Scribd
Upload
453 views4 pages

Effectiveness Ntu Method

This document discusses heat transfer analysis using the effectiveness-NTU method for heat exchangers. It provides equations to calculate the maximum possible heat transfer, actual heat transfer rate, effectiveness, number of transfer units (NTU), and capacity ratio. The effectiveness can be determined from charts or equations based on heat exchanger geometry and flow arrangement. Three examples problems are given to calculate the required length, heat transfer rate, and outlet temperatures for counter-flow and multi-pass shell-and-tube heat exchangers.

Uploaded by

Ben Musimane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
453 views4 pages

Effectiveness Ntu Method

This document discusses heat transfer analysis using the effectiveness-NTU method for heat exchangers. It provides equations to calculate the maximum possible heat transfer, actual heat transfer rate, effectiveness, number of transfer units (NTU), and capacity ratio. The effectiveness can be determined from charts or equations based on heat exchanger geometry and flow arrangement. Three examples problems are given to calculate the required length, heat transfer rate, and outlet temperatures for counter-flow and multi-pass shell-and-tube heat exchangers.

Uploaded by

Ben Musimane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

HEAT TRANSFER

ANALYSIS OF HEAT EXCHANGER


The Effectiveness NTU Method
This method is based on a dimensionless parameter called the heat
transfer effectiveness, . Where
rate tranfer heat possible imum
rate transfer heat actual
q
q
max
max

The actual heat transfer rate can be determined from


out h in h h
in c out c c
T T C q
T T C q
, ,
, ,


Where
pc c c
ph h h
C m C
C m C

The maximum possible heat transfer rate is given by



in c in h
T T C q
, , min max

Where C
min
is the smaller of C
h
and C
c
and T
max
= T
h,in
- T
c,in
The determination of q
max
requires the availability of the inlet
temperature of the hot and cold fluids and their mass flow rates, which
are usually specified. Then, once the effectiveness of the heat exchanger
is known, the actual heat transfer rate q can be determined from

in c in h
T T C q
q q
, , min
max

To determine the effectiveness, we involve a dimensionless quantity


called number of transfer units which is expressed as
min
C
UA
NTU
Take note how, the larger the NTU, the larger the heat exchanger.
Another dimensionless quantity used is the capacity ratio, c which is
expressed as
max
min
C
C
c
Hence, the effectiveness of a heat exchanger which depends on the
geometry of the heat exchanger as well as the flow arrangement can be
determined from the expressions given in the table below.
The effectiveness, can also be determined graphically from Figure
13-26.
Subsequently, if we know , we can determine the NTU number from the
expressions in the table below.
Analysis of Heat Exchanger: Effectiveness NTU Method
1. A counter-flow double-pipe heat exchanger is to heat water from
20C to 80C at a rate of 1.2 kg/s. The heating is to be
accomplished by geothermal water available at 160C at a mass
flow rate of 2 kg/s. The inner tube is thin-walled and has a diameter
of 1.5 cm. If the overall heat transfer coefficient of the heat
exchanger is 640 W/m
2
K, determine the length of the heat
exchanger required to achieve the desired heating.
2. Hot oil is to be cooled by water in a 1-shell-pass and 8-tube-passes
heat exchanger. The tubes are thin-walled and are made of copper
with an internal diameter of 1.4 cm. The length of each tube pass in
the heat exchanger is 5 m, and the overall heat transfer coefficient
is 310 W/m
2
C. Water flows through the tubes at a rate of 0.2
kg/s, and the oil through the shell at a rate of 0.3 kg/s. The water
and the oil enter at temperatures of 20C and 150C, respectively.
Determine the rate of heat transfer in the heat exchanger and the
outlet temperatures of the water and the oil.
3. Hot oil (Cp = 2200 J/kg K) is to be cooled by water (Cp = 4180
J/kg K) in a 2-shell-pass and 12-tube-pass heat exchanger. The
tubes are thin-walled and are made of copper with a diameter of 1.8
cm. The length of each tube pass in the heat exchanger is 3 m, and
the overall heat transfer coefficient is 340 W/m
2
C. Water flows
through the tubes at a total rate of 0.1 kg/s, and the oil through the
shell at a rate of 0.2 kg/s. The water and the oil enter at
temperatures 18C and 160C, respectively. Determine the rate of
heat transfer in the heat exchanger and the outlet temperatures of
the water and the oil.

You might also like