Scribd
Upload
63 views

NBNWirelessRouter Final

This document provides instructions for configuring a wireless router for an NBN connection. It includes steps to physically connect the router, configure the network settings on your computer, access the router's administrative settings via a web browser, set the WAN connection to PPPoE and enter the username and password, and configure the wireless network name and password. It also provides information on changing the wireless password for added security and notes that it may take 10-15 minutes for the new password to take effect on the router after changing it online.

Uploaded by

tori
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
63 views

NBNWirelessRouter Final

This document provides instructions for configuring a wireless router for an NBN connection. It includes steps to physically connect the router, configure the network settings on your computer, access the router's administrative settings via a web browser, set the WAN connection to PPPoE and enter the username and password, and configure the wireless network name and password. It also provides information on changing the wireless password for added security and notes that it may take 10-15 minutes for the new password to take effect on the router after changing it online.

Uploaded by

tori
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Configuration Guide NBN Wireless Router

NBN Wireless Router

IMPORTANT MESSAGE

Your router has been pre-configured, you do not need to


follow each step of the set-up guide but should retain this
document in case you need to manually configure your
equipment.

To configure your PC/Laptop with your wireless password including


changing your wireless password, please proceed to step 4.

Contents
1. Physical Connection
2. Network Configuration
3. Configuring Internet
4. Configuring Wireless
5. Change of Password

1. PHYSICAL CONNECTION

Please refer to the Quick Reference Guide.

PLEASE NOTE: Have your router powered on and connected directly to your
PC via Ethernet Cable before you begin, as these instructions are based on
wired Ethernet connection

2. NETWORK CONFIGURATION

PPPoE connection does not require you to have an IP address or DNS


settings manually encoded on your network card.
PPPoE connection uses authentication to establish the Internet
connection and its after doing this that your router is assigned an
IP and DNS settings from TPG.

To begin, your PC needs to receive a private IP address from the


router. Most NBN routers have DHCP enabled by default that
will take care of this.

1
Configuration Guide NBN Wireless Router

To ensure your Network Card is ready for this, please follow the
following steps:

 lick on Start -> Control Panel -> Network and Internet ->
A. C
Network and Sharing Center -> Change adapter settings
B. Right click on Local Area Connection and select Properties

C. Double Click on Internet Protocol Version 4 (TCP/IPv4) ->


Properties

D. Ensure “Obtain an IP address automatically” is selected


E. Ensure “Obtain DNS server address automatically” is selected
F. Click OK

2
Configuration Guide NBN Wireless Router

3. CONFIGURING ROUTER

A. O
 pen your browser and in the address bar type
http://192.168.1.1 and press Enter

 nter admin for both the username and password


B. E
and click OK. If you have changed the login credentials,
please enter the current username and password for
your router interface.

C. Click on the WAN tab. Change WAN type to “PPP over


Ethernet”

 nter your TPG username and password.


D. E
Click Save and apply the changes

E. Quick Setup complete! The setup wizard is completed.

3
Configuration Guide NBN Wireless Router

4. CONFIGURING WIRELESS

Things you need to know before you begin:

By default the NBN Wireless Router that you purchased


from TPG is configured with the following wireless security
settings:

SSID (name for the wireless connection):


TPG-xxxx (xxxx is a random 4 digit alpha numeric code)

Authentication Type: WPA-PSK/WPA2-PSK

Encryption: TKIP/AES

Pre Shared Key: initially configured to be the same as


your TPG password. You can enter your own text as an
option.

To use Wireless be sure that you already have set up your


wireless adapter.

A. Click
 Start -> Control Panel -> Network and Internet
-> Network and Sharing Center -> Change adapter
settings

 ight click on Wireless Network Connection and


B. R
click ‘Connect/Disconnect’

C. Find the SSID (network name) of your router and click


Connect. By the default, the network name should
be TPG-xxxx (xxxx is a random 4 digit alpha numeric
code).

 ou will now be prompted to enter your WPA Key /


D. Y
wireless password. This is the same as your TPG
password if you did not change it on the router.

E. Click OK.

4
Configuration Guide NBN Wireless Router

F. You should now see your status as ‘Connected’.

5. CHANGE OF PASSWORD

For security purposes we highly recommend that you change


your password if you are using your default or
if you believe your password security has been compromised.

To change your password, first please visit https://cyberstore.


tpg.com.au/your_account/?function=changepassword.

Your new password will take approximately 10-15 minutes


to take effect, after which you must reconfigure your new
password in your router.

PLEASE NOTE:
Each time your router is powered on, it will initialize this automated authentication process after which your router will receive
a public IP address (fixed or dynamic depending on your plan) and DNS settings from TPG.

tpg.com.au/support 13 14 23
5

You might also like