Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 1
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
RC SLAB DESIGN (BS8110:PART1:1997)
TEDDS calculation version 1.0.03
TWO WAY SPANNING SLAB DEFINITION - RESTRAINED
; Overall depth of slab; h = 250 mm
Outer sagging steel
; Cover to outer tension reinforcement resisting sagging; csag = 50 mm
; Trial bar diameter; Dtryx = 25 mm
Depth to outer tension steel (resisting sagging)
dx = h - csag - Dtryx/2 = 188 mm
Inner sagging steel
; Trial bar diameter; Dtryy = 25 mm
Depth to inner tension steel (resisting sagging)
dy = h - csag - Dtryx - Dtryy/2 = 163 mm
Outer hogging steel
; Cover to outer tension reinforcement resisting hogging; chog = 50 mm
; Trial bar diameter; Dtryxhog = 16 mm
Depth to outer tension steel (resisting hogging)
dxhog = h - chog - Dtryxhog/2 = 192 mm
Inner hogging steel
; Trial bar diameter; Dtryyhog = 16 mm
Depth to inner tension steel (resisting hogging)
dyhog = h - chog - Dtryxhog - Dtryyhog/2 = 176 mm
Materials
; Characteristic strength of reinforcement; fy = 500 N/mm2
; Characteristic strength of concrete; fcu = 40 N/mm2
Asyhog Nominal 1 m w idth Asxhog
h dx
h dxhog
Asy Nominal 1 m w idth Asx
Shorter Span
Asyhog Asxhog
h dy
h dyhog
Asy (sagging moments) Asx (hogging moments)
Longer Span
Two-way spanning slab
(restrained)
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 2
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
RESTRAINED 2 WAY SPANNING (CL 3.5.3)
MAXIMUM DESIGN MOMENTS
; Length of shorter side of slab; lx = 5.500 m
; Length of longer side of slab; ly = 7.500 m
; Design ultimate load per unit area; ns = 16.0 kN/m2
; Edge condition shorter side (1); Edge1 = "C"
; Edge condition other shorter side (2); Edge2 = "C"
; Edge condition longer side (3); Edge3 = "C"
; Edge condition other longer side (4); Edge4 = "C"
Number of discontinuous edges
Nd = 0
Moment coefficients
sy = (24 + 2Nd + 1.5Nd2) / 1000 =0.024
1 = if(Edge1 == "C", 4/3sy,0) = 0.032
2 = if(Edge2 == "C", 4/3sy,0) = 0.032
= 2/9 [3 - (18) lx/ly ((sy + 1) + (sy + 2))] = 0.339
3x = if(Edge3 == "C", 4/3,0) = 1.333
4x = if(Edge4 == "C", 4/3,0) = 1.333
sx = / [(1+3x)0.5 + (1+4x)0.5]2 = 0.036
3 = 3x sx = 0.048
4 = 4x sx = 0.048
Maximum span moments per unit width - restrained slabs
msx = sx ns lx2 = 17.6 kNm/m
msy = sy ns lx2 =11.6 kNm/m
Maximum support moments per unit width - restrained slabs
msxhog = max( 3 , 4 ) ns lx2 = 23.5 kNm/m
msyhog = max( 1 , 2 ) ns lx2 =15.5 kNm/m
CONCRETE SLAB DESIGN SAGGING OUTER LAYER OF STEEL (CL 3.5.4)
; Design sagging moment (per m width of slab); msx = 17.6 kNm/m
; Moment Redistribution Factor; bx = 1.0
Area of reinforcement required
;; Kx = abs(msx) / ( dx2 fcu ) = 0.013
K'x = min (0.156 , (0.402 (bx - 0.4)) - (0.18 (bx - 0.4)2 )) = 0.156
Outer compression steel not required to resist sagging
Slab requiring outer tension steel only - bars (sagging)
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 3
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
;; zx = min (( 0.95 dx),(dx(0.5+0.25-Kx/0.9)))) = 178 mm
Neutral axis depth; xx = (dx - zx) / 0.45 = 21 mm
Area of tension steel required
;;; Asx_req = abs(msx) / (1/ms fy zx) = 227 mm2/m
Tension steel
;;Provide 16 dia bars @ 200 centres; outer tension steel resisting sagging
Asx_prov = Asx = 1010 mm2/m
Area of outer tension steel provided sufficient to resist sagging
Concrete Slab Design - Sagging - Inner layer of steel (cl. 3.5.4)
; Design sagging moment (per m width of slab); msy = 11.6 kNm/m
; Moment Redistribution Factor; by = 1.0
Area of reinforcement required
;; Ky = abs(msy) / ( dy2 fcu ) = 0.011
K'y = min (0.156 , (0.402 (by - 0.4)) - (0.18 (by - 0.4)2 )) = 0.156
Inner compression
steel not required to
resist sagging
Slab requiring inner tension steel only - bars (sagging)
;; zy = min (( 0.95 dy),(dy(0.5+0.25-Ky/0.9)))) = 154 mm
Neutral axis depth; xy = (dy - zy) / 0.45 = 18 mm
Area of tension steel required
;;; Asy_req = abs(msy) / (1/ms fy zy) = 173 mm2/m
Tension steel
;;Provide 16 dia bars @ 200 centres; inner tension steel resisting sagging
Asy_prov = Asy = 1010 mm2/m
Area of inner tension steel provided sufficient to resist sagging
CONCRETE SLAB DESIGN HOGGING OUTER LAYER OF STEEL (CL 3.5.4)
; Design hogging moment (per m width of slab); msxhog = 23.5 kNm/m
; Moment Redistribution Factor; bx = 1.0
Area of reinforcement required
;; Kxhog = abs(msxhog) / ( dxhog2 fcu ) = 0.016
K'x = min (0.156 , (0.402 (bx - 0.4)) - (0.18 (bx - 0.4)2 )) = 0.156
Outer compression steel not required to resist hogging
Slab requiring outer tension steel only - bars (hogging)
;; zxhog = min (( 0.95 dxhog),(dxhog(0.5+0.25-Kxhog/0.9)))) = 182 mm
Neutral axis depth; xxhog = (dxhog - zxhog) / 0.45 = 21 mm
Area of tension steel required
;;; Asxhog_req = abs(msxhog) / (1/ms fy zxhog) = 296 mm2/m
Tension steel
;;Provide 16 dia bars @ 200 centres; outer tension steel resisting hogging
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 4
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
Asxhog_prov = Asxhog = 1010 mm2/m
Area of outer tension steel provided sufficient to resist hogging
Concrete Slab Design - hogging - Inner layer of steel (cl. 3.5.4)
; Design hogging moment (per m width of slab); msyhog = 15.5 kNm/m
; Moment Redistribution Factor; by = 1.0
Area of reinforcement required
;; Kyhog = abs(msyhog) / ( dyhog2 fcu ) = 0.013
K'y = min (0.156 , (0.402 (by - 0.4)) - (0.18 (by - 0.4)2 )) = 0.156
Inner compression
steel not required to
resist hogging
Slab requiring inner tension steel only - bars (hogging)
;; zyhog = min (( 0.95 dyhog),(dyhog(0.5+0.25-Kyhog/0.9)))) = 167 mm
Neutral axis depth; xyhog = (dyhog - zyhog) / 0.45 = 20 mm
Area of tension steel required
;;; Asyhog_req = abs(msyhog) / (1/ms fy zyhog) = 213 mm2/m
Tension steel
;;Provide 16 dia bars @ 200 centres; inner tension steel resisting hogging
Asyhog_prov = Asyhog = 1010 mm2/m
Area of inner tension steel provided sufficient to resist hogging
Check min and max areas of steel resisting sagging
;Total area of concrete; Ac = h = 250000 mm2/m
; Minimum % reinforcement; k = 0.13 %
Ast_min = k Ac = 325 mm2/m
Ast_max = 4 % Ac = 10000 mm2/m
Steel defined:
; Outer steel resisting sagging; Asx_prov = 1010 mm2/m
Area of outer steel provided (sagging) OK
; Inner steel resisting sagging; Asy_prov = 1010 mm /m 2
Area of inner steel provided (sagging) OK
Check min and max areas of steel resisting hogging
;Total area of concrete; Ac = h = 250000 mm2/m
; Minimum % reinforcement; k = 0.13 %
Ast_min = k Ac = 325 mm2/m
Ast_max = 4 % Ac = 10000 mm2/m
Steel defined:
; Outer steel resisting hogging; Asxhog_prov = 1010 mm2/m
Area of outer steel provided (hogging) OK
; Inner steel resisting hogging ; Asyhog_prov = 1010 mm2/m
Area of inner steel provided (hogging) OK
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 5
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
SHEAR RESISTANCE OF CONCRETE SLABS (CL 3.5.5)
Outer tension steel resisting sagging moments
; Depth to tension steel from compression face; dx = 188 mm
; Area of tension reinforcement provided (per m width of slab); Asx_prov = 1010 mm2/m
; Design ultimate shear force (per m width of slab); Vx = 60 kN/m
; Characteristic strength of concrete; fcu = 40 N/mm2
Applied shear stress
vx = Vx / dx = 0.32 N/mm2
Check shear stress to clause 3.5.5.2
vallowable = min ((0.8 N1/2/mm) (fcu ), 5 N/mm2 ) = 5.00 N/mm2
Shear stress - OK
Shear stresses to clause 3.5.5.3
Design shear stress
fcu_ratio = if (fcu > 40 N/mm2 , 40/25 , fcu/(25 N/mm2)) = 1.600
vcx = 0.79 N/mm2 min(3,100 Asx_prov / dx)1/3 max(0.67,(400 mm / dx)1/4) / 1.25 fcu_ratio1/3
vcx = 0.73 N/mm2
Applied shear stress
vx = 0.32 N/mm2
No shear reinforcement required
SHEAR RESISTANCE OF CONCRETE SLABS (CL 3.5.5)
Inner tension steel resisting sagging moments
; Depth to tension steel from compression face; dy = 163 mm
; Area of tension reinforcement provided (per m width of slab); Asy_prov = 1010 mm2/m
; Design ultimate shear force (per m width of slab); Vy = 60 kN/m
; Characteristic strength of concrete; fcu = 40 N/mm2
Applied shear stress
vy = Vy / dy = 0.37 N/mm2
Check shear stress to clause 3.5.5.2
vallowable = min ((0.8 N1/2/mm) (fcu ), 5 N/mm2 ) = 5.00 N/mm2
Shear stress - OK
Shear stresses to clause 3.5.5.3
Design shear stress
fcu_ratio = if (fcu > 40 N/mm2 , 40/25 , fcu/(25 N/mm2)) = 1.600
vcy = 0.79 N/mm2 min(3,100 Asy_prov / dy)1/3 max(0.67,(400 mm) / dy)1/4 / 1.25 fcu_ratio1/3
vcy = 0.79 N/mm2
Applied shear stress
vy = 0.37 N/mm2
No shear reinforcement required
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 6
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
SHEAR PERIMETERS FOR A RECTANGULAR CONCENTRATED LOAD (CL 3.7.7)
; Length of loaded rectangle; l = 400 mm
; Width of loaded rectangle; w = 200 mm
; Depth to tension steel; dx = 188 mm
; Dimension from edge of load to shear perimeter; lp = kp dx = 281 mm; where; kp = 1.50
For punching shear cases not affected by free edges or holes:
Total length of inner perimeter at edge of loaded area; u0_gen = 2 (l + w) = 1200 mm
Total length of outer perimeter at l p from loaded area; ugen = 2 (l + w) + 8 lp 3450 mm
PUNCHING SHEAR AT CONCENTRATED LOADS (CL 3.7.7)
Tension steel resisting sagging
; Total length of inner perimeter at edge of loaded area; u0 = 1200 mm
; Total length of outer perimeter at dimension l p from loaded area; u = 3450 mm
; Depth to outer steel; dx = 188 mm
; Depth to inner steel; dy = 163 mm
Average depth to "tension" steel; dav = (dx + dy)/2 = 175.0 mm
; Area of outer steel per m effective through the perimeter; Asx_prov = 1010 mm2 /m
; Area of inner steel per m effective through the perimeter; Asy_prov = 1010 mm2 /m
; Max shear effective across either perimeter under consideration; Vp = 60 kN
; Characteristic strength of concrete; fcu = 40 N/mm2
Applied shear stress
Stress around loaded area; vmax = Vp / (u0 dav) = 0.286 N/mm2
Stress around perimeter; v = Vp / (u dav) = 0.099 N/mm2
Check shear stress to clause 3.7.7.2
vallowable = min ((0.8 N1/2/mm) (fcu ), 5 N/mm2 ) = 5.000 N/mm2
Shear stress - OK
Shear stresses to clause 3.7.7.4
Design shear stress
fcu_ratio = if (fcu > 40 N/mm2 , 40/25 , fcu/(25 N/mm2)) = 1.600
; Effective steel area for shear strength determination:; As_eff =1010 mm2/m;
vc = 0.79 N/mm2 min( 3, 100( As_eff / dav ) )1/3 max(0.67, (400 mm / dav )1/4) / 1.25 fcu_ratio1/3
vc = 0.757 N/mm2
No shear reinforcement required
CONCRETE SLAB DEFLECTION CHECK (CL 3.5.7)
; Slab span length; lx = 5.500 m
; Design ultimate moment in shorter span per m width; msx = 18 kNm/m
; Depth to outer tension steel; dx = 188 mm
Tension steel
; Area of outer tension reinforcement provided; Asx_prov = 1010 mm2/m
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 7
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
; Area of tension reinforcement required; Asx_req = 227 mm2/m
; Moment Redistribution Factor; bx = 1.00
Modification Factors
;Basic span / effective depth ratio (Table 3.9); ratiospan_depth = 20
The modification factor for spans in excess of 10m (ref. cl 3.4.6.4) has not been included.
;fs = 2 fy Asx_req / (3 Asx_prov bx ) = 75.0 N/mm2
factortens = min ( 2 , 0.55 + ( 477 N/mm 2 - fs ) / ( 120 ( 0.9 N/mm2 + msx / dx2))) = 2.000
Calculate Maximum Span
This is a simplified approach and further attention should be given where special circumstances exist. Refer to clauses
3.4.6.4 and 3.4.6.7.
Maximum span; lmax = ratiospan_depth factortens dx = 7.50 m
Check the actual beam span
Actual span/depth ratio; lx / dx = 29.33
Span depth limit; ratiospan_depth factortens = 40.00
Span/Depth ratio check satisfied
CHECK OF NOMINAL COVER (SAGGING) (BS8110:PT 1, TABLE 3.4)
; Slab thickness; h = 250 mm
; Effective depth to bottom outer tension reinforcement; dx = 187.5 mm
; Diameter of tension reinforcement; Dx = 16 mm
; Diameter of links; Ldiax = 10 mm
Cover to outer tension reinforcement
ctenx = h - dx - Dx / 2 = 54.5 mm
Nominal cover to links steel
cnomx = ctenx - Ldiax = 44.5 mm
Permissable minimum nominal cover to all reinforcement (Table 3.4)
; cmin = 25 mm
Cover over steel resisting sagging OK
CHECK OF NOMINAL COVER (HOGGING) (BS8110:PT 1, TABLE 3.4)
; Slab thickness; h = 250 mm
; Effective depth to bottom outer tension reinforcement; dxhog = 192.0 mm
; Diameter of tension reinforcement; Dxhog = 16 mm
; Diameter of links; Ldiaxhog = 10 mm
Cover to outer tension reinforcement
ctenxhog = h - dxhog - Dxhog / 2 = 50.0 mm
Nominal cover to links steel
cnomxhog = ctenxhog - Ldiaxhog = 40.0 mm
Permissable minimum nominal cover to all reinforcement (Table 3.4)
Project Job Ref.
54 Russell Road, London 1382
Engineering Force LTD
Section Sheet no./rev.
Suspended Basement Slab design -1 8
Calc. by Date Chk'd by Date App'd by Date
EF 20/08/2014 EF
; cmin = 25 mm
Cover OK over steel resisting hogging
;
