Scribd
Upload
269 views3 pages

Futek Hid Electronic Specs

This document provides specifications for the FUTEK HID 250WDD3P electronic ballast. Some key specifications include: - It is designed for heavy duty and high temperature weather use. - The input rated voltage is 220V with a working voltage range of 160-260Vac and a frequency of 50/60Hz. - The output is for a 250W HPSV lamp with a voltage of 100V +/-5%. - Protection features include over voltage, over temperature, no load, and lamp fault protections. - It has dimming capabilities from 100% to 50% output in customized dimming steps.

Uploaded by

AEEE
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
269 views3 pages

Futek Hid Electronic Specs

This document provides specifications for the FUTEK HID 250WDD3P electronic ballast. Some key specifications include: - It is designed for heavy duty and high temperature weather use. - The input rated voltage is 220V with a working voltage range of 160-260Vac and a frequency of 50/60Hz. - The output is for a 250W HPSV lamp with a voltage of 100V +/-5%. - Protection features include over voltage, over temperature, no load, and lamp fault protections. - It has dimming capabilities from 100% to 50% output in customized dimming steps.

Uploaded by

AEEE
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

FUTEK HID ELECTRONIC -BALLAST

SPECIFICATIONS FOR MODEL: FT-HID 250WDD3P


Designed for heavy duty and high temperature weather use

PARAMETERS FT-HID 250WDD3 P


INPUT:
Rated Voltage 220V

Working Voltage Range 160 ~ 260 Vac

Frequency 50/60 Hz

System Current:
Full Capacity At 220V 1.2A +/- 5 %
Dimming Mode At 220V Lowest: 0.59A +/- 10%

System Circuit Power:


Full Capacity 265W +/- 5 % max
Dimming Mode Customized: Lowest 130W +/- 5 %

Power Factor: >0.99


Full Capacity
Dimming Mode > 0.96

Total Harmonic Distortion:


Full Capacity < 10%
Dimming Mode

OUTPUT:
Lamp Type HPSV 250- Philips Or Osram Or GE or equivalent

Lamp Wattage:
Full Capacity 250W +/- 2%
Dimming Mode Lowest at 106.2W +/- 5 %

Lamp Power Factor > 0.98

Lamp Voltage 100V + or – 5 %

Lamp Current Crest Factor < 1.6

Lamp Operating Frequency Range:


Full Capacity 45 ~ 52 KHz
Dimming Mode 63 ~ 70 KHz

Dimming Level Customized: From 100% to 50%

OPERATING ENVIRONMENT
Ambient Temperature (Ta) -20 ~ +65°C

Housing Temperature (Tc) Max +90°C + or – 10%

PROTECTION FEATURE:
Protection Enable,
No Load Condition
Reset by power reset

Hot Re igniting Time Approx 45~ 60 sec

Re ignition Before Tube Cooled Down Protection Enable,


Reset by power reset

Protection Enable,
Lamp Fault
Reset by power reset

Protected
Over Voltage > 270V ~ 420 Volt Auto connection when power back to normal working range

8 preprogrammed position via 3 DIP Switches according to attach


Dimming options dimming program ( Customized )

100% > 90% >75 % >65% > 50%


Dimming Range

1) Digital To Digital using 3micro-processors for maximum reliability


Dimming Technology 2) DD3 Technology , 5 Dimming steps
3) With Dimming Memory Position recall

Weight 1750 gm + or – 10%

Thermal Over Heat ( Tc > 100C) Protected ( micro processor thermal control 100C + 10C

Over and Under Voltage Protection Power Off “ Protected Under 140V and Over 270V “

Voltage Monitoring processor “GST” * Protected with 5 ~ 15 second Grouping Starting Technology *

Voltage Monitor Technology Delay Time ** 5 ~ 20 Seconds ( At start Mode Only )

STANDARD DESIGN TO COMPLIED:


Safety Standard EN60928

Performance Standard EN60929

EMC Immunity EN61547

Current Harmonic Emission EN61000-3-2

Voltage Flicker EN61000-3-3

RFI EN55015/CISPR 15
*GST : Grouping Start Technology will divide large quantities of Ballast in several groups with 2 seconds delay

Between each of them in order to minimize starting rush Intensity and to optimize supply transformer efficiency.

** Voltage Monitor Technology will protect ballast from Surge Current , bad contacts , non stable Voltage at start

*** Technical data subject to change without notice.

You might also like