File No.

E471457

Technical Data Sheet

Sigma Series DE Meter

The moving iron panel meters, DE 48/72/96/144 are housed in a moulded polycarbonate
cases which are suitable for the measurement of AC currents for frequency range of 15...400Hz and
voltages in the frequency range of 15...100Hz.

Special Features
Scale interchangeability
Near linear scale
Glass lled polycarbonate housing (UL 94 V-0)
Knife edge pointer
Easily replace able glass and bezel

Sigma Series DE Meter

Application
The moving iron panel meters, DE 48/72/96/144 housed in moulded polycarbonate cases are suitable for
the measurement of AC currents for frequency range of 15...400Hz and voltages in the frequency range of
15...100Hz.

Movement
Moving iron movement has pivots of very high hardness.Movement suspended between spring loaded
saphire jewel and silicon jewel.Movement is critically damped by use of silicon oil.

Over Range
Ammeters

2 times nominal current

Applicable Standards

Voltmeters

1.2 times nominal voltage

Nominal case and cutout dimensions DIN IEC 61554

for indicating Electrical instruments

Scale Interchangeability

Interchangeable

Flame retardant & drip proof

As per UL 94 V-0

Scale and pointer for electrical

measuring instruments

DIN 43802

Connections and Terminal markings

DIN 43807

Terminal bolts/leads

DIN 46200/46282

Case details

Safety requirements and protective

measures for Electrical indicating.
instruments and their accessories

DIN 40050,
VDE 0110, VDE 0410
IEC 529, IEC 1010

Case material

Polycarbonate , ame retardant and drip

proof as per UL 94 V-0.

Performance specications for direct

acting indicating analogue electrical
measuring instruments and their
accessories

IEC51/DINEN60051
DIN 43701

Front facia

Glass

Colour of bezel

Black

Environmental conditions

VDE / VDI 3540

Position of use

Vertical

Panel xing

Mounting Clamp

Mounting

Stackable in a single cutout

Panel thickness

< 25 mm

Front frames for indicating

measuring instruments Principle
dimensions

DIN 43718

UL Compatibility

UL 94 V-0

Mechanical Data
Moulded square case suitable for mounting
in Control / switchgear panels Machinery
consoles.

Terminals

Comply with following European directives

2004 / 108 / EC (EMC directive ), 2006 / 95/EC ( low voltage
directive ) & amendment 93/68/EEC, For CE Marking.

Voltmeters and Ammeters

< 30 A

Hexagon studs, M4 screws and

wire clamps E3

Scale and Pointer

Ammeters < 30 A

Threaded studs M6 with Nuts

Ammeters < 60A

Threaded Studs M8 with Nuts

Pointer

Knife - edge pointer

o

Pointer deection

0...90

Scale characteristics

Near Linear above 10%

of nominal full Scale
value

Scale division

Coarse - ne

Scale length

DE 48

www.sifamtinsley.com

Electral Data

DE72

DE 96

DE144

41 mm 63mm

97mm

146mm

Page 1 of 5

Version No. :APMDE/2015/02

Sigma Series DE Meter

Electrical Data

Environmental Conditions

Measured Quantity Power

Consumption

AC Voltage or current

Voltmeters

< 4.5 VA

Ammeters < 15A

< 0.5 VA

Ammeters > 15A

< 0.8 VA

Continuous Overload Capacity

I (acc. to IEC 51)

1.2 times rated voltage /
current.

Short Duration
Voltameters

Ammeters
Enclosure code (IEC 529)

2 times for 0.5 sec : 9 overloads

2 times 5 sec : 1 overloads
10 times for 0.5 sec : 9 overloads
10 times for 5 sec : 1 overload

Climatic Suitability

Climate category II as per IEC 60051

(climatic class 3 according to
VDE/VDI 3540)

Operating Temperature

- 10... + 55 C

Storage temperature

- 25...+65 C

Relative humidity

< 75% annual average, noncondensing

Shock resistance

15 g. for pulse duration 11ms

Vibration resistance

10-55-10Hz for ampli. 0.15mm (1.5g

at50Hz)

Pollution degree

Stackable in a single cutout

Standard Measuring Ranges

IP 52 case
IP 00 for terminals without back cover
IP 20 for terminals with back cover

A.C. Voltage

A.C. Current

6V

100mA

10V

150mA

15V

250mA

25V

400mA

40V

600mA

60V

1A

Reference Conditions

100V

1.5A

Accuracy class

0.5 according to IEC 51/DIN

EN 60051)

120V

2.5A

132V

4A

Ambient temperature

23 C 2C

150V

5A

Position of use

Nominal position 1

250V

6A

Input Waveform

Rated value of measured quantity

sine wave, distortion factor < 5%

400V

10A

Freequency

65Hz

500V

15A

Other Conditions

IEC 51/DIN EN 60051

600V

20A

1000V

25A

for use with PT

40A

.../100 V secondary

50A (except DE 48)

.../110 V secondary

60A (except DE 48)

Insulation class

Group A according to VDE 0110

Rated insulation

DE 48 : 660V DE 72/96 : 1KV

Proof voltage

DE 48 : 2KV DE 72/96 : 3KV

Installation category

> 50 Mohm at 500 V DC

Nominal Range of use

Ambient Temperature

0 ...50 C

Position of use

Vertical 5

Frequency

45 ...65Hz

100A (except DE 48)

External Magnetic Field

At 0.4 kA/m

For use with CT

.../1A secondary
.../5A secondary

www.sifamtinsley.com

Page 2 of 5

Version No. :APMDE/2015/02

Sigma Series Alpha

DE Meter
70

Options

Electrical Connections

Case
Front Facia

Antiglare glass

Color of bezel

Red, yellow, blue, white

Red index pointer

Front adjustable on site

Position of use

on request 15...180

AC Voltage (Direct connected)

11
L1

Dial
Blank dial

12

N(L2)
With initial and end values
marked

AC Current (Direct connected)

Special markings

Numbering/Lettering

Division dials

Basic divisions without

numbering

Color markings/bands

Red or green

Over range

Two, three and ve times over

range

(Ammeters)

Six times over range

11

12

11

12

L1
N(L2)
AC Current (for use on current
Transformer)

k l

Accessories

L1

Safety Terminal Protection

Full sized polycarbonate back cover to provide protection against
accidental contact (hand and ngers) acc.to VDE 0410.

N(L2)

Dimensions

Safety Precautions

I1 x I 2

a 1 x a2

1) Instruments with damaged bezel or glasses must be

disconnected from the mains.
2) Adequate safety clearance must be maintained to control panel
fasteners and to sheet metal housing. If non - insulated
connector wires are used.
3) The back cover must be snapped into place after connector
wires have been clamped for protection against accidental
contact.
4) Bezel, Scale and Glass may only be replaced under voltage free
conditions.
5) Instruments to be used in grounded panel.

www.sifamtinsley.com

Page 3 of 5

Version No. :APMDE/2015/02

Sigma Series DE Meter

Front in mm Nominal Dimensions, mm
a 1x a 2
h
48 x 48
72 x 72
96 x 96

48 x 48
72 x 72
96 x 96

5.5
5.5
5.5

Cutout, mm

Installation Depth Including Terminal (t), mm

I1 x I2
+0.6

Installation Depth Incl. Full back Cover (f), mm

< 30A (M4) 30...60A(M6) 100A (M8)

+0.6

45 x 45
+0.7
+0.7
68 x 68
+0.8
+0.8
92 x 92

54
54
54

72
62
62

66
66

< 30A

30...100A

62.5
62.5
62.5

75(upto 60A)
70
70

Ordering Information- Only For Representative Products

Size: 48 x 48 Ammeter
Part No.

Description

Class

EQ44-V67X2N1CAW0ST

250V, Scale 0 - 250V

CL-1

EQ44-I1112N1CAW0ST

5A, Scale 0-5A

CL-1

EQ44-V68X2N1CAW0ST

300V, Scale 0- 300V

CL-1

EQ44-I1312N1CAW0ST

10A, Scale 0-10A

CL-1

EQ44-V69X2N1CAW0ST

400V, Scale 0 - 400V

CL-1

EQ44-I1412N1CAW0ST

15A, scale 0-15A

CL-1

EQ44-V70X2N1CAW0ST

500V, Scale 0 - 500V

CL-1

EQ44-I1512N1CAW0ST

20A, Scale 0-20A

CL-1

EQ44-V71X2N1CAW0ST

600V, Scale 0 - 600V

CL-1

EQ44-I1612N1CAW0ST

25A, Scale 0-25A

CL-1

EQ44-I1812N1CAW0ST

40A, Scale 0-40A

CL-1

EQ44-I2012N1CAW0ST

60A, Scale 0-60A

CL-1

Description

Class

Size: 72 x 72 Voltmeter
Part No.

Size: 72 x 72 Ammeter
Part No.
EQ74-I11X2N1CAW0ST

5A, Scale 0-5A

CL-1

EQ74-I13X2N1CAW0ST

10A, Scale 0-10A

CL-1

EQ74-I14X2N1CAW0ST

15A, scale 0-15A

CL-1

EQ74-I15X2N1CAW0ST

20A, Scale 0-20A

CL-1

EQ74-I16X2N1CAW0ST

25A, Scale 0-25A

CL-1

EQ74-I18X2N1CAW0ST

40A, Scale 0-40A

CL-1

EQ74-I20X2N1CAW0ST

60A, Scale 0-60A

CL-1

Description

Class

EQ74-V60X2N1CAW0ST

120V, Scale 0 -120V

CL-1

EQ74-V61X2N1CAW0ST

132V, Scale 0 -132V

CL-1

EQ74-V63X2N1CAW0ST

150V, Scale 0 - 150V

CL-1

EQ74-V65X2N1CAW0ST

200V, Scale 0 - 200V

CL-1

EQ74-V66X2N1CAW0ST

230V, Scale 0 - 230V

CL-1

EQ74-V67X2N1CAW0ST

250V, Scale 0 - 250V

CL-1

EQ74-V68X2N1CAW0ST

300V, Scale 0- 300V

CL-1

EQ74-V69X2N1CAW0ST

400V, Scale 0 - 400V

CL-1

EQ74-V70X2N1CAW0ST

500V, Scale 0 - 500V

CL-1

EQ74-V71X2N1CAW0ST

600V, Scale 0 - 600V

CL-1

Size: 96 x 96 Ammeter
Part No.

Description

Size: 96 x 96 Voltmeter

Class

EQ94-I1112N1CAW0ST

5A, Scale 0-5A

CL-1

EQ94-I1312N1CAW0ST

10A, Scale 0-10A

CL-1

EQ94-I1412N1CAW0ST

15A, scale 0-15A

CL-1

EQ94-I1512N1CAW0ST

20A, Scale 0-20A

CL-1

EQ94-I1612N1CAW0ST

25A, Scale 0-25A

CL-1

EQ94-I1812N1CAW0ST

40A, Scale 0-40A

CL-1

EQ94-I2012N1CAW0ST

60A, Scale 0-60A

CL-1

Part No.

Size: 48 x 48 Voltmeter
Part No.

Description

Class

EQ94-V60X2N1CAW0ST

120V, Scale 0 -120V

CL-1

EQ94-V61X2N1CAW0ST

132V, Scale 0 -132V

CL-1

EQ94-V63X2N1CAW0ST

150V, Scale 0 - 150V

CL-1

EQ94-V65X2N1CAW0ST

200V, Scale 0 - 200V

CL-1

EQ94-V66X2N1CAW0ST

230V, Scale 0 - 230V

CL-1

EQ94-V67X2N1CAW0ST

250V, Scale 0 - 250V

CL-1

EQ94-V68X2N1CAW0ST

300V, Scale 0- 300V

CL-1

EQ94-V69X2N1CAW0ST

400V, Scale 0 - 400V

CL-1

Description

Class

EQ44-V60X2N1CAW0ST

120V, Scale 0 -120V

CL-1

EQ94-V70X2N1CAW0ST

500V, Scale 0 - 500V

CL-1

EQ44-V61X2N1CAW0ST

132V, Scale 0 -132V

CL-1

EQ94-V71X2N1CAW0ST

600V, Scale 0 - 600V

CL-1

EQ44-V63X2N1CAW0ST

150V, Scale 0 - 150V

CL-1

EQ44-V65X2N1CAW0ST

200V, Scale 0 - 200V

CL-1

EQ44-V66X2N1CAW0ST

230V, Scale 0 - 230V

CL-1

www.sifamtinsley.com

Page 4 of 5

Version No. :APMDE/2015/02

Sigma Series DE Meter

For more details and product codes, please contact our local ofce
Sifam Tinsley Instrumentation Inc.
3105, Creekside Village Drive,
Suite No. 801, Kennesaw,
Georgia 30144 (USA)
E-mail Id : [email protected]
Web : www.sifamtinsley.com
Contact No. : +1 404 736 4903

www.sifamtinsley.com

Page 5 of 5

Sifam Tinsley Instrumentation Ltd

Unit 1 Warner Drive,
Springwood Industrial Estate
Braintree, Essex, UK, CM72YW
E-mail: [email protected]
Web: www.sifamtinsley.com/uk
Contact: +44(0)1803615139

Version No. :APMDE/2015/02