100% found this document useful (2 votes)
4K views2 pages

Design and Drawing of Irrigation Structures

This document provides instructions for two design problems involving irrigation structures. The first problem asks students to design a sluice taking off from an irrigation tank, providing dimensions and details of the tank bund, sluice sill, and outlet channel. Students are asked to draw longitudinal sections, plans, and cross sections of the sluice tower and barrel. The second problem provides specifications for designing a regulator cum road bridge, including discharge rates, dimensions of the channel and banks, and roadway requirements. Students are asked to draw longitudinal sections, plans, a section through the regulator vent, and a cross section of wing walls.

Uploaded by

sainath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (2 votes)
4K views2 pages

Design and Drawing of Irrigation Structures

This document provides instructions for two design problems involving irrigation structures. The first problem asks students to design a sluice taking off from an irrigation tank, providing dimensions and details of the tank bund, sluice sill, and outlet channel. Students are asked to draw longitudinal sections, plans, and cross sections of the sluice tower and barrel. The second problem provides specifications for designing a regulator cum road bridge, including discharge rates, dimensions of the channel and banks, and roadway requirements. Students are asked to draw longitudinal sections, plans, a section through the regulator vent, and a cross section of wing walls.

Uploaded by

sainath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

H.T.No.

Code No: CE1543 GEC-R14


IV B. Tech I Semester Regular Examinations, November 2017
DESIGN AND DRAWING OF IRRIGATION STRUCTURES
(Civil Engineering)
Time: 3 Hours Max. Marks: 60

1 60 = 60M
1. Design a sluice taking off from a tank irrigating 160 hectares at an average duty of 700
hectares/cumecs
The earthen dam of an irrigation tank has the following data:
Top width of bund =2m
Side slopes of bund = 2:1 on both sides
R.L of top of bund = 128.50 m
Full tank level = 125.50 m
Max water level = 126.50 m
Average lower water level = 123.00 m
Sill of the sluice at off take = 122.50 m
Good foundation = 121.50 m
The details of the channel below the sluice are as under
Bed level : 122.00 m
FSL : 122.50 m
TBL : 123.50 m
Side slope :1:1
Draw i) Longitudinal section along the c.l of the barrel.
ii) Half plan at top and half at foundation.
iii) Cross section of the tower head and of the rectangular barrel.
(OR)
2. Design a regulator cum road bridge with the following particulars:
Particulars Upstream Downstream
3
Full supply discharge (FSQ)(m /s) 18.0 15.0
Bed width (m) 12 12
Bed level (m) +50.00 +50.00
Full Supply Level (FSL) (m) +52.00 +51.75
Top level of Bank (m) +53.00 +52.75
Top width of Bank (m) 2.0 2.0
Side slopes (H:V) 2:1 2:1

Page 1 of 2
The regulator carries a roadway single lane designed for IRC loading class 'A'. Provide
freeboard of one meter above F.S.L for the road bridge.
Assume Hydraulic gradient 1 in 10
General ground level at this site +52.00m
Good soil for foundation is available at +49.00m
Splayed type wing-walls are to be provided.
Draw to suitable scale the following views:
i) Half longitudinal section and half longitudinal elevation.
ii) Half plan at top and half at foundation level.
iii) Sectional elevation through regulator vent.
iv) Cross section of wing walls.

*****

Page 2 of 2

You might also like