Scribd
Upload
353 views2 pages

Ats-42voc Tech Data

SIL-ACT ATS-42 is a clear, penetrating silane treatment that causes concrete and masonry to repel water and contaminants. It chemically bonds to substrates, forming a penetrated layer below the surface. SIL-ACT ATS-42 has become an industry standard due to its high performance in field and laboratory evaluations. It can be applied by various methods and stores well on job sites.

Uploaded by

alexcus1539
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
353 views2 pages

Ats-42voc Tech Data

SIL-ACT ATS-42 is a clear, penetrating silane treatment that causes concrete and masonry to repel water and contaminants. It chemically bonds to substrates, forming a penetrated layer below the surface. SIL-ACT ATS-42 has become an industry standard due to its high performance in field and laboratory evaluations. It can be applied by various methods and stores well on job sites.

Uploaded by

alexcus1539
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SIL- ACTTM

ATS-42
VOC Compliant

Alkyltrialkoxysilane

HIGH PERFORMANCE
SIL-ACT ATS-42 is a clear, penetrating silane
treatment which causes concrete, masonry and many
natural stones to become repellent to water, chloride
and other waterborne contaminants and weathering
elements. Due to its high performance in long term field
and laboratory evaluations by many independent
agencies, SIL-ACT ATS-42 has become an industry
standard for high performance clear water repellents.

DURABLE
SIL-ACT ATS-42 can be applied to the surface by
low-pressure spray, brush, roller or squeegee. It can be
stored on the jobsite at temperature extremes,
eliminating storage problems associated with emulsified
silane products that can deteriorate on the jobsite, prior
to use, if not properly stored. SIL-ACT ATS-42
chemically bonds with the substrate forming a
penetrated layer below the surface that acts as a oneway filter. Water, chloride and other waterborne
contaminants are repelled without restricting the
substrates natural vapor permeability.

FLEXIBLE
SIL-ACT ATS-42 is an effective treatment for new
and existing cast-in-place concrete, precast concrete,
prestressed concrete, architectural concrete, brick,
masonry, cementious mortars, stucco and many natural
stones. Structures that can be treated include parking
decks,
bridges,
commercial
buildings,
airport
pavements, highways, cooling towers, stadiums and
many other types of horizontal and vertical structures.

High Performance
Economical

Easy to Use
Deep Penetration

TECHNICAL DATA
Property
Active Ingredient
Specific Gravity
Density
Solids Content
VOC Content
Surface Appearance
Drying Time @ 70 F

Test

ASTM C-642-82

Moisture Vapor Permeability

OHD L-35, ASTM E-96, D-1653


Alberta Transportation and
Utilities (1b)
Alberta Transportation and
Utilities (1b)
Alberta Transportation and
Utilities (1b)
OHD L-34/ NCHRP 244 Series II
NCHRP 244 Series II
NCHRP 244 Series II
NCHRP 244 Series IV
ASTM G-53
NCHRP 244 Series II
ASTM E-96, D-1653

Waterproofing after Abrasion


Alkali Resistance
Depth of Penetration
Reduction in Water Weight Gain
Reduction in Absorbed Chloride
Reduction in Absorbed Chloride
Moisture Vapor Permeability
Resistance of Chloride Ion
Penetration
Freeze-Thaw Scaling Resistance
Surface Absorption Test

Alkyltrialkoxysilane
0.81
6.76 lb/gal
> 40% by weight
< 600 g/L
no change
hour
0.3% 48 hours
0.9% 50 days
100%

Method 24, ASTM D-5095

Moisture Absorption resistance

Waterproofing

ATS-42

AASHTO T-259/T-260
ASTM C-672-84
RILEM II.4

85.6%
82.7%
76.1%
0.30 in, 7.5 mm
88%
82%
99%
100%
0.5" Depth <0.2 lb per cubic yard
1.0" Depth <0.0 lb per cubic yard
0 @ 50 cycles
0 inches (10 minutes)

INSTALLATION
1.
Test a small area prior to general application to ensure compatibility, desired results and coverage rates.
2.
Treatment is most effective when the surface to be treated is clean and dry. Remove dirt, dust, oil, grease, curing
compounds, coatings, and other surface contaminants. Water blasting, sandblasting, or shotblasting may be required.
3.
Do not proceed unless surface and air temperature is between 40 F and 110 F. Do not apply if frost, ice, or standing water
are visible on the surface to be treated.
4.
Protect windows, metals, etc. from overspray. If necessary, immediately clean overspray with a clean dry cloth, soap and
water or alcohol. Protect plants and vegetation from overspray.
5.
Spray, brush or roll SIL-ACT ATS-42 treatment on surface to be treated at the recommended application rate. Contact
TM
your SIL-ACT representative for details.
6.
Apply to saturation. Allow spraying dispersion at low pressure, if necessary follow with broom or squeegee for even
distribution.
7.
Normal coverage rate is approximately 125 to 200 square feet per gallon.
8.
Clean equipment with alcohol or suitable solvent.
9.
Partially used containers should be properly sealed and protected from contamination by water or other foreign
substances.

WARRANTY
TM

Limited warranties are available for all SIL-ACT products. Contact ACT or your local SIL-ACT
TM
SIL-ACT ATS-42 is covered by several patents including U.S. 4,931,319.
Advanced Chemical Technologies, Inc.
100 West Wilshire Blvd., Suite C-1
Oklahoma City, OK 73116
(800) 535-0433 (405) 843-2585 (405) 843-2596
www.advchemtech.com

TM

representative for details.

NOTICE This brochure was prepared as an introduction to a product manufactured by Advanced Chemical Technologies, Inc. The information provided herein is based
upon typical installation conditions and is believed to be reliable. However, due to the wide variety of possible intervening factors, Advanced chemical Technologies, Inc.
does not warrant the expected results to be obtained. Details concerning product specifications and warranty may be obtained from Advanced Chemical Technologies,
Inc. Specifications are subject to change. Sale of subject system is limited to Advanced Chemical Technologies, Inc. and authorized applicators conditions of sale
including those limiting warranties and remedies.
ACT 2002

You might also like