Training Material of MS82CT Chassis

1
 Table of Contents Page
z Interface Introduction…………………………………………………………….……..3
z Main Chip Introduction………………………………………………………….……....4
z Key Components Introduction ………………………………………….………….…5
z Key Components List………………………………………………………………..…..6
z Signal Flow Diagram……………………………………………………………….…….7
z Key test point………………………………………………………………….………....10
z Unit Circuit Analysis and Testing ……………………………………………….……18
z Trouble Shooting……………………………………………………………………...…30
z Software update from USB ………………………………………………………….....33
z Enter factory menu method and system reset method…………………………....35

2
 Interface Introduction

Power To tcon
Supply or source
Socket board
To left
speaker

To right
Audio R Audio L Video speaker
of AV1 of AV1 of
SPDIF Vide
IN IN AV1
OUT o To
IN
OUT key&ir
board

USB HDMI VGA Audio R Audio L Pr Pb Y/Video Tuner

IN IN IN IN IN IN IN of AV2 IN
(YPbPr&A (YPbPr&A IN
V2&VGA) V2&VGA)

3
Main Chip Introduction
The MST6M182VG is MSTAR’s most up-to-date system-on-chip solution and most cost-
effective solution for flat panel TV..
It integrates TV/muti-media all purpose AV decoder,VIF demodulator,and advanced
Sound/Video processor into a single device.For standard users,the MST6M182VG provides
multi-standard analog TV support with 3D video decoding and VBI data extraction.The build-
in audio decoder is capable of decoding FM,AM,A2,BTSC and EIA-J sound standards.
World-Leading Audio/Video Technology: The MST6M182VG supports Full-HD
MPEG1/2/4/DiviX/VC1/RM/H.264/AVS video decoder standards, and JPEG,BMP,PNG.
Rich Features for High Value Products: The MST6M182VG family enables true single-
chip experience. It integrates DDR, TCON etc.

4
 Key Components Introduction
DC-DC LDO LDO
5V to 5V to 5V to
VDDC( 1V8 3V3_NORMAL
1.26V)

DC-DC
12V to5V

Flash 5V to 5V to
2V5 TU_3V3

Audio MOSFET
Amplifier silicon
12V to5V tuner IC o
Main IC board

5
Key Components List
Part No. Component Type / Model location
MOSFET-SMD N 30V 10.4AA 3.57W
12-13N03L-0BX 12V to 5V MOSFET Q110
SO8 PHKD13N03LT
13-AS1117-18B 5V to 1V8 LDO ICSOT-223 AS1117-18CX U101

13-AS1117-25B 5V to 2V5 LDO IC SOT-223 AS1117-25 CX U102

5V to 3V3_NORMAL
13-AS1117-33B IC 3.3V SOT-223 AS1117-33 CX U103
LDO
13-AS1117-33B 5V to TU_3V3 LDO IC 3.3V SOT-223 AS1117-33 CX U201
13-EN25Q3-2BBEO Flash IC 32M BIT SERIAL FLASH EN25Q32B U503
5V to VDDC(1V26)
13-G5193R-41B IC 5V TO 1.2V G5193 U104
DC-DC
IC A SINGLE CHIP SUPORT
13-MST6E1-82BVG SOC U501
MULTIMEDIA TV SOC MST6E182VG
13-RT8110-B0B 12V to 5V DC-DC IC DC/DC转换I 贴片 RT8110B U105
13-T18273-HNB Silicon Tuner IC SILICON TUNER IC TDA18273HN U202
13-TDA151-7PP Audio Amplifier IC TDA1517P U601

6
Signal Flow Diagram

7
Power Supply Flow

8
I²C Bus Block Diagram

P400
H1-SCL
HDMI input
H1-SDA
Socket U501 Tuner-SCL U202
SOC Tuner-SDA Silicon Tuner
UART-RX MST6M182VG TDA18273HN
P402
UART-TX
VGA input
Socket

9
Key test point
P105
The Key Test Point of Power Supply chassis
Power
supplier
When TV set working normally, the voltage of each pin of P105 is like below:
Pin 1 and PIN2 : dim signal ,3V3 when backlight adjust to max. valut 100
Pin 3 and PIN4 : 3V3
Pin 5 and PIN6 : 3V3
Pin 7 and PIN8 : 3V3
Pin 9,PIN10 and PIN12 : GND
PIN11,PIN13 and PIN14 :12V
11
The Key Test Point of 12V to 5V

Q110
MOSFET U105
DC-DC

5V
OUT

12V
IN

L100
Output
inductance
The Key Test Point of 12V to 5V
The Key Test Point of 5V—VDDC
C111,C112 :5V
input
capacitance

U104
DC-DC

C107 ,C113,C120
1.26V output
capacitance

L102
Output
inductance

14
The Key Test Point of 5V—VDDC

15
The Key Test Point of 5V—3V3_NORMAL&2V5&1V8

U103

U101

U102

16
The Key Test Point of 5V—TU_3V3

U201

17
Unit Circuit Analysis and Testing
From PSU
a. Power-up sequence：
Pin A10 of
U501

AC Input, power board operates and

provides a 3V3_STB to the main board, TV To PSU
set is in standby mode, and the indicator on.

Press the power button of remote control or front control board to turn on the set, the Indicator
off.

Main IC provide a high level through pin A10 of u501, across R128,then directly send to power
board.

Then the power board output main board power 12V .

18
 b. Backlight Switch signal and Dim adjust signal
Pin B10 of U501 sends out a high or low level, across R126, then directly send to power
board through pin3&pin4 of P105 of the main board, control the backlight on or off.

Pin B12 of U501 sends out PWM signal, across R124 ,then directly sends to power board
through pin 1a&pin 2 of the main board, adjust back light brightness.

Pin B12 of
U501
Pin B10 of
U501

19
b. Backlight Switch signal and Dim adjust signal
Dim waveform when customer set backlight into 100 at customer menu

20
b. Backlight Switch signal and Dim adjust signal
Dim waveform when customer set backlight into 50 at customer menu

21
b. Backlight Switch signal and Dim adjust signal
Dim waveform when customer set backlight into 0 at customer menu

22
c. Reset Circuit Analysis and Testing

Q500
system
reset test

high level is reset.

When 3V3_STB comes, it charge C503 through R501 ,Q500 turns on,when the voltage of C503
is charged about 2.6v ,the Q500 start to turn off. Reset process finished.

23
c. Reset Circuit Analysis and Testing
Chanel1 is reset signal and chanel2 is 3v3_stb voltage,reset high level is active
And the reset pulse width is about 61 ms

24
d. Mute Circuit
The circuit diagram is as follows

25
d. Mute Circuit
But the active circuit diagram is as below

Amp_reset is from the pin C9 of SOC U501,it control TV set mute

when the ‘mute’ button of remote control is press,
but when AC power on/off
The audio amplifier is muted by charge or de-charge C614 through R609

26
 d. Mute Circuit
Mute pin and 12v Waveform when Mute pin and 12v Waveform when
Remote power on,delay about Remote power off,delay about
627ms 1350ms

27
e. Audio Output Circuit

28
TDA1517P internal block diagram as below,

29
 Trouble Shooting

Don’t start
Check power No Is Power board 3.3V
board STB, 12V normal?

YES Only3.3V Yes

Check if every DC-DC

Shift module has
No Check every
Check if main chip output. Does main IC have DC-DC module
power supply or not
Output Pow-ON, Dim,
BL-ON Signal to Yes
power board Main IC reset signal
No Check the U500(main IC)
Peripheral components
/ upgrade main software / IIC bus signal
check whether it connect
ground well /
Check UART LOG Crystal work or not

Yes

Replace U501

30
Trouble Shooting
Abnormal Picture

Abnormal picture To check which source Abnormal picture

in some of source has abnormal picture in all source

Check the U501

relevant signal Check the circuit
Problem between U500 to
source circuit.
panel

TV, AV, YPbPr, Check the row-resistor, Check the LVDS

HDMI, VGA Replace cap. and copper of connector and T-con
U501 circuit is OK? board and panel.

Check peripheral
components of U501

31
Trouble Shooting
Abnormal Sound or No Sound

Abnormal sound To check which source Abnormal sound in all

in some of source. has abnormal sound. source.

Check the input waveform of Y Check U601

Check the input Y U601. OK? or Speakers.
coupling circuit .
OK? N

Check the status of U501 Y Check the

N output. OK? status of
middle circuit
N
Check the N Check the input coupling
relevant signal circuit of U501. OK?
source circuit.
Y

Replace U501

32
Software update from USB:
1) Please ensure the software you are using has a correct file
name
TCL_MS82_UPDATE.bin, then copy it to the root directory of a
USB disk.
2) Insert the USB disk to the USB socket of the set for which you
are
going to upgrade program.
3) Enter the Factory Menu (you can choose either a or b way
below)
a. In the first place, press Menu button of remote
control, then select Contrast item of Picture
submenu. Finally, press 9, 7, 3, 5 consecutively.
b. When the Factory hotkey item of Factory Menu
is enabled (ON), press Return button of remote
Control.

33
Software update from USB:
4) select USB UPDATE, press buttonof remote control, a pop
menu
will appear prompting whether start upgradeor not. Press Yes to
start upgrade,
press No to canel. Please wait patiently until the set restart
automatically after
upgrade. Do not cut off the power supply during the process.

34
Enter Factory menu method:
Follow the below steps to pop-up the Factory Menu in case of
“FactoryKey” is disable:
- press RemoteControl key “MENU” to display main menu
- Select “Picture” and press “OK” key to enter the picture
submenu
- Select “Contrast” item
- press the subsequence RemoteControl keys “9”, “7”, “3” and “5”
Press RemoteControl key “Return” To pop-up the Factory Menu
in case of “FactoryKey” is enable.
The status of “Factory Key” can be changed in Factory Menu-
>Hotkey
Press RemoteControl “OK” key or “RIGHT” key to enter the
submenu.
Press RemoteControl “Menu” key to go back to the root menu.
Press RemoteControl “RIGHT”or “LEFT” key to change the
values.
Press RemoteControl “OK” key run the function.
Press RemoteControl “Exit” key exit the factorymenu.

35
System reset method:
Enter Factory Menu
- Select “Reset all” item
-Press RemoteControl “OK”, TV will reset system data.
Illustrate as blow:

36