Scribd
Upload
140 views1 page

Calibration Result Judgement Check Sheet

This document is a calibration result judgment sheet from Honda Malaysia evaluating the performance of equipment. It records 10 test point readings with the measured values, uncertainties, and differences from the standard. A graph compares the errors to the equipment and production tolerances. The conclusion is that errors within the tolerances indicate the equipment is suitable for production use, while exceeding tolerances means it is not suitable. The sheet finds the equipment's accuracy is acceptable in this test.

Uploaded by

Amirul Hafiz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
140 views1 page

Calibration Result Judgement Check Sheet

This document is a calibration result judgment sheet from Honda Malaysia evaluating the performance of equipment. It records 10 test point readings with the measured values, uncertainties, and differences from the standard. A graph compares the errors to the equipment and production tolerances. The conclusion is that errors within the tolerances indicate the equipment is suitable for production use, while exceeding tolerances means it is not suitable. The sheet finds the equipment's accuracy is acceptable in this test.

Uploaded by

Amirul Hafiz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Honda Malaysia Sdn Bhd Section-Wide Form

Dept/ Section QI
Calibration Result Judgment Sheet Document No. F-SW-QI-020
Revision No. 00

Date issue Cert No.


Equipment Name Calibrator/ Supplier
ID No. Calibration Date
Series No. Next Calibration Date

Equip. Accuracy/Tolerance Uncertainty ±


Range Used Production Tolerance ±

UUT Setting Std Reading Error Uncertainty U Equipment Tolerance Production Tolerance
No.
-U +U Lower (-) Upper (+) Lower (-) Upper (+)
1 0.00 0.00 0.00 0.00 0.00 0.00 0.00
2 0.00 0.00 0.00 0.00 0.00 0.00 0.00
3 0.00 0.00 0.00 0.00 0.00 0.00 0.00
4 0.00 0.00 0.00 0.00 0.00 0.00 0.00
5 0.00 0.00 0.00 0.00 0.00 0.00 0.00
6 0.00 0.00 0.00 0.00 0.00 0.00 0.00
7 0.00 0.00 0.00 0.00 0.00 0.00 0.00
8 0.00 0.00 0.00 0.00 0.00 0.00 0.00
9 0.00 0.00 0.00 0.00 0.00 0.00 0.00
10 0.00 0.00 0.00 0.00 0.00 0.00 0.00

Unit for x & y axis : 0


1.00 Error Value
0.90

0.80

0.70
Equipment Tolerance (+ve)
0.60
Test Point Equipment Tolerance (-ve)
0.50
Production Tolerance (+ve)
0.40 Production Tolerance (-ve)

0.30 Error/Uncertainty

0.20

0.10

0.00
0.00 0.20 0.40 0.60 0.80 1.00 1.20

(Acceptable Measurement Error and Uncertainty shall not exceed than Production Tolerance)
Reference Standard/Master used :
Reference Standard Name Serial No. Calibration Due Date Traceable to

Remark/Note (conclusion of the graph analysis result, mark at below graph situation ) :
Error and uncertainty are within the value of Error and/or uncertainty are exceed then equipment
1 equipment tolerance and production tolerence 3
tolerance and production tolerance
REMARK : SITUATION ① AND ② EQUIPMENT ACCURACY ARE OK, CAN BE USE FOR PRODUCTION PURPOSE, FOR SITUATION ③
Error and uncertainty are exceed then equipment
2 tolerance but within the production tolerance
EQUIPMENT NOT SUITABLE TO BE USE AT PRODUCTION

Judgment : OK / OK with condition / NG (circle for related judgment)

Statement for Judgment :

Checked Prepared

Approved (HOD) Approved (CIE)


Retention period for this document : 10 Years

You might also like