Document Title
Security Level
CSFB & IRAT
Drive test Case
T01 IRAT Mobility Test..............................................................................................................................
T01-01 CS Fallback to UTRAN.........................................................................................................
2016-11-25
Huawei Proprietary - Restricted Distribution
Page1, Total37
Document Title
1.
Security Level
LTE to UMTS CSFB by using measurement-based PS handover for an idle UE
making a mobile-originated call..........................................................................................
2.
LTE to UMTS CSFB by using measurement-based PS handover for an idle UE
making a mobile-terminated call..........................................................................................
3.
LTE to UMTS CSFB by using measurement-based PS handover for a connected
UE making a mobile-originated call....................................................................................
4.
LTE to UMTS CSFB by using measurement-based PS handover for a connected
UE making a mobile-terminated call.................................................................................
5. LTE to UMTS CSFB by using measurement-based PS handover for LTE UE in idle
mode calling LTE UE in Connected mode 12
6. LTE to UMTS CSFB by using measurement-based PS handover for LTE UE in
connected mode calling LTE UE in Idle mode 14
7.
LTE to UMTS CSFB by using measurement-based redirection for an idle UE
making a mobile-originated call........................................................................................
8.
LTE to UMTS CSFB by using measurement-based redirection for an idle UE
making a mobile-terminated call........................................................................................
9.
LTE to UMTS CSFB by using measurement-based redirection for a connected UE
making a mobile-originated call........................................................................................
10. LTE to UMTS CSFB by using measurement-based redirection for a connected UE
making a mobile-terminated call........................................................................................
11. LTE to UMTS CSFB by using measurement-based redirection for LTE UE in idle
mode calling LTE UE in Connected mode 26
12. LTE to UMTS CSFB by using measurement-based redirection for LTE UE in
connected mode calling LTE UE in Idle mode ..29
T01-02 LTE to UTRAN PS HO & Redirection
2016-11-25
Huawei Proprietary - Restricted Distribution
Page2, Total37
Document Title
Security Level
1. LTE to UMTS PS handover based on coverage with measurement 32
2. LTE to UMTS redirection based on coverage with measurement 34
T01-03 LTE to UTRAN & UTRAN to LTE Reselection
1. LTE to UMTS & UMTS to LTE Reselection based on coverage with measurement 36
1.
IRAT Mobility Test
1.1.1 LOFD-001033 CS Fallback to UTRAN
1. LTE to UMTS CSFB by using measurement-based PS handover for an idle UE
making a mobile-originated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using PS handover when the UE makes a mobile-originated CS call.
Tools:
1 UMTS<E smartphone UE Example: (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example : (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Prerequisites
UE1 is subscribed on the HSS as follows:
2016-11-25
Huawei Proprietary - Restricted Distribution
Page3, Total37
Document Title
Security Level
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on the
related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear in
the S1 tracing result, indicating that the attach
procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing result.
If EPS attach result contained in this message
is combined EPS attach, the attach procedure
is successful.
2. Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
The eNodeB delivers the inter-RAT
measurement configuration to the UE. The UE
performs inter-RAT measurements. If the
signal quality of CELL2 meets the threshold for
reporting event B1, the UE reports event B1 to
the eNodeB. Then, the eNodeB sends a
handover command to the UE.
RRC_MOBIL_FROM_EURAN_CMD message
can be seen in the LTE Uu interface tracing log
and the PS Handover Complete message can
be seen in the RNC Iu interface tracing log
indicate that the UE is handed over to the
UMTS cell to establish CS call.
2016-11-25
Huawei Proprietary - Restricted Distribution
Page4, Total37
Document Title
4. After UE2 rings, answer the CS call.
Security Level
The CS call is successfully established and the
communication is normal.
5. After Call is finished , then make sure
UE1 is disconnected from the UMTS
network and reselected to the LTE
6. Repeat Step 2, 3 ,4 & 5 for 20 times
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call established
in 3G will be consider as drop call due to
CSFB and will be analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
2.
LTE to UMTS CSFB by using measurement-based PS handover for
an idle UE making a mobile-terminated call
Test Preparation
Please backup the configuration of the eNodeB before this test.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-based PS handover when the UE makes a mobile-terminated CS call.
Tools
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
2016-11-25
Huawei Proprietary - Restricted Distribution
Page5, Total37
Document Title
Security Level
Test Count : 20 times
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.
2. Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Enable UE2 to make a CS call to UE1.
Wait for UE1 to ring.
RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
over to the UMTS cell to establish CS call.
4. After UE1 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
5. After Call is finished , then make sure
UE1 is disconnected from the
UMTS network and reselected to
the LTE
2016-11-25
Huawei Proprietary - Restricted Distribution
Page6, Total37
Document Title
Security Level
6. Repeat Step 2 , 3 , 4 & 5
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
3.
LTE to UMTS CSFB by using measurement-based PS handover for
a connected UE making a mobile-originated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-based PS handover when the UE makes a mobile-originated
CS call.
Tools
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
2016-11-25
Huawei Proprietary - Restricted Distribution
Page7, Total37
Document Title
Security Level
Test Count : 20 times
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.
2. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
3. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
over to the UMTS cell to establish CS call.
2016-11-25
Huawei Proprietary - Restricted Distribution
Page8, Total37
Document Title
4. After UE2 rings, answer the CS call.
Security Level
The CS call is successfully established and
the communication is normal.
5. After Call is finished , make sure UE1 is
disconnected from the UMTS
Network and reselected to the LTE
network
6. Repeat Step 2 , 3 , 4 & 5
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
4.
LTE to UMTS CSFB by using measurement-based PS handover for
a connected UE making a mobile-terminated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-based PS handover when the UE makes a mobile-terminated
CS call.
Tools
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
2016-11-25
Huawei Proprietary - Restricted Distribution
Page9, Total37
Document Title
Security Level
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm , SINR>=15dB,
3G RSCP>=-85dBm , Ec/Io>= -10dB)
Test Count : 20 times
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.
2. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
3. Enable UE2 to make a CS call to UE1.
Wait for UE1 to ring.
RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
2016-11-25
Huawei Proprietary - Restricted Distribution
Page10, Total37
Document Title
Security Level
over to the UMTS cell to establish CS call.
4. After UE1 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
5. After Call is finished , make sure UE1 is
disconnected from the UMTS
Network and reselected to the LTE
network
6. Repeat Step 2 , 3 , 4 & 5 for 20 times
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
5.
LTE to UMTS CSFB by using measurement-based PS handover for
LTE UE in idle mode calling LTE UE in Connected mode
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs , One is in
idle mode Calling to lte UE in Connected Mode
Tools
2 UMTS & LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
2016-11-25
Huawei Proprietary - Restricted Distribution
Page11, Total37
Document Title
Security Level
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB
Test Count : 20 times
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 & UE2 so that it
initiates the combined attach
procedure to LTE CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Make Data application to make UE2 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
4. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
2016-11-25
RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
Huawei Proprietary - Restricted Distribution
Page12, Total37
Document Title
Security Level
over to the UMTS cell to establish CS call.
UE1 is successfully PS handover to UMTS
CELL2 to establish a CS call.
UE2 is successfully PS handover to UMTS
CELL2 to establish a CS call.
5. After UE2 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
6. After Call is finished , then make Sure
UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
7. Repeat Step 2, 3 , 4 , 5 & 6 for 20 times
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
6.
LTE to UMTS CSFB by using measurement-based PS handover for
LTE UE in connected mode calling LTE UE in Idle mode
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs , One is in
Connected Calling to lte UE in idle mode
Tools :
2 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
2016-11-25
Huawei Proprietary - Restricted Distribution
Page13, Total37
Document Title
Security Level
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
Test Count : 20 times
Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure
Excepted Result
1. Powers on UE1 & UE2 so that it initiates
the combined attach procedure to
LTE CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE2 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
4. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
2016-11-25
Huawei Proprietary - Restricted Distribution
Page14, Total37
Document Title
Security Level
tracing log indicate that the UE is handed
over to the UMTS cell to establish CS call.
UE1 is successfully PS handover to UMTS
CELL2 to establish a CS call.
UE2 is successfully PS handover to UMTS
CELL2 to establish a CS call.
5. After UE2 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
6. After Call is finished , then make Sure
UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
7. Repeat Step 2 , 3 , 4 , 5 & 6
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
7.
LTE to UMTS CSFB by using measurement-based redirection for an
idle UE making a mobile-originated call
Test Preparation
Please backup configurations before test execution.
Terminal: At least 1 UMTS<E smartphone UE and 1 UMTS smartphone UE
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-beased redirection when the UE makes a mobile-originated CS call.
Tools :
2016-11-25
Huawei Proprietary - Restricted Distribution
Page15, Total37
Document Title
Security Level
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
Procedure
2016-11-25
Excepted Result
Huawei Proprietary - Restricted Distribution
Page16, Total37
Document Title
1.
Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
Security Level
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2.
Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3.
Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
4.
After UE2 rings, answer the CS call.
5.
After Call is finished , then make sure
UE1 is disconnected from the UMTS
network and reselected to the LTE
6.
Repeat Step 2, 3 ,4 & 5 for 20 times
OutPut:
The CS call is successfully established and
the communication is normal.
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
2016-11-25
Huawei Proprietary - Restricted Distribution
Page17, Total37
Document Title
Security Level
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
2016-11-25
Huawei Proprietary - Restricted Distribution
Page18, Total37
Document Title
Security Level
8.LTE to UMTS CSFB by using measurement-based redirection for
an idle UE making a mobile-terminated call
Test Preparation
Please backup configurations before test execution.
Terminal: At least 1 UMTS<E UE and 1 UMTS UE
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-beased redirection when the UE makes a mobile-terminated CS call.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
2016-11-25
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
Huawei Proprietary - Restricted Distribution
Page19, Total37
Document Title
Security Level
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Enable UE2 to make a CS call to UE1.
Wait for UE1 to ring.
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
4. After UE1 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
5. After Call is finished , then make sure
UE1 is disconnected from the
UMTS network and reselected to
the LTE
6. Repeat Step 2 , 3 , 4 & 5
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
2016-11-25
Huawei Proprietary - Restricted Distribution
Page20, Total37
Document Title
Security Level
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
2016-11-25
Huawei Proprietary - Restricted Distribution
Page21, Total37
Document Title
9.
Security Level
LTE to UMTS CSFB by using measurement-based redirection for a
connected UE making a mobile-originated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-beased redirection when the UE makes a mobile-originated CS
call.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
Procedure
Excepted Result
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
2016-11-25
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
Huawei Proprietary - Restricted Distribution
Page22, Total37
Document Title
Security Level
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
1. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
2. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
3. After UE2 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
4. After Call is finished , make sure UE1 is
disconnected from the UMTS
Network and reselected to the LTE
network
5. Repeat Step 2 , 3 , 4 & 5
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
2016-11-25
Huawei Proprietary - Restricted Distribution
Page23, Total37
Document Title
Security Level
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
7.
LTE to UMTS CSFB by using measurement-based redirection for a
connected UE making a mobile-terminated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-beased redirection when the UE makes a mobile-terminated CS
call.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
Procedure
2016-11-25
Excepted Result
Huawei Proprietary - Restricted Distribution
Page24, Total37
Document Title
1. Powers on UE1 so that it initiates the
combined attach procedure to LTE
CELL1.
Security Level
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
3. Enable UE2 to make a CS call to UE1.
Wait for UE1 to ring.
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
4. fter UE1 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
5. After Call is finished , make sure UE1 is
disconnected from the UMTS
Network and reselected to the LTE
network
6. Repeat Step 2 , 3 , 4 & 5 for 20 times
OutPut:
2016-11-25
Monitor the S1 & UU trace
Huawei Proprietary - Restricted Distribution
Page25, Total37
Document Title
Security Level
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
8.
LTE to UMTS CSFB by using measurement-based redirection for
LTE UE in idle mode calling LTE UE in Connected mode
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs by using
measurement-beased redirection when LTE UE in idle mode calling LTE UE in Connected
mode
Tools :
2 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 and UE2 are subscribed on the HSS as follows:
QCI (by default), = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
Test Count : 20 times
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
2016-11-25
Huawei Proprietary - Restricted Distribution
Page26, Total37
Document Title
Procedure
Security Level
Excepted Result
1. Powers on UE1 & UE2 so that it initiates
the combined attach procedure to
LTE CELL1.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE1 is in idle
mode.
3. Make Data application to make
UE2 in Connected mode
Enable UE1 to make a CS call to UE2. Wait
for UE2 to ring.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
Open streaming website or do any data
application to make UE in connected mode
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
UE2 is successfully redirected to UMTS
CELL2 to establish a CS call.
After UE2 rings, answer the CS call.
2016-11-25
The CS call is successfully established and
Huawei Proprietary - Restricted Distribution
Page27, Total37
Document Title
Security Level
the communication is normal.
3. After Call is finished , then make Sure
UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
4. Repeat Step 2, 3 , 4 , 5 & 6 for 20 times
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
2016-11-25
Huawei Proprietary - Restricted Distribution
Page28, Total37
Document Title
9.
Security Level
LTE to UMTS CSFB by using measurement-based redirection for
LTE UE in connected mode calling LTE UE in Idle mode
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for This test case aims to
verify that the eNodeB performs CS fallback for 2 LTE UEs by using measurement-beased
redirection when LTE UE in Connected mode calling LTE UE in idle mode
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 and UE2 are subscribed on the HSS as follows:
QCI = 9(by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB
Test Count : 20 times
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
Procedure
Excepted Result
1. Powers on UE1 & UE2 so that it initiates
the combined attach procedure to
LTE CELL1.
2016-11-25
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
Huawei Proprietary - Restricted Distribution
Page29, Total37
Document Title
Security Level
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE2 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Make Data application to make UE1 in
Connected mode
Open streaming website or do any data
application to make UE in connected mode
4. Enable UE1 to make a CS call to UE2.
Wait for UE2 to ring.
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
UE2 is successfully redirected to UMTS
CELL2 to establish a CS call.
5. After UE2 rings, answer the CS call.
The CS call is successfully established and
the communication is normal.
6. After Call is finished , then make Sure
UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
2016-11-25
Huawei Proprietary - Restricted Distribution
Page30, Total37
Document Title
Security Level
7. Repeat Step 2 , 3 , 4 , 5 & 6
OutPut:
Monitor the S1 & UU trace
CSSR, Call setup time and DCR (only the call
dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour
2016-11-25
Huawei Proprietary - Restricted Distribution
Page31, Total37
Document Title
Security Level
T01-02 L2U IRAT
.1
LTE to UMTS PS handover based on coverage with measurement
Objective
This test case aims to verify that the eNodeB supports inter-RAT PS handovers due to
coverage changes.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
Perform downlink data transmission from the FTP Server ,Select One Point at the LTE Cell
edge at RSRP<= -110 , then Start to move from the lte coverage to the UMTS Coverage till
Handover occur from LTE to UMTS
Test Count : 20 times
Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure
Expected Result
Power on the UE so that it initiates the attach
procedure.
The UE attaches to CELL1.
Use FTP tool or Iperf to perform downlink
data transmission.
Data is transmitted properly.
Enable the UE to leave the LTE cell and
approach the UMTS cell until a
handover is triggered.
The UE reports event A2 to the eNodeB. After
receiving the report, the eNodeB delivers the
inter-RAT measurement configuration to the
UE. The UE performs inter-RAT
measurements. If the signal quality of the
UMTS cell meets the threshold for reporting
event B1, the UE reports event B1 to the
2016-11-25
Huawei Proprietary - Restricted Distribution
Page32, Total37
Document Title
Security Level
eNodeB. Then, the eNodeB sends a
handover command to the UE.
The RRC_MOBIL_FROM_EURAN_CMD
message in the LTE Uu interface tracing log
and the Handover to UTRAN Complete in Uu
interface and PS Handover Complete
messages in the RNC Iu interface tracing log
indicate that the UE is handed over to the
UMTS cell.
The data transmission in UMTS side is
normal.
Disconnect the UE and save the logs.
Output :
Operation succeeded.
-
Monitor the S1 & UU trace
Inter-RAT Handover Success Rate
Time Latency
2016-11-25
Huawei Proprietary - Restricted Distribution
Page33, Total37
Document Title
.2
Security Level
LTE to UMTS redirection based on coverage with measurement
Objective
This test case aims to verify that the eNodeB supports inter-RAT redirections due to coverage
changes.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
Perform downlink data transmission from the FTP Server ,Select One Point at the LTE Cell
edge at RSRP<= -110 , then Start to move from the lte coverage to the UMTS Coverage till
Redirection occur from LTE to UMTS
Test Count : 20 times
Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure
Expected Result
Power on the UE so that it initiates the attach
procedure.
The messages INITIAL UE MSG and the last
UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE attaches to CELL1.
Use FTP tool or Iperf to perform downlink
data transmission.
Data is transmitted properly.
Enable the UE to leave the LTE cell and
approach the UMTS cell until a
redirection is triggered.
The UE reports event A2 to the eNodeB. After
receiving the report, the eNodeB delivers the
inter-RAT measurement configuration to the
UE. The UE performs inter-RAT
2016-11-25
Huawei Proprietary - Restricted Distribution
Page34, Total37
Document Title
Security Level
measurements. If the signal quality of the
UMTS cell meets the threshold for reporting
event B1, the UE reports event B1 to the
eNodeB. Then, the eNodeB sends a
redirection command to the UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface indicates that the redirection is
triggered successfully.
The Routing Area Update Request message
in the Initial UE message on the Iu interface
indicates that the redirection procedure is
successful.
The data transmission in UMTS side is
normal.
Disconnect the UE and save the logs.
Output:
Operation succeeded.
-
Monitor the S1 & UU trace
Redirection Attempt Success Rate
Time Latency
2016-11-25
Huawei Proprietary - Restricted Distribution
Page35, Total37
Document Title
Security Level
T01-03 LTE to UTRAN & UTRAN to LTE Reselection
1. LTE to UMTS & UMTS to LTE Reselction based on coverage with
measurement
Objective
This test case aims to verify that the eNodeB supports reselection due to coverage changes.
Tools :
1 UMTS<E smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
Make Sure UE are in idle mode , then Select One Point at the LTE Cell edge at RSRP<= -110 ,
then Start to move from the lte coverage to the UMTS Coverage till reselection from LTE to
UMTS occur , then return back from the UMTS Coverage to the LTE Coverage till reselection
from UMTS to LTE is done
Test Count : 20 times
Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure
Expected Result
1. Power on the UE so that it initiates
the attach procedure.
The UE attaches to CELL1.
2. Wait 10s and verify that UE1 is in idle
mode.
The message RRC Connection Release
indicates that UE1 has entered idle mode.
3. Enable the UE to leave the LTE cell
and approach the UMTS cell until a
reselection is happened
4. Return back moving from the UMTS
towards the LTE Coverage , till
Reselection from UMTS to LTE is
happened
2016-11-25
Huawei Proprietary - Restricted Distribution
Page36, Total37
Document Title
Security Level
5. Repeat Step 2 , 4 & 4 for 20 times
Output :
Time Latency
2016-11-25
Huawei Proprietary - Restricted Distribution
Page37, Total37
