0% found this document useful (0 votes)
88 views6 pages

WCE2012 pp1716-1721 PDF

The document describes a new type of seismic isolation system called a friction pendulum with parameterized sliding surfaces. This system allows for greater flexibility in controlling the oscillations of an upper structure through the use of three parameters (friction coefficient and two characteristic values of the curve defining the sliding surface) compared to traditional friction pendulums. Finite element analysis was used to analyze the behavior of this new system and confirmed that using an elastomeric element between the slider and sliding surface can achieve a uniform pressure distribution.

Uploaded by

Euge Compagnoni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
88 views6 pages

WCE2012 pp1716-1721 PDF

The document describes a new type of seismic isolation system called a friction pendulum with parameterized sliding surfaces. This system allows for greater flexibility in controlling the oscillations of an upper structure through the use of three parameters (friction coefficient and two characteristic values of the curve defining the sliding surface) compared to traditional friction pendulums. Finite element analysis was used to analyze the behavior of this new system and confirmed that using an elastomeric element between the slider and sliding surface can achieve a uniform pressure distribution.

Uploaded by

Euge Compagnoni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Abstract The new approach proposed by the authors in

this paper consists of implementing friction pendulums having


the sliding surface profile based on a polynomial function of
superior order. This seismic isolation system permits, for each
surface, a greater flexibility in controlling the oscillations of the
upper structure, in terms of displacements or dissipated
energy, by using three parameters to control the force-
displacement relation.
Index Termsisolation system, dissipated energy, friction
pendulum, finite element analysis

I. INTRODUCTION

or safety and integrity reasons against earthquakes,
effective and reliable techniques are desired. The
optimum solution against earthquake effects is to
control and limit the transfer of energy from the ground to a
superstructure that means to dissipate this energy [1].
For these reasons, the actual trend is represented by using
the friction pendulum. This is a sturdy passive device,
capable to sustain significant loads and to assure the control
of oscillating structures [2].
Friction pendulums can be classified, according to the
number of sliding surfaces, in mono-armature or multi-
armature [3]. While classical friction pendulum bearings
contain one or more cylindrical or spherical sliding surfaces,
each having a radius of curvature R and friction coefficient
, they provide just pairs of two parameters controlling the
dynamic behaviour of a structure isolated by this kind of
device. The friction pendulum system with one concave
spherical shaped sliding surface is presented in [4] while the


Manuscript received March 18, 2012; revised April 16, 2012.
This work was supported in part by the Managing Authority for
Sectorial Operational Program for Human Resources Development
(MASOPHRD), within the Romanian Ministry of Labor, Family and Equal
Opportunities by co-financing the project Doctoral Scholarships investing
in research-development-innovation for the future (DocInvest)
POSDRU/107/1.5/S/76813.
A. A. Minda is with the Economical Engineering Department, Eftimie
Murgu University of Resita, 320085 Romania. (e-mail: [email protected]).
G. R. Gillich is with the Mechanical Engineering Department, Eftimie
Murgu University of Resita, 320085 Romania. (e-mail:
[email protected]).
C. M. Iavornic is with the Mechanical Engineering Department, Eftimie
Murgu University of Resita, 320085 Romania. (e-mail:
[email protected]).
P. F. Minda is with the Mechanical Engineering Department, Eftimie
Murgu University of Resita, 320085 Romania. (e-mail: [email protected]).

double concave bearing was presented in [5].
A new base isolator, called a variable curvature friction
pendulum system, was introduced by Tsai , Chiang and
Chen in [6]. The difference between the variable curvature
friction pendulum system and the friction pendulum system
is that the isolators radii can be lengthened with the
increase of the isolator displacement. Pranesh and Sinha
introduced in [7] and [8] a variable curvature friction
pendulum system with the sliding surface based on an
ellipse. The major axis of the ellipse can be lengthened with
increase of sliding displacement. They have made analysis
in terms of behaviour of the isolated structure, without being
analyzed the behaviour of the friction pendulum itself.
The new approach proposed by the authors in this paper
consists of implementing friction pendulums having the
sliding surface profile based on a polynomial function of
superior order. This seismic isolation system permits, for
each surface, a greater flexibility in controlling the
oscillations of the upper structure, in terms of displacements
or dissipated energy, by using three parameters to control
the force-displacement relation. Namely, these parameters
are the friction coefficient , and two characteristic values
of the curve on which the sliding surface is constructed.
Opposite to classical systems, where the contact between
the slider and the sliding surface assured almost uniformly
distributed contact stress even for metallic components, the
new devices make use of an elastic element between the
slider and the sliding surface. A quasi-uniform pressure
distribution on the sliding surface can be obtained in this
way. Static and dynamic analyses were performed using the
finite element method confirming that the use of an
elastomeric element is suitable for this purpose.

II. MATHEMATICAL MODEL OF SIMPLE FRICTION
PENDULUM WITH SLIDING SURFACES GENERATED BY
POLYNOMIAL FUNCTIONS

In the case of the simple friction pendulum, with
cylindrical or spherical sliding surface, the control of the
movement can be made with two parameters: the radius of
the pendulum R and the friction coefficient .
The height variation h expressed in terms of o and then
in terms of displacement u, is:
Analytical and Finite Element Study for Friction
Pendulum with Parameterized Sliding Surfaces
Andrea Amalia Minda, Member, IAENG, Gilbert-Rainer Gillich Member, IAENG, Claudiu Mirel
Iavornic, Member, IAENG and Petru Florin Minda, Member, IAENG
F
Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012

( ) 1 cos 1 cosarcsin
u
h R R
R
o
| |
= =
|
\ .
(1)
The friction force value is
( )
f
F N sign u = (2)
The signum function is equal to -1 or +1 depending on
whether u is negative or positive, respectively. If we
consider the motion in the positive direction of Ox axis, we
can take ( ) 1 sign u = , so F
f
expressed in terms of o is
cos
f
F G o = , where G is the vertical loading resulting
from the structure.




Fig. 1. A simple friction pendulumscheme with the forces acting on
circular sliding surface

On the interval | |
max
0,u the dissipated energy due to
friction is:
( )
max
0
u
d f
E F u du =
}
(3)
or
max max
0 0
cos cos
u u
d
E G du G du o o = =
} }
.
By changing the variable sin u R o = , one obtain
cos du R d o o = , and consequently the integral calculated
on | |
max
0,u becomes an integral calculated on | |
max
0,o ,
hence the dissipated energy becomes:
max
2 2
0
cos
d
E GR d
o
o o =
}
(4)
where
max
max
arcsin
u
R
o = (5)
Solving the integral from (4), we obtain:
( )
max max max
1
sin cos
2
d
E GR o o o = + (6)
The dissipated energy on the interval | |
max
0,u ,
expressed in terms of maximum displacement
max
u is:
2 2 max max
max
2
1
arcsin
2
d
u u
E GR R u
R
R

( | |
= +
( |
\ .
(7)

For the friction pendulum with the sliding surface
generated by polynomial functions we consider the
equation of the curve that generates the sliding surface as:
b
y a u = (8)
To simplify calculations, we consider further only the
positive Ox axis, i.e. positive values of u, because the curve
is symmetrical to the vertical Oz axis.




Fig. 2. A friction pendulumscheme with polynomial sliding surface

Norms limit the value of the angle to
max
36 o ~

; for the
polynomial functions having 2, 2,5 b b = = and 4 b = we
calculated the maximum displacements
max
u and the
maximum heights
max
h calculated for different values of
a , presented in the table below.

TABLE I
b a
max
u

max
h

2
0,242 1,50
1
0,5
45
0,23 1,57 0,5
66
0,3 1,81 0,9
82
2,5
0,275 1,03
7
0,3
01
0,3 0,97
9
0,2
60
0,25 1,1 0,3
48
4
0,18 1,00
5
0,1
83
0,2 0,96
8
0,1
75
0,15 1,06 0,1
89

For a circular sliding surface with the radius 5 R = , for
max
36 o ~

we have determined the values of
max
u =2,93
and
max
0,948 h = .



Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012


Fig. 3. Graphical representation of different curves
that generates the sliding surface

In Fig. 3 we have shown the graphical representation of a
circular arc with the radius 5 R = (with dotted line) and the
arcs of equations
2
0,242 y u = (with dashed line),
2,5
0,275 y u = (with solid line) and
4
0,18 y u = (with dash-
dot line).
The dissipated energy is:
( )
max
0
u
d f
E F u du =
}
(9)
where ( )
f
F N sign u = is the friction force.
If we consider the motion in the positive direction of Ox
axis, we can take ( ) 1 sign u = , thus cos
f
F G o = .
Hence, the dissipated energy is:
max max
0 0
cos cos
u u
d
E G du G du o o = =
} }
(10)
At the point A we have
1 b
tg h a b u o

' = = . The
instantaneous displacement in terms of o is:
1
1 1 b
u tg
a b
o
| |
=
|

\ .
(11)
and consequently
( )
1
1
1
1
1
2
1 1 1
1
cos
b
b
du tg d
a b b
o o
o

| |
=
|

\ .

The integral on [0,u
max
] becomes an integral on
[
max
0,o ], where
max
o is:
( )
1
max max
b
arctg a b u o

= (12)
so:
( )
2
2
1
max 1
0
1 1 1
1 cos
b
b
b
d
E G tg d
a b b
o
o o
o

| |
=
|

\ .
}
(13)
If we denote
2
1
b
d
b

and
2
1
1 1
1
b
c
a b b
| |
=
|

\ .
we have:
for the case that 2 b = :

2
2 1 max
max
1 2 1
, , ,cos
2 2 2 cos
d
d
c d d d
E G F
d
o
o

| | (
=
|
(

\ .


1
1
2 2 2
d d
t
| | | |
I I +
| |

\ . \ .

)
(14)
where
( )
( )
2 1 1
1 1
2 2 2
2
2
2 1 max
1
2
0
max
1 2
, , ,cos
2 2 2
2
1
2
1 2
1 cos
2 2
d d d
d
d d d
F
d
t t
dt
d d
b
t
o
o

(
=
(

| |
I
|

\ .
=
| | | |
I I
| |

\ . \ .
}


for 2 b = we have:
max max
max max
cos sin
1
2 2
ln
2
cos sin
2 2
d
E G
a
o o

o o
| |
+
|
| |
=
|
|
\ .
|

|
\ .
(15)

In Fig. 4 we have represented the dissipated energies for
the different sliding surfaces generated by the curves
represented in Fig. 3. One can observe that for higher values
of u there are significant changes in the dissipated energy
for the analysed cases.


Fig. 4. The dissipated energies for the different sliding surfaces

The kinetic energy of the structure of mass m is given by

2
2
k
mv
E =
where v is the velocity.
We denote by
max
p
E the maximum potential energy, given
by:

max
max p
E mgh =
So, if friction is not considered
max
k p p
E E E = (16)
2
max
2
mv
mgh mgh =
and thus the maximum velocity, attended for 0 u = is
( )
max
2 v g h h = (17)

Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012


Fig. 5. The evolution of velocities and the heights

In Fig. 5 we have presented the evolution of velocities
and the heights while the structure moves from the point of
maximum vertical displacement to point O ( with 0 u = ),
for different types of sliding surfaces generated by
2
0,242 y u = (with dashed line),
2,5
0,275 y u = (with solid
line),
4
0,18 y u = (with dash-dot line) and a circular arc
with the radius 5 R = (with dotted line).
If we consider friction, the velocity in point O is given by

( )
max
2
2
d
E
v g h h
m
= (18)
where
d
E is the dissipated energy due to friction when the
structure slides from point A to point O (see Fig. 2).
In the next pictures (Fig. 6, Fig. 7, Fig. 8 and Fig. 9) we
have presented the evolution of velocities, first for the
sliding without friction (with dash-dot line), next for the
sliding with energy dissipation due to friction (with solid
line), for the sliding surfaces generated by a circular arc
with the radius 5 R = (Fig. 6),
2,5
0,275 y u = (Fig. 7),
2
0,242 y u = (Fig. 8) and for
4
0,18 y u = (Fig. 9). Note that
due to friction the structure no longer climbs to the same
height it would climb if it were frictionless.



Fig. 6. The evolution of velocities for the circular sliding surface, for the
sliding with and without friction




Fig. 7. The evolution of velocities for the sliding surface generated by
2,5
0,275 y u = , for the sliding with and without friction



Fig. 8. The evolution of velocities for the sliding surface generated by
2
0,242 y u = , for the sliding with and without friction




Fig. 9. The evolution of velocities for the sliding surface generated by
4
0,18 y u = , for the sliding with and without friction

Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012

III. FINITE ELEMENT STUDY AND RESULTS

Earthquake isolation systems are devices located at the
base of overhead structures, which have the aim to reduce
the structure oscillating period during an earthquake and
decrease the transmitted energy using frictional dissipation.
Classical isolation systems, with cylindrical or spherical
sliding surfaces have the parts made of stainless steel, which
provides durability. During earthquake, the slider and the
concave surface of the lower plate maintain contact and
consequently a relative uniform stress distribution is
assured. For other types of sliding surfaces, limited contact
occurs.
To prevent this kind of inconvenience, namely to obtain a
continuum contact between the slider and the concave plate,
it is necessary to insert an elastomeric layer between the
slider and the sole, as presented in Fig. 10. This layer is
similar to that used in elastomeric base isolation systems,
assuring high portability [9]. So we can avoid incomplete
contact (spotted or linear) and obtaining a controlled
deformation for fit the concave shape of stationary plate.




Fig. 10. Friction pendulumwith polynomial generated surface

The finite element analysis was made taking into account
the real-scale model of an earthquake isolation system and
transposing the whole loads, contacts and supports to virtual
model using advanced nonlinear analysis software.
Five curvature cases were analysed, one cylindrical and
four based on surfaces generated by polynomials, like that
presented in Fig. 11.


Fig. 11. Different types of sliding surfaces

For all cases, during the first second a vertical increasing
load was applied, until it reaches the weight of
superstructure. Afterwards, until the end of the considered
time interval of 2 seconds, a predetermined course
(simulating horizontal oscillation during an earthquake) was
imposed.

TABLE II
Case
Pressure
max. [MPa]
Contact pressure shape
2[s] (sole)
Arc

0.55427

Curve 1 0.22301

Curve 2 0.22059
Curve 3 0.21550
Curve 4 0.21313


Three main types of contacts were used for seismic
isolation system components: frictionless contact between
first concave plate and slider, frictional contact (=0.15)
between second concave plate and sole, bounded contact
between elastomeric layer and sole, elastomeric layer and
slider respectively.
Immediately after applying the vertical load, the sole is
elastically deformed and in the contact area a contact patch
is formed due to the pressure exerted by the elastomeric
layer on the opposite side. This patch can be quantitatively
evaluated using the contact pressure parameter. After 2
seconds, during the time period in which the horizontal
displacement is imposed because the gliding assembly has
been displaced, the contact patch becomes irregular with a
slight increase of the pressure value in the rear of the sole,
as we can see in Table II.
The normal stress distribution for entire assembly
together with its maximum value, at the end of the analysed
period, is presented in the Table III.


TABLE III
Case

Stress
max.[MP]
Normal stress 2[s]
(Assembly)
Curve 1 0.21997
Curve 2 0.20032
Arc 0.19300
Curve 3 0.17180
Curve 4 0.17413
Curve 2 0.20032

From the entire sets of results obtained using finite
element analysis (FEA) we chose to present the variation of
the contact pressure between the upper concave plate and
the slider for all analysed cases, determined after 1 and 2
seconds respectively.
Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012




Fig. 12. Contact pressure between the upper concave plate and the slider
determined after 1 and 2 seconds respectively

This diagram was obtained evaluating the contact region
between upper concave plate and slider after the first time
interval of 1[s] when the load is vertical and pressing the
assembly and then at the end of the second time interval of
2[s] when the load is combined (horizontal and vertical).

IV. CONCLUSION
For classical earthquake isolation systems the dynamic
response control is limited due to the reduced number of
control parameters. In order to avoid this deficiency, this
study shows the optimal way to improve the adjustment of
elastic characteristics for a large exciter frequency spectrum
of the earthquake.
The use of plates with concave surfaces generated by
polynomials, for the case of friction, ensures higher speed
near the equilibrium position, thus better conditions to
restore the position prior to the earthquake.
Profile curves generated by polynomial functions show
the possibilities to achieve the goal of superior, controlled
energy dissipation.
While for the spherical surface the slider has the same
shape with the concavity of the plate, for the sliding
surfaces generated by other curves we must interpose,
between the slider and lower armature, an elastomeric
element able to follow the changes of the curvature. Finite
element analysis proved that the normal stress values are
reduced in case of use this kind of earthquake isolation
system; all values for stress magnitude fall in the allowable
range.
REFERENCES
[1] T. Hyakuda , K. Saito, T. Matsushita, N. Tanaka, S. Yoneki, M.
Yasuda, M. Miyazaki, A. Suzuki, T. Sawada, The structural design
and earthquake observation of a seismic isolation building using
Friction Pendulum system, Proceedings, 7th International Seminar on
Seismic Isolation, Passive Energy Dissipation and Active Control of
Vibrations of Structures, Assisi, Italy, 2001.
[2] Y. B. Yang, T. Y. Lee and I. C. Tsai, Response of multi-degree-of-
freedom structure with sliding supports, Earthquake Engrg. Struct.
Dyn. 19, 739752 , 1990.
[3] P. Roussis , M.C. Constantinou , Uplift-restraining friction pendulum
seismic isolation system, Earthq. Eng. Struct. Dyn. 35:577593, 2006.
[4] V.A. Zayas, S.S. Low, S.A. Mahin, A simple pendulum technique for
achieving seismic isolation, Earthquake Spectra 6, 317-333, 1990.
[5] MC. Constantinou, Friction Pendulum double concave bearing.
NEES Report, available at: http://nees.buffalo.edu/docs/dec304/FP -
DC%20Report-DEMO.pdf, 2004.
[6] CS. Tsai, TC. Chiang, BJ . Chen., Finite element formulations and
theoretical study for variable curvature friction pendulum system ,
Engineering Structures 25, 2003, 1719-1730.
[7] M. Pranesh, R. Sinha, Aseismic design of structure-equipament
systems using variable frequency pendulum isolator, Nuclear
Engineering and Design 231, 2004, 129-139.
[8] M. Pranesh, R. Sinha, VFPI: an isolation device for aseismic design,
Earthquake Engn. Struct. Dyn. 2000, 29, 603-627.
[9] C. M. Iavornic, Z.I. Praisach, O. Vasile, G.R. Gillich, V. Iancu, Study
of Stress and Deformation in Elastomeric Isolation Systems Using
the Finite Element Method, Recent Advances in Signal Processing,
Computational Geometry and Systems Theory - ISCGAV'11,
ISTASC'11 , pp. 239-244, 2011.

Proceedings of the World Congress on Engineering 2012 Vol III
WCE 2012, July 4 - 6, 2012, London, U.K.
ISBN: 978-988-19252-2-0
ISSN: 2078-0958 (Print); ISSN: 2078-0966 (Online)
WCE 2012

You might also like