Owner of the content within this article is www.isaserver.
org
Written by Marc Grote – www.it-training-grote.de
ISA Server 2006 – Site to Site VPN with Cisco PIX 501
Abstract
In this article I will give you a Step by Step Solution to implement a Site to Site VPN
with Cisco PIX and ISA Server 2006.
Let's begin
ISA Server 2006 is the next step in Microsoft’s Security Strategy. ISA Server 2006 is
the successor of ISA Server 2004. ISA Server 2006 RTM is expected to release at
end of June 2006 so this article is based on a Beta version of ISA Server 2006.
For your better understand i created a Topology diagram about the ISA Server 2006
and Cisco Pix config.
Figure 1: Network diagram
We are starting the Site to Site VPN configuration at ISA Server 2006 site. Start the
ISA Server Management console and navigate to Virtual Private Networks (VPN) to
create a new VPN Site to Site Network.
Figure 2: Network diagram
Name the new Site to Site VPN network PIXNET.
Figure 3: Name the Site to Site VPN connection
Cisco Pix only supports IP Security (IPSEC Tunnel Mode), so we select this option.
For every other Site to Site VPN you shouldn’t select IPSEC Tunnel Mode VPN.
Figure 4: Select IPSEC Tunnel Mode
Specifiy the IP address of the Outside interface from Cisco Pix and the Local
Interface IP address from ISA Server 2006.
Figure 5: Specify Remote and Local VPN Gateway IP Addresses
For a Site to Site VPN Gateway connection you must use a certificate from a CA or a
Pre Shared Key. For this example we will use the very simple Pre Shared Key
12345678. If you don’t use certificates, what is recommended, you should specify a
long and complex Pre Shared Key.
Figure 6: Insert the Pre Shared Key
Now specify the Remote Site network behind the Cisco Pix which you want to access
from ISA Server site.
Figure 7: Specify the Remote Site IP Addresses
Read the summary of the Wizard and finish the VPN configuration on ISA site.
Figure 8: VPN Site to Site summary
View the IPSEC Policy configured by the ISA Site to Site VPN wizard.
Figure 9:IPSEC policy summary
Note the IPSEC Policy settings because they must match the Settings that you will
configure on Cisco PIX site.
Figure 10: IPSEC details
After creating the Site to Site VPPN you must create a Network rule between Cisco
Pix and ISA.
Figure 11: Network rule between ISA and PIX
The Source Network is Internal.
Figure 12: Specify the internal Network
The Network destination is the Cisco Pix Network PIXNET.
Figure 13: Specify the Destination Network
The Network Relationship is Route.
Figure 14: The Network Relationship is Route
After creating the Network Rule you must create two Firewall rules rules to allow
access between Cisco PIX Net and ISA Net. If the two networks are trusted create a
Firewall rule which allows full access else create a Firewall rule with limited access.
Figure 15: Create two Firewall rules
Now it is time to configure the Cisco Pix site. Start the Cisco PDM.
Figure 16: Cisco Pix PDM
Start the Cisco Pix VPN Wizard and select Site to Site VPN. The Interface is the
Outside Interface.
Figure 17: VPN Wizard
Specify the Peer IP Address. This is the IP Address of the external ISA Server 2006
interface.
Enter the Pre Shared Key that you had configured at ISA Server Site (12345678).
Figure 18: Specify remote IP address and Pre Shared Key
Enter the IKE Policy settings shown in the following picture to match the ISA VPN
config.
Figure 19: Enter IKE Policy settings
Next, specify the Transform Set settings shown in the following picture.
Figure 20: Transform Set settings
In the next VPN Wizard dialog page enter the IP Address Range from the Network
behind the Pix (from the Inside Interface).
Figure 21: IPSEC Traffic selector
Enter the IP address range from the Internal network protected by ISA Server 2006.
Figure 22: Remote Network IP Address Range
If it is the First time that PDM creates the Network, PDM asks to add the Remote
Host or Network to the Cisco Pix configuration set. Click OK.
Figure 23: PDM creates Network Objects
Enter the configuration information for the remote Site network. Select the Outside
Interface of the Pix.
Figure 24: Remote Site Network
Cisco Pix must know the route to the Remote Site Network so create a static route to
the Destination Network.
Figure 25: Create a static rule
Click Finish to close the Network Create Wizard at Cisco Pix Site.
Figure 26: Finish the Network create Wizard
Click Finish.
Figure 27: Click Finish
Click Save to store the VPN configuration in Cisco Pix NVRAM.
Figure 28: Save configuration in NVRAM
After creating the VPN Site to Site configuration at Cisco Pix site, you must change
some IPSEC settings. To do so, click Access Rules and then IPSEC – Tunnel Policy.
Figure 29: Change IPSEC Policy settings
In the following picture you can see the Cisco Pix config settings for the Tunnel
Policy before modifying.
Figure 30: IPSEC Tunnel Policy before modifying
You must change the Security Association Lifetime to 100000 Kilobytes, the Lifetime
to 01 Hour and enable PFS (Perfect Forward Secrecy).
Figure 31: Change IPSEC Tunnel Policy
After changing IPSEC Policy settings click IKE – Policies and then Edit.
Figure 32: Change IKE settings
IKE Policy before changes.
Figure 33: IKE Policy before changing
Change the IKE Lifetime from 86400 seconds to 28800 seconds.
Figure 34: IKE Policy after configuration change
The last step is to configure the same IKE and ISPEC Policy settings made in the
Cisco PIX config also on ISA Server site. Start the ISA Management Console and
click into the Properties of the Site to Site VPN connection to the Cisco Pix and click
Connection – IPSEC Settings – Phase II and change the Key generation to every
100000 Kbytes.
Figure 35: Change IPSEC Phase II settings on ISA Site
Now you should successfully Ping a Host on every Site of the Remote Site protected
by Cisco Pix or ISA Server 2006.
Figure 36: Try to Ping a Host on the Remote Site Network
Conclusion
I hope this article was useful for you to see how to implement a Site to Site VPN with
Cisco PIX 501 and ISA Server 2006.
Related Links
ISA Server 2006 Overview
http://www.microsoft.com/isaserver/2006/default.mspx
Download the ISA Server 2006 Trial
http://www.microsoft.com/isaserver/2006/beta.mspx
ISA Server 2006 Reviewers Guide
http://www.microsoft.com/isaserver/2006/prodinfo/guide.mspx
