Scribd
Upload
409 views

EC Lab Manual

This document summarizes two experiments in basic electronics: 1) Studying series and parallel resistive circuits to verify Ohm's law and voltage/current divider rules. Different resistor values were used to measure voltages and currents. 2) Measuring Lissajous patterns between two signals to calculate the capacitor value required for a 600 phase shift when connected in series with a 10k resistor. The circuit was set up and the CRO was used to observe inputs/outputs in XY mode to calculate the phase angle.

Uploaded by

sruthy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
409 views

EC Lab Manual

This document summarizes two experiments in basic electronics: 1) Studying series and parallel resistive circuits to verify Ohm's law and voltage/current divider rules. Different resistor values were used to measure voltages and currents. 2) Measuring Lissajous patterns between two signals to calculate the capacitor value required for a 600 phase shift when connected in series with a 10k resistor. The circuit was set up and the CRO was used to observe inputs/outputs in XY mode to calculate the phase angle.

Uploaded by

sruthy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

BASIC ELECTRONICS LAB

1. STUDY OF SERIES AND PARALLEL RESISTIVE CIRCUITS

AIM:

To verify:

(i) Ohms law in series and parallel resistive network.


(ii) Voltage divider rule in series circuits.
(iii)Current divider rule in parallel circuits.

CIRCUIT DIAGRAM:

Ohms law: V = I * R

Use different values of Resistor and measure current

CALCULATED VALUE MEASURED VALUE


VOLTAGE R I=V/R VOLTAGE I RESISTANCE
i/p (color code) in mA i/p (V) (meter) (V/I)

5v

3
DIVISION OF ELECTRONICS,SOE
BASIC ELECTRONICS LAB

(i) SERIES CONNNECTION:

Use different values of Resistor R1&R2 and measure voltages V1 &V2

CALCULATED MEASURED
INPUT VOLTAGE
R1 R2 (color code) (from meters)
(V)
V1 V2 V1 V2

CALCULATION:

=
+

=
+

4
DIVISION OF ELECTRONICS,SOE
BASIC ELECTRONICS LAB

(ii) PARALLEL CONNECTION:

Use different values of Resistor R1&R2 and measure currents I1 , I2 & I

Voltage Calculated Calculated Measured Total


(v) Current (I) R1 R2 I1 I2 I1 I2 I=I1+I2
I= I1 + I2

CALCULATION:

=
+

=
+

RESULTS:

5
DIVISION OF ELECTRONICS,SOE
BASIC ELECTRONICS LAB

2. PHASE MEASUREMENT (LISSAJOUS PATTERN)

AIM:

(i) To study Lissajous pattern of two signals.


(ii) Calculate the value of capacitor required to produce a 600 phase shift
when connected in series with 10k resistor.
CIRCUIT DIAGRAM:

PROCEDURE:

Set up the circuit as shown in figure. Select an input sine waveform from function
generator and observe the input on channel X and output on channel Y. Keep the
CRO in XY mode. Calculate the phase angle using the expression Sin-1(Y1/Y2).

DESIGN:

Let R=10K =600

tan = XC /R

XC = R* tan

XC = 1/c = 1/2fc

C=

6
DIVISION OF ELECTRONICS,SOE
BASIC ELECTRONICS LAB

OBSERVATION:

= SIN-1(Y1/Y2)

RESULT:

Measured value:

Calculated value:

7
DIVISION OF ELECTRONICS,SOE

You might also like