APCOTIDE 1000
Two component, high build, high solid engineered epoxy coating
High performance anti-corrosive coating designed for protection of
steelwork in highly aggressive environment
Designed as a barrier coat to provide extended service life in one coat
application on blast cleaned surface
Fast curing and able to cure under water; recommended as a
maintenance coating for offshore splash zone areas
Can be applied upto 500 microns in a single coat application
Excellent mechanical properties
Excellent anti-corrosive property & cathodic disbondment resistance
TECHNICAL DATA
Colour
Off white & Greys, other select shades on request
Gloss
Glossy
Volume Solids
Approx. 87 %
Drying time at 30o C
Surface dry : 2 hours
Hard dry : 8 hours
Full cure : 7 days
Over coating Interval at 30o C
Min. : 8 hours
Max. : 5 days
Shelf Life (cool and dry place)
At least 12 months
Recommended DFT/ Coat 250 - 500 microns
Theoretical covering
Capacity
3.5 sq. mtr/ l @ 250 microns DFT
1.7 sq. mtr/ l @ 500 microns DFT
Flash point
Base
: Not below 28o C
Hardener : Not below 28o C
DIRECTIONS FOR USE
SURFACE PREPARATION & SUBSTRATE CONDITION:
Steel; blast clean to Sa 3/ 2.5 of Swedish specification
Surface profile of 50 - 75 microns is recommended
Surface should be dry & free from all surface contamination
Substrate temperature should be at least 30o C above dew point but not above 50o C
MIXING
Stir the base and hardener separately. If settling is observed in the base, loosen the settled material with the help of hand stirrer followed by power driven stirrer for
quick homogenous mixing. Mix hardener gradually into the base under continuous stirring.
Mixing Ratio
Base : Hardener
Pot life at 30o C
1 hour
(by volume)
4 : 1
Note: In case of part mixing (which should be avoided), close the lids of containers tightly to avoid contact with atmospheric moisture.
Note :
APPLICATION
Application Method
Brush
Airless Spray
Recommended thinner
Volume of thinner
T - 121/ T - 141
T - 121/ T - 141
0 - 10 %
0 - 15%
Nozzle orifice
0.53 - 0.66 mm
20 - 24 MPa
(= approx. 200 - 240 atm;
Nozzle pressure
Maximum film build is best attained by airless spray
Typically 100-150 microns can be achieved by brush application. Multiple coats will be
required to achieve the total specified dry film thickness by brush application
Air Spray (Pressure Pot) can be used, but may require a multiple cross spray pattern
to attain maximum film build
As common to all epoxy, the product will chalk and discolour on exterior exposure.
However these phenomenon are not detrimental to anti-corrosive performance
For requirement of exterior durability with good gloss and colour retention, overcoat
with recommended topcoats
2800 - 3400 p.s.i.)
STORAGE & PACKING
Storage : Store in a cool, dry place. Store in accordance with local regulations.
Packing : 20 litres
SAFETY INFORMATION
As a general safety measure, inhalation of solvent vapours or paint mist and contact of liquid paint with skin & eyes should be avoided. Forced ventilation should be
provided when applying paint in confined spaces or stagnant air. Even when ventilation is provided, respiratory, skin and eye protection are always recommended when
spraying paint.
Please refer our Material Safety Data Sheet prior to using the product.
Disclaimer:To the best of our knowledge the information provided herein are true and accurate at the date of issuance. Since we have no control over the quality or condition of the substrate or the various
factors affecting the use and application of the product, we do not accept any responsibility or liability arising out of use of the product.
The company reserves the right to modify data contained herein without prior notice. Any change in data would normally be followed by issue of a new data-sheet. The user should check with the nearest
sales office of the company and confirm the validity of the information, prior to using the product.
Regd. Office: Asian Paints Ltd., 6 A, Shanti Nagar, Santacruz (E), Mumbai - 400 055, India.
Tel: 022 - 39818000, Fax: 022 - 39818888, E-mail: customercare@asianpaints.com, Website: www.asianpaints.com
February 2009
Product Information Sheet - PC 2782
