Objectives: Fasteners 360102e WORKSHEET

1)

Identify the 8 typical finishes for fasteners and their corresponding characteristics. (p. 2)
a) ________________________________
i)

________________________________________________________________

b) _______________________________
i)

________________________________________________________________

c) _______________________________
i)

________________________________________________________________

d) _______________________________
i)

________________________________________________________________

e) _______________________________
i)
f)

________________________________________________________________

_______________________________
i)

________________________________________________________________

g) _______________________________
i)

________________________________________________________________

h) _______________________________
i)

________________________________________________________________

2) List 5 typical nail shank textures. (p. 3)

a) _________________________________________
b) _________________________________________
c) _________________________________________
d) _________________________________________
e) _________________________________________

3) What is the general guideline for nail length when fastening two members? (p. 3)
a) _______________________________________________________________________
_______________________________________________________________________

4) List the 9 different nail styles outlined in the ILM and their distinguishing features (shank size, head type, typical
finish etc.) (p. 4)
a) ________________________________
i)

________________________________________________________________

b) ________________________________
i)

________________________________________________________________

c) ________________________________
i)

________________________________________________________________

d) ________________________________
i)

________________________________________________________________

e) ________________________________
i)
f)

________________________________________________________________

________________________________
i)

________________________________________________________________

g) ________________________________
i)

________________________________________________________________

h) ________________________________
i)
i)

________________________________________________________________

________________________________
i)

________________________________________________________________

5) Give two examples of each type of staple and an application of each. (p. 5)
a) Light Duty
i)
_______________________________________________________________
ii)

_______________________________________________________________.

b) Heavy Duty
i)
_______________________________________________________________
ii)

_______________________________________________________________

6) What three pieces of information are typically used to identify staples?

a) _________________________________________________
b) _________________________________________________
c) _________________________________________________

7) What advantages do screws have over nails? (p. 5)

a) ____________________________________________________________________________
b) ____________________________________________________________________________

8) What feature typically identifies wood screws and what is its purpose?(p. 6)
a) ____________________________________________________________________________

9) Identify the three pieces of information required to order screws. (p. 7)

a) _______________________________
b) _______________________________
c) _______________________________

10) Name 8 common screw head profile shapes. (p. 7)

a) _______________________________
b) _______________________________
c) _______________________________
d) _______________________________
e) _______________________________
f)

_______________________________

g) _______________________________
h) _______________________________

11) Name 6 common screw head recess types. (p. 8)

a) _______________________________
b) _______________________________
c) _______________________________
d) _______________________________
e) _______________________________
f)

_______________________________

12) Describe the key features of the following special purpose screws. (p. 9-10)
a) Wood
i)
____________________________________________________________________________
b) Sheet metal
i)
____________________________________________________________________________
c) Self-Tapping and Self-Drilling
i)

____________________________________________________________________________

ii)

____________________________________________________________________________

d) Drywall
i)
____________________________________________________________________________
e) Deck
i)
f)

____________________________________________________________________________

Lag Screw/Bolt
i)
____________________________________________________________________________

g) Self Sealing
i)
____________________________________________________________________________
h) Hook and Eye
i)
____________________________________________________________________________
i)

Hanger Bolts
i)
____________________________________________________________________________

j)

Dowel Screws
i)
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________

13) List the 4 preparatory steps for fastening screws in the order that you would perform them and their purpose.
(p. 10,11)
a) COUNTERBORE
i)
____________________________________________________________________________
____________________________________________________________________________
b) COUNTERSINK
i)
____________________________________________________________________________
____________________________________________________________________________
c) PILOT HOLE
i)
____________________________________________________________________________
____________________________________________________________________________
d) CLEARANCE HOLE
i)
____________________________________________________________________________
____________________________________________________________________________

14) Identify the purpose of each of the following Specialty Fasteners as described in your ILM. (p. 12-17)
a) Tamper Resistant Screws
i)
____________________________________________________________________________
b) Decorative Caps
i)
____________________________________________________________________________
c) Ready-To-Assemble (RTA) Fasteners
i)
____________________________________________________________________________
____________________________________________________________________________
d) Ready Rods
i)
____________________________________________________________________________
____________________________________________________________________________
e) Draw Bolts
i)
____________________________________________________________________________
____________________________________________________________________________
f)

Stove Bolts
i)
____________________________________________________________________________
____________________________________________________________________________

g) Machine Screws
i)
____________________________________________________________________________
____________________________________________________________________________
h) European Assembly Screws
i)
____________________________________________________________________________
____________________________________________________________________________
i)

Connector Bolts
i)
____________________________________________________________________________
____________________________________________________________________________

j)

Machine Bolts
i)
____________________________________________________________________________
____________________________________________________________________________

k) Carriage Bolts
i)
____________________________________________________________________________
____________________________________________________________________________

15) What is an important consideration in cutting threaded rod or bolts to size? (p. 15)
i)
____________________________________________________________________________
____________________________________________________________________________

16) Identify 4 common types of nuts and their purpose. (p. 19)
a) _______________
i)

____________________________________________________________________________

b) _______________
i)

____________________________________________________________________________

c) _______________
i)

____________________________________________________________________________

d) _______________
i)

____________________________________________________________________________

17) Identify 5 common types of washers and their purpose. (p. 19)
a) _______________
i)

____________________________________________________________________________

b) _______________
i)

____________________________________________________________________________

c) _______________
i)

____________________________________________________________________________

d) _______________
i)

____________________________________________________________________________

e) _______________
i)

____________________________________________________________________________

18) Identify key features of the following anchors (hole required y/n, fastener used, hollow or solid material etc.). (p.
20-24)
a) PLASTIC SCREW ANCHORS
i)

____________________________________________________________________________
____________________________________________________________________________

b) MASONRY/LEAD ANCHORS
i)

____________________________________________________________________________
____________________________________________________________________________

c) EXPANSION SHIELD ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

d) DRIVE PIN ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

e) WEDGE/SLEEVE ANCHORS
i)

____________________________________________________________________________
____________________________________________________________________________

f)

DROP IN EXPANSION SHELL ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

g) MASONRY SCREW ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

h) SCREW IN ANCHORS
i)

____________________________________________________________________________
____________________________________________________________________________

i)

TOGGLE BOLT
i)

____________________________________________________________________________
____________________________________________________________________________

j)

SCREW IN TOGGLE ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

k) PLASTIC/NYLON TOGGLE ANCHORS

i)

____________________________________________________________________________
____________________________________________________________________________

l)

HOLLOW WALL (MOLLY BOLT) ANCHORS

i)
____________________________________________________________________________
____________________________________________________________________________