3 - CURRENT ELECTRICITY Page 1

3.1 Electric Current

1 ampere of electric current is produced when 1 coulomb of electric charge passes through
the cross-section of the conductor in 1 second.

In a steady circuit, electrical potential at all points of a conductor remain constant with
respect to time. In such a steady circuit, the amount of electric charge entering any cross-

om
sectional area of a conductor in a given time interval is equal to the amount of electric
charge leaving that cross-sectional area in the same interval of time. In other words, charge
never accumulates at any point in the conductor. Also the electric charge is neither created
nor destroyed at any point in the conductor. This means that electric charge is conserved.

Let Q amount of electric charge flow through any cross - sectional area of the conductor in

.c
time interval t. The average electric current flowing in time interval t is given by

Q
< > =

ce
t

The instantaneous electric current at time t is given by

= lim
t 0
Q
t
=
dQ
dt ra
m
Electric current is a fundamental quantity in S.I. unit and its symbol is A meaning ampere.
3 6
Smaller units of the current are milliampere ( mA = 10 A ) and microampere ( A = 10 A ).

Current density
xa

The electric current density near any point is defined as the amount of electric current
flowing perpendicularly through the unit cross - sectional area near that point.

.e

Let J be the electric current density at every point

on the cross - sectional area,
P be some point of the curved cross - sectional area
of the conductor as shown in the figure,
w

a be the area vector of the surface near point P,
component of which in the direction of the
w

current is a cos , where

is the angle between the area vector and the
direction of the current.
w

Therefore, average current density near point P,

< J > = where is electric current flowing through the small area element near
a cos
point P.

Therefore, electric current density,

d
J = lim = d = J da cos = J . da
a 0 a cos da cos
 3 - CURRENT ELECTRICITY Page 2

Integrating,

= d = J . da = J da = JA
a

J = where A = the entire cross - sectional area
A

om
3.2 Electromotive Force and Terminal Voltage
The potential difference between the two poles of an electric cell is defined as the work done
by the non-electrical force ( due to chemical process taking place inside the cell ) in moving a
unit positive electric charge from a negative pole towards the positive pole.

.c
The energy gained by the unit positive charge due to the non-electrical force, in moving it
from the negative pole towards the positive pole, is called the emf ( electromotive force ) of
the electric cell. Its unit is joule / coulomb ( = volt ).

ce
When the poles of the electric cell are connected externally by a conducting wire, current
starts flowing in the circuit. The direction of the conventional current is from the positive pole
to the negative pole of the cell in the conducting wire. Actually, electrons move from the

ra
negative pole to the positive pole of the cell in the conducting wire. Inside the cell, current is
due to the movement of positive ions towards the positive pole and negative ions towards
the negative pole of the cell. During the motion inside the cell, the charges have to overcome
the resistance offered by the materials of the cell. This resistance is called the internal
m
resistance, r, of the cell. Some of the energy gained by the positive charge due to the work
done by the non-electrical force is dissipated as heat in overcoming the internal resistance of
the cell. This reduces its overall energy in comparison with open circuit condition. Hence, the
p.d. between the poles of the cell is slightly lower when current is flowing as compared to
xa

the open circuit condition. This reduced p.d. is called the terminal voltage of the cell.

The relation between the emf ( ) and the terminal voltage ( V ) is

- r
.e

V =

3.3 ( a ) Ohms Law

w

The ratio of the potential difference ( V ) between the two ends of the conductor, kept in a
fixed physical condition, and the electric current ( ) flowing through it is constant. This
statement is called Ohms Law. This ratio is called the resistance ( R ) of the conductor. Its
w

unit is ohm and symbol is .

V ( volt )
w

R ( ohm ) =
( ampere )

1 / R is called the conductance of the material.

Its unit is mho and symbol .

Metals, some insulators and many electrical

components obey Ohms law to perfection, but
not all materials. The graph of vs. V will be
a straight line for a conductor obeying Ohms
law at a constant temperature, but the resistance
of the conductor changes with temperature.
 3 - CURRENT ELECTRICITY Page 3

3.3 ( b ) Resistivity
Resistance ( R ) of a conductor varies directly as its length ( l ) and inversely as its cross -
sectional area ( A ) at a given temperature.

1 l
R l and R R =
A
A

om
where the constant is known as the resistivity of the material. Its value depends on the
type, temperature and the pressure existing on the given conductor. Its unit is ohm-meter
( m ).

Resistivity of the material of a conductor at a given temperature and pressure is defined as

.c
its resistance per unit length per unit cross-sectional area.

1 1
Conductivity is the inverse of resistivity. Its unit is mho-m ( or siemen - m ) and its symbol

ce
1
is ( = m ).

3.3 ( c ) Colour Code for Carbon Resistors

ra
There are two types of resistors: ( i ) wire wound and ( ii ) carbon resistors. Wire wound
resistors are made of manganine, constantan and nichrome wires wound on a proper base.
Carbon resistors are small, cheap and widely used in electronic circuits.
m
n n
Colour Digit 10 Colour Digit 10 Tolerance

0 7
Black 0 10 Violet 7 10
xa

1 8
Brown 1 10 Grey 8 10
2 9
Red 2 10 White 9 10
3
Orange 3 10
4 1
Yellow 4 10 Gold 10 5%
.e

5 2
Green 5 10 Silver 10 10 %
6
Blue 6 10 No colour 20 %
w

Slogan to memorize colour code - B B ROY Goes to Bombay Via Gate-Way

w

The value of the carbon resistor can be known from the colour bands on it. Refer to the
above figure and the table.
w

The first band yellow has number 4 and the second band violet has number 7. This forms
1
number 47. The third band brown means 10 as read from the third column of the table.
1
47 10 gives 470 as the value of the resistor. The last band of golden colour gives
tolerance of 5 %. Thus, true value of the resistor will be 470 5 % .

3.4 Origin of Resistivity

In vacuum, electrons have accelerated motion due to electric field. Contrary to this, electrons
move with some average velocity due to electric field in a conductor under steady state of
the flow of the current.
 3 - CURRENT ELECTRICITY Page 4

Outer orbit electrons of metals ( known as valence electrons ) are called free electrons as
they are free to move in the entire space occupied by the piece of metal. The positively
charged ions left behind oscillate about their lattice positions with energy depending upon
temperature of metals. The free electrons move randomly in the space between the ions. In
the absence of any electric field, the average number of electrons crossing any cross-section
of a conductor being zero, there is no current. When potential difference is applied between
the two ends of the conductor, electrons are dragged towards the positive end. If E is the

om
electric field along the length of the conductor, an electron experiences a force eE opposite
to the direction of the electric field as it is negatively charged and starts moving with an
acceleration, a = eE / m. During this motion, electrons collide with constantly oscillating
positive ions. With every such collision, they become almost stationary and start their motion
again from zero velocity. The net result is that they move with some average velocity known
as drift velocity, vd, resulting in current.

.c
If is the average time ( known as relaxation time ) between two successive collisions of the
electron with the ions, then

ce
eE
vd = ... ( 1 )
m

ra
Now, the current density J is directly proportional to E.
is called the conductivity of the material of conductor.
J E J = E ... ( 2 )
m
Calculating J :

If N = number of electrons crossing unit cross-sectional area of the conductor in 1 s, then

xa

J = Ne = n e vd ... ( 3 )
where n = number of free electrons per unit volume of the conductor = N / vd

Putting the values of J and vd from equations ( 2 ) and ( 1 ) in equation ( 3 ), we have

.e

eE
2

1 ne m
E = ne = = = ... ( 4 )
ne
m 2
w

With increase of temperature, ions oscillate faster resulting in decrease in relaxation time, ,
w

and increase in resistivity, .

Vectorially, J = nq v d . If q is positive, then J and v d will have the same direction and
w

if q is negative, then they will have opposite directions.

3.4 ( a ) Mobility
The conductivity of any material is due to mobile charge carriers which can be electrons in a
conductor or electrons and ions produced by ionization of air molecules or the positive and
negative ions in electrolytes. In semi-conductors, electrons and holes ( hole is the deficiency
of electron in the covalent bond which behaves as a positively charged particle ) are
responsible for the flow of current.
 3 - CURRENT ELECTRICITY Page 5

Mobility, , of a charged particle is defined as its drift velocity per unit electric field
intensity.
vd
Thus, =
E
vd
From equation, nevd = E for an electron moving in a conductor, we have = .
E ne

om

= , where is the conductivity and n is the number of free electrons / unit volume.
ne

Thus, for an electron, e = n e e e and similarly for holes = n e .

h h h

.c
In a semi-conductor, the holes and electrons both constitute current in the same direction.

Hence, total conductivity,

ce
= e + h = n e e e + nh e h

3.5 Temperature Dependence of Resistivity

= where,
ra
The resistivity of metallic conductors increases with temperature as under.

0 [ 1 + ( - 0 ) ] 0 = resistivity at some reference temperature 0

m
= resisitivity at temperature and
= temperature coefficient of resistivity and its unit is ( C ) 1.
xa

( Note: Actually, the value of depends on the reference temperature which is not mentioned
in the text-book. )

Ignoring variations in dimensions of the conductor, the above equation can also be written
.e

for the resistance of the conductor as follows:

R = R [1 + ( - )]
0 0
w

The graph 1 shows resistivity vs. temperature for good conductors. At lower temperatures
( < 50 K ), the graph is non-linear and becomes linear near the room temperature. At higher
temperatures, it again becomes non-linear.
w
w

Graph 1 Graph 2 Graph 3

 3 - CURRENT ELECTRICITY Page 6

Nichrome ( an alloy of nickel and chromium ) has very high resistivity with low temperature
dependence as shown in graph 2. Manganine ( an alloy of copper, manganese and nickel ) has
resistivity which is almost constant with respect to the temperature. The resistivity of
nichrome does not become zero even at absolute zero temperature, while the resistivity of
pure metal becomes almost zero at absolute zero temperature which helps testing its purity.

Carbon, germanium, silicon and various other materials have negative value of meaning

om
that their resistivity decreases with temperature as shown in graph 3. Such materials are
known as semi-conductors.

The relaxation time and to some extent the charged carrier density n, change with
temperature in a semi-conductor and an insulator. The variation of n with temperature T is
given by the equation

.c
Eg
k T

ce
B
nT = n0 e ,

where Eg is the energy gap between the upper portion of the valence band and lower portion
of the conduction band. kB is the Boltzmanns constant. The equation suggests that for a

resistivity.

3.6 Limitations of Ohms Law

ra
semi-conductor, n increases with temperature thus increasing conductivity and reducing its
m
Many components in the electric circuit have the following V - characteristics.
xa

1. They are non-linear.

2. The absolute value of V depends on the polarity of V ( i.e., it depends on its direction ).

3. V can have more than one value for a given value of current.
.e

These are the limitations of Ohms law.

3.7 Superconductivity
w

The resistance of certain materials becomes almost zero, when its temperature is lowered
below certain fixed temperature ( known as critical temperature Tc ). The material in this
w

situation is known as superconductor and this phenomenon is known as superconductivity.

Kamerlingh Onnes in 1911 showed that when the temperature of a specimen of mercury ( Hg )
w

6
is reduced to 4.3 K, its resistance reduces to 0.084 and at 3 K, it becomes 3 10
which is almost one lakhth part of its resistance at 0 C. Many metals and alloys exhibit the
property of superconductivity. Si, Ge, Se and Te are some of the semi-conductors which
behave as super-conductors under high pressure and low temperatures.

When current flows through a superconductor, its resistance being almost zero, practically no
electrical energy is lost as heat and the current is sustained over a long time interval.

The biggest hurdle in the commercial application of superconductors is the need for low
temperature. Efforts are on by researchers all over the world to invent materials which can
 3 - CURRENT ELECTRICITY Page 7

be used as superconductor at room temperature and thus transmission losses of electrical

power can be minimized.

Scientists Bardeen, Cooper and Schrieffer explained the phenomenon of superconductivity

using quantum mechanics. Their theory is known as BCS theory. This theory is based on
prediction of attraction between electrons under special circumstances. Physicists Bendnorz
and Muller prepared compounds of copper oxides in 1986 having critical temperature of 30 K
for which they were awarded Nobel Prize. Thereafter, critical temperature upto 135 K has been

om
reached. Such super-conductors are known as high critical temperature super-conductors
( HTS ). HTS has applications in thin film devices, electric transmission over long distances,
leviating trains ( which can achieve speeds of 550 km / h ).

3.7 ( a ) Meissner Effect

.c
Meissner and Ochsenfeld discovered in 1933 that if a

ce
conducting material is kept in magnetic field at less
than its critical temperature, the magnetic field lines
are pushed away from it as shown in the figure. This
effect is known as Meissner effect.

ra
It can be said from Meissner effect that the magnetic
field inside the superconductor is zero.
m
3.8 Electric Circuits and Kirchhoffs Rules
xa

Kirchhoffs First Rule:

The algebraic sum of electric currents flowing through any junction is zero.
.e

Refer to the junction point O of the network as shown in the figure. 1, 2, ..., 5, are the
currents meeting at the junction point O. Let Q1, Q2,..., Q5 be the corresponding charges
flowing in time t.
w

Q1 Q2 Q5
Then, 1 = , 2 = , ....., 5 = .
t t t
The total electric charge flowing towards the junction point = Q1 + Q3 and
w

the total electric charge flowing out of the junction point = Q2 + Q4 + Q5 in the same time.

Hence, by the law of conservation of electric charge,

w

Q1 + Q3 = Q2 + Q4 + Q5

1 t + 3 t = 2t + 4t + 5t

1 + ( - 2 ) + 3 + ( - 4 ) + ( - 5 ) = 0
It is clear from the above result that the algebraic sum
of electric currents meeting at a junction is zero.
 3 - CURRENT ELECTRICITY Page 8

Kirchhoffs Second Rule:

The algebraic sum of the products of resistances and the corresponding currents flowing
through them is equal to the algebraic sum of the emfs applied along the loop.

Kirchhoffs second rule is based on the conservation of energy and the concept of the
electric potential.

om
Consider a closed path ABCDA formed using resistors
R1, R2, R3, R4 and batteries having emfs 1 and 2.

The electric potential at any point in a steady circuit does

not change with time. If VA is the electric potential at

.c
point A, then on measuring the electric potential at various
points in the closed path ABCDA and coming back to A,
the electric potential would again be equal to VA. This
singular value of the electric potential is based on the law

ce
of conservation of energy.

Starting from A, as we move in a clockwise direction in the loop, the electric potential
reduces by 1R1. This is because current flows from A to B which means that the end A of

ra
the resistor R1 is at a higher potential. The potential increases by 1 as we move from
negative terminal to positive terminal of battery having emf 1. Potential increases on going
from point B to point C through the resistor R2, as the direction of current is from C to B.
m
Counting electric potential this way, on reaching the point A back, potential will be again VA.

VA - 1R1 + 1 + 2R2 - 3R3 - 2 + 4R4 = VA

( - 1R1 ) + 2R2 + ( - 3R3 ) + 4R4 = 2 - 1
xa

This is the statement of Kirchhoff's second rule derived on the basis of the law of
conservation of energy.
.e

3.9 Series and Parallel Connections of Resistors

Series Connection:
w

When resistors are connected end to end as shown in the figure, the same amount of
current flows through them and they are said to have been connected in series. In this type
of connection, potential difference across each resistor is different and is proportional to the
w

value of the resistor.

Applying Kirchhoffs second rule,

w

R1 + R2 + R3 = V

( R1 + R2 + R3 ) = V

R1 + R2 + R3 = V/ ... ... ... ( 1 )

If these three resistors are replaced by a single resistance R such that the same current
flows through the battery as earlier, then R is called the equivalent resistance of the three
resistors connected in series.
 3 - CURRENT ELECTRICITY Page 9

R = V/ ... ... ... (2)

R = R 1 + R2 + R3 [ from equations ( 1 ) and ( 2 ) ], and in general

R = R1 + R2 + R3 + .......... + Rn

The equivalent resistance of the resistors connected in series is greater than the greatest

om
value of the resistors connected in series combination.

Parallel Connection:

When one of the ends of two or more resistors are connected to a single point and their
other ends are connected to another common point in a circuit as shown in the figure, they

.c
are said to have been connected in parallel. In such a connection, the main line current
distributes in the resistors, but the potential difference across them is the same.

Applying Kirchhoffs second rule to the loops, A - V - B - R1 - A, A

ce
- V - B - R2 - A and A - V - B - R3 - A,
V = 1 R1 = 2 R2 = 3 R3
V V V
1 = , 2 = and 3 =
R1 R2 R3

Applying Kirchhoffs first rule to the junction A,

ra
m
1 1 1 1 1 1
= 1 + 2 + 3 = V + + = + + ... ( 1 )
R
1 R 2 R3 V R
1 R 2 R3
xa

If the parallel combination of resistors is replaced by a single resistor R whose value is such
that the main line current remains the same, then R is called the equivalent resistance of
the three resistors connected in parallel. In that case,
.e

1
V = R = ... ... ( 2 )
V R
1
w

1 1 1
= + + [ from equations ( 1 ) and ( 2 ) ], and in general
R R1 R2 R3
1
1 1 1
w

= + + ..... +
R R1 R2 Rn
w

The equivalent resistance of the resistors connected in parallel is less than the least value of
the resistors connected in parallel combination.

3.10 Measurement of Voltage, Current and Resistance

3.10 ( a ) Ammeter

Ammeter is used for measuring current.

Galvanometer is a current sensing device
which is used for this purpose. However,
there are two practical difficulties in using
galvanometer as an ammeter:
 3 - CURRENT ELECTRICITY Page 10

( 1 ) If we want to measure the current flowing through the resistor R of the circuit shown in
the figure, the current measuring instrument is to be connected in series with it as
shown in the next figure. This adds resistance G of the instrument in the circuit thereby
altering the current in the resistor from the original value to .

( 2 ) Further, a moving coil galvanometer is very sensitive and even a small current through
2
it gives full scale deflection. Also the heat ( Gt ) produced in it due to large current

om
can damage its coil.

To overcome these problems, a low value resistance called shunt is connected in parallel to
the galvanometer. As its value is much smaller than G, most of the current flows through it
and the galvanometer does not get damaged. Moreover, the equivalent resistance of the
modified galvanometer is lower than that of the shunt which when connected in the circuit
does not alter its resistance appreciably and hence the true value of the current is measured.

.c
Formula of Shunt

ce
Let G = maximum current capacity of the galvanometer,

= desired maximum current in the ammeter

S = necessary value of the shunt

ra
The value of the shunt should be so selected that the current G flows through the
galvanometer and the balance - G = s flows through the shunt as shown in the figure.
m
Applying Kirchhoffs second rule to the loop,
xa

G G
- G G + ( - G ) S = 0 S =
G

3.10 ( b ) Voltmeter
.e

Voltmeter is used to measure the potential

difference between any two points of a circuit.
Galvanometer with suitable modification is used
w

for this purpose. However, there are two

practical difficulties in using galvanometer as a
voltmeter:
w

( 1 ) To measure potential difference across a

circuit element, galvanometer has to be
w

connected in parallel to it. This alters the

resistance of the circuit and the current
flowing through the circuit element and hence the potential difference across it.

( 2 ) Further, the galvanometer being a sensitive instrument, a large current can damage its
coil.

To overcome these problems, a high value resistance called series resistance is connected in
series with the galvanometer. If G is the resistance of the modified galvanometer, the new
equivalent resistance of the circuit will be
 3 - CURRENT ELECTRICITY Page 11
' RG
R = R1 + As G > > R, ignoring R, R + G G
R + G
RG
R' = R1 + G R ' = R1 + R
which is the same as the equivalent resistance of the original circuit.

Thus, resistance of the circuit is not changed much and as the value of G is large, most of

om
the current flows through R which helps to measure correct value of IR. Moreover, very small
current flows through the galvanometer due to its large resistance and is thus protected.

Deriving formula for the Series Resistance

Let G = maximum current capacity of the galvanometer,

.c
G = resistance of galvanometer,

V = desired maximum voltage in the voltmeter

ce
Rs = necessary value of the series resistance

Applying Ohms law to the modified galvanometer as shown in the figure,

G ( G + Rs ) = V ra
m
V
Rs = - G
G
xa

3.10 ( c ) Wheatstone Bridge

The network shown in the figure is known as Wheatstone

bridge. It is a closed loop made up of four resistors P, Q,
R and S. A source of emf ( battery ) is connected across
.e

AC and a galvanometer is connected across BD. Three of

the four resistors are known whose values are so adjusted
that the galvanometer shows zero deflection. In this condition,
w

Wheatstone bridge is said to be balanced.

Applying Kirchhoffs second rule to the loop A - B - D - A

under the balanced condition,
w

-P1 + R2 = 0 P1 = R2 ... ... (1)

w

Similarly, applying Kirchhoffs second rule to the loop B - C - D - B,

-Q1 + S2 = 0 Q1 = S2 ... ... (2)

Dividing equation ( 1 ) by equation ( 2 ), we have

P R
= ... ... ( 3 )
Q S
 3 - CURRENT ELECTRICITY Page 12

Hence by using the values of the three known resistors in the above equation, the value of
the fourth unknown resistor can be calculated.

The circuit constructed as shown in the adjoining

figure is used in the laboratory to find the value
of unknown resistance using Wheatstone bridge
principle.

om
Here, a constantan resistive wire of uniform diameter
is used in place of resistors R and S. The wire is
mounted on a wooden plank alongwith a meter rule.
Copper strips are connected at the ends A and B
of the wire as shown in the figure. The terminals
on this strip are connected to a battery. Another

.c
copper strip is fixed between these two strips
forming two gaps. In one gap, an unknown resistor
P is connected and in the other a known resistor Q is connected. One end of a

ce
galvanometer is connected to the mid-point D of this strip and the other end to a jockey
which can slide on the wire AB. For a given value Q, the jockey is slided on the wire in
such a way that galvanometer shows zero deflection. If null point is obtained at C such that
AC = l1 and CB = l2, then from equation ( 3 ) above,

P
Q
=
l

l
1

2
P =
l1
l2
Q ra
m
The value of l1 : l2 is found out for different values of Q from which average value of P is
calculated.
xa

End correction:

Due to copper strips at A and B, additional resistances get introduced in the circuit. Let
and be the additional lengths of the wire representing these resistances. If l1 and 100 - l1
.e

are the lengths of wire on either side of the jockey in the balanced condition on taking the
known resistances P1 and Q1 in the gaps, then
P1 l1 +
w

= ... ... ( 1 )
Q1 100 - l +
1
Now, if l2 and 100 - l2 are the corresponding lengths of wire in the balanced condition on
w

interchanging the resistances P1 and Q1 in the gaps, then

Q1 l2 +
= ... ... ( 2 )
w

P1 100 - l +
2
Q l - Pl P l - Q l
11 12 11 12
Solving equations ( 1 ) and ( 2 ), we get = and = - 100
P - Q P - Q
1 1 1 1

These equations can be used to make the necessary end corrections.

 3 - CURRENT ELECTRICITY Page 13

3.10 ( d ) Potentiometer

The terminal voltage of the battery is given by V = - r.

When we try to measure emf of the battery using a voltmeter, some current does flow
through the battery. Hence, voltmeter measures terminal voltage V and not the emf . If the
term r in the above equation is zero, then only the voltmeter can measure emf of the

om
battery. As internal resistance of the battery is not zero, this means that the current must
be zero. This is not possible in a voltmeter. Hence voltmeter cannot measure emf of the
battery.

To measure emf of the battery, a device known as potentiometer is used.

.c
Principle of potentiometer

Potentiometer is such an arrangement in which one can obtain a continuously varying p.d.,
the principle of which can be utilized to measure emf of a battery with a suitable circuit.

ce
A battery having emf and internal resistance r is
connected in series with a resistance box R and a
long resistive wire of uniform diameter ( so that its
resistance per unit length is constant ).

Let L = length of the resistive wire AB and

ra
= resistance per unit length of the wire.
m
L = resistance of the wire AB.

If R is the resistance of the resistance box, then the current flowing through the wire is
xa

= , where r is the internal resistance of the battery.
R + L + r
.e

Hence, potential difference across wire AC is given by

= l =
w

Vl l, where l is the length of the wire AC.

R + L + r
Vl
is called the potential gradient. Its unit is V/m.
w

The potential difference per unit length =

l
The above equation shows that the potential difference between any two points of the
potentiometric wire is directly proportional to the length of the wire between the two points.
w

Points A and C behave like the positive and negative poles of a battery. By changing the
position of C, one can obtain the continuously varying emf.

Use of Potentiometer: Comparision of emfs of Two Cells

Let 1 and 2 be the emfs of the two batteries. First, the positive pole of the battery having
emf 1 is connected to point A while the negative pole is connected to jockey through a
sensitive galvanometer. When jockey is slided on the wire, galvanometer shows zero
deflection at the position C1 of the jockey. In this balanced condition, potential difference
between the points A and C1 is equal to the emf 1 of the battery.
 3 - CURRENT ELECTRICITY Page 14

1 = l1 ... ... (1)
1 R + L + r

Similarly, if we get null point at C2 with battery

having emf 2 , then we have

om

= l2 ... ... (2)
2 R + L + r

Dividing equation ( 1 ) by equation ( 2 ),

.c
l1
1
=
l2
2

ce
This equation is used to compare emfs of the two batteries. It can also be used to find out
the emf of any battery by comparing it with another standard battery.

One can obtain any desired value of the potential difference between ends of the wire AB of

measure very small emf of the order of mV or even V.

3.11 Combination of Cells

ra
the potentiometer by selecting an appropriate value of R in the resistance box and thereby
m
There are three ways in which cells can be connected:
xa

( 1 ) Series connection, ( 2 ) Parallel connection and ( 3 ) Mixed connection.

Mixed Connection:

Let n = number of cells having emfs 1, 2, ....., n and internal resistances r1, r2, ........rn
.e

connected in series and

m = number of parallel connections of such series of cells.
w

n n
For each series of cells, total emf is and total internal resistance is r .
i=1
i i=1
i
w

n 1 n
For the mixed connection, the total emf is and net internal resistance is r .
i=1
i m i=1 i

w

total emf
Current =
total resistance
=
1
i

R + r
m i
mn
If i = and r i = r, then = ,
mR + nr

where R is the resistance in the circuit.

To determine how to arrange given total number

of cells mn = x in the above mixed connection
of cells for given external resistance R so that the current in the circuit becomes maximum,
we note that
 3 - CURRENT ELECTRICITY Page 15
mn
= which means that for current to be maximum,
( nr - mR )2 + 2 mnrR

nr - mR = 0, or nr = mR or R = nr / m, i.e., when the given number of cells are

so arranged that their equivalent resistance equals the given fixed external resistance.
xr xR
Solving mn = x ... ( 1 ) with nr = mR ... ( 2 ), we get m = and n =

om
R r
and the value of the maximum current is

max =
x
2 rR
( Note: Treatment of maximum current given in example 22 of the text-book and many other
publications is logically defective. Important point to be noted here is that R is not

.c
variable. If R were to be variable, then the maximum current will be when R is zero.
m and n are the variables whose values are to be obtained as above. If the above
equations do not give integer values of m and n, then finding maximum current will

ce
involve examining several alternatives. )

i
Series Connection: For only one series of cells, m = 1, =
R + ri

Parallel Connection:
ra
For m parallel connections each having one cell, n = 1, =
i
r
R + i
m
m
Parallel Connection of Cells with different emfs and different internal resistances:

Two cells having emfs 1 and 2 and internal

xa

resistances r1 and r2 are connected in parallel

as shown in the figure.

Applying Kirchhoffs first rule at junction point A,

.e

= 1 + 2 ... ... (1)

Applying Kirchhoffs second rule to the loop ACDB1A,

w

1 - R 2 - R
R + 1 R1 = 1 1 = and similarly, 2 = ... ... (2)
r1 r2
w

Putting, values of 1 and 2 from equation ( 2 ) in equation ( 1 ),

1 2
w

+
1 - R 2 - R r
1
r
2
= + =
r1 r2 R R
1+ +
r r
1 2
n
i

r
i=1 i
If n cells are connected in parallel in the above arrangement, then =
n 1
1+ R
r
i=1 i