBUS Reserved Synchronisation Clock Manufacturer Specific Reserved GND UART GND UART RXD TXD Not connect (Reserved) RTS Manufacturer Specific CTS GND Hands Free GND UART RXD TXD Not connect (reserve) Audio-OUT Manufacturer Specific Audio-IN GND (Audio)

MODESEL1 MODESEL2 UART_RXD UART_TXD CPUVDD UART_RTS

11 MODESEL3

GND2 21

USBD-/TXD 20 BSYNC/RTS 19 BDATA/CTS 18 NC 17 TXANAN 16

12 TXANAOUT

NC

C508 0.1 C509 0.1

8 UART_CTS

BSYNC

RXANAOUT 15
13 RXANAIN 14 GND1

R501 0

R558 100 R531 100

Power Supply (Power Supply) (Power Supply)

R530 100 R532 100

9 BDATA

10 BCNT

R502 0
6

D504 HN2S01FU
V555 15P V512 15P V513 100P
5 NC 4 2 3 NC

R513 10K

IC502 BU7870KN USB CONTROLLER

3.0V VINT

V514 15P

TP526 TP536

12 13 14

EXTERNAL CONNECTOR
5.2V CHGIN

Q504 EC4301 C
0V 0V 3 4 PD PD PS PG 2 1 2.97V 2.89V

3.0V VINT

TP537

R535 0

R566 270K R536 0

) : Not Mount
7 8 9 10 11 12
Figure 20 SCHEMATIC DIAGRAM (18/22)

5 24

GX30

CONFIDENTIAL

KEY PWB-B (3/3)

A

KEY PWB-B (3/3)

PA

RECEPTION SIGNAL TRANSMISSION SIGNAL

5-17 (2-B)
BATT

5-23 (6-C)

BATT

18
B
5-15 (2-G)
TCXOEN G

IC804 R5322N002B POWER SUPPLY

1 2 CE1 VDD CE2 VOUT1 GND VOUT2 6 5 4 VRF

TP802

TXOUT_

C806 2.2

5-23 (6-D)

R810 1

VBAT

C801 1

VTCXO

R811 C802 2.2 1

C803 0.01

TP801

C807 0.01

TXOU

IP

G G

C812 22P(CH)

QN

4
C832 270P(CH)
C830 1

C811 22P(CH)

24 23 22 21 20 19 18 17 16 15 14 13
TXVCOGB COMMONGND VCCTXVCO IOUT/IIN TXVCOG TXOUTD TXVCODB IOUTB/IINB TXVCOD TXOUTG VCCIO VCCOPLL

L821 2.2nH

L822 2.2nH

QP

C810 1

C851 0.0018

5-17 (2-A,B)

R807 C850 33 0.015

IN

L801 FERRITE BEADS

L809 6.8nH

5
25 26 27

FL904 MATCHING DEVICE

1 NC 2 3 NC 4 5 Out NC GND NC Out GSM850 10 GSM850 GND GSM900 GSM900 9 8 7 6 1 2 3 4

QOUT/QIN QOUTB/QINB VCCIFSYN CPIFSYN LE CLK VCXOOUT SDATA

PLLOUT 12 GSMGND 11 GSMLNAIB 10 GSMLNAI DCSGSMGND 9 8 7 6 5 4 3 2 1

E
5-15 (2-G)
SYNTHEN SYNTHCLK TCXOOUT SYNTHDATA G G G G

C831 R802 0.0022 4.7K

R835 0 R836 0

28 29 30 31 32

5-17 (2-H) 5-15 (2-G)

C833 100P(CH)

IC801 HD155155NP RF

C852 0.5P(CH) L804 2.7nH

DCSLNAIB DCSLNAI PCSDCSGND PCSLNAIB PCSLNAI PCSGND

L803 2.7nH

12
C835 0.1

R837 0

7
1 Vcont GND 2 OUTPUT 4 Vcc 3

NC NC

33 GNDVCXO 34 35 VCXOE VCXOB

VCCRFVCO VCCRFSYN

L805 1.2nH

L806 1.2nH

36 VCCVCXO
VTCXO

VCCLNA
VCCRFLO VCCMIX CAPQB DIVON

VCCBB

FLOCK

CAPIB

CAPQ

CAPI

C834 0.1

C837 0.1

L802 FERRITE BEADS

VRF

BS1 GSM 850 TX RX TX RX TX DCS RX TX PCS RX BS1 G G G G LOW HIGH LOW HIGH HIGH HIGH HIGH LOW

BS2 LOW LOW LOW LOW HIGH LOW HIGH LOW

BS3 HIGH LOW HIGH LOW LOW LOW LOW LOW

BS4 LOW HIGH LOW LOW LOW LOW LOW LOW

GSM 900

C841 0.0033

5-15 (2-G)

BS2 BS3 BS4

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 21 SCHEMATIC DIAGRAM (19/22)

5 25

R806 6.8K

R805 6.8K

C840 330P

C842 0.1

TCX801 26MHz VCTCXO

C836 100P(CH)

37 38 39 40 41 42 43 44 45 46 47 48 49

C844 C843 0.0018 0.0018

GND

5-17 (2-B)

CPRFSYN

AFCDAC

R804 10

C845 0.1

CONFIDENTIAL

GX30

C861A 82P(CH)

R812 15K FL823 FERRITE BEADS

Pin2 GSM 850 GSM 900 DCS LOW LOW HIGH HIGH Pin16 HIGH HIGH HIGH HIGH

C867 47P(CH)

C860

C861 100P(CH)

TXOUT_DCS/PCS

C862 100P(CH)

PCS

C863 47P(CH)

18 17 16 15 14 13 12
Pin_DCS 1800/1900

36 35 34 33 32 31 30
GND GND GND GND GND GND

19 GND 20 GND
1 2 3

21 GND
Pin_GSM 850/900 BS3 BS2

Vdd1 Pout_GSM 850/900 GND

IC802 PF08141B PA MODULE

Vband VddIC GND GND

Vdd2 Pout_DCS 1800/1900 GND

IC805 NL17SZ32XV5T2 LOGIC

Vramp

Vtxb

GND

GND

GND 11 GND 10 GND GND

GND GND GND GND GND GND

9 8

22 GND

1 TXOUT_GSM

2
BS2

23 24 25 26 27 28 29

C865

This Parts is Supplied with Cabinet Parts 104

L871 3.3nH

C864 47P(CH)

C866

C876 1P(CH)
4 5 1 3 10 9 8 7 6 1 2 3 4 GND 2

AERIAL

C854 47P(CH) FL901 SAW FILTER

FL803 RF SWITCH 16
GND

10 11
10 11 12 13 14 15

IN Out1 GSM900 Out2 GND Out1 DCS Out2 GND

5

9 8 7 6

RX_GSM900

GSM900_RX GND

Vc850RX

BS4

GND IN

RX_DCS

FL902 SAW FILTER

BS2

GSM1800/1900-TX VcGSMTx VDD Vc1 ANT

GND

C872 47P(CH)

NC

C855 47P(CH)

GSM850_RX GSM850/900-TX

C874 47P(CH)

10

L872 3.3nH

RX_GSM850

C875 2P(CH)

GSM1800_RX GSM1900_RX Vc2 GND

C873 0.001

ANT801 AERIAL TERMINAL R884 0

1 3 4 2

C871 47P(CH)

C856 22P(CH)

BS1

FL905 ESD DEVICE

1 2 3

C832A 4P(CH)

C870 47P(CH)

5 1 RX_PCS

C881 47P(CH)
C885 1P(CH)

FL903 SAW FILTER

BS3

BS2

) : Not Mount
7 8

The numbers 1 to 12 and 18 are waveform numbers shown in pages 5-2 to 5-4.
9 10 11 12
Figure 22 SCHEMATIC DIAGRAM (20/22)

5 26

BS1

BS4

VRF

C857 22P(CH)

J801 RF CONNECTOR

L834 6.8nH

C831A 1P(CH)

GX30

CONFIDENTIAL
KEY PWB-B (FRONT SIDE)
R212 R219 R226 R224

R222 R218 R235 L221 R231 L223 R234 R225 R233 R227 R228

SOLDER

5-31 (2-H)

D GROUND

FROM

FPC PWB-E

5-31 (3-D)

R185 R184

CN103
TP135 2 10 20 30 36

FROM CAMERA RELAY FPC PWB-F

C197

Q104 C196

15

25

35

TP126

TP127

TP183 TP170 TP184 TP182

LEFT SOFT
C

TP181

TP514

TP113

TP503 TP502

RIGHT SOFT

CENTRE SEND
LED104
R104

TP121

END/ POWER
TP160

TP163

LED103

TP162 TP161

R113

R107 LED107

CAMERA

R106

R103 LED106

R109

TP801 TP802

TP174

TP144

TP179

TP527

TP528

LED112 LED111
TP164 TP165

TP168

TP123

TP147

LED109 R110 LED110

R111

TP177

TP506

TP157

TP178

TP167

TP154

TP155

TP176

TP153

TP521

TP172

TP107

LED120
TP169 TP120 TP119

LED119

R190

R178

LED118

TP173

TP166

TP537

R211

G
TP149 TP125 TP151 TP152 TP103 TP108 TP118 1 TP150 TP515 TP535

L101

L102

D106 C235

ZD101 C101
TP101 TP102

TP524

TP526

C194
3

IC107
2

R176

TP109

LED117

TP124

TP171

TP105

TP104

TP158

MIC100 MICROPHONE

TP180

TP523

TP525

TP536

C193 R182

Figure 23 WIRING SIDE P.W.BOARD (3/5)

5 27

CONFIDENTIAL

GX30

KEY PWB-B (REAR SIDE)

5-31 (4-D)

AN501 BLUETOOTH AERIAL

FROM CAMERA RELAY FPC PWB-F

5-31 (2-E)
SOLDER UN101 INFRARED PORT
FL104 FL103

CN503 BLUETOOTH AERIAL TERMINAL

FROM CAMERA C GROUND FPC PWB-D

C832A

(103-11) AERIAL

CN102
2 10 20 30 34

R884 C831A

FL102

FL101

J801 FL208

R136

MO100 VIBRATOR

M
R517 C518 R552 R527 R210 R547 R189 R550

R135 C522 R110A

FL207

R101 C227 FL206 R274

TP533

L834

15

25

35

R542

TP532

TP531

R514 R273

R296 FL205 R275 R276

ANT801 AERIAL TERMINAL

RF CONNECTOR FL905 FL204 C885

C872 C873 C870 C881

11 8 10 9
L803 L804 L805 L806

TP112

TP111

TP529 TP519 TP517 TP516 TP518

C861

L871 C876 FL901 C854 C875

TP508

FL803 C855 C856

IC109

L113

D105
5

C143 C512

CN501 CONTACT BATTERY

TP505 TP501 TP534 TP520

IC802
FS501

IC505
1 3

FL902 C865 C866

C864 FL823

R192 R191 V124 V101 C105 C104 V109

C142

C516

R245 R246

4 4

TP522

C505

TP504

C867

V104 C139 R523

C504 L105
C110

1 3

5 4

FL904 C860
C810
1 10 15 5 45 48

FL903

C857

R545 R544 R543 R515 R516

IC506

TP530

C861A R812

C863

C862

C874

L872

C871

C103 V106

R112

C852 C845
C844

This Parts is Supplied with Cabinet Parts 104

IC805
IC804
JK101 HANDS FREE CONNECTOR
C807

C850 R807 C851 L809

12 13

18
C843

C801
3

R104A L103
C107

1 3
TP140

ZD104 R244 R132

TP146 TP142 TP141 TP156

C802 R804 C834 C835

L801 C806 6 R811

2 4 5 6 7 12

20

R294 R802 C832 R835 R836 IC108 C833 R837 C837

C198

C200
R268 C219 C222 R295 R293

R179 TP106 R258 R186

C831
R292

R806

IC101
TP132 TP148

C199 R187
TP145 TP143 TP137

C191 C224 R128

C150 R127 C118 C155

R174A R167 R169 C176

C145 R177 C146

TP122

C173 C185 C186 R175 C207 R165 C182 R172 R272 C190 C189 C187
C168 C167

X101

13

C192 R183 R180 R181

TP130

C162 C163

C120 L108

C153 R143 R256

V501 V505

IC106
R153 C160 C159

R122
C108

14
IC508
L106 R168
C524 R562 C215 R563 IC509 R565 Q504 C525 C188 R174 R279 V504 C523

C133 R138
Q101
TP128

R162
TP116

R503

R559 D505

TP114 TP115 1 2 4 3 8

C206 C144

R130

C166
Q103
G

R152 R291

C506
5

1 R564 28 R504

35

IC113

25 20 17 16 15 30 4 5

14

IC504

26
TP136

C507

C508 R502 22Q501

15 21

20

R566
R513

IC105
10 5 9

C509 R501
R507

4 5

C229 R283 R285 3

1

CN104

R158 C152 R139 C149

C157 R146 R278 C226

R145 C154 R142 C148

R151 R156

30

C165 R131 R248 R264 C116A C120A V103 R254 R220

R140

R561 R560

C134

IC103

C147 R124 R126 R277 R115

C115 L107 R137 C132 C121 C113 C122 C127 C117 R129 C126 R262 C116 C112 R263 R125

R147 Q107

R237 R148 R170 C179 TH101 C180 C177 R141 C164 C178 R166 C181 R144 C151 R171 C208 C161

TP131 TP133

R188

R173

C184

C183

C223

TP138

C213

C221

C220

TP117 TP134 TP139

IC111

TP110

IC1141
R266

C205 3
4

2 1

R238 C214 R239 Q106

C228

C841

C803 R810 C811 TCX801C812

L822 L821 C830 C836

25

IC801
40 30 35 36 37

L802 C842 R805

24

C840

R267

C141

R134

C158

C232 R280

10 3 1

IC502 25

IC115
1

D103 R286

5-31 (6-E)

FROM SD/SIM FPC PWB-G

R133 Q108

10

C216 V102 R249 C210 R196 R197 R199 R157

C217 R164 R195 R202 C218 R163 R198 R203 R200 R201 R155 C236

D504
V514 V513 V512 V555

32 1

R505

R281 Q505

D503

C231 R161 R160 C170 R159 C171 C169

R532 R531 R530 R558 R529 R528 R522

Q503

IC503
10 5

R540 R520 R284

R536
1

IC116

R535

CN502 EXTERNAL CONNECTOR

CHARGER CONNECTOR

The numbers 1 to 14 and 18 are waveform numbers shown in pages 5-2 to 5-4.
7 8 9 10 11 12
Figure 24 WIRING SIDE P.W.BOARD (4/5)

5 28

C510 R518 R519

R282 C511 R511 IC507 R509 R508

GX30

CONFIDENTIAL

CAMERA RELAY FPC PWB-F

B

VDD3 CINT WRB CSB EXCKI RDB VDD4 VDD6 VDD2 VDD5 AVDD GND

C
1 2 3 4 5 6 7 8 9 10 11 12

42 41 40 39 38 37 36 35 34 33 32 31

13 14 15 16 17 18 19 20 21 22 23 24

OD8 OD7 OD6 OD5 OD4 OD3 OD2 OD1 OD0 RSTN VDD1 GND

A1 A2 A17 A18 A19 OD15 OD14 OD13 OD12 OD11 OD10 OD9

GND 30 GND 29 GND 28

NC NC NC

CA1001 CAMERA UNIT GND 27 GND 26 GND 25 NC NC NC

4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1

10 9 10 9 10 9 10 9

5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6
Figure 25 SCHEMATIC DIAGRAM (21/22)

5 29

GND GND VINT VINT D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 RD CAMCS WE CAMINT A1 A2 A17 A18 A19 CAMRST

35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 GND 5 GND 4 LCDCLK 3

CN102 5-20 (12-D F)

CONFIDENTIAL

GX30

CN103

5-20 (12-G,H) 5-22 (12-A C)

NC

35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

VBAT VBAT VBAT VCORE TEMP REFOUT LIGHT1 LED USB_C_CNT BTRESET BUFOFF LCDRSP LCDWAIT LCDRESET LCDINT AGND AGND RECEIVERRECEIVER+ AGND AGND LCDCS VBAT VBAT VBAT VINT VINT GND GND GND GND SPSP+ GND GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
A19 7 CAMRST 6 GND 5 GND 4 LCDCLK 3 GND 2 GND 1

VBAT VBAT VBAT TEMP VCORE REFOUT DATA10 LIGHT1 DATA11 LED DATA15 USB_C_CNT DATA14 BTRESET DATA13 LCDRSP DATA12 BUFOFF DATA7 DATA6 DATA5 DATA4 VCCD /RD /WR DATA0 DATA1 DATA2 DATA3 GND GND CAMCLK GND LCDCLK GND +15V -8V VDD6 NC DATA9 DATA8 /LCDWAIT /LCDRESET /LCDINT VINT VINT VBAT VBAT VBAT /LCDCS AGND RECEIVER+ RECEIVERAGND GND GND SPSP+ GND GND

10

11

12

Figure 26 SCHEMATIC DIAGRAM (22/22)

5 30

5-5 (2-C H) CN701 5-7 (2-A,B)

GX30

CONFIDENTIAL

BACK LIGHT FPC PWB-C

CN705
5-14 (8-B)

5-13 (3-G)

CN701

MAIN PWB-A (FRONT SIDE)

TO MAIN PWB-A (REAR SIDE)

B
TO MAIN PWB-A (REAR SIDE)
5-14 (9-G)

CA1001 CAMERA UNIT

SOLDER

MAIN PWB-A E TO (REAR SIDE)

5-14 (12-G)

A
SOLDER

CAMERA RELAY FPC PWB-F

MAIN PWB-A B TO (REAR SIDE)
5-14 (12-G)

C
SOLDER

SD/SIM FPC PWB-G

[SIDE]

TO KEY PWB-B (FRONT SIDE)

5-27 (4-A)

TO KEY PWB-B (REAR SIDE)

5-28 (9-A)

SIM CARD CONNECTOR

CAMERA GROUND FPC PWB-D

CN103

CN102

MEMORY CARD SLOT CONNECTOR

SOLDER

KEY PWB-B C TO (REAR SIDE)

5-28 (11-A)

BACK-UP BATTERY HOLDER

BAT100 BACK-UP BATTERY

CN104
TO KEY PWB-B (REAR SIDE)
5-28 (11-G)

CN704 F

5-14 (8-D)

GROUND FPC PWB-E

TO MAIN PWB-A (REAR SIDE)

LCD001 EXTERNAL DISPLAY

G LCD1000 MAIN DISPLAY

SOLDER

KEY PWB-B D TO (FRONT SIDE)

5-27 (4-A)

5-14 (11-E)

CN703

TO MAIN PWB-A (REAR SIDE)

Figure 27 WIRING SIDE P.W.BOARD (5/5)

5 31

CONFIDENTIAL

GX30

Conditions: SIM card inserted, power on (battery=3.7V), in stand-by mode (opened) Measuring instrument: Digital multimeter : Unmeasurable
IC105 PIN NO. VOLTAGE 1 1.41V 2 0V 3 2.98V 4 2.98V 5 ---------6 0V 7 2.98V 8 0V 9 0V 10 1.13V 11 0.27V 12 ---------13 0V 14 0V 15 3.69V 16 0V 17 0V 18 0V 19 0V 20 0.49V 21 0.7V 22 0.91V 23 0.95V 24 1.01V 25 1.08V 26 0.73V 27 1.36V 28 2.39V 29 2.97V 30 1.79V 31 2.07V 32 2.98V IC111 PIN NO. VOLTAGE 1 ---------2 ---------3 ---------4 ---------5 ---------IC502 PIN NO. VOLTAGE 1 0V 2 0V 3 2.99V 4 2.97V 5 2.99V 6 2.97V 7 ---------8 2.99V 9 0V 10 0V 11 0V 12 0.01V 13 1.31V 14 0V 15 ---------16 ---------17 Not used 18 ---------19 ---------20 ---------21 0V 22 ---------23 ---------24 0.01V 25 0V 26 ---------27 0V 28 0V IC505 PIN NO. VOLTAGE 1 3.69V 2 0V 3 0V 4 Not used 5 ---------IC508 PIN NO. VOLTAGE 1 0V 2 3.69V 3 2.99V 4 3.69V IC801 PIN NO. VOLTAGE 1 2.89V 2 0V 3 0V 4 0V 5 0V 6 0V 7 0V 8 0V 9 0V 10 0V 11 0V 12 0V 13 2.89V 14 2.89V 15 0V 16 0V 17 0V 18 0V 19 0V 20 0V 21 0V 22 2.89V 23 0.21V 24 0.21V 25 0.21V 26 0.21V 27 2.89V 28 0.27V 29 0V 30 0V 31 1.14V 32 0V 33 0V 34 0V 35 1.82V 36 2.89V 37 2.89V 38 0.26V 39 0V 40 2.89V 41 2.89V 42 2.89V 43 2.89V 44 2.87V 45 2.87V 46 2.87V 47 2.87V 48 2.89V 49 0V IC802 PIN NO. VOLTAGE 1 0V 2 0V 3 3.70V 4 0V 5 0V 6 3.70V 7 0V 8 0V 9 0V 10 0V 11 0V 12 2.44V 13 3.70V 14 0V 15 0V 16 0V 17 0V 18 0V 19 0V 20 0V 21 0V 22 0V 23 0V 24 0V 25 0V 26 0V 27 0V 28 0V 29 0V 30 0V 31 0V 32 0V 33 0V 34 0V 35 0V 36 0V

IC113 PIN NO. VOLTAGE 1 0V 2 2.98V 3 0V 4 0V 5 2.98V

IC114 PIN NO. VOLTAGE 1 ---------2 ---------3 ---------4 ---------5 ----------

IC115 PIN NO. VOLTAGE 1 0V 2 0V 3 Not used 4 0V

E
IC107 PIN NO. VOLTAGE 1 2.98V 2 0V 3 2.98V

IC116 PIN NO. VOLTAGE 1 0V 2 0.14V 3 0V 4 0.14V

IC503 PIN NO. VOLTAGE 1 0V 2 0.03V 3 0.03V 4 0V 5 0V 6 0V 7 Not used 8 3.68V 9 2.25V

IC108 PIN NO. VOLTAGE 1 ---------2 ---------3 ---------4 ----------

IC506 PIN NO. VOLTAGE 1 Not used 2 Not used 3 0V 4 0V 5 0V 6 0.01V 7 0V 8 0.01V 9 0V 10 0V 11 0V 12 0.01V 13 0V 14 Not used 15 Not used 16 0V 17 0V 18 0V 19 0V 20 1.87V 21 0V 22 1.8V 23 0V 24 0V 25 0V 26 1.8V 27 0V 28 2.78V 29 0V 30 0V 31 0V 32 1.7V 33 7.75V 34 1.75V

IC509 PIN NO. VOLTAGE 1 2.97V 2 0V 3 2.99V 4 2.97V 5 2.97V 6 2.95V

IC701 PIN NO. VOLTAGE 1 3.69V 2 0V 3 1.81V 4 2.98V 5 2.51V

IC702 PIN NO. VOLTAGE 1 0V 2 0V 3 0V 4 0V 5 3.69V

IC703 PIN NO. VOLTAGE 1 2.96V 2 0V 3 1.81V 4 2.98V 5 1.79V

IC109 PIN NO. VOLTAGE 1 0V 2 0V 3 0V 4 0V 5 3.69V

IC504 PIN NO. VOLTAGE 1 ---------2 0V 3 ---------4 ---------5 Not used 6 ----------

IC507 PIN NO. VOLTAGE 1 0V 2 0V 3 0V 4 0V 5 0V

IC706 PIN NO. VOLTAGE 1 3.58V 2 1.82V 3 0V 4 1.78V 5 3.58V

IC804 PIN NO. VOLTAGE 1 2.96V 2 3.80V 3 2.96V 4 2.89V 5 0V 6 2.89V

IC708 PIN NO. VOLTAGE 1 1.81V 2 0V 3 1.3V 4 2.99V 5 3.69V

IC805 PIN NO. VOLTAGE 1 0V 2 0V 3 0V 4 0V 5 2.89V

NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.

1 2 3 4 5 6

5 32

GX30
MEMO

CONFIDENTIAL

5 33

CONFIDENTIAL
GX30 Phone Service E Market Manual 6. OTHERS CHAPTER [1] Function table of IC
IC101 (LRS1B27): 5-LEVEL STACK MEMORY Pin No. 1* 2 3 4 5 6 7 8 9* 10* 11* 12* 13 14 15 16 17 18 19 20 21 22* 23* 24 25 26* Terminal name NC A20 A11 A15 A14 A13 A12 GND NC NC NC NC SF-RY/BY A16 A8 A10 A9 DQ15 S/SC-/WE DQ14 DQ7 NC NC SF-/RE F-/WE F-RY/-BY Input/Output Input Input Input Input Input Input Output Input Input Input Input Input/Output Input Input/Output Input/Output Input Input Output Description of terminal Not used Address input (NOR Flash, Smartcombo RAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Ground Not used (VCC IO/NC) Not used Not used Not used Ready busy output (Smartcombo Flash) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Write enable input (SRAM, Smartcombo RAM) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Not used Not used Read enable input (Smartcombo Flash) Write enable input (NOR Flash) Ready busy output (NOR Flash) When deleting/writing: VOL When interrupting block delete/write: High-Z (High impedance) Address input (NOR Flash, Smartcombo RAM 2) Sleep state input (Smartcombo RAM 2) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Not used Power (NOR Flash ,Smartcombo Flash , Smartcombo RAM) Ground Reset input (NOR Flash) (F-/RST) When deleting block/writing: VIH When reading: VIH Reset: VIL Address input (NOR Flash) Chip enable input (Smartcombo RAM 2) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Chip enable input (SRAM), sleep state input (Smartcombo RAM 1) Power (SRAM) Power (NOR Flash ,Smartcombo Flash , Smartcombo RAM) Not used Command latch enable input (Smartcombo Flash) Write protect input (NOR Flash)

GX30

27 28 29 30 31 32 33* 34 35 36

A21 SC2-CE2 DQ13 DQ6 DQ4 DQ5 NC SF/F/SC-VCC GND /RST

Input Input Input/Output Input/Output Input/Output Input/Output Input

37 38 39 40 41 42 43* 44 45

A22 SC2-/CE1/NC (F2-/CE) DQ12 S/SC1-CE2 S-VCC SF/F/SC-VCC NC CLE /WP (F-/WP)

Input Input Input/Output Input Input Input

61

GX30
Pin No. 46 Terminal name VPP (F-VPP) Input/Output Input/

CONFIDENTIAL
Description of terminal Power voltage detect terminal (NOR Flash) When deleting/writing: VPP = VPPH When deleting/writing is prohibited: VPP < VPPLK Address input (NOR Flash, Smartcombo RAM) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Power (Flash, Smartcombo RAM) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Not used Address latch enable input (Smartcombo Flash) Byte enable input (DQ0 DQ7) (Smartcombo RAM, SRAM) Byte enable input (DQ8 DQ15) (Smartcombo RAM, SRAM) Not used Not used Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Data input/output (NOR Flash, Smartcombo RAM, SRAM) Command, Address, and Data input/output (Smartcombo Flash) Not used Not used Write enable input (Smartcombo Flash) Address input (NOR Flash, Smartcombo RAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Chip enable input (Smartcombo RAM 1) Not used Not used Not used Write protect input (Smartcombo Flash) Chip enable input (Smartcombo Flash) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Address input (NOR Flash, Smartcombo RAM, SRAM) Chip enable input (NOR Flash) Ground Output enable input (NOR Flash, Smartcombo RAM, SRAM) Chip enable input (SRAM) Not used Not used

47 48 49 50 51 52 53* 54 55 56 57* 58* 59 60 61 62 63* 64* 65 66 67 68 69 70 71 72 73 74* 75* 76* 77 78 79 80 81 82 83 84 85 86* 87*

A19 DQ11 SF/F/SC-VCC DQ10 DQ2 DQ3 NC ALE /LB /UB NC NC DQ9 DQ8 DQ0 DQ1 NC NC SF-/WE A18 A17 A7 A6 A3 A2 A1 SC1-/CE1 NC NC NC SF-/WP SF-/CE A5 A4 A0 F-/CE (F1-/CE) GND /OE S-/CE1 NC NC

Input Input/Output Input/Output Input/Output Input/Output Input Input Input Input/Output Input/Output Input/Output Input/Output Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

62

CONFIDENTIAL
(TOP VIEW)

GX30

1 A B C D E F G H
64 NC 76 NC 1 NC 12 NC

3
2 A20

4
3 A11 15 A8 26 F-RY/-BY 36 /RST 46 VPP 56 /UB 67 A17 79 A5

5
4 A15 16 A10 27 A21 37 A22 47 A19 57 NC 68 A7 80 A4

6
5 A14 17 A9 28 SC2-CE2 38 SC2-/CE1/NC 48 DQ11 58 NC 69 A6 81 A0

7
6 A13 18 DQ15 29 DQ13 39 DQ12 49 SF/F/SC-VCC 59 DQ9 70 A3 82 F-/CE

8
7 A12 19 S/SC-/WE 30 DQ6 40 S/SC1-CE2 50 DQ10 60 DQ8 71 A2 83 GND

9
8 GND 20 DQ14 31 DQ4 41 S-VCC 51 DQ2 61 DQ0 72 A1 84 /OE

10
9 NC 21 DQ7 32 DQ5 42 F/SF/SC-VCC 52 DQ3 62 DQ1 73 SC1-/CE1 85 S-/CE1

11
10 NC 22 NC 33 NC 43 NC 53 NC 63 NC 74 NC 86 NC

12
11 NC 23 NC

13 SF-RY/BY 24 SF-/RE 34 F/SF/SC-VCC 44 CLE 54 ALE 65 SF-/WE 77 SF-/WP

14 A16 25 F-/WE 35 GND 45 /WP 55 /LB 66 A18 78 SF-/CE

75 NC 87 NC

A22 A21 A0~A17 A18~A20 F-/WE,/WP,/RST /OE F-/CE SF-/WE,SF-/WP ALE,CLE,SF-/RE SF-/CE

128M (x16) bit NOR Flash memory

SF/F/SC-VCC VPP F-RY/-BY

128M (x16) bit Smartcombo Flash memory

SF-RY/BY

S/SC-/WE,/LB,/UB SC1-/CE1 S/SC1-CE2

SC1: 32M (x16) bit Smartcombo RAM

DQ0~DQ15

SC2: 64M (x16) bit Smartcombo RAM SC2-/CE1 SC2-CE2 4M (x16) bit SRAM S-/CE1 GND S-VCC

63

GX30
IC103 (AD6535): ANALOG BASEBAND Pin No. 1* 2 3 4* 5 6 7 8 9* 10 11 12 13 14 15 16* 17* 18* 19 20* 21 22 23 24 25 26 27 28 29 30 31 32 33* 34* 35 36* 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52* 53 54 55 56 57 58 59 60 61 62 63 Terminal name TDI VCXOEN VBAT3 VEXT VCHG GATEDRIVE ISENSE TEMP2 AUXADC2 REFBB AGND2 IP IN QN QP RSVD_A16 TMS TCK VBAT3 VEXT CHGOSC BATTYPE CHGDACREF VBATSENSE TEMP1 AUXADC1 REFOUT PA AGND0 AFCDAC REF AGND1 TDO GPI VBAT1 RSVD_C16 INT ASDO REFCHG VVCXO ASDI BSDO VUSB VAPPGATE BSIFS ASFS VUSBIN VAPP BSOFS BSDI VBAT2 NC_G16 CSDO CSDI VBAT2 VABB ASM MCLKEN AOUT1P AOUT3L RXON TXON AOUT1N Input/Output Input Input Input Output Input Output Input Input Input Output Input/Output Input/Output Input/Output Input/Output Input Input Input Output Input Input Output Input Input Input Output Output Output Output Output Input Input Output Output Output Output Input Output Output Output Input Output Input Output Output Input Input Output Input Input Output Input Output Output Output Input Input Output

CONFIDENTIAL
Description of terminal Not used VCXO supply External interface regulator input Not used Charge supply Charge DAC (FET) output control Charge current sense input Temp sensor input for battery Not used Baseband transmit & receive voltage reference Analog baseband ground I-channel positive input/output I-channel negative input/output Q-channel positive input/output Q-channel negative input/outpu Not used Not used Not used External interface regulator input Not used Charge oscillator capacitor Battery type identification input Charge DAC reference Battery voltage sense input Temp sensor input for camera Auxiliary ADC input for temp. sensor adjustment Voltage reference output Power amplifier control output Analog ground Automatic frequency control DAC output Voltage reference Analog ground Not used Not used Voltage controlled crystal oscillator regulator input Not used Digital BB interrupt Audio serial port data output Voltage reference output Voltage controlled crystal oscillator supply 2.71 - 2.79 V (VT) Audio serial port data input Baseband serial port data output USB interface supply 3.0 - 3.6 V Application regulator pass device gate control Baseband serial port input framing signal Audio serial port framing signal USB interface regulator input Application supply 2.75 - 3.3 V Baseband serial port output framing signal Baseband serial port data input Analog baseband regulator input Not used Control serial port data output Control serial port data input Analog baseband regulator input Analog baseband supply Advanced state machine Master clock enable Receiver audio positive output Headset receiver audio L-channel output Baseband receive section control Baseband transmit section control Receiver audio negative output

64

CONFIDENTIAL
Pin No. 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89* 90* 91* 92* 93 94 95 96 97 98 99 100 101 102 103 104 105* 106* 107* 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 Terminal name AOUT3R MCLK CSFS AGND3 LIGHT1 ABBRESET DGND LIGHT2 LIGHT3 VCORE VCOREIN LGND VMIC VCORE VMEMIN AIN2P AIN1P CRST VMEMIN VMEMSEL VBAT5 VBAT4 VRTCIN DBBON SGND AOUT2N SPWR AOUT2P NC_R12 AIN3L AIN3R AIN2N AIN1N RESET VMEM VMEM VBACK VBACKSEL VSIM VRTC SGND AOUT2N SPWR AOUT2P LDOEN KEYOUT KEYON IBIAS AGND4 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 Input/Output Output Input Input Output Input Output Output Output Input Output Output Input Input Input Output Input Input Input Input Input Input Output Input Output Input Input Input Input Output Output Output Output Input Output Output Output Input Output Output Output Input Output Description of terminal Headset receiver audio R-channel output Master clock Control serial port framing signal Analog audio ground Charge LED control Reset input Digital ground USB charge enable Key-pad LED control Digital core supply 1.72 - 1.9 V Digital core regulator input Light driver ground Microphone supply 2.4 - 2.6 V Digital core supply 1.72 - 1.9 V Memory interface regulator input Headset mic audio positive input Mic audio positive input Power-on reset capacitor Memory interface regulator input Memory supply voltage selection Back-up battery regulator input SIM interface regulator input Real-time clock regulator input Digital BB supply regulator on signal AOUT2P/N ground Not used Not used Not used Not used Sound IC audio L-channel input Sound IC audio R-channel input Headset mic audio negative input Mic audio negative input Reset output Memory interface supply 2.75 - 3.05 V Memory interface supply 2.75 - 3.05 V Back-up battery supply 2.72 - 3.05 V Back-up battery supply voltage selection SIM interface supply 2.75 - 2.95 V Real-time clock supply 1.6 - 2.0 V AOUT2P/N ground Not used Not used Not used Regulator enable output Power-on key output Power-on key input Regulator bias current reference Power management analog ground Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply

GX30

65

GX30
Pin No. 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 Terminal name AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 AGND0 Input/Output

CONFIDENTIAL
Description of terminal Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply Thermal ground for power supply

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

66

CONFIDENTIAL
IC105 VHIYMU762C+-1L (YMU762C): SOUND Pin No. 1 2 3 4 5* 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Terminal name CLKI LED /IRQ /RST NC PLLC VDD VSS VREF HPOUT-L/MONO HPOUT-R EQ1 EQ2 EQ3 SPVDD SPVSS SPOUT1 SPOUT2 MTR D7 D6 D5 D4 D3 D2 D1 D0 /WR /CS A0 /RD IOVDD Input/Output Input Output Output Input Output Output Output Output Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input Input Input Input Description of terminal Clock input terminal External LED control terminal Interrupt output terminal Hardware reset input terminal Not used Built-in PLL capacitor terminal Power supply (Typ + 3.0 V) Ground Analog reference voltage terminal Headphone output L-ch Headphone output R-ch Equalizer terminal 1 Equalizer terminal 2 Equalizer terminal 3 Analog power supply for speaker amplifier (Typ + 3.6 V) Analog ground for speaker amplifier Speaker terminal 1 Speaker terminal 2 External motor control terminal CPU I/F data bus 7 CPU I/F data bus 6 CPU I/F data bus 5 CPU I/F data bus 4 CPU I/F data bus 3 CPU I/F data bus 2 CPU I/F data bus 1 CPU I/F data bus 0 CPU I/F write enable CPU I/F chip select input CPU I/F address signal CPU I/F read enable Power supply for terminal

GX30

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
HPOUT-L/ MONO HPOUT-R IOVDD

PLLC

32 /RST 4

CLKI

VDD

VSS

1 PLL Timing Generator

11

10

HP Vol R

HP Vol L

Control register SRAM/ROM

FiFO 64 byte
Intermediate register Interface register

/CS A0 /WR /RD

29 30 28 31

CPU interface

FM + Wave Table Synthesizer

Select Vol R-ch 16-bit DAC Vol L-ch L-ch R-ch

Mono

FiFO 512 byte

EQ Vol

12 EQ1

Sequencer

20 ~ 27 D0~D7

PCM/ADPCM Play back

VREF

13 EQ2

Buffer

+ 14 EQ3 SP Vol

Soft IRQ /IRQ 3 17 SPOUT1 LED 2 MTR 19 NC 5 9

VREF

LED control Vibrator control

TIMER 18 SPOUT2 VREF

16 15
SPVDD SPVSS

Analog power supply for speaker amplifier

67

GX30
IC106 (AD6529B): DIGITAL BASEBAND Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26* 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Terminal name ASDO BSDI BSOFS GPIO_48 VINT GPO_29 GPO_5 VDDRTC VSSRTC MC_DAT[0] GPIO_22 GPIO_56 KEYPADCOL[4] KEYPADCOL[1] KEYPADROW[4] KEYPADROW[2] GPIO_38 GPIO_36 ASDI GPIO_35 ADD[0] ASFS BSIFS BSDO CSDI GPO_6 GPO_0 OSCOUT MC_DAT[2] VMC VCC KEYPADCOL[3] KEYPADCOL[2] GPIO_39 GPIO_37 GPIO_34 ADD[4] ADD[2] GND KEYPADROW[0] VEXT GPO_23 ADD[7] VMEM ADD[1] CSDO CLKOUT_GATE GPO_1 OSCIN MC_CMD GPIO_55 GND KEYPADROW[3] KEYPADROW[1] GPIO_33 GPIO_17 ADD[11] ADD[9] ADD[5] ADD[3] GND VCC PWRON Input/Output Output Input Output Input Input Output Output Input Input/Output Output Input Output Output Input Input Input Output Input Input Output Input Input Output Input Output Output Output Input/Output Input Input Output Output Output Input Output Output Output Input Input Output Output Input Output Output Input Output Input Input/Output Input Input Input Input Output Output Output Output Output Input Output

CONFIDENTIAL
Description of terminal Audio serial port data output to analog BB Baseband serial port data input from analog BB Baseband serial port output framing signal output to analog BB Hook switch of hands free kit (earphone) detection Analog BB interface power supply 1.7 - 3.3 V (VCORE) Analog BB reset output (ABBRESET) Advanced state machine of analog BB RTC power supply 1.0 - 1.9 V (VRTC) RTC ground SD interface data bus 0 RSP for main LCD controller Boot control 2 (Hardware version select) KEYIN signal output 4 KEYIN signal output 1 KEYIN signal input 4 KEYIN signal input 2 Interrupt input from sound generator IC Mode select 2 for interface IC / AOUT3 bias control Audio serial port data input from analog BB SD card interface write protect Write protect control for flash memory 2 Audio serial port framing signal input from analog BB Baseband serial port input framing signal input from analog BB Baseband serial port data output to analog BB Control serial port data input from analog BB Not used Analog baseband receive section control (RXON) 32.768 kHz crystal oscillator output SD interface data bus 2 SD card interface power supply 1.7 - 3.3 V (VAPP) Core power supply 1.7 - 1.9 V (VCORE) KEYIN signal output 3 KEYIN signal output 2 USB PU control for interface IC Interrupt input from analog BB UART_TXD for Bluetooth module Processor address bus 4 Processor address bus 2 Ground KEYIN signal input 0 System interface power supply 2.4 - 3.3 V (VINT) SLEEP control for SRAM 2 Processor address bus 7 Memory power supply 2.7 - 3.3 V (VMEM) Processor address bus 1 Control serial port data output to analog BB Master clock enable from analog BB (MCLKEN) Analog baseband transmit section control (TXON) 32.768 kHz crystal oscillator input SD interface CMD (SD_CMD) Boot control 1 (Hardware version select) Ground KEYIN signal input 3 KEYIN signal input 1 UART_RXD for Bluetooth module PCM data output for Bluetooth module Processor address bus 11 Processor address bus 9 Processor address bus 5 Processor address bus 3 Ground Core power supply 1.7 - 1.9 V (VCORE) System power control for analog BB

68

CONFIDENTIAL
Pin No. 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 Terminal name MC_DAT[1] GND VEXT KEYPADCOL[0] VEXT GPIO_15 GPIO_16 ADD[13] ADD[12] ADD[8] ADD[6] GPO_22 GPIO_14 GPIO_10 GPIO_12 VMEM ADD[14] GND VCC ADD[10] CLKOUT MC_DAT[3] GND GND GPIO_13 GPIO_7 GPIO_9 ADD[19] ADD[17] ADD[18] ADD[15] ADD[16] CSFS MC_CLK VCC GPIO_11 GPIO_8 GPIO_5 GPIO_6 ADD[22] ADD[21] GPIO_40 ADD[20] GND ADD[23] GND VEXT GND GPIO_4 GPIO_2 GPIO_3 DATA[2] DATA[0] DATA[5] DATA[1] DATA[3] VCC DMINUS GPIO_18 GND GPIO_1 USC[5] GPIO_0 DATA[4] Input/Output Input/Output Input Output Input Input Output Output Output Output Output Output Output Input Output Input Output Input Output Output Input/Output Input Input Input Output Output Output Output Output Output Input Input Input Input Input Input Output Output Output Output Output Input Output Output Input Input/Output Input/Output Input/Output Input/Output Input/Output Input Input Output Input Input Output Input/Output Description of terminal SD interface data bus 1 Ground System interface power supply 2.4 - 3.3 V (VINT) KEYIN signal output 0 System interface power supply 2.4 - 3.3 V (VINT) PCM data input for Bluetooth module PCM SYNC output for Bluetooth module Processor address bus 13 Processor address bus 12 Processor address bus 8 Processor address bus 6 VPP control for flash memory 1 PCM clock output for Bluetooth module USB detection Reset output for main LCD controller/Sub LCD driver/Power management IC Memory power supply 2.7 - 3.3 V (VMEM) Processor address bus 14 Ground Core power supply 1.7 - 1.9 V (VCORE) Processor address bus 10 13 MHz clock output for analog BB (CLKOUT) SD interface data bus 3 Ground Ground Interrupt input from camera module Hands free kit (earphone) detection Manufacturer specific input from I/O connector Processor address bus 19 Processor address bus 17 Processor address bus 18 Processor address bus 15 Processor address bus 16 Control serial port framing signal output to analog BB SD interface clock (SD_CLK) Core power supply 1.7 - 1.9 V (VCORE) Flip switch detection Stereo/monaural detection for hands free kit (earphone) SD card detection Interrupt input from main LCD controller Processor address bus 22 Processor address bus 21 13 MHz clock output for main LCD controller & Sound generator IC Processor address bus 20 Ground Processor address bus 23 Ground System interface power supply 2.4 - 3.3 V (VINT) Ground UART_CTS for Bluetooth module USB charge current control UART_RTS for Bluetooth module Processor data bus 2 Processor data bus 0 Processor data bus 5 Processor data bus 1 Processor data bus 3 Core power supply 1.7 - 1.9 V (VCORE) USB DJTAG TCK Ground IrDA receive data USC pin (CTS/Ginie_TX) IrDA transmit data Processor data bus 4

GX30

69

GX30
Pin No. 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190* 191 Terminal name VMEM GND VCC USC[6] VCC USC[2] USC[4] DATA[7] DATA[6] GND DATA[9] DATA[13] NROMCS1 GPIO_42 CLKIN VSIM GND USC[3] USC[1] GND USC[0] DATA[10] DATA[8] NRD DATA[14] GND NRAMCS2 GPIO_44 VSSUSB GPIO_47 GPIO_20 CLKON VCC GPO_18 GPO_21 DATA[12] DATA[11] NWE VEXT GPO_11 GPO_20 DATA[15] VMEM NADV NGPCS1 VMEM GPIO_45 GPIO_46 DPLUS SIMCLK JTAGEN VEXT GPO_3 GPO_4 GPO_7 GPO_16 GPO_17 NHWR/NUSB GPO_19 NLWR/NLSB NWAIT NRESET BURSTCLK NRAMCS1 Input/Output Input Input Input Input Input Input Input/Output Input/Output Input/Output Input/Output Output Output Input Input Input Input Input Input/Output Input/Output Output Input/Output Output Input Output Output Output Input Output Output Input/Output Input/Output Output Input Output Output Input/Output Input Output Output Input Output Output Input Output Input Input Output Output Output Output Output Output Output Output Input Input Output Output

CONFIDENTIAL
Description of terminal Memory power supply 2.7 - 3.3 V (VMEM) Ground Core power supply 1.7 - 1.9 V (VCORE) USC pin (GPIO_31/Ginie_RX) Core power supply 1.7 - 1.9 V (VCORE) USC pin (TXD) USC pin (RTS/Ginie_RX) Processor data bus 7 Processor data bus 6 Ground Processor data bus 9 Processor data bus 13 Chip select for flash memory 1 Chip select for main LCD controller 13 MHz clock input SIM power supply 1.7 - 3.3 V (VSIM) Ground Pull up to VINT USC pin (RXD) Ground USC pin (Ginie_TX) Processor data bus 10 Processor data bus 8 Processor read strobe Processor data bus 14 Ground Chip select for SRAM 2 Wakeup mode select USB ground Camera module reset JTAG TDI 13 MHz oscillator power control signal (VCXOEN) Core power supply 1.7-1.9V (VCORE) SYNTH enable for RF (SYNTHEN) SYNTH clock output for RF (SYNTHCLK) Processor data bus 12 Processor data bus 11 Processor write strobe System interface power supply 2.4 - 3.3 V (VINT) Band select 4 for RF (BS4) SYNTH data output for RF (SYNTHDATA) Processor data bus 15 Memory power supply 2.7 - 3.3 V (VMEM) Address latch enable for flash memory 2 Chip select for flash memory 2 Memory power supply 2.7 - 3.3 V (VMEM) Chip select for 4M SRAM Chip select for sound generator IC USB D+ System interface clock output JTAG enable SIM power supply 2.4 - 3.3 V (VINT) Incoming LED OFF control Mode select 1 for interface IC Bluetooth module power ON/OFF control Band select 1 for RF (BS1) Band select 2 for RF (BS2) Processor high write strobe Mode select 3 for interface IC Processor low write strobe Processor wait input System reset input Not used Chip select for SRAM 1

6 10

CONFIDENTIAL
Pin No. 192 193 194 195 196 197 198 199 200 201 202 203 204 Terminal name NAUXCS1 GPIO_43 VDDUSB GPIO_23 SIMDATAIO GPIO_24 GPIO_19 GPIO_21 GPO_2 GND GPO_8 GPO_9 GPO_10 Input/Output Output Output Input Output Input/Output Output Output Output Output Output Output Output Description of terminal Command latch enable for flash memory 2 Chip select for Camera module USB power supply 2.8 - 3.3 V (VUSB) SIM interface reset SIM interface data input/output Sound generator IC reset JTAG TMS JTAG TDO Write protect control for flash memory 1 Ground IrDA power ON/OFF control Band select 3 for RF (BS3) BUF OFF for main LCD controller

GX30

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

IC107 VHIEW6671++-1R (EW6671): HALL Pin No. 1 2 3 Terminal name VDD GND OUT Input/Output Input Output Description of terminal Input Ground Output

VDD 1 Pulse Regulator

Reg.

Amplifier Hall cell

Output stage

3 OUTPUT 1 2

Schmitt trigger & Latch

2 GND

IC108 VHIR3112Q26-1L (R3112Q261A): VOLTAGE DETECTOR Pin No. 1 2 3 4 Terminal name VDD GND CD OUT Input/Output Input Output Description of terminal Power supply Ground External condenser connection terminal for delay Output terminal (L: when output is detected, H: when output is canceled)

VDD 1 RD

4 OUT

+
VREF

2 GND 3 CD

6 11

GX30
Pin No. 1 2 3 4 5 Terminal name CONT GND NB VOUT VIN Input/Output Input Output Input

CONFIDENTIAL
Description of terminal Control Ground Noise bypass Output Input

IC109 VHINJ287130-1L (NJM2871F03): 3.0 V REGULATOR

VIN 5 Thermal Protection CONT 1

VOUT

NB

Bandgap Reference GND 2

IC111 VHIR116030B-1L (R1160N301B): REGULATOR IC703 VHIR116018B-1L (R116018B): 1.8 V REGULATOR Pin No. 1 2 3 4 5 Terminal name VDD GND CE ECO VOUT Input/Output Input Input Input Output Description of terminal Input Ground Chip enable High speed/low consumption selector switch Output

ECO 4

VDD 1

5 VOUT

+
VREF CURRENT LIMIT CE 3 2 GND

IC113, 706 VHITC7SZ08A-1L (TC7SZ08A): AND GATE/LOGIC Pin No. 1 2 3 4 5 Terminal name A B GND Y VCC Input/Output Input Input Output Input Description of terminal Signal input Signal input Ground Logic value output Power supply

5 VCC (TOP VIEW) A 1 B 2

4 Y

GND 3

6 12

CONFIDENTIAL
IC114 RH-IXA007AFZZL (HA1631S03CME): COMPARATOR Pin No. 1 2 3 4 5 Terminal name IN+ VSS INVOUT VDD Input/Output Input Input Output Description of terminal Input Ground Input Output Power supply

GX30

VDD 5

VOUT 4

1 IN+

2 VSS

3 IN-

IC115 VHIXC61CN27-1L (XC61CN27): REGULATOR Pin No. 1 2 3* 4 Terminal name VOUT VIN NC GND Input/Output Output Input Description of terminal Output Supply voltage input Not used Ground

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

VIN 2

1 VOUT

+ VREF 4 VSS NC 3

IC116 VHIRQ5RW45B-1L (RQ5RW45B): 4.5 V REGULATOR Pin No. 1 2 3 4 Terminal name GND VDD VOUT CE Input/Output Output Input Description of terminal Ground Power supply Output Chip enable

VDD 2

3 VOUT

+ VREF CURRENT LIMIT CE 4 1 GND

6 13

GX30
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17* 18 19 20 21 22 23 24 25 26 27 28 Terminal name MODESEL1 MODESEL2 UART_RXD UART_TXD CPUVDD UART_RTS BSYNC UART_CTS BDATA BCNT MODESEL3 TXANAOUT RXANAIN GND1 RXANAOUT TXANAIN NC BDATA/CTS BSYNC/RTS USBD-/TXD GND2 USBD+/RXD CPU_USB_D+ CPU_USB_DREG33 PU15 PUEA GND3 Input/Output Input Input Output Input Input Input Output Input Input Input Output Input Output Input Input/Output Output Input/Output Input/Output Input/Output Input/Output Output Input

CONFIDENTIAL
Description of terminal Operation mode switching 1 Operation mode switching 2 UART_RXD output UART_TXD input Digital power supply UART_RTS input BSYNC input UART_CTS output BDATA input BDATA input control Operation mode switching 3 Hands free sending external output Hands free receiving external input Ground Hands free receiving output Hands free sending input Not used BDATA/CTS switching external input/output BSYNC/RTS switching external output USBD-/TXD switching external input/output Ground USBD+/RXD switching external input/output CPU_USB_D+ input/output CPU_USB_D- input/output Power supply voltage for USB PMOS open drain output PU15 control input Ground

IC502 VHIBU7870KN-1L (BU7870KN): USB CONTROLLER

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
BSYNC/RTS RXANAOUT
15
MODE 0,1,2: ON MODE 3,5: OFF

USBD-/TXD

BDATA/CTS

21

20

19

18

17
MODE 0,1,2: ON MODE 3,5: OFF

16

USBD+/RXD 22

MODE 0,2,3: OFF MODE 1,5: ON

TXANAIN

GND2

NC

14 GND1

MODE 0,2,3,5: OFF MODE 1: ON CPUVDD

MODE 0,1,3,5: OFF MODE 2: ON

CPU_USB_D+ 23

MODE 0,1,2: OFF MODE 3,5: ON

13 RXANAIN

10K

CPUVDD

CPU_USB_D- 24
MODE 0,1,5: OFF MODE 2,3: ON 10K

CPUVDD

12 TXANAOUT
MODE 0,2,3,5: L MODE 1: H

MODE 0,1,3,5: H MODE 2: L

CPUVDD

MODE 0,1,5: H MODE 2,3: L

REG33 25

MODE 0,1,5: H MODE 2,3: L

11 MODESEL3
CPUVDD

MODE 0,2,3,5: L MODE 1: H

CPUVDD

H: ON L: OFF

MODE 0,1,3,5: H MODE 2: L

CPUVDD

PU15 26

CPUVDD

MODE 0,2,3,5: L MODE 1: H

CPUVDD

10 BCNT

PUEA 27

9 BDATA

GND3 28

DEC CPUVDD

8 UART_CTS

MODESEL1

MODESEL2

UART_RXD

UART_TXD

CPUVDD

UART_RTS

6 14

BSYNC

CONFIDENTIAL
IC505 VHIXC620930-1L (XC620930): REGULATOR Pin No. 1 2 3 4* 5 Terminal name VIN VSS CE NC VOUT Input/Output Input Input Output Description of terminal Input Ground ON/OFF Control Not used Output

GX30

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
1 VIN CE 3 ON/OFF Control Each ciruit Current Limit

5 VOUT

Voltage Reference

2 VSS

IC506 RUNTZA005AFZZL (UGNZ2): BLUETOOTH MODULE Pin No. 1* 2* 3 4 5 6 7 8 9 10 11 12 13 14* 15* 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32* 33 34 Terminal name USBP USBN UART_RTS GND GND UART_TxD UART_RxD UART_CTS PIO8 VCC_IO VCC PCM_OUT PCM_SYNC XTAL_IN XTAL_OUT RESETB VDD18V PCMCLK PCM_IN PIO5 PIO6 PIO3 GND SPIMOSI SPICLK PIO4 PIO7 PIO1 RF_IO GND SPIMISO SPICSB PIO2 PIO0 Input/Output Input/Output Input/Output Output Output Input Input Input/Output Input Input Output Input/Output Input Input Input Output Input/Output Input Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Description of terminal USB DATA+ (Not used) USB DATA- (Not used) UART/Ready to send to DTE Ground Ground UART/TxD to DTE UART/RxD from DTE UART/Clear to send from DTE General purpose I/O Positive supply voltage for IO voltage Connect the VCC, if IO voltage is same as VCC Main supply voltage input 1 Regulated DC source recommended PCM data stream output Connection to PCM frame sync Input/output of 8 kHz Ext clock in (Not used) Ext clock out (Not used) System reset VDD_CORE decupling capacitor Connction to PCM reference Clock input/output of 256 kHz PCM data stream input General purpose I/O General purpose I/O General purpose I/O Ground For factory use only For factory use only General purpose I/O General purpose I/O General purpose I/O RF input/output Ground For factory use only For factory use only (Not used) General purpose I/O General purpose I/O

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

6 15

GX30
IC507 VHITC7SET00FU- (TC7SET00FU): LOGIC Pin No. 1 2 3 4 5 Terminal name INB INA GND OUT Y VCC Input/Output Input Input Output

CONFIDENTIAL
Description of terminal Input B Input A Ground Output Y Power supply

VCC 5

OUT Y 4

(TOP VIEW)

1 IN B

2 IN A

3 GND

IC508 VHI817A30NB-1R (817A30NB): 3.0 V REGULATOR Pin No. 1 2 3 4 Terminal name VSS VIN VOUT NC Input/Output Input Output Description of terminal Ground (GND) Input voltage (VDD) Output voltage Not used (CE)

VIN 2

3 VOUT

+ Reference voltage VSS 1 Short-circuit protection circuit 4 NC

IC509 VHILVC2G34P-1R (LVC2G34P): BUFFER Pin No. 1 2 3 4 5 6 Terminal name 1A GND 2A 2Y VCC 1Y Input/Output Input Input Output Output Description of terminal Input Ground Input Output Power supply Output

1A

1Y

2A

2Y

GND

VCC

6 16

CONFIDENTIAL
IC701 VHIR116025B-1L (R116025B): 2.5V REGULATOR Pin No. 1 2 3 4 5 Terminal name VDD GND CE ECO VOUT Input/Output Input Input Input Output Description of terminal Input Ground Chip enable High speed/low consumption selector switch Output

GX30

ECO 4

VDD 1

5 VOUT

+
VREF CURRENT LIMIT CE 3 2 GND

IC702 VHITK11131C-1R (TK11131C): REGULATOR Pin No. 1 2 3 4 5 Terminal name CONT GND NP VOUT VIN Input/Output Input Input Output Input Description of terminal Control Ground Capacitor (Vref) Output Input

VIN 5

VOUT 4

Control Circuit

Over Heat & Over Current Protection

- + 320K Bandgap Reference

500K

1 CONT

2 GND

3 NP

6 17

GX30
IC704 (LR38863): DISPLAY CONTROLLER Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13* 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41* 42* 43 44 45 46 47 Terminal name DUMMY4 VDDPLL PLLGND PLLDIV0 PLLDIV1 HSD0 HSD1 HSD2 HSWRD HSEN HSCK DUMMY3 PWM1/PORT8 PLLDIV2 VDDCORE GND SUBWR_B GND VDDCORE PWM0/PORT3 SUBCS_B CS_B VDDIO LCDINT GTDIO_B VDDIO SUBDB1 BDATA[5] (B5) BDATA[5] (B4) BDATA[5] (B3) GND TESTI BSHS_B WR_B SUBRS MP4 RESET_B HSD6 BDATA[2] (B2) BDATA[2] (B1) BDATA[2] (B0) EXCS_B1 XOUT VDDIO GND SCANEN RD_B RSP Input/Output Input Input Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Input Input/Output Output Input/Output Input/Output Output Output Input/Output Output Output Output Input Input/Output Input/Output Input/Output Output Input/Output Output Output Output Input/Output Output Input Input/Output Input/Output

CONFIDENTIAL
Description of terminal Dummy 4 PLL Power supply 1.8 V (1.6 V~ 2.0 V) PLL Ground PLL multiply switching signal PLL multiply switching signal Data bus for high-speed serial transfer Data bus for high-speed serial transfer Data bus for high-speed serial transfer Read/Write determination signal for high-speed serial transfer High-speed serial data effective signal High is active Standard clock for high-speed serial transfer (5 to 33 MHz) Dummy 3 PWM output 1 General-purpose PORT output (default) (Not used) PLL multiply switching signal CORE Power supply 1.8 V (1.6 V~ 2.0 V) Logic ground Light signal for External display Logic ground CORE Power supply 1.8 V (1.6 V~ 2.0 V) PWM output 0 General-purpose PORT output (default) Chip select signal for External display Device select signal (Display is active when CS_B is Low) IO Power supply 3.0 V (2.7 V~ 3.3 V) External interrupt signal (Starting varies when interruption occurs.) MPEG4ASIC internal core power-cut signal (Low is active.) IO Power supply 3.0 V (2.7 V~ 3.3 V) Data bus for External display Display panel B output signa Display panel B output signa Display panel B output signa Logic ground Test terminal (Connected to GND normally) External Bit Stream horizontal synchronization signal (Low is active) Host write strobe signal Data determination signal for External display MPEG4ASIC reset control signal (Low is active) Data bus for high-speed serial transfer Display panel B output signal Display panel B output signal Display panel B output signal Chip select output 1 (internal decode output) (Not used) Oscillation circuit output (Not used) IO Power supply 3.0 V (2.7 V~ 3.3 V) Logic ground Full scan effective signal High is active (Connected to GND normally) Host read strobe signal Register selection signal HOST_IF section : RSP = Low...Display access RSP = High...Control access Hyper_Serial section : RSP = Low...Control acces RSP = High...Display access Logic ground Data bus for high-speed serial transfer Data sampling clock (display clock) Vertical synchronization signal Horizontal synchronization signal Chip select output 3 (internal decode output) (Not used) Oscillation circuit input/External clock input signal Clock input for full scan Data bus for External display Master reset (All registers are initialized when Low is activated)

48 49 50 51 52 53* 54 55 56

GND HSD3 DCLK VSYNC HSYNC EXCS_B3 XIN SUBDB6 RESET_B

Input/Output Input/Output Input/Output Input/Output Input/Output Input Input/Output Input

6 18

CONFIDENTIAL
Pin No. 57 58 59 60 61 62* 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91* 92 93 94 95 96 97 98 99 100 101 102* 103* 104 105 106 107 108 109* 110 111 112 113 114 115 116 117 118 Terminal name SUBDB0 SUBDB2 HSD5 DB0 HSD4 EXCS_B2 GDATA[5] (G5) GDATA[4] (G4) GDATA[3] (G3) SUBDB3 SUBDB4 HSD7 DB1 DB2 DB3 DB4 STKCHK VDDCORE GND VDDIO GDATA[2] (G2) SUBDB5 BSCLK SUBCK DB5 VDDIO GND VDDCORE CAMCK GDATA[1] (G1) GDATA[0] (G0) RDATA[5] (R5) RDATA[4] (R4) VDDCORE PWMLCD/PORT4 BSBLK_B DB6 DB7 DB8 DB9 VDDIO RDATA[3] (R3) RDATA[2] (R2) RDATA[1] (R1) RDATA[0] (R0) MP4_P0 EXCS_B0 BSPIXEL7 BSVS_B DB10 DB11 DB12 MP4_PLLCK SUBDB7 GND DA0 BSPIXEL0 DCS_B VDDIO BSPIXEL6 SE_DO/PORT0 DB13 Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Output Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input Output Input/Output Input/Output Output Input/Output Output Output Output Output Output Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Output Output Output Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Input/Output Input/Output Input/Output Input Input/Output Output Input/Output

GX30

Description of terminal Data bus for External display Data bus for External display Data bus for high-speed serial transfer Data bus Data bus for high-speed serial transfer Chip select output 2 (internal decode output) (Not used) Display panel G output signal Display panel G output signal Display panel G output signal Data bus for External display Data bus for External display Data bus for high-speed serial transfer Data bus Data bus Data bus Data bus Setting BS-related output terminal to Hi-z when a stack is installed (Connected to GND normally) CORE Power supply 1.8 V (1.6 V~ 2.0 V) Logic ground IO Power supply 3.0 V (2.7 V~ 3.3 V) Display panel G output signal Data bus for External display External Bit Stream data clock Clock for External display Data bus IO Power supply 3.0 V (2.7 V~ 3.3 V) Logic ground CORE Power supply 1.8 V (1.6 V~ 2.0 V) Clock for camera operation Display panel G output signal Display panel G output signal Display panel R output signal Display panel R output signal CORE Power supply 1.8 V (1.6 V~ 2.0 V) PWM LCD output General-purpose PORT output (default) (Not used) External Bit Stream data effective signal (High is active when transferring the data) Data bus Data bus Data bus Data bus IO Power supply 3.0 V (2.7 V~ 3.3 V) Display panel R output signal Display panel R output signal Display panel R output signal Display panel R output signal MPEG4 control Chip select output 0 (internal decode output) (Not used) External Bit Stream data bus External Bit Stream vertical synchronization signal (Low is active) Data bus Data bus Data bus MPEG4ASIC clock 15.36 MHz/CPU supply XIN clock (Not used) Data bus for External display Logic ground Address input for chip select decode External Bit Stream data bus Chip select input dedicated for chip select decode IO Power supply 3.0 V (2.7 V~ 3.3 V) External Bit Stream data bus Data output for 4-wire serial IF (default) General-purpose PORT output Data bus

6 19

GX30
Pin No. 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134* 135 136 137 138 139 140 141 142 143 144 Terminal name DB14 DB15 WAIT_B SUBFLMIN SUBCKS DA1 BSPIXEL1 BSPIXEL4 GND BSPIXEL5 SE_CK/PORT1 SE_LD2/PORT5 BUFOFF_B VDDIO DUMMY2 SE_LD3/PORT6 VDDIO SUBLPIN BSPIXEL2 BSPIXEL3 VDDCORE SE_DI/PORT7 SE_LD1/PORT2 GND VDDCORE DUMMY1 Input/Output Input/Output Input/Output Output Input Output Input/Output Input/Output Input/Output Input/Output Output Output Input Output Input Input/Output Input/Output Input/Output Output

CONFIDENTIAL
Description of terminal Data bus Data bus External wait signal (Low is active) Driver FLM signal input for External display Clock switching signal for External display Address input for chip select decode External Bit Stream data bus External Bit Stream data bus Logic ground External Bit Stream data bus Control clock for 4-wire serial IF (default) General-purpose PORT output Load signal 2 for 4-wire serial IF General-purpose PORT output (default) Buffer Gated switching signal for I/O through current prevention (High when Host_IF signal is activated) IO Power supply 3.0 V (2.7 V~ 3.3 V) Dummy 2 Load signal 3 for 4-wire serial IF General-purpose PORT output (default) (Not used) IO Power supply 3.0 V (2.7 V~ 3.3 V) Driver LP input External display External Bit Stream data bus External Bit Stream data bus CORE Power supply 1.8 V (1.6 V~ 2.0 V) 4-wire serial input (default) General-purpose PORT output Load signal 1 for 4-wire serial IF (default) General-purpose PORT output Logic ground CORE Power supply 1.8 V (1.6 V~ 2.0 V) Dummy 1Dummy 4

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

6 20

CONFIDENTIAL
SCANEN TESTI

GX30

PO PWM/ PO
4-wire SO/PO

RESET_B

PLLDIV[2:0]

Reset Halt Ctrl

PLL Some MHz to 68 MHz

SE_LD2/PORT5 SE_LD3/PORT6 PWM0/PORT3 PWMLCD/PORT4 PWM1/PORT8

Dividing

PLL Clock Generator

MasterClock (MCLK) VRAM/HOST/HS/BS/ Some MHz to 33 MHz VDIF/VSPetc LCDTimingClock (TCLK) TG/Pallet/LCD IF 5MHz~10MHz /CDE/BS SUBLCDTimingClock SUB (STCK) XIN clock LowSpeedClock (LCLK) 100 kHz~200 kHz PWMClock (PCLK) XIN clock MPEGClock (MPCLK) 15.36MHz or XIN CameraClock (CAMCK) Approx.16.128 MHz
SIO PWM External MPEG4_ASIC External CAMERA_DSP

TEST

FULL Scan

XOUT

Oscillation circuit
Oscillation ON/OFF

SE_DO/PORT0 SE_CK/PORT1 SE_LD1/PORT2 SE_DI/PORT7

XIN/ SCANCK SCANCK

Current consumption is decreased in a standby mode.

Registor
VideoDisplay IF
VDRD ReadDATA
Read Buffer 6 bit x 4

BUFOFF_B DB[15:0] RSP RD_B WR_B CS_B

RAM for mag/dif/sol

WriteDATA
For error diffusion
LINE_Buffer (160 pixels x 36 x 1) Buffer RAM for 1 line

CPU system buffer MCLK system buffer

For magnification function/ 3D data sort function

LINE_Buffer (160 pixels x 48 x 4) Buffer RAM for 1 line Buffer RAM for 1 line Buffer RAM for 1 line Buffer RAM for 1 line

LCD Output Timing Generator LCD I/F

LCD Panel Interface Selector

HOST Interface

SEL

ReadDATA (72bit)

Available for Address Bus magnification Generator Controller function

RACK RACK

DCLK HSYNC

WAIT_B LCDINT

Format conversion circuit

Memory Interface
18 bit x 4 Vertical and horizontal access (No limitation for the start address) Available for mask bit

HSWRD HSEN HSCK HSD[7:0]

Display size 320 x 240 Pixel 260,000 colors

VSYNC

VideoSignalProcessor
Conversion from YUV to RGB (Available for highspeed pipelines)
SEL
Magnify Magnification circuit

WACK WREQ

SEL

DCS_B DA[1:0] EXCS_B[3:0]

ADDRESS DECODE

SEL

Pallet gamma circuit

Diffusion Error diffusion circuit

72

PalletRAM Pallet RAM(R) 8bitx256 RAM(G) RAM(B)

BS circuit

Solidify 3D circuit

Buffer 18bitx4

RW Command function (Transmission)

72bit BS_DATA[71:0]

Buffer 18bitx4

ColorDepthExpand
CDE

Available for 260,000 colors

RAM for BS mag/sol For BS magnification function/ 3D data sort function

LINE_Buffer (160 pixels x 48 x 4) Buffer RAM for 1 line Buffer RAM for 1 line Buffer RAM for 1 line Buffer RAM for 1 line

MaskBit Memory 320x240 Pixcel (2bit)

RED Pallet BLUE Pallet

SEL

R[4:0],B[4:0]

Magnify Solidify Magnification 3D circuit circuit

R[5:0] B[5:0]

Palette I/F

Bit Stream circuit A

BS_CLK
MCLK phase conversion
Buffer control creation UV determination and latch control signal creation Buffer section BUF_ BUF_ DATA0 DATA1
32bit RGBOUT0,2

Available for MPEG4

Display Memory
6bit Green Palette Blue Palette Red Palette

RDATA[5:0]

320x240 Pixcel
6bit

GDATA[5:0]

32bit RGB

Commonly used for sub-LCD VRAM

PIO for MPEG4ASIC control

(18bitx4 =72bit)
17bit

6bit

BDATA[5:0]

Conversion from YUV to RGB

YUVIN0,2

External clock output

Available for sub-LCD 130,000 colors Equivalent to LR38840

STKCHK

H/V effective signal creation

UV determination and latch circuit

MP4RESET_B

Conversion from 8-bit to 16-bit

BSPIXEL[7:0] 5~20MHzmax BSCLK

I/F Timing Control

MP4_PLLCK SUBRS SUBCS_B SUBWR_B GTDIO_B SUBCKS

17

8bit

CPU_DataBus DB[7:0]

4SCAN FRC SUBDB[7:0]

SUBFLMIN

MP4_P0

CAMCK

BSBLK_B

6 21

SUBLPIN

BSHS_B

BSVS_B

SUBCK

GX30
Pin No. 1 2 3 4 5* 6* 7 8 9 10 11 12 13 14* 15 16 17 18 19 20 21 22* 23 24 25 26 27 28 29 30 31 32 33* 34 35 36 37 38 39 40 41 42 43 44 45 46 Terminal name T1 LEDG GND1 VBAT1 LSO11 LSO12 WVOUT T2 TEST LEDR LEDB TRSW CAPP1 CAPN1 SENSP SENSN CAP3 CPIN CAPP2 VIO VPLUS2 CAPN2 GND3 STRB CLK VPLUS12 CAMP DATA FRP IREF VREF LEDCTL ERROUT FLED GND2 SBD VNEG CAMN T4 RSTB BLED SW GNDP VBAT2 VPLUS11 T3 Input/Output Output O, CMOS output O, CMOS output Output I, CMOS input Output Output Output Output Output Input Input Output Input Output Input Output I, CMOS input I, CMOS input Input Output I, CMOS input I, CMOS input Output Output I, CMOS input Output Output Input Input Output I, CMOS input Output Output Output Input Input level VIO VIO VIO VIO VIO VIO

CONFIDENTIAL
ESD Diode Power side GND side GND1 GND1 VBAT1 WVOUT WVOUT VBAT1 VBAT1 VBAT1 WVOUT WVOUT VBAT1 VBAT1 WVOUT CPIN VBAT1 VIO VIO VPLUS12 VIO VIO VBAT1 VBAT1 VIO VBAT2 VBAT2 VBAT1 VBAT1 VIO VBAT2 GND1 GND3 GND3 GND3 GND1 GND1 GND1 GND1 GND1 GND3 GND3 GND1 GND1 GND3 GND3 GND3 GND2 GND1 GND3 GND2 GND2 GND3 GND3 GND2 GND2 GND3 GND3 GND2 GND2 GND2 GND2 GND3 GND2 GND2 GNDP GND2 GND2 GND3 Description of terminal Dummy terminal (internally connected with T2) Green LED drive output terminal (constant current drive) Ground VBAT power supply terminal Level shift output 1 (Not used) Level shift output 1 (Not used) 2/4 times step-up charge pump output Dummy terminal (internally connected with T1) Test terminal (pulldown with IC, inside) Red LED drive output terminal (constant current drive) Blue LED drive output terminal (constant current drive) DC-DC switching Tr drive terminal for R/G/B LED 2/4 times step-up charge pump C1 connection terminal 2/4 times step-up charge pump C1 connection terminal (Not used) DC-DC switching current sense terminal for R/G/B LED DC-DC switching current sense terminal for R/G/B LED 2/4 times step-up charge pump output terminal 2/4 times step-up charge pump input terminal 2/4 times step-up charge pump C2 connection terminal Logic system power supply terminal DC-DC step-up voltage feedback input for R/G/B LED 2/4 times step-up charge pump C2 connection terminal (Not used) Ground Three-wire serial strobe input Three-wire serial clock input DC-DC step-up voltage feedback input for front/rear backlights +15 V voltage output terminal for camera Three-wire serial data input Level shift circuit, rectangular wave input terminal Resistor connection terminal for current reference Voltage reference terminal (connected with C) On/Off control terminal for R/G/B LED SWREG1 error detection amplifier output (Not used) White LED drive terminal for front backlight Ground SBD input terminal Negative power supply terminal for camera 8 V voltage output terminal for camera Dummy terminal (internally connected with T3) Reset input (reset by low input) White LED drive terminal for rear backlight DC-DC coil switching terminal for front/rear backlights Ground VBAT power supply DC-DC step-up voltage feedback input for front/rear backlights Dummy terminal (internally connected with T4) Initial status LED off 0 V output 0 V output Step-up stop LED off LED off Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop Step-up stop 0 V output No output LED off 0 V output LED off Step-up stop Step-up stop

IC707 RH-IXA021AFZZL (BD6015): POWER MANAGEMENT

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

6 22

CONFIDENTIAL
H

GX30

:T3

:VPLUS11 :VBAT2

:GNDP

:SW

:BLED

:RSTB

:T4

:CAMN

:VNEG

:SBD

:GND2

:FLED

:ERROUT

:LEDCTL

:VREF

:IREF

:FRP

:DATA

:CAMP

:VPLUS12

:CLK

:STRB

:GND3

:CAPN2

:VPLUS2

:VIO

:CAPP2

:CPIN

:CAP3

:SENSN

:SENSP

:CAPN1

:CAPP1

:TRSW

:LEDB

:LEDR

:TEST

:T2
8

:WVOUT
7

:LSO12
6

:LSO11
5

:VBAT1
4

:GND1
3

:LEDG
2

:T1
1

IC708 VHITK11130C-1R (TK11130C): REGULATOR Pin No. 1 2 3 4 5 Terminal name VCONT GND NP VOUT VIN Input/Output Input Output Input Description of terminal Control Ground Capacitor (Vref) Output Input

VIN 5

VOUT 4

Control Circuit

Over Heat & Over Current Protection

320K

+ Bandgap Reference

500K

1 VCONT

2 GND

3 NP

6 23

GX30
IC801 VHIHD155155-1L(HD155155NP): RF Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33* 34* 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Terminal name VCCLNA PCSGND PCSLNAI PCSLNAIB PCSDCSGND DCSLNAI DCSLNAIB DCSGSMGND GSMLNAI GSMLNAIB GSMGND PLLOUT VCCOPLL VCCTXVCO GNDTXVCOD GNDTXVCODB TXOUTG COMMONGND TXOUTD TXVCOGB TXVCOG VCCIQ IOUT/IIN IOUTB/IINB QOUT/QIN QOUTB/QIN VCCIFSYN CPIFSYN LE CLK VCXOOUT SDATA GNDVCXO VCXOE VCXOB VCCVCXO VCCRFSYN CPRFSYN FLOCK VCCBB VCCRFVCO DIVON VCCRFLO CAPQB CAPQ CAPIB CAPI VCCMIX GNDLNA Input/Output Input Input Input Input Input Input Input Output Input Output Output Input Input Input Input/Output Input/Output Input/Output Input/Output Input Output Input Input Output Input Input Input Input Output Output Input Input Output Input Output Output Output Output Input

CONFIDENTIAL
Description of terminal VCC for LNA transistor and LNA Bias GND for Emitter of LNA transistor(PCS) Positive input for LNA transistor(PCS) Negative input for LNA transistor(PCS) GND for Emitter of LNA transistor(PCS,DCS) Positive input for LNA transistor(DCS) Negative input for LNA transistor(DCS) GND for Emitter of LNA transistor(DCS,GSM) Positive input for LNA transistor(GSM) Negative input for LNA transistor(GSM) GND for Emitter of LNA transistor(GSM) Current output to control and modulate TXVCO VCC for OPLL and Phase comparator VCC for TXVCO GND for DCS/PCS TxVCO GND for DCS/PCS TxVCO Tx output for GSM GND for common Tx output for DCS/PCS Negative TxVCO output for GSM Positive TxVCO output for GSM VCC for IQ modulator Positive output/input of I channel/modulator Negative output/input of I channel/modulator Positive output/input of Q channel/modulator Negative output/input of Q channel/modulator VCC for IFVCO Buffer and Divider, and IF Synthesiser Charge Pump output of IF Synthesiser Load enable for serial data Clock for serial data Output for VCXO Serial Data GND for VCXO (Not used) Emitter of VCXO transistor (Not used) Base of VCXO transistor VCC for VCXO VCC for RF Synthesiser Charge Pump output of RF Synthesise FLOCK,Output,Fast Lock control for RF Synthesiser VCC for Base band and State Logic VCC for RF VCO VCXOOUT divider control input VCC for RF Local Buffer and Divider Capacitor for Q channel LPF(Negative output) Capacitor for Q channel LPF(Positive output) Capacitor for I channel LPF(Negative output) Capacitor for I channel LPF(Positive output) VCC for Direct conversion Mixer GND for LNA Bias

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

6 24

CONFIDENTIAL
IC802 VHIPF08141B-1L(PF08141B): PA MODULE Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Terminal name Pin_GSM850/900 Vband Vdd IC GND GND Vdd1 Pout_GSM850/900 GND GND GND GND PoutDCS1800/1900 Vdd2 GND GND Vtxb Vramp Pin_DCS1800/1900 GND GND GND GND GND GND GND GND GND GND GND Input/Output Input Input Input Input Output Output Input Input Input Input Description of terminal Input power from TXVCO (GSM850/900) Band select voltage Input,Power supply Ground Ground Power supply Output power (GSM850/900) Ground Ground Ground Ground Output power (DCS/PCS) Power supply Ground Ground Txon Voltage Power control voltage Input power from TXVCO (DCS/PCS) Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground

GX30

Vramp 17

Vtxb 16

Vdd2 13

Pin_DCS/PCS 18

12 Pout_DCS/PCS

control circuit

Pin_GSM

Pout_GSM

2 VBAND

3 Vdd IC

6 Vdd1

6 25

GX30
IC804 VHIR5322N29-1L(R5322N002B): POWER SUPPLY Pin No. 1 2 3 4 5 6 Terminal name CE1 VDD CE2 VOUT2 GND VOUT1 Input/Output Input Input Input Output Output

CONFIDENTIAL
Description of terminal Chip Enable1 Power supply Chip Enable2 VCC for VRF Ground VCC for VTCXO

CE1 1 VDD 2 CE2 3

6 VOUT 5 GND 4 VOUT2

IC805 VHINL17SZ32-1L(NL17SZ32XV5T2): LOGIC Pin No. 1 2 3 4 5 Terminal name VIN1 VIN2 GND VOUT VCC Input/Output Input Input Output Input Description of terminal Input power Input power Ground Logic value output VCC for VRF

Vin1 1 Vin2 2 GND 3

5 Vcc

4 Vout

6 26

CONFIDENTIAL
[2] Function table of Camera
CA1001 DKENDW108AFSN: CAMERA UNIT Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Terminal name A1 A2 A17 A18 A19 OD15 OD14 OD13 OD12 OD11 OD10 OD9 OD8 OD7 OD6 OD5 OD4 OD3 OD2 OD1 OD0 RSTN VDD1 GND GND GND GND GND GND GND GND AVDD VDD5 VDD2 VDD6 VDD4 RDB EXCKI CSB WRB CINT VDD3 Input/Output Input Input Input Input Input Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input Input Input Input Input Output Description of terminal Address signal Address signal Address signal Address signal Address signal Data bus signal 15 Data bus signal 14 Data bus signal 13 Data bus signal 12 Data bus signal 11 Data bus signal 10 Data bus signal 9 Data bus signal 8 Data bus signal 7 Data bus signal 6 Data bus signal 5 Data bus signal 4 Data bus signal 3 Data bus signal 2 Data bus signal 1 Data bus signal 0 Reset signal Power supply input (2.5 V/DSP core) Ground Ground Ground Ground Ground Ground Ground Ground Power supply input (+3.1 V/DSP analog) Power supply input (+2.9 V/For YUV output buffer) Power supply input (+3.1 V/I/O) Power supply input (+3.3 V/V-Driver) Power supply input (8 V/Sensor) IP parameter read signal External clock input Chip select input IP parameter write signal Interruption signal Power supply input (+15 V/Sensor)

GX30

42 1

6 27

GX30

CONFIDENTIAL

[3] Function table of Display

LCD1000 RLCUB0048AF03: MAIN DISPLAY Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43* 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Terminal name T-COM T-COM TFT-COM COMC COMC COMDC VCOMH B0 B1 B2 B3 B4 B5 G0 G1 G2 G3 G4 G5 R0 R1 R2 R3 R4 R5 DCLK HSY VSY SO SI SCLK CS RESET VCC GND GND VDC VDC COM2 VCLAMP VSS2 VSS1 NC VDD2 C5 C5+ C4 C4+ C3 C3+ C2 C2+ C1 C1+ VDC2 VDC2 VR VS VS Input/ Output Input Input Input Output Output Output Output Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Output Input Input Input Input Output Output Output Output Output Output Output Output Output Description of terminal COM electric potential input for CS COM electric potential input for CS COM voltage input COM signal output COM signal output COM center voltage output COM amplitude voltage output Blue data signal (LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal (MSB) Green data signal (LSB) Green data signal Green data signal Green data signal Green data signal Green data signal (MSB) Red data signal (LSB) Red data signal Red data signal Red data signal Red data signal Red data signal (MSB) Data sampling clock Horizontal sync signal Vertical sync signal serial data output serial data input serial clock input serial interface chip select Hardware reset Logic power Ground Ground Analog power Analog power COM control for CS Voltage for CS output DC/DC converter output DC/DC converter output Not used DC/DC converter output Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal Booster capacitor connection terminal DC/DC converter output DC/DC converter output Reference power supply output Source power supply output Source power supply output

MAIN DISPLAY

To Input Terminal
59

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

6 28

CONFIDENTIAL
LCD001 RLCUB0049AFZZ : EXTERNAL DISPLAY Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Terminal name V0 V1 V2 V3 V4 GND RESB CSB RS WRB RDB D0 D1 D2 D3 D4 D5 D6 D7 LP FLM GND (VSS) CK CKS VDD/VEE VREG VOUT CAP1 CAP1+ CAP2 CAP2+ CAP3 CAP3+ Input/Output Input Input Input Input Input Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Input Input Output Output Output Output Output Output Output Output Description of terminal Display drive power supply terminal Display drive power supply terminal Display drive power supply terminal Display drive power supply terminal Display drive power supply terminal Ground Reset signal Chip select signal Register select signal Write signal Read signal Data signal Data signal Data signal Data signal Data signal Data signal Data signal Data signal Latch signal Display sync signal Ground Master clock external input terminal Master clock input selection terminal Logic system power supply terminal Output terminal for generating constant voltage Built-in step-up circuit output terminal Booster capacitor connection terminal () Booster capacitor connection terminal (+) Booster capacitor connection terminal () Booster capacitor connection terminal (+) Booster capacitor connection terminal () Booster capacitor connection terminal (+) Notes 0: Display RAM data 1: Command data L: Activated L: Activated L: Built-in oscillation

GX30

EXTERNAL DISPLAY

33

To Input Terminal

6 29

GX30
MEMO

CONFIDENTIAL

6 30

CONFIDENTIAL

GX30

PARTS GUIDE
No. S5409TQGX30/B

DIGITAL MOBILE PHONE MODEL

GX30

CONTENTS

[1] INTEGRATED CIRCUITS [2] TRANSISTORS [3] DIODES [4] FILTERS [5] COILS

[9] ARRAY PARTS [10] CAPACITORS [11] RESISTORS [12] OTHER CIRCUITRY PARTS [13] CABINET PARTS

[6] VARIABLE RESISTORS [7] VIBRATORS [8] THERMISTOR [14] ACCESSORIES/PACKING PARTS [15] P.W.B. ASSEMBLY

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

GX30
NO. PARTS CODE

CONFIDENTIAL
PRICE NEW PART RANK MARK RANK DESCRIPTION

[1] INTEGRATED CIRCUITS

! ! !

! !

IC101 IC103 IC105 IC106 IC107 IC108 IC109 IC111 IC113 IC114 IC115 IC116 IC502 IC503 IC504 IC505 IC506 IC507 IC508 IC509 IC701 IC702 IC703 IC704 IC706 IC707 IC708 IC801 IC802 IC804 IC805

--------------VHIYMU762C+-1L -------VHIEW6671++-1R VHIR3112Q26-1L VHINJ287130-1L VHIR116030B-1L VHITC7SZ08A-1L RH-IXA007AFZZL VHIXC61CN27-1L VHIRQ5RW45B-1L VHIBU7870KN-1L VHITK73840B-1L VHIUSBUF2W6-1L VHIXC620930-1L RUNTZA005AFZZL VHITC7SET00FUVHI817A30NB-1R VHILVC2G34P-1R VHIR116025B-1L VHITK11131C-1R VHIR116018B-1L -------VHITC7SZ08A-1L RH-IXA021AFZZL VHITK11130C-1R VHIHD155155-1L VHIPF08141B-1L VHIR5322N29-1L VHINL17SZ32-1L

--AX -AD AD AE AE AD AE AD AD AM AF AF AD BC AC AD AD AE AD AE -AD AS AE AV AV AF AC

This Parts is Supplied with Cabinet Parts 104 This Parts is Supplied with Cabinet Parts 104 Sound,YMU762C This Parts is Supplied with Cabinet Parts 104 Hall,EW6671 Voltage Detector,R3112Q261A 3.0V Regulator,NJM2871F03 Regulator,R1160N301B And Gate,TC7SZ08A Comparator,HA1631S03CME Regulator,XC61CN27 4.5V Regulator,RQ5RW45B USB CONTROLLER,BU7870KN Regulator,TK73840B USB EMI Filter,USBUF2W6 Regulator,XC620930 Bluetooth Module,UGNZ2 Logic,TC7SET00FU 3.0V Regulator,817A30NB Buffer,LVC2G34P 2.5V Regulator,R116025B Regulator,TK11131C 1.8V Regulator,R116018B This Parts is Supplied with Cabinet Parts 104 Logic,TC7SZ08A Power Management,BD6015 Regulator,TK11130C RF,HD155155NP PA Module,PF08141B Power Supply,R5322N002B Logic,NL17SZ32XV5T2

[2] TRANSISTORS
Q101 Q103 Q104 Q106 Q107 Q108 Q501 Q503 Q504 Q505 Q702 VS2SK3019//-1+ VSCPH6311++-1R VSEMD6+++++-1R VSEC4301C++-1L VSEC4401C++-1L VSECH8603++-1L VSRT1N144U/-1+ VSRT1N144U/-1+ VSEC4301C++-1L VSEC4401C++-1L VSMCH6413++-1R AC AE AC AB AB AF AB AB AB AB AD FET,2SK3019 FET,CPH6311 Digital,PNP/NPN,EMD6 FET,EC4301 C FET,EC4401 C FET,ECH8603 Digital,NPN,RT1N144 U Digital,NPN,RT1N144 U FET,EC4301 C FET,EC4401 C FET,MCH6413

[3] DIODES
D103 D105 D106 D503 D504 D505 D701 D702 D703 D704 D705 D709 D710 LED103 LED104 LED106 LED107 LED109 LED110 LED111 LED112 LED117 LED118 LED119 LED120 LED702 LED703 LED704 UN101 ZD101 ZD104 VHDRB160M30-1L VHD1SS388//-1+ VHDRB521S30-1VHDRB160M30-1L VHDHN2S01FU-1L VHDHN2S01FU-1L VHDMA2SD32+-1L VHDMA2SD31+-1L VHDRB551V30-1VHDMA2SD31+-1L VHDMA2SD31+-1L VHDRB521S30-1VHD1SS405++-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPYPY1105C-1L VHPGM56271A-1L VHPNECW008A-1L VHPNECW008A-1L VHPGP2W0116-1R VHERSB6R8S+-1L VHERSB6R8S+-1L AC AB AB AC AD AD AB AB AC AB AB AB AC AC AC AC AC AC AC AC AC AC AC AC AC AS AH AH AK AC AC Silicon,RB160M30 Silicon,1SS388 Silicon,RB521S30 Silicon,RB160M30 Silicon,HN2S01FU Silicon,HN2S01FU Silicon,MA2SD32 Silicon,MA2SD31 Silicon,RB551V30 Silicon,MA2SD31 Silicon,MA2SD31 Silicon,RB521S30 Silicon,1SS405 LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Green,YPY1105C LED,Red/Blue/Green,GM56271A LED,White,NECW008A LED,White,NECW008A Infrared Port Zener,6.8V,RSB6.8S Zener,6.8V,RSB6.8S

CONFIDENTIAL
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

GX30

[4] FILTERS
FL101 FL102 FL103 FL104 FL701 FL803 FL823 FL901 FL902 FL903 FL904 FL905 RFILNA004AFZZN RFILNA004AFZZN RFILNA004AFZZN RFILNA004AFZZN RFILNA004AFZZN RFILRA006AFZZL RFILN0020AFZZN RFILRA004AFZZL RFILRA003AFZZL RFILRA005AFZZL RFILRA007AFZZL RFILR0256AFZZL AC AC AC AC AC AF AB AF AH AF AF AE Noise Filter Noise Filter Noise Filter Noise Filter Noise Filter RF Switch Ferrite Beads SAW Filter SAW Filter SAW Filter Matching Device ESD Device

[5] COILS
L101 L102 L103 L105 L106 L107 L108 L113 L221 L223 L701 L702 L714 L715 L746 L749 L801 L802 L803 L804 L805 L806 L809 L821 L822 L834 L871 L872 RCILZ1088YCZZRCILZ1088YCZZRCILZ0315AFZZT RCILZ0315AFZZT RCILZ0370AFZZN RCILZ1088YCZZRCILZ1088YCZZRCILZ1088YCZZRCILZ0387AFZZN RCILZ0387AFZZN RCILC0385AFZZL RCILC0385AFZZL RCILZ0370AFZZN RCILZ0370AFZZN RCILZA008AFZZN RCILZ0387AFZZN RCILZ1103YCZZRCILZA005AFZZN VPCAMT27S0000VPCAMT27S0000VPCAMT12S0000VPCAMT12S0000VPCAMT68J0000VPCAMT22S0000VPCAMT22S0000VPCAMT68J0000VPCAMT33S0000VPCAMT33S0000AC AC AB AB AB AC AC AC AB AB AC AC AB AB AB AB AB AB AC AC AB AB AA AC AC AA AA AA Ferrite Beads Ferrite Beads Ferrite Beads Ferrite Beads 60 ohms (100MHz) Ferrite Beads Ferrite Beads Ferrite Beads Ferrite Beads Ferrite Beads 4.7 H 4.7 H 60 ohms (100MHz) 60 ohms (100MHz) Ferrite Beads Ferrite Beads Ferrite Beads Ferrite Beads 2.7 nH 2.7 nH 1.2 nH 1.2 nH 6.8 nH 2.2 nH 2.2 nH 6.8 nH 3.3 nH 3.3 nH

[6] VARIABLE RESISTORS

V101 V102 V103 V104 V106 V109 V124 V501 V504 V505 V512 V513 V514 V555 VHV10080MBB-1N VHV10080MBB-1N VHV10080MBB-1N VHV10080MAB-1N VHV10080MAB-1N VHV10080MAB-1N VHV10080MAB-1N VHV10080MBB-1N VHV10080MBB-1N VHV10080MBB-1N VHV10270MBB-1N VHV10080MBB-1N VHV10270MBB-1N VHV10270MBB-1N AB AB AB AB AB AB AB AB AB AB AB AB AB AB Varistor,100 pF,8V Varistor,100 pF,8V Varistor,100 pF,8V Varistor,650 pF,8V Varistor,650 pF,8V Varistor,650 pF,8V Varistor,650 pF,8V Varistor,100 pF,8V Varistor,100 pF,8V Varistor,100 pF,8V Varistor,15 pF,27V Varistor,100 pF,8V Varistor,15 pF,27V Varistor,15 pF,27V

[7] VIBRATORS
TCX801 X101 RTCOXA002AFZZL RCRSC0065AFZZL AN AF VCTCXO,26 MHz Crystal,32 kHz

[8] THERMISTOR
TH101 TH701 RH-HXA001AFZZN RH-HXA001AFZZN AF AF Thermistor,10 kohm Thermistor,10 kohm

[9] ARRAY PARTS

FL204 FL205 FL206 FL207 FL208 L709 L710 L711 L733 L734 L735 L736 R273 R274 R275 R276 RFILN0024AFZZR RFILN0024AFZZR RFILN0024AFZZR RFILN0024AFZZR RFILN0024AFZZR RCILZ0376AFZZN RCILZ0376AFZZN RCILZ0376AFZZN RCILZ0376AFZZN RCILZ0376AFZZN RCILZ0376AFZZN RCILZ0376AFZZN RMPTR4470ACZZN RMPTR4470ACZZN RMPTR4470ACZZN RMPTR4470ACZZN AF AF AF AF AF AD AD AD AD AD AD AD AB AB AB AB Array,EMI Filter Array,EMI Filter Array,EMI Filter Array,EMI Filter Array,EMI Filter Array,Ferrite Beads Array,Ferrite Beads Array,Ferrite Beads Array,Ferrite Beads Array,Ferrite Beads Array,Ferrite Beads Array,Ferrite Beads Array,47 ohms Array,47 ohms Array,47 ohms Array,47 ohms

GX30
NO. PARTS CODE

CONFIDENTIAL
PRICE NEW PART RANK MARK RANK DESCRIPTION

[10] CAPACITORS
C101 C103 C104 C105 C107 C108 C110 C112 C113 C115 C116 C116A C117 C118 C120 C120A C121 C122 C126 C127 C132 C133 C134 C139 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 C151 C152 C153 C154 C155 C157 C158 C159 C160 C161 C162 C163 C164 C165 C166 C167 C168 C169 C170 C171 C173 C176 C177 C178 C179 C180 C181 C182 C183 C184 C185 C186 C187 C188 C189 C190 C191 C192 C193 C194 C196 C197 C198 C199 C200 C205 C206 C207 C208 C210 C213 VCCCCZ1EH470JT VCKYCZ1AB104KT VCCCCZ1EH470JT VCKYCZ1AB104KT VCSAPR0GJ226MRC-KZ1315AFZZN VCSAPR0GJ226MVCCCCZ1EH470JT VCKYCZ1EB102KT VCCCCZ1EH470JT VCCCCZ1EH470JT VCKYCZ0JB105KT VCKYCZ1EB102KT VCKYCZ1AB104KT VCCCCZ1EH470JT VCKYCZ0JB105KT VCCCCZ1EH470JT VCCCCZ1EH470JT VCKYCZ1AB104KT VCKYCZ1AB104KT VCCCCZ1EH470JT VCCCCZ1EH470JT VCCCCZ1EH470JT VCKYCZ1AB104KT VCKYCZ1EB472KT VCKYCY1AB105KT VCKYCZ1AB104KT RC-KZ1315AFZZN VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB473KT RC-KZ1308AFZZT VCKYCZ0JB105KT VCKYCZ1EB102KT VCKYCZ1AB104KT VCKYCY1AB104KT VCCCCZ1EH221JT VCKYCZ0JB105KT VCKYCZ1AB473KT VCKYCY0JB225KT VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCY1AB474KT VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCZ1AB104KT VCKYCY1AB105KT RC-KZ1308AFZZT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1EB102KT VCKYCZ1EB102KT VCCCCZ1EH2R0CT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCCCCZ1EH470JT VCKYCZ1AB104KT VCKYCZ1AB104KT RC-KZ1308AFZZT RC-KZ1308AFZZT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1CB103KT RC-KZ1315AFZZN VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ0JB105KT AB AA AB AA AD AC AD AB AB AB AB AB AB AA AB AB AB AB AA AA AB AB AB AA AB AB AA AC AA AA AA AB AD AB AB AA AC AA AB AB AC AB AB AB AC AB AB AA AB AD AA AA AA AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AD AD AA AA AA AB AC AA AA AA AB 47 pF (CH),25V 0.1 F,10V 47 pF (CH),25V 0.1 F,10V 22 F,4V 10 F,6.3V 22 F,4V 47 pF (CH),25V 0.001 F,25V 47 pF (CH),25V 47 pF (CH),25V 1 F,6.3V 0.001 F,25V 0.1 F,10V 47 pF (CH),25V 1 F,6.3V 47 pF (CH),25V 47 pF (CH),25V 0.1 F,10V 0.1 F,10V 47 pF (CH),25V 47 pF (CH),25V 47 pF (CH),25V 0.1 F,10V 0.0047 F,25V 1 F,10V 0.1 F,10V 10 F,6.3V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.047 F,10V 4.7 F,6.3V 1 F,6.3V 0.001 F,25V 0.1 F,10V 0.1 F,10V 220 pF (CH),25V 1 F,6.3V 0.047 F,10V 2.2 F,6.3V 1 F,6.3V 1 F,6.3V 1 F,6.3V 0.47 F,10V 1 F,6.3V 1 F,6.3V 0.1 F,10V 1 F,10V 4.7 F,6.3V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.001 F,25V 0.001 F,25V 2 pF (CH),25V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 47 pF (CH),25V 0.1 F,10V 0.1 F,10V 4.7 F,6.3V 4.7 F,6.3V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.01 F,16V 10 F,6.3V 0.1 F,10V 0.1 F,10V 0.1 F,10V 1 F,6.3V

CONFIDENTIAL
NO. PARTS CODE PRICE NEW PART RANK MARK RANK
1 F,6.3V 0.1 F,10V 27 pF (CH),25V 12 pF (CH),25V 27 pF (CH),25V 0.1 F,10V 0.1 F,10V 0.1 F,10V 0.1 F,10V 1 F,6.3V 0.1 F,10V 0.047 F,10V 1 F,6.3V 2.2 F,6.3V 0.001 F,25V 47 pF (CH),25V 47 pF (CH),25V 1 F,10V 1 F,6.3V 0.001 F,25V 22 F,6.3V 0.1 F,10V 1 F,6.3V 0.1 F,10V 0.1 F,10V 1 F,6.3V 0.01 F,16V 1 F,10V 1 F,10V 0.1 F,10V 2.2 F,25V 1 F,6.3V 1 F,6.3V 0.1 F,10V 4.7 F,6.3V 0.47 F,25V 4.7 F,6.3V 1 F,16V 1 F,6.3V 0.001 F,25V 1 F,16V 2.2 F,25V 2.2 F,6.3V 2.2 F,25V 47 pF (CH),25V 47 pF (CH),25V 2.2 F,25V 4.7 F,6.3V 0.1 F,10V 0.1 F,10V 0.01 F,16V 1 F,6.3V 2.2 F,25V 0.1 F,10V 2.2 F,16V 1 F,6.3V 1 F,6.3V 0.1 F,10V 0.1 F,10V 0.01 F,16V 0.1 F,10V 0.1 F,10V 1 F,16V 1 F,25V 1 F,6.3V 1 F,6.3V 1 F,16V 1 F,16V 1 F,6.3V 1 F,16V 1 F,6.3V 1 F,6.3V 100 pF (CH),25V 0.1 F,10V 0.1 F,16V 1 F,16V 1 F,6.3V 1 F,6.3V 1 F,6.3V 10 pF (CH),50V 10 pF (CH),50V 10 pF (CH),50V 10 pF (CH),50V 0.01 F,16V 1 F,16V

GX30
DESCRIPTION

[10] CAPACITORS
C214 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C226 C227 C228 C229 C231 C232 C235 C236 C504 C505 C506 C507 C508 C509 C510 C511 C512 C516 C518 C522 C523 C524 C525 C701 C702 C703 C704 C705 C706 C707 C708 C709 C710 C711 C712 C713 C714 C718 C719 C721 C722 C724 C725 C726 C728 C729 C732 C734 C736 C737 C739 C740 C741 C742 C743 C744 C745 C746 C747 C748 C750 C751 C752 C753 C754 C755 C756 C757 C758 C759 C760 C761 C766 C769 VCKYCZ0JB105KT VCKYCZ1AB104KT VCCCCZ1EH270JT VCCCCZ1EH120JT VCCCCZ1EH270JT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ0JB105KT VCKYCZ1AB104KT VCKYCZ1AB473KT VCKYCZ0JB105KT VCKYCY0JB225KT VCKYCZ1EB102KT VCCCCZ1EH470JT VCCCCZ1EH470JT VCKYCY1AB105KT VCKYCZ0JB105KT VCKYCZ1EB102KT RC-KZ1321AFZZN VCKYCZ1AB104KT VCKYCZ0JB105KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ0JB105KT VCKYCZ1CB103KT VCKYCY1AB105KT VCKYCY1AB105KT VCKYCZ1AB104KT RC-KZ1319AFZZN VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCZ1AB104KT RC-KZ1308AFZZT VCKYCY1EB474KT RC-KZ1308AFZZT RC-KZ1300AFZZN VCKYCZ0JB105KT VCKYCZ1EB102KT RC-KZ1300AFZZN RC-KZ1319AFZZN VCKYCY0JB225KT RC-KZ1319AFZZN VCCCCZ1EH470JT VCCCCZ1EH470JT RC-KZ1319AFZZN RC-KZ1308AFZZT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1CB103KT VCKYCZ0JB105KT RC-KZ1319AFZZN VCKYCZ1AB104KT RC-KZ1327AFZZN VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCZ1AB104KT VCKYCZ1AB104KT VCKYCZ1CB103KT VCKYCZ1AB104KT VCKYCZ1AB104KT RC-KZ1317AFZZN RC-KZ1314AFZZN VCKYCZ0JB105KT VCKYCZ0JB105KT RC-KZ1317AFZZN RC-KZ1317AFZZN VCKYCZ0JB105KT RC-KZ1317AFZZN VCKYCZ0JB105KT VCKYCZ0JB105KT VCCCCZ1EH101JT VCKYCZ1AB104KT VCKYCY1CB104KT RC-KZ1317AFZZN VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCZ0JB105KT VCCCCZ1HH100DT VCCCCZ1HH100DT VCCCCZ1HH100DT VCCCCZ1HH100DT VCKYCZ1CB103KT VCKYTV1CB105KT AB AA AA AB AA AA AA AA AA AB AA AB AB AC AB AB AB AB AB AB AD AA AB AA AA AB AB AB AB AA AC AB AB AA AD AB AD AC AB AB AC AC AC AC AB AB AC AD AA AA AB AB AC AA AB AB AB AA AA AB AA AA AB AC AB AB AB AB AB AB AB AB AB AA AA AB AB AB AB AA AA AA AA AB AC

GX30
NO. PARTS CODE

CONFIDENTIAL
PRICE NEW PART RANK MARK RANK DESCRIPTION

[10] CAPACITORS
C770 C771 C772 C773 C774 C775 C776 C777 C779 C780 C781 C782 C783 C784 C787 C790 C791 C792 C794 C795 C801 C802 C803 C806 C807 C810 C811 C812 C830 C831 C831A C832 C832A C833 C834 C835 C836 C837 C840 C841 C842 C843 C844 C845 C850 C851 C852 C854 C855 C856 C857 C860 C861 C861A C862 C863 C864 C865 C866 C867 C870 C871 C872 C873 C874 C875 C876 C881 C885 RC-KZ1308AFZZT RC-KZ1317AFZZN VCKYCZ0JB105KT RC-KZ1317AFZZN VCKYCY0JB225KT RC-KZ1308AFZZT VCKYCY1AB105KT VCKYCY1AB105KT RC-KZ1308AFZZT RC-SZ1165AFZZL RC-KZ3021AFZZN VCKYCY0JB225KT RC-KZ1308AFZZT RC-KZ1308AFZZT VCCCCZ1EH101JT VCKYCZ1EB103KT VCKYCZ1EB103KT VCKYCZ1AB104KT VCKYCZ1CB103KT VCKYCZ0JB105KT VCKYCZ0JB105KT VCKYCY0JB225KT VCKYCZ1CB103KT VCKYCY0JB225KT VCKYCZ1CB103KT VCKYCZ0JB105KT VCCCCZ1EH220JT VCCCCZ1EH220JT VCKYCZ0JB105KT RC-KZ3009AFZZN VCCCCZ1EH1R0CT VCCCCZ1EH271JT VCCCCZ1EH4R0CT VCCCCZ1EH101JT VCKYCZ1AB104KT VCKYCZ1AB104KT VCCCCZ1EH101JT VCKYCZ1AB104KT VCKYCZ1EB331KT RC-KZ3010AFZZN VCKYCZ1AB104KT RC-KZ3011AFZZN RC-KZ3011AFZZN VCKYCZ1AB104KT RC-CZ3001AFZZN VCKYCZ1EB182KT VCCCCZ1EH0R5CT VCCCCZ1EH470JT VCCCCZ1EH470JT VCCCCZ1EH220JT VCCCCZ1EH220JT -------VCCCCZ1EH101JT VCCCCZ1EH820JT VCCCCZ1EH101JT VCCCCZ1EH470JT VCCCCZ1EH470JT --------------VCCCCZ1EH470JT VCCCCZ1EH470JT VCCCCZ1EH470JT VCCCCZ1EH470JT VCKYCZ1EB102KT VCCCCZ1EH470JT VCCCCZ1EH2R0CT VCCCCZ1EH1R0CT VCCCCZ1EH470JT VCCCCZ1EH1R0CT AD AB AB AB AC AD AB AB AD AD AC AC AD AD AB AA AA AA AB AB AB AC AB AC AB AB AA AA AB AA AA AA AA AB AA AA AB AA AA AB AA AA AA AA AB AA AB AB AB AA AA -AB AA AB AB AB --AB AB AB AB AB AB AB AA AB AA 4.7 F,6.3V 1 F,16V 1 F,6.3V 1 F,16V 2.2 F,6.3V 4.7 F,6.3V 1 F,10V 1 F,10V 4.7 F,6.3V 4.7 F,10V,Tantalum,Electrolytic 4.7 F,6.3V 2.2 F,6.3V 4.7 F,6.3V 4.7 F,6.3V 100 pF (CH),25V 0.01 F,25V 0.01 F,25V 0.1 F,10V 0.01 F,16V 1 F,6.3V 1 F,6.3V 2.2 F,6.3V 0.01 F,16V 2.2 F,6.3V 0.01 F,16V 1 F,6.3V 22 pF (CH),25V 22 pF (CH),25V 1 F,6.3V 0.0022 F,50V 1 pF (CH),25V 270 pF (CH),25V 4 pF (CH),25V 100 pF (CH),25V 0.1 F,10V 0.1 F,10V 100 pF (CH),25V 0.1 F,10V 330 pF,25V 0.0033 F,50V 0.1 F,10V 0.0018 F,50V 0.0018 F,50V 0.1 F,10V 0.015 F,50V 0.0018 F,25V 0.5 pF (CH),25V 47 pF (CH),25V 47 pF (CH),25V 22 pF (CH),25V 22 pF (CH),25V This Parts is Supplied with Cabinet Parts 104 100 pF (CH),25V 82 pF (CH),25V 100 pF (CH),25V 47 pF (CH),25V 47 pF (CH),25V This Parts is Supplied with Cabinet Parts 104 This Parts is Supplied with Cabinet Parts 104 47 pF (CH),25V 47 pF (CH),25V 47 pF (CH),25V 47 pF (CH),25V 0.001 F,25V 47 pF (CH),25V 2 pF (CH),25V 1 pF (CH),25V 47 pF (CH),25V 1 pF (CH),25V

[11] RESISTORS
R101 R103 R104 R104A R106 R107 R109 R110 R110A R111 R112 R113 R115 R122 VRS-CZ1JB000JT VRS-CZ1JB181JT VRS-CZ1JB561JT VRS-CY1JB000JT VRS-CZ1JB561JT VRS-CZ1JB561JT VRS-CZ1JB561JT VRS-CZ1JB561JT VRS-CZ1JB000JT VRS-CZ1JB561JT VRS-CZ1JB000JT VRS-CZ1JB561JT VRS-CZ1JB101JT VRS-CZ1JB222JT AB AA AA AA AA AA AA AA AB AA AB AA AB AB 0 ohm,Jumper,0.5x1.0mm 180 ohms,1/16W 560 ohms,1/16W 0 ohm,Jumper,0.8x1.55mm,Green 560 ohms,1/16W 560 ohms,1/16W 560 ohms,1/16W 560 ohms,1/16W 0 ohm,Jumper,0.5x1.0mm 560 ohms,1/16W 0 ohm,Jumper,0.5x1.0mm 560 ohms,1/16W 100 ohm,1/16W 2.2 kohms,1/16W

CONFIDENTIAL
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

GX30

[11] RESISTORS
R124 R125 R126 R127 R128 R129 R130 R131 R132 R133 R134 R135 R136 R137 R138 R139 R140 R141 R142 R143 R144 R145 R146 R147 R148 R151 R152 R153 R155 R156 R157 R158 R159 R160 R161 R162 R163 R164 R165 R166 R167 R168 R169 R170 R171 R172 R173 R174 R174A R175 R176 R177 R178 R179 R180 R181 R182 R183 R184 R185 R186 R187 R188 R189 R190 R191 R192 R195 R196 R197 R198 R199 R200 R201 R202 R203 R210 R211 R212 R218 R219 R220 R222 R224 R225 VRS-CZ1JB000JT VRS-CZ1JB222JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB913JT VRS-CZ1JB222JT VRS-CZ1JB222JT VRS-CZ1JB271JT VRS-CZ1JB104FT RR-NZ1103AFZZN VRS-CZ1JB101JT VRS-CY1JB000JT VRS-CY1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CY1JB000JT VRS-CZ1JB125JT VRS-CZ1JB104JT VRS-CZ1JB273JT VRS-CZ1JB331JT VRS-CZ1JB000JT VRS-CZ1JB683JT VRS-CZ1JB183JT VRS-CZ1JB000JT VRS-CZ1JB103DT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CY1JB000JT VRS-CZ1JB102JT VRS-CZ1JB000JT VRS-CZ1JB332JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB103JT VRS-CZ1JB000JT VRS-CZ1JB206JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB106JT VRS-CZ1JB000JT VRS-CZ1JB561JT VRS-CZ1JB000JT VRS-CZ1JB561JT VRS-CZ1JB270JT VRS-CZ1JB101JT VRS-CZ1JB101JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CY1JB000JT VRS-CY1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB561JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB561JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT AB AB AB AB AA AB AB AA AA AC AB AA AA AB AB AA AA AA AA AB AB AA AB AB AB AB AB AB AB AA AA AB AA AB AB AB AB AB AA AB AA AB AB AB AB AB AB AB AA AB AA AB AA AA AB AB AB AB AB AA AA AB AB AB AA AB AB AB AB AB AB AB AB AB AB AB AB AA AB AB AB AB AB AB AB 0 ohm,Jumper,0.5x1.0mm 2.2 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 91 kohms,1/16W 2.2 kohms,1/16W 2.2 kohms,1/16W 270 ohms,1/16W 100 kohm,1/16W 0.18 ohms,1/2W 100 ohm,1/16W 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.8x1.55mm,Green 1.2 Mohms,1/16W 100 kohm,1/16W 27 kohms,1/16W 330 ohms,1/16W 0 ohm,Jumper,0.5x1.0mm 68 kohms,1/16W 18 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 10 kohm,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 0 ohm,Jumper,0.8x1.55mm,Green 1 kohm,1/16W 0 ohm,Jumper,0.5x1.0mm 3.3 kohms,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 10 kohm,1/16W 0 ohm,Jumper,0.5x1.0mm 20 Mohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 10 Mohm,1/16W 0 ohm,Jumper,0.5x1.0mm 560 ohms,1/16W 0 ohm,Jumper,0.5x1.0mm 560 ohms,1/16W 27 ohms,1/16W 100 ohm,1/16W 100 ohm,1/16W 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 560 ohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 560 ohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm

GX30
NO. PARTS CODE

CONFIDENTIAL
PRICE NEW PART RANK MARK RANK DESCRIPTION

[11] RESISTORS
R226 R227 R228 R231 R233 R234 R235 R237 R238 R239 R244 R245 R246 R248 R249 R254 R256 R258 R262 R263 R264 R266 R267 R268 R272 R277 R278 R279 R280 R281 R282 R283 R284 R285 R286 R291 R292 R293 R294 R295 R296 R501 R502 R503 R504 R505 R507 R508 R509 R511 R513 R514 R515 R516 R517 R518 R519 R520 R522 R523 R527 R528 R529 R530 R531 R532 R535 R536 R540 R542 R543 R544 R545 R547 R550 R552 R558 R559 R560 R561 R562 R563 R564 R565 R566 VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB1R0JT VRS-CZ1JB000JT VRS-CZ1JB102JT VRS-CZ1JB102JT VRS-CZ1JB102JT VRS-CZ1JB000JT VRS-CZ1JB203JT VRS-CZ1JB752JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB682JT VRS-CZ1JB682JT VRS-CZ1JB000JT VRS-CZ1JB474DT VRS-CZ1JB683DT VRS-CZ1JB124JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB273JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB182DT VRS-CZ1JB222DT VRS-CZ1JB273JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB154JT VRS-CZ1JB154JT VRS-CZ1JB124JT VRS-CZ1JB124JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB152JT VRS-CZ1JB000JT VRS-CZ1JB272JT VRS-CZ1JB183JT VRS-CZ1JB473JT VRS-CZ1JB103JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB104JT VRS-CZ1JB104JT VRS-CZ1JB473JT VRS-CZ1JB103JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB101JT VRS-CZ1JB101JT VRS-CZ1JB101JT VRS-CY1JB000JT VRS-CY1JB000JT VRS-CY1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB332JT VRS-CZ1JB104JT VRS-CZ1JB104JT VRS-CZ1JB104JT VRS-CZ1JB101JT VRS-CZ1JB474JT VRS-CZ1JB103JT VRS-CZ1JB124JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB474JT VRS-CZ1JB274JT AB AB AB AB AB AB AB AB AA AB AA AA AA AB AA AA AB AB AA AA AB AA AA AB AB AB AA AB AB AB AA AA AA AB AB AB AA AA AB AB AB AB AB AB AB AA AB AA AB AA AA AB AB AB AB AA AA AA AA AB AB AB AB AB AB AB AA AA AA AB AB AB AA AA AA AA AB AB AA AB AB AB AB AB AA 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 1 ohm,1/16W 0 ohm,Jumper,0.5x1.0mm 1 kohm,1/16W 1 kohm,1/16W 1 kohm,1/16W 0 ohm,Jumper,0.5x1.0mm 20 kohms,1/16W 7.5 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 6.8 kohms,1/16W 6.8 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 68 kohms,1/16W 120 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 27 kohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 1.8 kohms,1/16W 2.2 kohms,1/16W 27 kohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 150 kohms,1/16W 150 kohms,1/16W 120 kohms,1/16W 120 kohms,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 1.5 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 2.7 kohms,1/16W 18 kohms,1/16W 47 kohms,1/16W 10 kohm,1/16W 470 kohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 470 kohms,1/16W 100 kohm,1/16W 100 kohm,1/16W 47 kohms,1/16W 10 kohm,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 100 ohm,1/16W 100 ohm,1/16W 100 ohm,1/16W 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.8x1.55mm,Green 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 3.3 kohms,1/16W 100 kohm,1/16W 100 kohm,1/16W 100 kohm,1/16W 100 ohm,1/16W 470 kohms,1/16W 10 kohm,1/16W 120 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 470 kohms,1/16W 270 kohms,1/16W

CONFIDENTIAL
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

GX30

[11] RESISTORS
R701 R703 R704 R704A R705 R705A R707 R708 R712 R713 R714 R716 R717 R718 R720 R723 R727 R728 R729 R730 R732 R737 R738 R740 R741 R743 R744 R745 R747 R748 R750 R756 R758 R760 R761 R802 R804 R805 R806 R807 R810 R811 R812 R835 R836 R837 R884 VRS-CZ1JB332JT VRS-CZ1JB103DT VRS-TV2ABR10JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB124DT VRS-CZ1JB000JT VRS-CZ1JB1R0JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB3R3JT VRS-CZ1JB1R0JT VRS-CZ1JB000JT VRS-CZ1JB104JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB563JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB474JT VRS-CZ1JB000JT VRS-CZ1JB472JT VRS-CZ1JB100JT VRS-CZ1JB682JT VRS-CZ1JB682JT VRS-CZ1JB330JT VRS-CZ1JB1R0JT VRS-CZ1JB1R0JT VRS-CZ1JB153JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT VRS-CZ1JB000JT AA AB AA AB AB AB AB AB AB AA AB AB AB AA AA AB AA AB AB AB AB AB AB AA AB AB AB AB AB AB AB AB AB AB AB AB AA AA AA AA AA AA AA AB AB AB AB 3.3 kohms,1/16W 10 kohm,1/16W 0.1 ohm,1/10W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 120 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 1 ohm,1/16W 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 3.3 ohms,1/16W 1 ohm,1/16W 0 ohm,Jumper,0.5x1.0mm 100 kohm,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 56 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 470 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 4.7 kohms,1/16W 10 ohm,1/16W 6.8 kohms,1/16W 6.8 kohms,1/16W 33 ohms,1/16W 1 ohm,1/16W 1 ohm,1/16W 15 kohms,1/16W 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm 0 ohm,Jumper,0.5x1.0mm

[12] OTHER CIRCUITRY PARTS

AN501 ANT801 BAT100 CA1001 CN102 CN103 CN104 CN501 CN502 CN503 CN701 CN703 CN704 CN705 EP100 FS501 FS701 FS702 J801 JK101 LCD001 LCD100 0 MIC100 MO100 SP100 RANTDA001AFZZL QCNTAA003AFZZN RDNTL0015AFZZ DKENDW108AFSN QCNCWTL35AFZZL QCNCWTL35AFZZL QCNCWUB35AFZZL QCNTAA002AFZZN QCNCW915KAFZZL QCNCW947FAFZZL QCNCMXO60AFZZN QCNCWTV33AFZZL QCNCWUB59AFZZL QCNCW951DAFZZL RPHODA002AFZZ QFS-L252EAFNZN QFS-L631EAFNZN QFS-L132BAFNZN QCNCW927AAFZZR QJAKMA001AFZZL RLCUB0049AFZZ RLCUB0048AFZZ RMICC0213AFZZ RMOTV0557AFZZ RSP-ZA001AFZZ AG AE AG BX AL AL AK AG AM AF AH AK AM AD AK AC AC AC AG AF BD BS AL AM AM Aerial,Bluetooth Terminal,Aerial Battery,Back-up Camera Unit Socket,35Pin Socket,35Pin Socket,35Pin Contact,Battery Connector,External Terminal,Bluetooth Aerial Plug,60Pin Socket,33Pin Socket,59Pin Socket,4Pin Earpiece Fuse,2.5A Fuse,0.63A Fuse,1.25A Connector,RF Hands Free Connector External Display Main Display Microphone Vibrator Speaker

GX30

CONFIDENTIAL
102-3 105 103 102 102-1

[13] CABINET PARTS

109x2 A 124 601x2 103-4 601x2 103-9 103-6 103-8 102-2 123 (SP100) 103-11 103-5 103-2 103-10 C 111 104-25 (PWB-G) 121 (MO100) 116 118 115 119 (BAT100) 104-4 (CA1001) 104-18 (PWB-D) 102-4 104-23 (LCD001) 104-6 104-17 104-1 (PWB-A)

102-5

103-7x2 B 103-3 103-1

104-10 104-20 104-5 104-20

104-14 D 104-26

104-7 104-12 E 104-21x5 104-8 104-15 104-19 (PWB-E) 117 104-2 (PWB-B) 104-21x2 104-16 112 104-13 104-11

104-9 104-24 (PWB-F)

104-3 (PWB-C) 125 122 (EP100)

104-22 (LCD1000)

101-6

101-5 101-12

101-7

101-9

126x2

104 101-4 101-10 113 G 110 101-11 120 (MIC100) 101-11 H 101-2 1 2 3 4 101 114 106x2 601x2 108 101-12 101-8 101-3 107 601x2 101-4 101-1

10

CONFIDENTIAL
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

GX30

[13] CABINET PARTS

101 101 101 101- 1 101- 2 101- 3 101- 4 101- 5 101- 6 101- 7 101- 8 101- 9 101-10 101-11 101-12 102 102 102 102 102 102- 1 102- 2 102- 3 102- 4 102- 5 103 103- 1 103- 2 103- 3 103- 4 103- 5 103- 6 103- 7 103- 8 103- 9 103-10 103-11 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104 104- 1 104- 2 104- 3 104- 4 104- 5 104- 6 104- 7 104- 8 104- 9 104-10 104-11 104-12 104-13 104-14 104-15 104-16 104-17 104-18 104-19 104-20 104-21 104-22 104-23 104-24 104-25 104-26 105 106 DCABAW108AFSM DCABAW108AFSP DCABAW108AFS1 -------GCABC7023AFSA GCOVH1356AFSA MHNG-0210AFSB PCUSSA019AFZZ PCUSS1033AFZZ PMAGZ0072AFZZ PSHEZA026AFZZ PSHEZA049AFZZ PSHEZA166AFZZ PSHEZA175AFZZ TLABZ2783AFZZ DCABBW108AFSP DCABBW108AFSG DCABBW108AFSH DCABBW108AFSM DCABBW108AFS1 -------GCOVH1357AFSA HPNLZ1209AFSA LX-BZA001AFZZ PCUSSA023AFZZ DCABDW108AFS1 -------GCOVH1360AFZZ GFTAB1413AFSA JKNBZ2370AFSA LHLDZ1956AFZZ MSPRC1011AFZZ PCUSSA022AFZZ PFILW0123AFZZ PSHEZA170AFZZ PSHEZA183AFZZ QANTHA001AFSA DKENDW108AFSA DKENDW108AFSB DKENDW108AFSC DKENDW108AFSD DKENDW108AFSE DKENDW108AFSF DKENDW108AFSG DKENDW108AFSH DKENDW108AFSM DKENDW108AFSP DKENDW108AFS1 DKENDW108AFS2 DKENDW108AFS3 DKENDW108AFS4 DKENDW108AFS5 DKENDW108AFS6 DKENDW108AFS7 DKENDW108AFS8 DKENDW108AFS9 --------------CUITKA003AFZZ DKENDW108AFSN LHLDZ1953AF01 LHLDZ1954AF01 LHLDZ1958AFZZ PCUSSA024AFZZ PCUSSA037AFZZ PCUSSA086AFZZ PCUSSA121AFZZ PSHEZA036AFZZ PSHEZA178AFZZ PSLDC3350AFZZ PSLDMA015AFZZ PSLDMA016AFZZL PSLDMA017AFZZL QPWBH0749AFZZ QPWBHA049AFZZ QTANZ9193AFZZL QTANZA001AFZZL RLCUB0048AFZZ RLCUB0049AFZZ RUNTKA014AFZZ RUNTKA016AFZZ TLABZ2595AFZZ GCOVA2546AFSB GCOVA2552AFSJ BE BE BD -AQ AG AG AE AB AD AB AD AC AB AA BA BA BA BA BA -AG AK AA AA AZ -AB AH AC AC AA AA AD AC AB AM CW CW CW CW CW CW CW CW CU CU CW CW CW CW CW CW CW CW CW --AM BX AR AN AH AC AB AB AB AC AB AC AE AE AD AK AH AB AB BS BD BC AX AA AC AC Front Cabinet Assembly [K] Front Cabinet Assembly [U] Front Cabinet Assembly(Except for [K, U]) Front Cabinet (Display) (Not Replacement Item) Front Cabinet (Key) Cover,Hinge (A) Hinge Cushion,Display Cushion,Driver Magnet Sheet,Hinge Cover Leak Mesh Sheet,Hinge Spacer,Hinge Sensor,Moisture Back Cabinet (Display) Assembly [U] Back Cabinet (Display) Assembly [F] Back Cabinet (Display) Assembly [C] Back Cabinet (Display) Assembly [K] Back Cabinet (Display) Assembly(Except for [F, C, K, U]) Back Cabinet (Display) (Not Replacement Item) Cover,Hinge (B) Panel,Camera Screw (1.7x3.5) Cushion,Board Back Cabinet (Key) Assembly Back Cabinet (Key) (Not Replacement Item) Cover,Aerial Cover,SD Card Knob,Battery Cover Belt,SD Card Cover Spring,Battery Lock Cushion,Battery Filter,Infrared Port Spacer,Infrared Port Tape,Infrared Port Aerial Board Unit [W] Board Unit [B] Board Unit [Z] Board Unit [D] Board Unit [Q] Board Unit [L] Board Unit [F] Board Unit [C] Board Unit [K] Board Unit [U] Board Unit [E] Board Unit [G] Board Unit [A] Board Unit [EP] Board Unit [R] Board Unit [T] Board Unit [PP] Board Unit [S] Board Unit [H] Main (Not Replacement Item) (PWB-A) Key (Not Replacement Item) (PWB-B) Back Light FPC (PWB-C) Camera Unit (CA1001) Main Display Holder Assembly External Display Holder Assembly Shield Case,BB Cushion,Aerial Cushion,Connector Cushion,Camera Unit Protect Sheet,Camera Insulator,BB Sheet,Side Keys Shield Plate,BB Case RF,Shield (Cover) Case RF,Shield (Frame) Case,Shield Camera Ground FPC (PWB-D) Ground FPC (PWB-E) Contact,Spring (A) Contact,Spring (B) Main Display (LCD1000) External Display (LCD001) Camera Relay FPC (PWB-F) SD/SIM FPC (PWB-G) Sensor,Moisture Cap,Aerial Screw Cover,Display (Small)

! !

! !

11

GX30
NO. PARTS CODE

CONFIDENTIAL
PRICE NEW PART RANK MARK RANK DESCRIPTION

[13] CABINET PARTS

107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 124 124 125 126 601 GCOVA2569AFSA GCOVAA039AFZZ GCOVD1119AFSU GCOVH1358AFSA GCOVH1359AFSA JKNBPA002AFSA JKNBZ2371AFSA JKNBZ2372AFSA LHLDZ1952AFSA PCUSSA029AFZZ PSHEMA001AFZZ PSLDCA002AFZZ RDNTL0015AFZZ RMICC0213AFZZ RMOTV0557AFZZ RPHODA002AFZZ RSP-ZA001AFZZ TSPC-A088AFZZ TSPC-A089AFZZ TSPC-A090AFZZ PSHEZA204AFZZ -------LX-EZ0195AFZZ AD AR AB AC AD AG AW AG AC AC AD AD AG AL AM AK AM DD DD DD AB -AB Screw Cover,Display (Large) Frame,Side Screw Cover,Key Cover,Jack (Hands Free) Cover,External Connector Lever,Close-up Button,10 Key Keys,Side Holder,Camera Cushion,Camera Sheet,Aerial Shield Case,Camera Battery,Back-up (BAT100) Microphone (MIC100) Vibrator (MO100) Earpiece (EP100) Speaker (SP100) Label,Specifications (Except for [A, Z, F]) Label,Specifications [A, Z] Label,Specifications [F] Sheet,Earpiece (A) Sheet,Earpiece (B) (Not Replacement Item) Screw (1.7x5)

12

CONFIDENTIAL
[14] ACCESSORIES/PACKING PARTS
13, 14 ([T] Only), 15, 16 ([B] Only), 17, 18, 19 10 1 9, 23 11 3 22 25 24 ([EP] [H] [F] [C] [K] [U] Only)

GX30

2 6

Handset 21 27 ([U] Only) 24

28 ([B] Only) 4 5
AC Charger RADPAA001AF01 RADPAA002AF01 RADPAA003AF01

20 ([E] [B] [D] Only) 26 ([G] Only)

NO.

PARTS CODE

PRICE NEW PART RANK MARK RANK

DESCRIPTION

[14] ACCESSORIES/PACKING PARTS

! ! !

1 2 2 2 3 4 5 5 5 5 6 7 8 9 10 11 11 13 13 13

GFTAB1412AFSA RADPAA001AF01 RADPAA002AF01 RADPAA003AF01 RUNTZ0893AFZZ SPAKA2823AFZZ SPAKCA031AFZZ SPAKCA067AFZZ SPAKCA086AFZZ SPAKCA162AFZZ SPAKP1252AFZZ SPAKP1284AFZZ SPAKXA019AFZZ SSAKAA003AFZZ SSAKH0329AFZZ SSAKH0337AFZZ SPAKPA013AFZZ TCADHA015AFZZ TCADHA016AFZZ TCADHA017AFZZ

AG ** ** ** AS AG AM AK AM AK AC AC AD AC AA AB AC AF AF AP

Cover,Battery AC Charger [E, EP, R, L] (XN-1QC30) AC Charger [G, T, PP, S, H, W, B, D, Q, F, C, K, U] (XN-1QC31) AC Charger [A, Z] (XN-1QC32) Hands Free Kit Packing Add. Packing Case [E, G, B, D, PP, R, T, S, W, L, Q] Packing Case [EP, H, F, C, K] Packing Case [A, Z] Packing Case [U] Polyethylene Bag,AC Charger Polyethylene Bag,Unit Spacer SD Soft Case Polyethylene Bag,Battery Cover Polyethylene Bag,User Guide (Except for [U]) Polyethylene Bag,User Guide [U] Quick Start Guide [E, EP, A, Z, Q, R, L] Quick Start Guide [G] Quick Start Guide [S]

13

GX30
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[14] ACCESSORIES/PACKING PARTS

13 13 13 13 13 13 14 15 15 15 15 15 15 15 15 15 15 15 15 15 16 17 17 17 17 17 17 17 17 17 17 17 18 18 18 18 18 18 18 18 18 18 18 18 18 18 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 20 21 22 23 23 24 25 26 27 28 TCADHA018AFZZ TCADHA019AFZZ TCADHA020AFZZ TCADHA021AFZZ TCADHA022AFZZ TCADHA023AFZZ TCADZ0263AFZZ TCADZA006AFZZ TCADZA013AFZZ TCADZA014AFZZ TCADZA016AFZZ TCADZA017AFZZ TCADZA018AFZZ TCADZA019AFZZ TCADZA034AFZZ TCADZA042AFZZ TCADZA051AFZZ TCADZA053AFZZ TCADZA055AFZZ TCADZA057AFZZ TCADZA020AFZZ TCADZA022AFZZ TCADZA023AFZZ TCADZA024AFZZ TCADZA025AFZZ TCADZA026AFZZ TCADZA028AFZZ TCADZA038AFZZ TCADZA052AFZZ TCADZA054AFZZ TCADZA056AFZZ TCADZA058AFZZ TGANEA001AFZZ TGANEA009AFZZ TGANEA010AFZZ TGANEA011AFZZ TGANGA002AFZZ TGANIA002AFZZ TGANZA012AFZZ TGANZA013AFZZ TGANZA014AFZZ TGANZA015AFZZ TGANZA016AFZZ TGANZA017AFZZ TGANZA018AFZZ TGANZA026AFZZ TINSEA004AFZZ TINSEA018AFZZ TINSEA028AFZZ TINSFA012AFZZ TINSFA014AFZZ TINSGA002AFZZ TINSGA019AFZZ TINSGA020AFZZ TINSHA008AFZZ TINSHA013AFZZ TINSIA007AFZZ TINSPA010AFZZ TINSSA009AFZZ TINSWA011AFZZ TINSZA005AFZZ TINSZA006AFZZ TLABZ2793AFZZ UBATIA004AFZZ UDSKAA014AF01 UIMC-A002AFZZ UIMC-A003AFZZ -------SSAKA0233AFZZ TLABZA044AFZZ TLABZA061AFZZ TLABZA059AFZZ AG AP AP AP AL AH AC AB AB AC AE AE AC AD AC AC AC AB AB AB AD AB AD AD AD AD AC AB AC AB AE AB AE AE AC AC AE AC AD AE AD AE AE AC AK AP AK AL AK AK AL AL AP AK AL AP AP AP AN AN AA ** AK BC BC -AD AC AB Quick Start Guide [T] Quick Start Guide [PP] Quick Start Guide [H] Quick Start Guide [B] Quick Start Guide [W] Quick Start Guide [D] Card,Free Service ( [T] Only) Post Card Service Guide [E, EP, H, R] Post Card Service Guide [G] Post Card Service Guide [T] Post Card Service Guide [S] Post Card Service Guide [PP] Post Card Service Guide [D] Post Card Service Guide [W] Post Card Service Guide [C] Post Card Service Guide [F] Post Card Service Guide [K] Post Card Service Guide [U (English)] Post Card Service Guide [U (Datch)] Post Card Service Guide [U (French)] DOC Copy ( [B]Only) MML Service Guide [E, EP, R] MML Service Guide [S] MML Service Guide [T] MML Service Guide [PP] MML Service Guide [H] MML Service Guide [D] MML Service Guide [C] MML Service Guide [K] MML Service Guide [U (English)] MML Service Guide [U (Datch)] MML Service Guide [U (French)] Guarantee [Q, L] Guarantee [E, EP] Guarantee [R] Guarantee [A, Z] Guarantee [K] Guarantee [T] Guarantee [PP] Guarantee [D] Guarantee [W] Guarantee [B] Guarantee [C] Guarantee [H] Guarantee [S] Guarantee [U] User Guide [E, EP, R, Q, L] User Guide [A, Z] User Guide [U (English)] User Guide [F] User Guide [U (French)] User Guide [G] User Guide [C] User Guide [K] User Guide [H] User Guide [U (Datch)] User Guide [T] User Guide [PP] User Guide [S] User Guide [W] User Guide [D] User Guide [B] Sheet,Security ( [E, B, D] Only) Rechargeable Li-ion Battery (XN-1BT30) CD-ROM SD Card (Except for [C, F, K, U]) SD Card ( [C, F, K, U] Only) Label,Case Polyethylene Bag,CD-ROM Sheet,Transparent ( [G] Only) Label,Battery ( [U] Only) Label,Hungary ( [B] Only)

[15] P.W.B. ASSEMBLY

! !

PWB-A PWB-B PWB-C PWB-D PWB-E PWB-F PWB-G

--------------CUiTKA003AFZZ QPWBH0749AFZZ QPWBHA049AFZZ RUNTKA014AFZZ RUNTKA016AFZZ

--AM AK AH BC AX

Main (Not Replacement Item) Key (Not Replacement Item) Back Light FPC Camera Ground FPC Ground FPC Camera Relay FPC SD/SI FPC

14

GX30
INDEX

MEMO

15

GX30

CONFIDENTIAL

COPYRIGHT

2004

BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan B0406-PDF KS KJ J