Scribd
Upload
67 views2 pages

Ra6 GB 01

This document summarizes the specifications, composition, applications, properties, heat treatment requirements, and physical properties of steel grade X82WMoCrV6-5-4. Key details include: - The steel has a carbon content of 0.85% and contains tungsten, molybdenum, chromium, and vanadium. - It can be used for shear blades, parts exposed to abrasion, and dies of simple form. - Heat treatment requires preheating, heating to 1150-1200°C, and air or gas quenching followed by tempering between 550-600°C. - Hardness ranges from 70-30 HRC depending on tempering temperature.

Uploaded by

Nguyen Quoc Tuan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
67 views2 pages

Ra6 GB 01

This document summarizes the specifications, composition, applications, properties, heat treatment requirements, and physical properties of steel grade X82WMoCrV6-5-4. Key details include: - The steel has a carbon content of 0.85% and contains tungsten, molybdenum, chromium, and vanadium. - It can be used for shear blades, parts exposed to abrasion, and dies of simple form. - Heat treatment requires preheating, heating to 1150-1200°C, and air or gas quenching followed by tempering between 550-600°C. - Hardness ranges from 70-30 HRC depending on tempering temperature.

Uploaded by

Nguyen Quoc Tuan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Steel

RA6
X82WMoCrV6-5-4

SPECIFICATIONS
EN : ~ X82WMoCrV6-5-4 / ~ HS6-5-2 X82WMoCrV6-5-4 (former Z85WDCV6-5-4) AFNOR:

COMPOSITION
Carbon ..............................................0.85 Tungsten ............................................6.25 Molybdenum......................................5.25 Chromium ..........................................4.25 Vanadium ..........................................2.00

W.Nr AISI JIS

: ~ 1.3553 / ~ 1.3343 : ~ M2 : SKH51

APPLICATIONS PROPERTIES
Heat gradually to 875C. Hold at 875C then cool slowly in the
furnace. Take usual precautions to avoid decarburization.

Shear blades. Parts exposed to abrasion. Dies of simple form. For cold work, toughness can be increased,
depending on the application, by lowering the hardening temperature and by adjusting the tempering temperature to achieve 60 HRC.

Softened condition, Brinell hardness approximately 240.

QUALITIES
Very good cutting properties. Very good abrasion resistance.

4554k

HEAT TREATMENT
Hardening:
- 1st preheat to 550C. - 2nd preheat to 850C. - Heat to 1150/1200C. - Air cool or gas pressure quench. For large parts, air cooling may be replaced by hardening in a salt bath at 550C, followed by cooling in air to room temperature. It is recommended that heating should take place in a neutral atmosphere.

HARDNESS VS TEMPERING
TEMPERATURE

HRC 70 65 60 55 50 45 40 35 30

Tempering:
- Between 550 and 600C, depending on hardening temperature and hardness required. Double or triple temper required. - After hardening at 1180C and double temper at 550C: hardeness approximately 62 HRC.

PHYSICAL PROPERTIES
Density:
8.2

100

200

300

400

500

600

700C

Mean coefficient of expansion in m/m.C:


- between 20C and 200C: 10.30 x 10-6 - between 20C and 400C: 11.60 x 10-6 - between 20C and 600C: 12.25 x 10-6 Heated to 1180C, air cooled. (Test on 1 cm thick specimen)

Critical points:
- Ac 1: - Ac 3: 830C 880C

FORGING
1150/925C
AUBERT & DUVAL
Tour Maine Montparnasse 33, avenue du Maine 75755 Cedex 15 www.aubertduval.com

The data provided in this document represent typical or average values rather than maximum or minimum guaranteed values. The applications indicated for the grades described are given as guidance only in order to help the reader in his personal assessment. Please note that these do not constitute a guarantee whether implicit or explicit as to whether the grade selected is suited to specific requirements. Aubert & Duvals liability shall not under any circumstances extend to product selection or to the consequences of that selection.

4554k

RA6

You might also like