Scribd
Upload
136 views1 page

(Instreng - Com) DP Flowmeter Rangeability

The document discusses the difference between a flow meter's maximum specified rangeability and its effective rangeability in an actual application. While some meters advertise high rangeabilities like 20:1 or 30:1 based on their maximum flow rates, their rangeability is often much lower, like 5:1-10:1, when considering typical maximum flows in applications. Specifying a meter based only on its maximum rather than the application's maximum flow can increase costs by requiring pipe downsizing. The document recommends specifying the minimum rangeability needed rather than the maximum to avoid unnecessary expenses.

Uploaded by

pradeep.selvarajan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
136 views1 page

(Instreng - Com) DP Flowmeter Rangeability

The document discusses the difference between a flow meter's maximum specified rangeability and its effective rangeability in an actual application. While some meters advertise high rangeabilities like 20:1 or 30:1 based on their maximum flow rates, their rangeability is often much lower, like 5:1-10:1, when considering typical maximum flows in applications. Specifying a meter based only on its maximum rather than the application's maximum flow can increase costs by requiring pipe downsizing. The document recommends specifying the minimum rangeability needed rather than the maximum to avoid unnecessary expenses.

Uploaded by

pradeep.selvarajan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Technical Note

00840-0800-4809, Rev AA
October 2009

Rosemount DP Flow

Rosemount DP Flowmeter Rangeability


APPLICATION AND METER MAXIMUM
(MYTH VS. REALITY)
One of the most common DP Flow Myths is that the
rangeability of DP Flow technology is typically 3:1.
This misperception is usually promoted by competing
technologies that claim high rangeability of 20:1 or
better.

This increases installation costs and permanent


pressure loss, which may not be acceptable. For this
reason, flow meter rangeability should be considered
from application maximum, not the meters maximum
specified flow rate.
It is also important to understand how the max to min
flow ratio relates to percent of the flow range.

Rangeability is usually defined as the ratio of


maximum to minimum flow. There are two definitions
of maximum flow which are commonly used in
specifying the rangeability of a flow meter. It is
important to understand the difference between the
two methods of defining the maximum flow because
it can mean the difference between a flow meter that
can measure the flow range of interest and one that
cant. The first way to define maximum flow is the
maximum flow rate that the flow meter can measure.
This is how most flow meters specify rangeability in
product literature.
The other way to define the maximum flow is the
maximum flow rate that occurs in a particular
application. This is how most DP flow meters are
specified. DP rangeability is always referred to from
the application maximum flow.
The distinction is critical because the specified meter
maximum is often 2 - 3 times application maximum.
In liquid applications, Vortex, Coriolis, Magnetic and
Ultrasonic flowmeters are designed to measure
maximum flow rates of 20-30 ft/sec. The optimum
economic flowing velocity for liquids is about 5-6
ft/second, and they rarely flow over 10 ft/sec. That
means that a flow meter with a 20 or 30:1 flow
rangeability from meter maximum, typically
measures less than a 10:1 flow range in most actual
processes. For gas applications, meter maximum
flows are also much higher than typical process
maximum flows.
To achieve the advertised meter maximum flow and
rangeability in a typical application, pipe size must be
reduced at the meter.

www.rosemount.com

FIGURE 1. Relationship between rangeability and percent


of maximum flow

Figure 1 shows the relationship between rangeability


and percent of maximum flow. Notice that 10:1
rangeability will measure down to 10% of maximum
flow. A meter with 20:1 rangeability will measure
down to 5% of maximum flow; only 5% more of the
flow range. Since a meter with a high rangeability
can significantly increase the cost, care should be
taken to specify no more rangeability than will
actually be required in a particular application.
The orifice plate has traditionally been regarded as
having a maximum rangeability of 3:1 or 4:1. This
comes from the pneumatic transmitter days when the
transmitter limited the measurement range. With a
properly selected orifice and a modern DP
transmitter, a rangeability of 5:1 to as high as 14:1 is
certainly possible. With the 3051SMV and dynamic
compensation, 14:1 rangeability with 0.65% of rate
accuracy can be achieved.
Combining this multivariable rangeability with the
ability to interchange orifice plates, a flow range of
200:1 can be measured without changing the pipe
size or the transmitter!

You might also like