FS-519 Finisher
INSTALLATION MANUAL
Applied Machines: C353/C253/C203/C353P
COLOR MFP (Color/B&W): 35 ppm/35 ppm, 25 ppm/25 ppm, 20 ppm/20 ppm
COLOR PRT (Color/B&W): 35 ppm/35 ppm
Product Code: A02E
Note: No. Name Shape Qty
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could 6. Right cover
result in personal injury. When transporting the
machine, assign an adequate number of persons 1
to the job and ensure that each person can take a
good position of not being excessively loaded.
(mass: approx. 33 kg (72-3/4 lb)) 9J08IXC007DA
7. Mounting
bracket A
I. Accessory parts 1
No. Name Shape Qty
9J08IXC010DA
1. Finisher unit
8. Mounting
bracket B
1 1
9J08IXC001DA 9J08IXC011DA
2. Tray unit 9. Adjusting plate
9J08IXC012DA
10. Exit tray
1
(upper)
1
4349U015AA
11. Retaining plate
1
4349U016AA
12. Label
A01GIXC050DA
3. Secondary
cover 1
1
9J08IXC088DA
9J08IXC004DB
4. Front cover
* Be sure to keep the adjusting plate, which is used
when the machine is not equipped with the paper
1 feed cabinet and desk.
9J08IXC005DA
5. Connector
cover
1
9J08IXC006DA
A01G-9570-01
E-1
III. Removing protective tape, packing and
No. Name Shape Qty
other shipping materials
13. Screw A
(4 18 mm) <Finisher unit>
8
Note:
9J08IXC075DA
Place the finisher unit beforehand on the table in a
way that the front cover will be off the table.
14. Screw B
(3 8 mm) 2
9J08IXC077DA
15. Screw C
(3 8 mm) 3
9J08IXC078DA
16. Screw D
(4 8 mm) 2
9J08IXC079DA
17. Screw E
(4 8 mm) 1
9J08IXC080DA
A01GIXC003DA
18. Screw F
(3 8 mm) 3
1. Remove the protective sheet and tape from the
9J08IXC081DA
finisher unit.
19. Shoulder screw
2
4582U010AA
20. Installation
manual
1
set
4980IXC019DA
A01GIXC004DA
After unpacking, be sure to get rid of the 2. Remove the front cover (two screws).
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
Note:
When the punch kit and the saddle stitcher are to
be mounted along with the finisher, mount the
punch kit and the creasing unit for the saddle
stitcher to the finisher before mounting the finisher
unit to the machine.
A01GIXC005DA
II. When installing to C353P
This manual provides the illustration of the machine
used as MFP. However, the same installation proce-
dure is used for C353P.
E-2
3. Remove the fixing bracket of the front cover (one 6. Remove the protective layer.
screw). Note:
Take care so that the mylar will not be bent.
Protective layer
Mylar
A01GIXC006DA
9J08IXC019DC
4. Remove protective tape from different parts of the
front cover. 7. Remove the protective tape on the front side of
the finisher unit.
A01GIXC007DA
9J08IXC020DC
5. Remove three fixing brackets on the left side of
the finisher unit (two screws). 8. Remove two screws at the bottom of the finisher
unit, and remove the fixing bracket.
9J08IXC018DD
9J08IXC021DC
E-3
9. Remove the fixing bracket (upper) on the front <Tray unit>
side of the finisher unit (two screws).
1. Raise the box of the tray unit and remove the tray
10. Remove the fixing bracket (lower) on the front
unit from the box.
side of the finisher unit (two screws).
Note:
When removing the tray unit from the box, grasp
the tray unit at the areas as shown in the illustra-
tion below.
9J08IXC022DC
11. Remove the fixing bracket on the right side of
the finisher unit (two screws).
A01GIXC008DA
9J08IXC023DB
A01GIXC051DA
A01GIXC041DB
E-4
Note: 2. Remove protective tape from different parts of the
Set the tray unit upright on the table to conduct tray unit.
operation. Note:
Take care so that the plate spring on the tray Be sure not to remove the stopper until the tray
unit will not be bent. unit is installed into the main unit.
Plate spring
A01GIXC053DA
Stopper
A01GIXC011DD
A01GIXC055DB
E-5
3. Remove the fixing bracket of the tray unit (three IV. Installation procedures
screws each).
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove the sub tray of the machine.
* Remove it while pushing the claws of the sub tray
in the direction of the allow shown on the illus-
tration and unhook.
Screw Screw
A01GIXC013DB
A083IXC006DB
3. Remove the fixing leg and fixing leg cover of the
front left leg only when the paper feed cabinet or
the desk is mounted.
A01GIXC056DA
4. Peel seals off the machine (two seals).
Seal A083IXC007DA
E-6
5. Install the mounting bracket A (four screw As fur- 8. Align the hole of the finisher unit to the positioning
nished with the finisher). pin, then set it all the way in.
Note: Note:
The clearance between the mounting bracket A Set it so that the hole indicated in the illustration
and the machine must parallel. will meet the stabilizing pin.
When carrying the finisher unit, hold the posi-
tions as shown on the illustration.
Stabilizing
pin
A01GIXC057DB
Clearance
A01GIXC058DA
Machine
9. Set the tray unit.
Note:
To set the tray unit, use the area of A as a guide.
Mounting
bracket A
9J08IXC082DB
6. When the punch kit and the saddle stitcher are to
be mounted along with the finisher, mount the
punch kit and the creasing unit for the saddle
stitcher to the finisher.
Note:
For the punch kit and the saddle stitcher mounting
procedures, see installation manual for them.
A01GIXC059DA
7. Remove the job separator (JS-505) if it is
mounted on the machine.
Note:
For the removal procedure, see the installation
manual for the job separator (JS-505).
A01GIXC060DA
E-7
10. Fix the tray unit to the machine (four screw As 14. Remove the locking tape and the tag.
furnished with the finisher).
Note:
Adjust the casters to align the screw holes.
A01GIXC064DA
15. Remove the stopper.
A01GIXC061DA
11. Install the mounting bracket B (two screw Bs
furnished with the finisher).
Note:
Mount it so that the protruding part will face
upward.
Protruding part
A01GIXC065DA
16. Attach the stopper which was removed in step
15 to the position shown in the illustration.
A01GIXC062DA
12. Remove the exit tray mounting holder and install
two shoulder screws furnished with the finisher.
13. Reinstall the exit tray mounting holder that has
been removed in step 12 (one screw).
A01GIXC066DA
A01GIXC063DA
E-8
17. Pull the lock release lever and remove the fin- 19. Install the connector cover (one screw E fur-
isher from the machine. nished with the finisher).
* Fit claws (two points) into the slots first.
A01GIXC067DA
A01GIXC023DB
18. Connect the three connectors and a ground wire
(one screw C furnished with the finisher). 20. Install the secondary cover (two screw Cs fur-
Note: nished with the finisher).
Route the connectors, bundle of harness and Note:
ground wire in a way that one is not placed over Make sure that there is a uniform clearance
the others, and the space indicated with the circle between the misfeed clearing dial and secondary
on the illustration is secured. cover.
Make sure that the ground wire is not routed over
the connectors (illustration A) and the bundles of
harness do not face downward (illustration B).
A A
A01GIXC022DB A A
Screw C
<OK> Bundle of harness
Secondary
cover
Misfeed clearing dial
Connector Screw C
Ground wire
A01GIXC044DA
Illustration A <NG> Illustration B <NG>
A: Clearance A01GIXC070DA
A01GIXC046DA A01GIXC045DA
E-9
21. Install the right cover (two screw Ds furnished 24. Tighten the screws that have been loosened in
with the finisher). step 22.
* Fit claws (three points) into the slots first. 25. Install the band and the retaining plate to the
front cover (one screw F furnished with the fin-
isher).
26. Close the front cover.
A01GIXC071DA
Retaining plate
22. Loosen two screws and move the hinge up.
23. Set the front cover, and move the hinge down to
fix the front cover.
A01GIXC073DA
27. Push the board box all the way to the lock posi-
tion.
28. Set the finisher to the machine.
Hinge
Screw
A01GIXC072DA
Board box
A01GIXC074DA
29. Install the upper exit tray (two screw Fs fur-
nished with the finisher)
Note:
To prevent problems, be sure to securely tighten
the screws.
.
A01GIXC075DA
E-10
30. Connect the hookup cord to the machine. 34. Loosen the two screws (left and right) shown in
the illustration and make the height adjustment.
Then tighten the screws.
A01GIXC081DA
31. Measure the width of X. A01GIXC048DA
Specifications: 5 2 mm
Note: 35. Reinstall the covers that have been removed in
If X is out of the specified range, follow step 32 step 33 (two covers).
and later to adjust the finisher height.
If X is within the specified range, height adjust-
ment is not required. Move to step 37.
A01GIXC049DA
36. Set the finisher to the machine.
A01GIXC077DA
32. Pull the lock release lever and remove the fin-
isher from the machine.
33. Remove a cover from each stand leg (two
places).
A01GIXC047DA
E-11
37. Measure the width of Y and Z (clearance of the 39. Affix the labels to the position shown below.
exterior parts) on front and back side.
<Reverse automatic document feeder>
Specifications:
Y = Z - 1 mm (Y must be smaller than Z)
Z = 7 2 mm (front side)
Z = 9 2 mm (back side)
Note:
To measure the front side, open the front door and
measure it using finisher side as supporting point Label
refer to <Front side measuring method> shown on
the illustration below.
A01GIXC037DA
Y
<by the FD original scale>
A01GIXC078DA
<Front side measuring method>
Label
Y A01GIXC038DA
A01GIXC035DC
38. Lower the left casters until the width of Y and Z
is within the specifications.
* For adjusting the casters, hold the bottom part of
the stand table and turn the adjusting bolt.
Adjusting
Left bolt Right
A01GIXC080DA
E-12
