Heating Hot water Renewables

ELECTRIC WATER HEATERS

EUROPRISMA
PICCOLO
EUREKA
WALL-HUNG
CLASSICO HE
AQUABRAVO

Products designed to suit a w

from the World No.1 in Water

We all need hot water for washing and cleaning, and the Ariston range of small
water heaters is proof of this, just take a look at some of the places where Ariston
products are used:

Loft Conversions

Warehouses

Cloakrooms

Doctors and Dentists Surgeries

Utility Rooms

Airports

Cafes

Building Sites

Small Industrial Units

As you can see Ariston have a range of products that are trusted to easily and
economically fit into any situation, from the 5 litre Piccolo to the 30 litre
Europrisma.

Scan here with a smart phone to see

the Europrisma being installed...

wide range of applications

r Heating

unvented single installation

If you want your hot water at

mains pressure, then any of the
water heaters can easily be
connected to your incoming cold
water main. Or, if your cold
water comes from a storage
tank, then the Eureka and
Piccolo are ideally suited for
connection to a gravity fed
system.

Mains Cold Feed

unvented multiple installation

It is important to note that the

larger 30 litre Europrisma is
subject to the requirements of
Building Regulations and must
be fitted by a fully qualified
Competent Person who holds
the necessary certification.
Unvented units of 15 litres and
under are not subject to the
same regulations but should
however only be fitted by a
suitably trained person.
In addition to the above units,
Ariston also has a complete
range of larger unvented
cylinders (80 litres to 500 litres),
which are suitable for all
domestic and light commercial
applications.

Mains Cold Feed

open outlet installation

These innovative and easily

installed products are detailed in
the Ariston Unvented Cylinder
literature.
If you require further technical
advice or information, our highly
experienced technical advisors
can be contacted on 0333 240
7777. Should you wish to achieve
Competent Person status then
Ariston run training courses at
various centres nationwide.
Our Training Co-ordinator can
be contacted on 01494 755672.

Mains Cold Feed

The Europrisma 10 and 15 litre capacity units can be installed in a number of ways.
The following guidelines are designed to help select the correct method prior to installation.

Is the unit over 15 litres?

YES

NO
Will the inlet pipework accomodate the expanded water
without the hot water entering any supply pipe connected
to the cold water draw-off? (Fig.1. Page 5)

YES
NO
Do any check valve, stop taps with loose
jumpers or devices that prevent reverse
flow exist in the supply pipework?

YES

NO

Is the mains pressure

> 3.5 bar?

Is the mains pressure

> 3.5 bar?

YES

NO

YES

NO

YES

NO

Install
Kit A +
Kit B + Kit C

Install
Kit A +
Kit C

Install
Kit A +
Kit B + Kit C

Install
Kit A +
Kit C

Install
Kit A +
Kit B + Kit C

Kit C
Recommended

Is the mains pressure

> 3.5 bar?

Length of pipe

EP
10 litre

EP
15 litre

15mm pipe

2.8m

4.2m

22mm pipe

1.5m

2.2m

USING FEED PIPE TO

ACCOMMODATE EXPANSION
Current Water Regulations and
Byelaws permit unvented water
heaters with capacity of 15 litres
or less to accommodate the
expansion of water that occurs
during the heating cycle in the
system pipe work. To achieve this
the pipe work between the nearest
cold water draw off and the water
heater must be of sufficient
volume to accommodate the
expansion.

USING AN EXPANSION KIT

If it is not possible to accommodate
the expansion in the system pipe
work, it is then necessary to use an
expansion vessel and non-return
valve (Kit A).

The discharge from relief valves

must be made in a safe and
conspicuous manner; therefore a
tundish (Kit C) is available for 10
and 15 litre units if required.

USING AN EXPANSION KIT &

PRESSURE REDUCING VALVE
If it is not possible to accommodate
the expansion in the system pipe
work, it is then necessary to use an
expansion vessel and non-return
valve (Kit A). If the mains water
pressure may exceed 3.5 bar a
pressure reducing valve (Kit B)
should also be installed.
The discharge from relief valves
must be made in a safe and
conspicuous manner; therefore a
tundish (Kit C) is available for 10
and 15 litre units if required.

Optional Kit A:
Expansion vessel
and check valve

Optional Kit B:
Pressure reducer with
integral line-strainer

Optional Kit C:
Tundish for 10
and 15 litre units

The Europrisma EP 30 R is covered by the Building Regulations and it is not permissible to accommodate the expansion
water within the system pipework. Expansion controls must be installed. The EP 30 R is supplied with a tundish as standard.
5

EUROPRISMA

10, 15, 30 LITRES

OVER SINK AND UNDER SINK

WATER HEATERS
I

QUALITY STEEL TANK, WITH EXCLUSIVE

VITREOUS ENAMEL COATING
(GLASS LINING)

REGULATION & SAFETY THERMOSTAT

EXTERNAL TEMPERATURE CONTROL

HEATING INDICATOR LIGHT

SIMPLE INSTALLATION

ENAMELLED
STEEL TANK

TEMPERATURE
REGULATION

3 YEAR TANK GUARANTEE

(1 YEAR ON ELECTRICAL
COMPONENTS)
ENVIRONMENTALLY SOUND & HIGHLY
EFFICIENT THERMAL INSULATION

ENVIRONMENTALLY
FRIENDLY
INSULATION

EP30 R
ONLY

Technical data - Overall dimensions

Capacity
l
Power
W
Voltage
V
Reheat time (T= 50C)
min.
Max. Working Temp.
C
Heat loss (kWh/24h) 60C
Typical application*
Product Code

EP
10 0R

EP
10 UR

EP
10 UR/2kW

EP
15 OR

EP
15 UR

EP
15 UR/2kW

EP
30 R

10
3000
240
12
80
0.50
D
877066

10
3000
240
12
80
0.67
D
877067

10
2000
240
17
80
0.67
A
877068

15
3000
240
18
80
0.70
C/E/G
877069

15
3000
240
18
80
0.87
C/E/G
877070

15
2000
240
26
80
0.87
B
877071

30
3000
240
36
75
0.90
F/H
877072

B: Low usage 2/3 basins/1 sink; (kitchens,

garages, factories and WCs)
C: Low usage 4/5 basins/2 sinks; (WC blocks)

*Typical application
A: Low usage 1/2 basins/1 sink; (small kitchens,
en suite bathrooms, loft conversions and cloakrooms)

EP
10 0R

EP
10 UR

EP
10 UR/2kW

EP
15 OR

EP
15 UR

EP
15 UR/2kW

EP
30 R

a mm

350

350

350

350

350

350

440

b mm

255

255

255

300

300

300

365

c mm

350

350

350

350

350

350

440

d mm

90

90

90

80

80

80

110

D: Medium usage 2/3 1/2 basins/1 sink

E: Medium usage 2/3 basins/2 sinks
F: Medium usage 4/5 basins/2 sinks

G: Heavy usage 1/2 basins/1 sink

H: Heavy usage 2/3 basins/1 sink

BSP

62

BSP

203

100
a

Cold water inlet G 1/2

Hot water outlet G 1/2

1/2"

BSP

20

1/2"

20

c
203

c
203

100

62

62

150

1/2"

20

d
100

EUREKA
OPEN OUTLET ELECTRIC STORAGE
WATER HEATER
I

OPEN OUTLET - SUITABLE FOR MAINS

OR GRAVITY FEED
MANUFACTURED FROM A CORROSION
PROOF PLASTIC MATERIAL
COMPLETELY RECYCLABLE AND
ECOLOGICALLY SOUND

EXTERNAL TEMPERATURE CONTROL

HEATING INDICATOR LIGHT

IP25D

EQUIPPED WITH DIRECTIONAL SPOUT

ILLUMINATED ON/OFF SWITCH

CERAMIC DISC MIXING VALVE

10 YEAR TANK GUARANTEE (1 YEAR

GUARANTEE ON ELECTRICAL
COMPONENTS)

TEMPERATURE
REGULATION

Technical data - Overall dimensions

EUREKA
Capacity
Power
Voltage
Heating time (T= 50C)
Maximum temperature
Product Code

l
W
V
min.
C

EUREKA

13
2000
240
23
75
410631

a mm

320

b mm

490

c mm

230

d mm

130

Typical application
Low usage 1/2 basins/1 sink; (small kitchens, en suite bathrooms, loft conversions and cloakrooms)

O
1 / 2"

BSP

I
3/8"

BSP

Cold water inlet G 1/2

Hot water outlet G 1/2

PICCOLO
OPEN OUTLET ELECTRIC STORAGE
WATER HEATER
I

OPEN OUTLET - SUITABLE FOR MAINS

OR GRAVITY FEED
MANUFACTURED FROM A CORROSION
PROOF PLASTIC MATERIAL

ILLUMINATED ON/OFF SWITCH

EXTERNAL TEMPERATURE CONTROL

HEATING INDICATOR LIGHT

EQUIPPED WITH DIRECTIONAL SPOUT

IP25D

TEMPERATURE
REGULATION

Technical data - Overall dimensions

PICCOLO
ARKS 5 0
Capacity
Power
Voltage
Heating time (T= 50C)
Maximum temperature
Product Code

l
W
V
min.
C

PICCOLO
ARKS 5 0

5
2000
240
9
85
868871

a mm

251

b mm

385

c mm

174

d mm

270

Typical application
Low usage 1/2 basins/1 sink; (small kitchens, en suite bathrooms, loft conversions and cloakrooms)

9.5
a

62

G 1/2"

100
30

54.5

I
8

Cold water inlet G 1/2

Hot water outlet G 1/2

COMPLETELY RECYCLABLE AND

ECOLOGICALLY SOUND
10 YEAR TANK GUARANTEE (1 YEAR
GUARANTEE ON ELECTRICAL
COMPONENTS)

WALL HUNG

ST 100

WALL-HUNG UNVENTED CYLINDERS

QUALITY STEEL TANK, 12 BAR

PRESSURE TESTED AND EXCLUSIVE
VITREOUS ENAMEL COATING
ENVIRONMENTALLY SOUND AND
HIGHLY EFFICIENT THERMAL
INSULATION

PROTECH ANTI-CORROSION SYSTEM

INTERNAL REGULATION THERMOSTAT

FACTORY FITTED 1/2 T&P RELIEF VALVE

ENAMELLED
STEEL TANK

TEMPERATURE
REGULATION

DUAL POLE THERMAL CUT-OUTS

UNVENTED CONTROL KIT SUPPLIED
WITH CYLINDER

SPACE SAVING WALL FIXING

SIMPLE INSTALLATION

10 YEAR TANK GUARANTEE

(2 YEAR GUARANTEE ON ELECTRICAL
COMPONENTS)

ENVIRONMENTALLY
FRIENDLY
INSULATION

Technical data - Overall dimensions

Model
Product Code

ST 100
893168/406814

ST 100
a mm

530

Nominal capacity

100

Weight empty

kg

41

b mm

230

c mm

750

Weight full

kg

141

Voltage

240

d mm

175

e mm

560

Power

kW

Reheat time (T= 50C)

min.

120

f mm

500

70

g mm

575

h mm

3/4

Max. Working Temp.

Typical application*
**Typical application
A: domestic usage < 2 people (kitchen, bathroom)

CLASSICO HE

STD 125, 150, 210, 300, 500

HIGH EFFICIENCY FLOOR STANDING DIRECT

UNVENTED CYLINDERS
QUALITY STEEL TANK, 12 BAR
PRESSURE TESTED AND EXCLUSIVE
VITREOUS ENAMEL COATING
(GLASS LINING)

ENVIRONMENTALLY SOUND AND

HIGHLY EFFICIENT THERMAL
INSULATION

ALL PLUMBING AND ELECTRICAL

CONNECTIONS WITHIN A 90 ANGLE

MAGNESIUM ANODES TO PROTECT

AGAINST CORROSION

STAINLESS
STEEL TANK

TEMPERATURE
REGULATION

IMMERSION HEATERS SUPPLIED WITH

REGULATION THERMOSTATS AND
DUAL POLE THERMAL CUT-OUTS
FACTORY FITTED 1/2 T&P RELIEF VALVE
UNVENTED CONTROL KIT SUPPLIED
WITH CYLINDER
SIMPLE INSTALLATION
5 YEAR TANK GUARANTEE (2 YEAR
GUARANTEE ON ELECTRICAL
COMPONENTS)

ENVIRONMENTALLY
FRIENDLY
INSULATION

Technical data - Overall dimensions

Model
Product Code
Nominal capacity
l
Weight empty
kg
Weight full
kg
Voltage
V
Power
kW
Reheat time* (T= 45C) h:min.
Reheat time** (T= 45C) h:min.
Max. Working Temp.
C
Typical application***

STD 125 HE
3060267

STD 150 HE
3060268

STD 210 HE
3060269

STD 300 HE
3060270

STD 500 HE
3060275

125
42
167
240
3+3
2:28
1:46
70
D

150
49
199
240
3+3
2:48
2:10
70
E

200
54
254
240
3+3
3:46
3:54
70
F

300
94
394
240
3+3
5:14
4:37
70
G

495
130
625
240/415
6
4:37
3:18
70
H/I

* Based on single heating element 100% capacity ***Typical application

** Based on single heating element 70% capacity D: domestic usage < 3 people (kitchen, shower)
E: domestic usage 3/4 people (kitchen, bathroom + shower)

Classico STD 100-300 HE

STD 125 HE

STD 150 HE

STD 210 HE

STD 300 HE

STD 500 HE

a mm

666

806

956

1199

1390

b mm

763

921

1237

1540

335

c mm

1024

1182

1498

1792

1870

d mm

550

550

550

600

e mm

281

281

281

259

714

H: above average household use

F: domestic usage 4/5 people (kitchen, 2 bathrooms)
G: domestic usage 5 people (kitchen, 2 bathrooms + shower) I: light commercial use

Classico STD 500 HE

795

10

AQUABRAVO

ITD 130, 150, 215, 305

HIGH EFFICIENCY FLOOR STANDING DIRECT

UNVENTED CYLINDERS
I

QUALITY STAINLESS STEEL TANK,

12 BAR PRESSURE TESTED

ENVIRONMENTALLY SOUND AND HIGHLY

EFFICIENT THERMAL INSULATION

I
I

IMMERSION HEATERS SUPPLIED WITH

REGULATION THERMOSTAT AND DUAL
POLE THERMAL CUT-OUT

UNVENTED CONTROL KIT SUPPLIED WITH

CYLINDER
SIMPLE INSTALLATION
25 YEAR TANK GUARANTEE (2 YEAR
GUARANTEE ON ELECTRICAL
COMPONENTS)

OZONE DEPLETION POTENTIAL (ODP) 0

GLOBAL WARMING POTENTIAL (GWP) <5

FACTORY FITTED 1/2 T&P RELIEF VALVE

STAINLESS
STEEL TANK

TEMPERATURE
REGULATION

ENVIRONMENTALLY
FRIENDLY
INSULATION

Technical data - Overall dimensions

Model
Product Code
Nominal capacity
l
Weight empty
kg
Weight full
kg
Voltage
V
Immersion heater rating kW
Reheat time* (T= 45C) h:min.
Reheat time** (T= 45C) h:min.
Max. Working Temp.
C

ITD 130

ITD 150

ITD 215

ITD 305

3060277 (3826503)

3060278 (3826504)

3060281 (3826505)

3060282 (3826506)

127
27
154
240
3+3
2:46
2:03
70

151
30
181
240
3+3
3:18
2:24
70

212
41
253
240
3+3
4:50
3:16
70

300
60
360
240
3+3
7:19
4:56
70

ITD 130

ITD 150

ITD 215

ITD 305

c mm

1003

1131

1530

2074

d mm

981

1109

1508

2052

e mm

768

896

1295

1839

h mm

353

431

802

1307

Typical application***

* Based on single heating element 100% capacity

** Based on single heating element 70% capacity

***Typical application
D: domestic usage < 3 people (kitchen, shower)
E: domestic usage 3/4 people (kitchen, bathroom + shower)

F: domestic usage 4/5 people (kitchen, 2 bathrooms)

G: domestic usage 5 people (kitchen, 2 bathrooms + shower)

11

www.ariston.co.uk

In the interests of our customers, Ariston Thermo UK Limited is continually developing these products to improve both performance and design. We therefore
reserve the right to change specification without prior notice. This brochure is accurate at the date of printing. Consumer statutory rights are not affected.

Ariston Thermo UK Ltd

Ariston Building
Hughenden Avenue
High Wycombe
Bucks HP13 5FT

Fax 01494 459775

Technical Advice & Customer Service

Fax 01494 463066
technical.uk@aristonthermo.com
customer.service.uk@aristonthermo.com
info.uk@aristonthermo.com

Follow us on
Facebook & Twitter
WA 120 LGB - Mar 12 - Printed by Vario Press