SLAB DESIGN :- Out House Room

(One long & one short edge discontineous)

(TWO WAY)
Short Span (Clear) 2.50 m
Long Span (Clear) 2.00 m
Live Load on the Slab (LL) 3.50 KN / sqm
Comp.stess of concrete M - 15 (fck) 15.00 N / sqm
Tensile stress of steel (fy) 415.00 N / sqm
Unit wt of concrete 25.00 KN / cum
Unit wt of floor finish 50 mm 24.00 KN / sqm
Clear concrete cover 15.00 mm
Bearing of slab 230.00 mm
Overall depth 83.33 mm
Provide Overall depth D 125.00 mm
Dia of bars for short direction 10.00 mm
Dia of bars for long direction 10.00 mm
Effective Depth d 105.00 mm
Loading on the slab
Dead Load of the slab (DL) 3.13 KN / sqm
Floor Finish 1.00 KN / sqm
Other Load 0.50 KN / sqm
Live Load on the slab 3.5 KN / sqm
Total Load on the slab (TL) 8.13 KN / sqm
Design Load = (Total Load x Load Factor i.e. 1.5) 12.19 KN / sqm
Effective Span lx 2.61 m
ly 2.11 m
Ratio ly/lx 0.808
From Table (26 or 27 of IS 456) BM Coefficients are as follows;
1.5 ax 1.75 ay
For negative moments (at top) 0.075 0.050090211 0.084 0.047
For positive moments (at bottom) 0.056 0.03662572 0.063 0.035
Calculated BM per unit width of slab are as follows;
Mx = ax w lx2 My = ay w lx2
For negative moments (at top) 4.14 3.89 KN-m/m
For positive moments (at bottom) 3.03 2.89 KN-m/m

Effective depth of slab will now be fixed up on consideration of

of flexural strength as well as control of deflection.
Flexural strength consideration
Maximum BM = 4.14 KN-m/m
BM = 0.36 x fck x 0.48 (1-0.42 x 0.48) x 1000 d =
2
BM x 106 N-mm/m
or 0.36 x 15 x 0.48 (1-0.42 x 0.48) x 1000 d =2
4142694.867
or d= 45 mm
Tension R/F for the positive BM along the short span is
BM = 3.03
Ast = BM / 0.87 x fy (1-0.42 x 0.48) x d
= 3029118 / 0.87 x 415 (1-0.42 x 0.48) x 45
= 234.9 mm2/m
Control of deflection
Actual Span / effective depth ratio = 2605 / 45
= 58.22
pt = 100 Ast/bd = 100 x 234.9 / 1000 x 45 = 0.52
From Modification curve, Modification factor = 1.2
 Basic value of span / effective depth ratio = 26
Therefore permitted value of span / effective depth ratio = 26 x 1.2
= 31.2
Actual S/d is > Permitted S/d
Hence effective depth "d" should be increase
Try an effective depth "d" = 100 mm
Tension R/F for short span +BM is given by =
0.87 x fy x Ast (d - fy x Ast / (fck x 1000)) = 3.03 x 1000000
0.87 x 415 x Ast (100 - 415 x Ast / (15 x 1000)) = 3029118.422
8666271 OK 3029118.4
Ast = 258.52 Very this steel area
Actual Span / effective depth ratio = 2605 / 100 to make "OK"
= 26.05
pt = 100 Ast/bd = 100 x 258.52 / 1000 x 100 = 0.259
From Modification curve, Modification factor = 1.45
Basic value of span / effective depth ratio = 26 Change as per curv
Therefore permitted value of span / effective depth ratio = 26 x 1.45 for "pt"
= 37.70
Actual S/d is < Permitted S/d
Hence effective depth "d" should be OK
Adopt Overall thickness (D) = 120 mm
Minimum R/F in slab = 0.12% of area of slab
= 0.12 x D x 1000 / 100
= 144 mm2/m 8 mm dia 349 mm c/c
0.87 x 415 x Ast (d - 415 x Ast / (15 x 1000)) = BM x 1000000
Effective depth for R/F in long direction will, therefore, be = 100 - dia. Of long R/F
= 100 - 10 = 90.00 mm
Tension R/F per unit width of slab calculated by above eq. For different BM are as follow;
Bendind Moments
Short Span Long Span
For negative moments (at top) 4.14 KN-m/m 3.89 KN-m/m
For positive moments (at bottom) 3.03 KN-m/m 2.89 KN-m/m
Reinforcements
Short Span Long Span
Top R/F (At support) 357.00 Very these R/F area 233.00 mm2/m
Bottom R/F (At Mid Span) 258.52 for the BM 160.00 mm2/m
These R/F will be provided within the middle strips in the two directions.
Adopting 8 or 10 mm dia bars for the R/F, the calculated spacing of bars will be as follows;
Reinforcements Spacing
Dia of bars Short Span Dia of bars Long Span
Top R/F (At support) 10.00 210 10.00 330 mm c/c
Bottom R/F (At Mid S 10.00 300 10.00 490 mm c/c
Maximum Spacing 300 270 mm c/c
No. of bars in slab
Short Span Long Span
Top R/F 11.00 Nos. of Length 2105 mm 8.00 Nos. of Length 2605 mm
Bottom R/F 8.00 Nos. of Length 2105 mm 6.00 Nos. of Length 2605 mm
Very this steel area
to make "OK"

Change as per curve

for "pt"
 SLAB DESIGN :- Out House Room
Edges conditions :- (One long & one short edge discontineous)

Room Size :- x Ft. Thickness of Slab :- 120 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 4.14 3.89 KN-m/m
For positive moments (at bottom) Mid Span:- 3.03 2.89 KN-m/m
Maximum R/F(Flexural Consideration) :- 234.86 mm2/m, 8 mm dia. 214 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 357.00 mm2/m 10 mm dia. 210 mm c/c
Bottom At Mid Span : 258.52 mm2/m 10 mm dia. 300 mm c/c
Long Span
Top At support :- 233.00 mm2/m 10 mm dia. 270 mm c/c
Bottom At Mid Span : 160.00 mm2/m 10 mm dia. 270 mm c/c

Minimum R/F :- 144.00 mm2/m 8 mm dia 349 mm c/c

Maximum Spacing :- 270 mm

382539833.xlsx[Report] 5/12 03/25/2018(14:05:54)

 SLAB DESIGN :- Frontside Bed Room
Edges conditions :- (All four edges contineous)

Room Size :- 12.5 x 13.25 Ft. Thickness of Slab :- 125 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1.2 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 6.69 6.13 KN-m/m
For positive moments (at bottom) Mid Span:- 5.04 4.60 KN-m/m
Maximum R/F(Flexural Consideration) :- 307.77 mm2/m, 8 mm dia. 162 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 183.52 mm2/m 8 mm dia. 270 mm c/c
Bottom At Mid Span : 136.65 mm2/m 8 mm dia. 300 mm c/c
Long Span
UP Top At support :- 182.61 mm2/m 8 mm dia. 270 mm c/c
Bottom At Mid Span : 135.04 mm2/m 8 mm dia. 294 mm c/c

Minimum R/F :- 150.00 mm2/m 8 mm dia 335 mm c/c

Maximum Spacing :- 294 mm

8 mm dia.
7" c/c

8 mm dia.
9" c/c

8 mm dia.
6" c/c

UP

382539833.xlsx[1] 6/12 03/25/2018[14:05:54]

 UP

382539833.xlsx[1] 7/12 03/25/2018[14:05:54]

 SLAB DESIGN :- Drawing Room
Edges conditions :- (All four edges contineous)

Room Size :- 14 x 15.5 Ft. Thickness of Slab :- 125 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1.2 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 8.90 7.64 KN-m/m
For positive moments (at bottom) Mid Span:- 6.73 5.73 KN-m/m
Maximum R/F(Flexural Consideration) :- 355.92 mm2/m, 10 mm dia. 221 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 251.36 mm2/m 10 mm dia. 300 mm c/c
Bottom At Mid Span : 186.64 mm2/m 10 mm dia. 300 mm c/c
UP
Long Span
Top At support :- 239.40 mm2/m 10 mm dia. 285 mm c/c
Bottom At Mid Span : 176.06 mm2/m 10 mm dia. 285 mm c/c

Minimum R/F :- 150.00 mm2/m 8 mm dia 335 mm c/c

Maximum Spacing :- 285 mm

10 mm dia.
8" c/c

10 mm dia.
7" c/c

382539833.xlsx[[2] 8/12 03/25/2018[14:05:54]

 UP

382539833.xlsx[[2] 9/12 03/25/2018[14:05:54]

 SLAB DESIGN :- Backside Bed Room
Edges conditions :- (Two short edges contineous)

Room Size :- 15.5 x 17 Ft. Thickness of Slab :- 145 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1.2 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 0.00 14.01 KN-m/m
For positive moments (at bottom) Mid Span:- 13.24 10.90 KN-m/m
Maximum R/F(Flexural Consideration) :- 558 mm2/m, 10 mm dia. 141 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 0.00 mm2/m #DIV/0!
Bottom At Mid Span : 315.48 mm2/m 10 mm dia. 240 mm c/c
Long Span
Top At support :- 370.40 mm2/m 10 mm dia. 210 mm c/c
Bottom At Mid Span : 281.48 mm2/m 10 mm dia. 270 mm c/c

Minimum R/F :- 174 mm2/m 8 mm dia 289 mm c/c

Maximum Spacing :- 300 mm

10 mm dia.
6" c/c

10 mm dia.
5" c/c

UP
382539833.xlsx[3] 10/12 03/25/2018[14:05:54]
 SLAB DESIGN :- Study Room
Edges conditions :- (One long edge discontineous)

Room Size :- 9 x 10.5 Ft. Thickness of Slab :- 125 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1.2 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 4.67 3.75 KN-m/m
For positive moments (at bottom) Mid Span:- 3.49 2.84 KN-m/m
Maximum R/F(Flexural Consideration) :- 254.92 mm2/m, 8 mm dia. 197 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 126.06 mm2/m 8 mm dia. 300 mm c/c
Bottom At Mid Span : 93.45 mm2/m 8 mm dia. 300 mm c/c
Long Span
Top At support :- 109.39 mm2/m 8 mm dia. 294 mm c/c
Bottom At Mid Span : 82.13 mm2/m 8 mm dia. 294 mm c/c

Minimum R/F :- 150.00 mm2/m 8 mm dia 335 mm c/c

Maximum Spacing :- 294 mm

8 mm dia.
7" c/c

8 mm dia.
7" c/c

382539833.xlsx[4] 11/12 03/25/2018[14:05:54]

 SLAB DESIGN :- Kitchen
Edges conditions :- (One long & one short edge discontineous)

Room Size :- 9 x 15.5 Ft. Thickness of Slab :- 125 mm

Concrete Grade M-15 (fck 15 N/Sqm) Steel :- HYSD (fy 415 N/Sqm)
Live Load :- 3.5 KN/Sqm
Floor Finish + Other Load :- 1.2 + 0.5 KN/Sqm
Calculated BM per unit width of slab are as follows;
Mx My
For negative moments (at top) Support :- 8.32 4.76 KN-m/m
For positive moments (at bottom) Mid Span:- 6.23 3.55 KN-m/m
Maximum R/F(Flexural Consideration) :- 341.01 mm2/m, 8 mm dia. 147 C/C
Required Reinforcements & Spacing
Short Span
Top At support :- 231.25 mm2/m 8 mm dia. 210 mm c/c
Bottom At Mid Span : 170.40 mm2/m 8 mm dia. 290 mm c/c
Long Span
Top At support :- 140.21 mm2/m 8 mm dia. 294 mm c/c
Bottom At Mid Span : 103.29 mm2/m 8 mm dia. 294 mm c/c

Minimum R/F :- 150.00 mm2/m 8 mm dia 335 mm c/c

Maximum Spacing :- 294 mm

8 mm dia.
8" c/c

8 mm dia.
5" c/c

382539833.xlsx[5] 12/12 03/25/2018[14:05:54]