Product data sheet
Characteristics
TCSEGPA23F14F
Profibus DP V1 remote master - for Premium/
Quantum/M340/M580 PLC
Main
Profibus DP
Product or component
type
Profibus DP V1 remote master
Kit composition
CD including the Master DTM for PRM configuration
inside UNITY
CD including the communication DTM
Communication gateway
Ethernet Modbus TCP to Profibus DP V1 gateway
Product compatibility
Quantum PLC
M340 PLC
Premium PLC
M580 PLC
Structure type
Industrial bus
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.
Range of product
Complementary
Physical interface
RS485
Method of access
Slave (Modbus TCP)
Master class 2 (Profibus DP)
Master class 1 (Profibus DP)
Mode of transmission
NRZ
Transmission support medium
Category 5 shielded twisted pair (STP) (Modbus TCP)
2 twisted shielded pairs cable (Profibus)
Transmission rate
10...100 Mbit/s for bus length of 100 m without repeater (Modbus TCP)
9.6 kbit/s for bus length of 4800 m with 3 repeaters (Profibus)
9.6 kbit/s for bus length of 1200 m without repeater (Profibus)
12 Mbit/s for bus length of 400 m with 3 repeaters (Profibus)
12 Mbit/s for bus length of 100 m without repeater (Profibus)
Number of slave
126
Number of inputs
Number of outputs
Communication service
Acyclic DP V1 communication (R/W) - class 1/2 master
Sync and freeze - class 1 master
Transfer slave diagnostic data - class 1 master
Set slave parameters (on power up) - class 1 master
Read/Write DP slave I/O data - class 1 master
Profibus FMS message handling not supported - class 2 master
Profibus FMS message handling not supported - class 1 master
No master/master dialogue - class 2 master
Manage monitoring request (Global CONTROL and Get Master Diag) - class 2
master
Check slave configuration (on power up) - class 1 master
Integrated connection type
Profibus DP - SUB-D 9 for Profibus DP V1
2 Ethernet TCP/IP - RJ45 for Modbus TCP
Current consumption
200 mA at 24 V DC (external)
Module format
Standard
Product weight
0.62 kg
Environment
Ambient air temperature for operation
0...60 C
Ambient air temperature for storage
-45...85 C
Relative humidity
10...95 % without condensation
Operating altitude
<= 2000 m
Aug 25, 2015
Offer Sustainability
Sustainable offer status
RoHS (date code: YYWW)
REACh
Not Green Premium product
Compliant - since 0937 -
Schneider Electric declaration of conformity
Reference contains SVHC above the threshold -
go to CaP for more details
TCSEGPA23F14F
Product data sheet
Mounting and Clearance
Module Mounting
At a glance
The PRM module can be installed either:
With its support plate as a standalone module on a DIN rail, grid or panel
Without its support plate as a Premium module inside the rack
Support Plate
Label
Meaning
Two holes diameter 5.5 mm (7/32 in) allowing the support plate to be fixed to a panel or to an AM1-PA pre-slotted plate,
with a center distance of 140 mm (5.51 in).
Tightening torque: 1 to 1.2 N-m (8.8 to 10.6 lb-in).
M4 fixing hole for securing the PRM module.
Two holes diameter 6.5 mm (0.26 in) allowing the support plate to be fixed to a panel or to an AM1-PA pre-slotted plate
with a center distance of 88.9 mm (3.5 in).
Slots for positioning the pins located at the bottom and rear of the module
Mounting on a DIN rail or Plate
Installation on Drilled plate
Installation on Din rail
Mounting Type
Dimensions
Dimensions
X
mm
in.
Drilled Plate
(AM1-PA)
Din Rail
(AM1-DE200)
mm
Y
in.
132.7
143.7
5.22
5.66
3
Mounting Type
Din Rail
Dimensions
(AM1-DP200)
136.2
5.36
Mounting on a Premium Rack
Mechanically, the PRM is mounted like other Premium modules. The support plate must be removed before mounting in this case.
Electrically, the PRM doesnt use the rack connector for communication or for power supply. It must be powered by an external power
supply.
To detach the module from its support plate, follow the steps below:
Step 1:
Step 2:
Unfasten the screw located in the top of the module to loosen it from itssupport.
Pivot the module forwards and disengage the pins from the holes located inthe bottom of the support.
Refer to the Premium documentation for a description of the installation on the rack.
