Scribd
Upload
332 views4 pages

S KEVCY 24 AE

The document summarizes ABB's new Bushing Combi Sensors that are designed for medium voltage systems. The sensors have several technical and economic benefits over conventional instrument transformers. Technically, they have an extensive dynamic range, are non-saturable for accuracy, and provide high accuracy with very low power requirements. Economically, they are much smaller and lighter to install, require less engineering and logistics due to their wide range, and use less raw materials. The sensors measure both current and voltage through a Rogowski coil and capacitive voltage divider respectively, and provide proportional output signals for monitoring and protection devices.

Uploaded by

Mahyar Mashayekhi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
332 views4 pages

S KEVCY 24 AE

The document summarizes ABB's new Bushing Combi Sensors that are designed for medium voltage systems. The sensors have several technical and economic benefits over conventional instrument transformers. Technically, they have an extensive dynamic range, are non-saturable for accuracy, and provide high accuracy with very low power requirements. Economically, they are much smaller and lighter to install, require less engineering and logistics due to their wide range, and use less raw materials. The sensors measure both current and voltage through a Rogowski coil and capacitive voltage divider respectively, and provide proportional output signals for monitoring and protection devices.

Uploaded by

Mahyar Mashayekhi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Bushing Combi Sensors

Sensors - New detectors


in medium voltage system
General
Conventional instrument transformers have been widely
used in medium voltage networks for transforming high
currents and voltages to a level suitable for measuring
and protection. The instrument transformers have been
dimensioned according to the requirements of the measuring equipment and protection relays.

The level of the input signal to the new measuring and


protection system has been significantly reduced compared to the level for conventional systems. Due to this
ABB has introduced a range of sensors. The sensors
fulfil in an optimal way the requirements of the different
functions in the new digital secondary equipment.

The introduction of new digital technology for measuring and protection in medium voltage system has
changed the demands of the detectors.

Technical benefits
Extensive dynamic range
In medium voltage systems upto 24 kV, it is possible,
with only one type to cover the whole scope of current
and voltage sensors for measuring and protection.

Non-saturable

High degree of accuracy


The sensors are designed for the smaller power requirements of digital secondary equipment. Instead of
a typical burden of a conventional transformer, 15 VA
and more, the sensor delivers the signal with a burden
of only a fraction of a VA.

Relative output voltage

No ferromagnetic cores are used in the sensors. This


means that the sensors are immune to any risk of
saturation and are linear over the whole measuring
range.

Economical benefits

Primary current / In

Small in volume and weight

Simplified engineering and logistics

The sensors are much smaller in volume and weight


compared to coneventional instrument transfomers.
These benefits are used to full advantage in new constructions of medium voltage switchgear.

As mentioned above the sensors have an extensive


dynamic range compared to conventional instrument
transformers. Due on this only one type of sensors is
needed. This means that we can offer very simple
engineering and logistics.

Environmentaly friendly
technology
The construction of the sensors means that much less
raw material is needed. This means that the sensors
are a step into more environmentaly frindly technology.

Description

Technical Data

The current sensor is based on the principle of the


Rogowski-coil. The sensor consists of an air-core winding, immune to any risk of saturation as it has no
ferromagnetic core. It is linear over the whole measuring range. The output signal is a voltage, which
is proportional to the derivative of the current. A digital
integration of this voltage is carried out and gives the
measured current.

Current Sensor
Primary current
Rated output voltage
Rated frequency
Temperature range
Accuracy
Short circuit
Withstand current

The voltage sensor is based on the capacitive voltage


divider. Also this sensor is non-saturable and linear
over the whole measuring range. The output signal is
a voltage, which is directly pro-portional to the primary
voltage.

upto 1250 A
150 mV (50 Hz)
50, 60 Hz
-40....+70 oC
Class 1
31,5 / 80 kA

Voltage Sensor

A coupling capacitor is included.

Type
Bushing Combi Sensor, type KEVCY 24 AE1.

Rated voltage
Insulation level
Division ratio
Rated frequency
Temperature range
Accuracy

upto 24 kV
50 / 125 kV
10.000 / 1
50, 60 Hz
-40....+70 oC
Class 3 / 3P

Weight

9.0 kg

70
67,5

P1

Ck / BNC

Ck

25

203

357 1

402 1

90

30

Cable,length 4m
07
O

30
1,5

S2/n

0
-0,15

S1/a
M 16

P2

Twin-BNC
148
120 1

89

11

EN 50181
TYPE C
176,5 1

40

Rating plate

Weight 9 kg

Length of cable 4.0 m


Dimension drawing, 135 KEVCY 1

Tel.: +420 547 152 602


+420 547 152 604
Fax: +420 547 152 626

1VLC000577 Rev-, en 2003.05.20

ABB s.r.o.
org. unit EJF
Vdesk 117
619 00 Brno, Czech Republic
E-mail: [email protected]
http://www.abb.com

You might also like