EPOXY GROUT

Resin Based Grout

HYGIENIC, HARD-WEARING, IMPERVIOUS, EPOXIDE RESIN-BASED GROUT, WITH VERY GOOD
CHEMICAL RESISTANT AND ABRASION RESISTANT, SUITABLE FOR FOOD INDUSTRY AND
WHERE STERILE CONDITION IS NECESSARY

Features
Sterile
Durable joints
Hygienic and chemical resistant
High strength
Stain and bacterial resistant
High abrasion resistant
Exceeds EN 13888 requirements
Conforms to the Overall Migration Standards laid down in 21 CFR
175 - 300 (April 1, 2011) of US - FDA for intended use for contact
with aqueous food products

ARDEX ENDURA (INDIA) PRIVATE LIMITED

Corporate Office & Regd. Office: 73/1B,
Byregowda Indl. Estate, Srigandhanagar,
Hegganahalli, Peenya 2nd Stage,
Bangalore - 560 091, Karnataka, INDIA.
Tel: +91-80-2836 1672 / 2836 1673
Fax: +91-80-2836 2078
E-mail: [email protected]

EPOXY GROUT
Resin Based Grout
HYGIENIC, HARD-WEARING, IMPERVIOUS, EPOXIDE RESIN-BASED GROUT, WITH VERY GOOD CHEMICAL
RESISTANT AND ABRASION RESISTANT, SUITABLE FOR FOOD INDUSTRY AND WHERE STERILE CONDITION IS
NECESSARY
DESCRIPTION

used, blend at slow speed (less than

300 rpm).

NOTE:

EPOXY GROUT is a three-part system,

comprising of PART A, PART B and PART C.
For ease of application and the ability to fill
tile / stone joints the grout is best mixed
to a smooth, creamy consistency.
EPOXY GROUT is Hygienic, hard-wearing,
impervious, epoxide resin-based grout with
a high degree of resistance to chemical
attack, abrasion and impact. The cured grout
does not transfer taints to foodstuffs, does
not permit the entry of bacteria or dirt and
is easily maintained in a sterile condition.
STANDARDS

Exceeds the performance requirements

of BS 5980 : 1980 for tensile strength.
Exceeds EN 13888 requirements
Conforms to the Overall Migration Standards
laid down in 21 CFR 175 - 300 (April 1, 2011)
of US - FDA for intended use for contact with
aqueous food products.

= Suitable
(1) Do not use showers for at least 2 weeks following
completion of grouting.
(2) Do not fill pool at least 3 weeks following completion
of grouting.

SURFACE PREPARATION

White

Alpine blue

Ivory

Dark blue

Cream

Copper brown

Beige

Dark brown

Yellow

Terra red

Mushroom

Burgundy

Pink

Grey

Light green

Steel grey

Dark green

Dark grey

Blue

Black

5. The mixed EPOXY GROUT is usable for

up to 45 minutes at 2710C.

Clean: All joints should be cleaned down

by washing with water containing detergent,
then with clean water.

In general the PART C usage will vary

depending on the consistency, temperature,
different usage conditions, walls and floors
building up of thickness, etc.
Grouting at certain points : stiffer
consistency required to 'stop' open-ended
joints or grout skirting tiles.

Ensure the joints are dry before grouting.

Movement Joints:
These should be provided in accordance with
BS 5385 : part 1 - 5 and may be filled with the
appropriate flexible sealant. Intermediate floor
joints should be reinforced with brass or
stainless steel. Use stainless steel where
hygiene is essential.

Fixing the Tiles:

It is essential that the tiles used are
appropriate for the service conditions and
are fixed in the correct manner.
Application Procedure:
Before commencing grouting the adhesive
bed must be set. It is essential that the tiles
used are appropriate for the service conditions
and are fixed in a solid bed of adhesive i.e.
ensuring that, as far as possible, no voids are
left behind / beneath the tiles. Refer to the
relevant product datasheet for setting / drying
times.

AREAS OF APPLICATION

Walls

Floors

Interior

4. Immediately pour the mixed grout onto the

working area.

Joints should be free from efflorescence,

laitance, dirt and other loose material.
Remove thoroughly by dry brushing.

SITE WORK INSTRUCTIONS

SURFACE CONSIDERATIONS

COLOURS

3. Slowly add the required amount of PART C

and mix until all the PART C has been
dispersed and a uniform colour is achieved.

Protect open joints from contamination and

ensure that they are clean, dry and free from
loose debris prior to grouting.
Do not grout at temperatures less than 50C or
in damp conditions.

Exterior

Dry Areas

Wet Areas

PART A

1.0 kg

Work Tops

PART B

400 g

Showers

(1)

PART C

3.6 kg

Swimming Pools

(2)

Heavily Trafficked Floors

Hygienic Sterile Areas

Chemical Resistance

Hydrotherapy Pools

(2)

MIXING
MIXING PROPORTION
*PARTS BY WEIGHT

*Part mixing is not permitted

The EPOXY GROUT

consistency can be
adjusted to suit the
application and site
conditions by varying
the quantity of PART C
added to the mixed
PART A and PART B.

1. Before use shake the bottle of PART B and

stir PART A.
2. Add all of PART B to all of PART A in a
suitable, clean container and thoroughly
mix together. If an electric drill mixer is

NOTE:

APPLICATION

Check Potential Staining Risk:

Apply EPOXY GROUT to a few tiles in small trial
area. If discolouration occurs or difficulties are
encountered with cleaning off (surplus grout),
apply ARDEX ENDURA PROTECTIVE TILE &
STONE SEALER and repeat trial. Ensure
adequate ventilation in working areas.
1. Using a hard rubber grout float, compact the
EPOXY GROUT into the joints ensuring that
they are completely filled. Work in small
areas and remove as much excess from the
tile surface as possible. Strike off excess
materials diagonally to the grout lines.
2. Plug open-ended joints with the stiffer mix to
prevent any slumping of the EPOXY GROUT
joints from occurring.
3. Within 30 minutes of mixing, clean off
surplus EPOXY GROUT. Use a Scrubber
dampened with clean water to break
down (emulsify) the grout residue. Use a
circular motion and keep the Scrubber flat
relative to the tile surface to achieve a flush
joint. Warm water, although not essential will
greatly ease the emulsification process. Do
not allow water to flow/run into ungrouted
joints.
4. Clean off the emulsified epoxy / water
residue with a fine sponge, taking care not
to drag EPOXY GROUT from the joints.
Clean diagonally to the grout lines.
5. Do not allow the haze to remain on the
surface for any longer than 45 minutes.
Care should be taken to avoid staining
tiles when grouting. This is especially applicable
when grouting unglazed floor tiles, quarry tiles,
and tiles with a matt glaze or textured surface.
Check the potential risk of staining by applying
the grout to a few tiles in a small trial area.
If working in food processing / preparation /
storage areas, keep tiles / mosaics dry and
NOTE :

DO NOT bring floor into service until

EPOXY GROUT is hard / cured. Avoid contact
between food and tiling for at least 7 days
after grouting.
TECHNICAL SPECIFICATION

EPOXY GROUT

@ 27 1 C

CHEMICAL RESISTANCE CHART SUMMARY OF RESULTS

CHEMICAL

EPOXY GROUT

Household Ammonia

**

Hydrobromic Acid

**

Hydrochloric Acid (dil)

**

Kerosene

***

Acetic Acid (5%)

**

Acetic Acid (10%)

Lactic Acid (3%)

**
*

Joint Width

2 - 20 mm

Acetone

Lime Juice

Pot Life

45 minutes

Acetyl Bromide

Linseed Oil

***

Setting Time

48 hours

Aluminium Bromide

***

Lubricating Oils

***

Temperature
Resistance

Prolonged
-300C to 500C
Intermittent
Up to 700C

Aluminium Fluoride

***

Methanol

**

Ammonium Bromide (5%)

**

Milk

***

Baking Soda

***

Nitrates

***

Nil (1)
Determined by the
Campden Food &
Drink Research
Association, UK.

Barium Hydroxide

***

Nitric Acid (10%)

Beer

***

Olive Oil

***

Oleic Acid

***

Boric Acid

***

Palm Kernel Oil

***

Specific Gravity

1.75

n-Butanol

***

Shore D Hardness

> 70

Water Absorption

EPOXY GROUT
BS.5980:1980 min.

Palm Oil

***

Paraffin Wax

***

***

Phenol

Calcium Hydroxide

***

Phosphoric Acid (10%)

**

Carbon Disulphide

Pine Oil

***

>4.5
0.95

Carbon Tetrachloride

Polypropylene Glycol

***

Carbonates

***

Potassium Hydroxide

***

Wet Condition (kN)

Carbonic Acid

***

Proprietary Sterilising Agents

***

>3.6
0.56

Castor Oil

***

Silicates

***

Chlorides

***

Sodium Carbonate

***

Chlorinated Paraffin

***

Sodium Chloride

***
**

@ 27 10C

Tensile Adhesion (14 day air)

Dry Condition (kN)

EPOXY GROUT
BS.5980:1980 min.

Butyl Acetate

Calcium Chloride

TYPICAL VALUE

EPOXY GROUT

Benzene

Exceeds the requirements of BS 5980 : 1980

SPACERS

Use ARDEX ENDURA spacers for uniform joint

width.

Chloroform

Sodium Hydroxide

Chromic Acid

Sodium Hypochlorite Soln.

Citric Acid

***

(15% available chlorine)

***

EPOXY GROUT has a shelf life of 12 months

when stored in normal dry conditions.

Coconut Oil

***

Soya Bean Oil

***

Cotton Seed Oil

***

Sugars

***

For more details please refer the relevant

product safety datasheet

Diesel Oil

***

Sulphates

***

Dilute Detergents

***

Sulphuric Acid (45%)

CHEMICAL RESISTANCE

Ethanol

***

Sunflower Seed Oil

***

Tannic Acid

***

STORAGE AND SHELF LIFE

EPOXY GROUT is resistant to a wide range of

liquids and chemicals, for specific information
please refer to the following ARDEX ENDURA
"Chemical Resistance" chart.

Ethyl Alcohol

Ethylene Glycol

***

Tetrahydronahpthalene

***

Fats

***

1,1,1- Trichloroethane

***

Ferric Chloride

***

Vegetable Oils

***

Fish Oil

***

Water

***

Fluorides (except HF)

***

White Spirit

***

Formic Acid

Gasoline

***

Ground Nut Oil

***

Heptane

***

NOTE:

*
**

Splash contact only

Contact for max. 24 hours before
washing off

*** Prolonged contact

PRECAUTIONS

Keep out of reach of children, wear suitable

protective clothing. gloves and eyes/face
protection. After contact with skin, wash
immediately with plenty of clean water.
In case of contact with eyes rinse immediately
with plenty of clean water and seek medical
advice.
COVERAGE ESTIMATES

Pack size

Coverage

5 kg
PART A 1.0kg
PART B 400g
PART C 3.6kg

Consumption depend
on joint width, size of
tiles and good
workmanship
Refer to the
theoretical coverage
calculation below:

1 kg
PART A 200g
PART B 80g
PART C 720g

Theoretical coverage calculation:

(Tile length + Tile breadth) x Tile thickness x Joint width x Specific gravity*
= kg/m2
.
(Tile length + Joint width) x (Tile breadth + Joint width)
NOTE:
* Specific gravity = 1.75
All the dimensions are in mm

CONDITIONS OF SALE

Sold subject to the Company's conditions

of sale which are available on request.
NOTE

The information supplied in this datasheet

is based upon extensive experience and
is given in good faith in order to help you.
Our Company policy is one of continuous
Research and Development; we therefore
reserve the right to update this information
at any time without prior notice. We also
guarantee the consistent high quality of our
products; however as we have no control over
site conditions or the execution of the work,
we accept no liability for any loss or damage
which may arise as a result thereof.

AHMEDABAD
AURANGABAD
BANGALORE
BHUBANESHWAR
CALICUT
CHENNAI
DELHI
ERNAKULAM
GOA
HUBLI
HYDERABAD
INDORE
JAIPUR
KOLKATA

079 26425310
9881249293
080 22230138
9937091799
0495 2333065
044 24748673
011 32092369
0484 2341044
0832 2750992
0836 2236919
040 27550293
0731 4021148
0141 2392993
033 23452581

LUCKNOW
LUDHIANA
MANGALORE
MUMBAI
PUNE
RAIPUR
RAILA
RAJKOT
SALEM
TRICHY
TRIVANDRUM
VIJAYAWADA
VISAKAPATNAM

0522 4043251
0161 2532170
0824 2442176
022 65133299
020 64781879
0771 6539055
9509764756
9328286287
0427 2211454
0431 6454649
0471 2558648
0866 3254587
0891 6469499

05/12

BRANCHES