MO Class Parameter Id Parameter Name

LNBTS 53031 DL AMC CQI Comp For Dynamic OL MIMO SM With RI1

LNBTS 53033 DL AMC CQI Comp For Dynamic OL MIMO TXdiv With RI2

LNBTS 53038 DL AMC CQI Ageing Factor

LNBTS 53039 DL AMC Timer For Historical CQI

LNBTS 53040 Time Avg Constant For Equal Throughput Criterion In DL

LNBTS 53041 AM RLC Maximum Retransmission Treshold DRB

LNBTS 53043 DRB Downlink Scheduling Priority

LNBTS 53044 Enable PHICH Ctrl UL

LNBTS 53045 ENB Name

LNBTS 53046 Uplink Improved Latency Minimum Data Volume

LNBTS 53047 Uplink Improved Latency Reaction Timer

LNBTS 53048 Instance Identifier Of Object LNBTS

LNBTS 53050 Local State

LNBTS 53052 Maximum Number Of PRBs For Scheduling Request Users

LNBTS 53053 Max S1 Reset Retries

LNBTS 53054 Max S1 Setup Retries

LNBTS 53055 Max X2 Reset Retries

LNBTS 53056 Max X2 Setup Retries

LNBTS 53057 MCC In PLMN

LNBTS 53063 Averaging Filter Constant For CQI Measurements

LNBTS 53064 CQI Compensation When Reported RI=2

LNBTS 53065 Averaging Filter Constant For RI Measurements

LNBTS 53066 MNC In PLMN

LNBTS 53067 MNC Length In PLMN

LNBTS 53068 Operational State

LNBTS 53069 PDCP Profile List

LNBTS 53070 PDCP Profile Id

LNBTS 53071 PDCP Status Report Required

LNBTS 53072 PDCP Timer Discard

LNBTS 53073 Scheduling Priority Of HARQ Retransmission In Downlink

LNBTS 53074 Scheduling Priority Of HARQ Retransmission In Uplink

LNBTS 53075 Scheduling Priority Of The Scheduling Request Procedure

LNBTS 53076 Scheduling Priority Of SRB In Downlink

LNBTS 53077 Scheduling Priority Of SRB In Uplink

LNBTS 53078 QCI Translation Table

LNBTS 53079 DSCP

LNBTS 53080 Packet Delay Budget

LNBTS 53081 Packet Loss Rate

LNBTS 53082 PDCP Profile Id In QCI Table

LNBTS 53083 Priority

LNBTS 53084 QCI

LNBTS 53085 QCI Support

LNBTS 53086 Resource Type

LNBTS 53087 RLC Mode

LNBTS 53088 RLC Profile Id In QCI table

LNBTS 53089 UL Scheduling - Bucket Size Duration (BSD)

LNBTS 53090 UL Scheduling - Priority

LNBTS 53091 Large Size Random Access MCS In Uplink

LNBTS 53092 Large Size Random Access Data Volume In Uplink

LNBTS 53093 Small Size Random Access MCS In Uplink

LNBTS 53094 AM RLC DRB Profile List

LNBTS 53096 AM RLC Poll PDU DRB

LNBTS 53097 RLC Profile Id

LNBTS 53098 AM RLC Timer Poll Retransmit DRB

LNBTS 53099 AM RLC Timer Status Prohibit DRB

LNBTS 53100 AM RLC Timer Reordering DRB

LNBTS 53101 Number Of Succesful PDSCH Transmissions

LNBTS 53102 Number Of Failed PDSCH Transmissions

LNBTS 53103 Time Frame For Failed PDSCH Transmissions

LNBTS 53104 RRC Guard Timer Radio Bearer Management

LNBTS 53105 Timer S1 Reset Wait For Response

LNBTS 53106 Timer S1 Setup Wait For Response

LNBTS 53107 TDATA Fwd S1

LNBTS 53108 TDATA Fwd X2

LNBTS 53109 Timeout For Establishment Of Ue Associated S1 Sign Conn

LNBTS 53110 Timer Min Lifetime Of Half Open Rrc Connection

LNBTS 53111 T HO Overall Delta

LNBTS 53112 Timer Missing L2 Ack For Rrc Connection Release

LNBTS 53113 TX2 RELOC Comp

LNBTS 53114 TX2 RELOC Exec Delta

LNBTS 53115 Handover Cancel Latency Timer

LNBTS 53116 TX2 RELOC Prep

LNBTS 53117 Maximum Number Of Time Alignment Command Retries

LNBTS 53118 Time Alignment Offset Margin For Scheduling

LNBTS 53122 TX2 RELOC Overall Delta

LNBTS 53123 UL AMC Delta C Stepsize Up

LNBTS 53124 UL AMC Initial Delta C

LNBTS 53125 UL AMC Max Delta C

LNBTS 53126 UL AMC Min Delta C

LNBTS 53127 UL AMC Timer For Historical MCS

LNBTS 53128 UL AMC Inactivity Timer

LNBTS 53129 UL AMC Factor For Upgrade And Downgrade

LNBTS 53130 UL ATB PHR Averaging Factor

LNBTS 53131 Time Avg Constant For Equal Throughput Criterion In UL

LNBTS 53133 Timer X2 Reset Wait For Response

LNBTS 53134 Timer X2 Setup Wait For Response

LNCEL 53259 A3 Offset

LNCEL 53260 A3 Report Amount

LNCEL 53261 A3 Report Interval

LNCEL 53262 A3 Time To Trigger

LNCEL 53263 A5 Report Amount

LNCEL 53264 A5 Report Interval

LNCEL 53265 A5 Threshold 1

LNCEL 53266 A5 Threshold 2

LNCEL 53267 A5 Time To Trigger

LNCEL 53268 Access Barred For Mobile Terminating Calls

LNCEL 53269 Access Class Barring Time

LNCEL 53270 Access Probability Factor

LNCEL 53272 Additional Spectrum Emission Mask

LNCEL 53274 Neighbouring Cell Information List

LNCEL 53275 E-Utran Cell Identitiy Of Adjacent Cell

LNCEL 53276 Administrative State

LNCEL 53279 Cell Reselection Timer Factor High Mobility

LNCEL 53280 Cell Reselection Timer Factor Medium Mobility

LNCEL 53281 Cell Barred Flag

LNCEL 53283 Cell Reselection Priority

LNCEL 53285 Cell Reserved For Operator Use

LNCEL 53286 Cell Scheduling Request Periodicity

LNCEL 53287 Enable Aperiodic CQI reporting On PUSCH

LNCEL 53288 Aperiodic CQI Feedback Reporting Mode

LNCEL 53289 Timer For Aperiodic CQI / PMI Feedback Requesting

LNCEL 53294 Periodic CQI Feedback Reporting Mode

LNCEL 53295 Reporting Period Of Periodic CQI / PMI Feedback

LNCEL 53296 Periodic Subband CQI Cycles K

LNCEL 53297 Enable Simultaneous CQI And ACK/NACK

LNCEL 53298 Cyclic Prefix Length In DL And UL

LNCEL 53299 DeltaF PUCCH List

LNCEL 53300 DeltaF PUCCH Format 1

LNCEL 53301 DeltaF PUCCH Format 1b

LNCEL 53302 DeltaF PUCCH Format 2

LNCEL 53303 DeltaF PUCCH Format 2a

LNCEL 53304 DeltaF PUCCH Format 2b

LNCEL 53310 Dedicated SR Transmission Maximum

LNCEL 53311 Default Paging Cycle

LNCEL 53316 Delta Preamble Random Access Message 3

LNCEL 53317 Delta Cyclic Shift For PUCCH

LNCEL 53318 Enabled TB Size Impact To UE PUSCH Power Calculation

LNCEL 53319 Enable 64QAM In Downlink

LNCEL 53320 Cell Power Reduce

LNCEL 53321 Downlink Channel Bandwidth

LNCEL 53323 Downlink MIMO Mode

LNCEL 53324 Enable OLQC

LNCEL 53325 Downlink Pathloss Change

LNCEL 53327 DL Target BLER

LNCEL 53329 Default CQI

LNCEL 53330 Enable DL AMC

LNCEL 53332 MIMO Compensation

LNCEL 53334 Use Of Partly Allocated PRBs

LNCEL 53337 Access Barred For Emergency Calls

LNCEL 53338 EARFCN Downlink

LNCEL 53339 EARFCN Uplink

LNCEL 53341 Enable Better Cell HO

LNCEL 53342 Enable Coverage HO

LNCEL 53343 E-UTRAN Cell Identifier

LNCEL 53345 Filter Center Tx

LNCEL 53346 Filter Coefficient

LNCEL 53348 Further PLMN Identity List

LNCEL 53349 Mobile Country Code

LNCEL 53350 Mobile Network Code

LNCEL 53351 Mobile Network Code Length

LNCEL 53352 Group Assignment For PUSCH

LNCEL 53353 Maximum Number Of Message 3 HARQ Transmissions

LNCEL 53354 Maximum Number Of HARQ Transmission In DL

LNCEL 53355 Maximum Number Of HARQ Transmission In UL

LNCEL 53357 Hopping Bandwidth Of PUSCH

LNCEL 53358 Hopping Mode Of PUSCH

LNCEL 53364 HW State

LNCEL 53367 Inactivity Timer

LNCEL 53368 UE Sounding RS Duration

LNCEL 53369 Initial MCS In Downlink

LNCEL 53370 Initial MCS In Uplink

LNCEL 53372 Initial Amount Of PRBs In Uplink

LNCEL 53373 Intra-Frequency Blacklisted Cell List

LNCEL 53375 Number Of PCI In The Intra Frequency Range

LNCEL 53376 Lowest PCI In The Intra Frequency Range

LNCEL 53377 Intra-Frequency Neighbouring Cell List

LNCEL 53378 Physical Cell Identifier In Neighbouring Cell List

LNCEL 53379 Cell Reselection Procedure Offset

LNCEL 53380 Intra Frequency Cell Reselection Allowed

LNCEL 53382 Presence Antenna Port1

LNCEL 53383 Local Cell Resource ID

LNCEL 53384 Instance Identifier Of Object LNCEL

LNCEL 53385 Local State

LNCEL 53387 Maximum Bitrate Downlink

LNCEL 53388 Maximum Bitrate Uplink

LNCEL 53389 Maximum Coderate For Paging

LNCEL 53390 Maximum Coderate For Random Access Messge 4

LNCEL 53391 Maximum Coderate For Random Access Messge 2

LNCEL 53392 Maximum Coderate For SIB

LNCEL 53394 Maximum Number of OFDM Symbols for PDCCH

LNCEL 53395 Maximum Number Of Active UE Including Handover

LNCEL 53396 Maximum Number Of Active UEs

LNCEL 53399 Maximum Number Of RRC Connections

LNCEL 53400 Maximum Amount Of Users Per TTI In DL

LNCEL 53401 Maximum Amount Of Users Per TTI In UL

LNCEL 53405 Maximum Bitrate Selector

LNCEL 53406 MBSFN Neighbour Cell Configuration

LNCEL 53419 CQI Threshold For Fallback To MIMO Diversity

LNCEL 53420 CQI Threshold For Activation Of OL MIMO SM

LNCEL 53422 Rank Threshold For Fallback To MIMO Diversity

LNCEL 53423 Rank Threshold For Activation Of OL MIMO SM

LNCEL 53424 Minimum Bitrate Downlink

LNCEL 53425 Minimum Bitrate Uplink

LNCEL 53426 Modification Period Coefficient

LNCEL 53427 ACK/NACK Offset

LNCEL 53428 Maximum Number Of Out-Of-Sync Indications

LNCEL 53429 Maximum Number Of In-Sync Indications

LNCEL 53431 Number Cell Changes High Mobility

LNCEL 53432 Number Cell Changes Medium Mobility

LNCEL 53434 PUCCH Bandwidth For CQI

LNCEL 53435 Nom PdschRs Epre Offset

LNCEL 53438 Number Of Transmission Antenna Ports

LNCEL 53439 Access Class Barring List For Mobile Originating Calls

LNCEL 53441 Access Class Barring Time For Originating Calls

LNCEL 53442 Access Probability Factor For Originating Calls

LNCEL 53443 Operational State

LNCEL 53444 Nominal Power For UE PUCCH Tx Power Calculation

LNCEL 53445 Nominal Power For UE PUSCH Tx Power Calculation

LNCEL 53448 Power Offset For UE PUCCH Tx Power Calculation

LNCEL 53449 Power Offset For UE PUSCH Tx Power Calculation

LNCEL 53451 Maximum Output Power

LNCEL 53452 Paging nB

LNCEL 53453 PDCCH Aggregation For Paging

LNCEL 53455 PDCCH Aggregation Level For Preamble Assignments

LNCEL 53457 PDCCH Aggregation For Random Access Response Message

LNCEL 53458 PDCCH Aggregation For Secondary System Information

LNCEL 53460 PHICH Duration

LNCEL 53461 PHICH Resource

LNCEL 53463 Physical Layer Cell Identity

LNCEL 53469 PRACH Cyclic Shift

LNCEL 53470 PRACH Configuration Index

LNCEL 53471 PRACH Frequency Offset

LNCEL 53472 PRACH High Speed Flag

LNCEL 53473 Power Ramping Step

LNCEL 53474 Preamble Transmission Maximum

LNCEL 53480 PUCCH Cyclic Shift For Mixed Formats

LNCEL 53482 PUSCH Decoding Offset Index For ACK

LNCEL 53483 PUSCH Decoding Offset Index For CQI

LNCEL 53484 PUSCH Hopping Offset

LNCEL 53485 PUSCH Decoding Offset Index For RI

LNCEL 53486 Cell Reselection Procedure Hysteresis Value

LNCEL 53487 Cell Reselection Hysteresis High Mobility

LNCEL 53488 Cell Reselection Hysteresis Medium Mobility

LNCEL 53489 Minimum Required RX Level in the cell

LNCEL 53490 Min Required RX level for intra-freq neighbouring cells

LNCEL 53491 Random Access Backoff

LNCEL 53492 Maximum Content Resolution Timer

LNCEL 53493 C-RNTI Reuse Timer

LNCEL 53498 RA Message Power Offset For Group B Selection

LNCEL 53499 Number Of Random Access Preambles

LNCEL 53501 RA Power Ramping Setup

LNCEL 53502 Random Access Preambles Group A Size

LNCEL 53505 Random Access Response Window Size

LNCEL 53508 Small Size Random Access Data Volume In Uplink

LNCEL 53509 Rank Indication Reporting Enable

LNCEL 53510 Multiplier M For Periodic Ri Reporting Period

LNCEL 53511 Periodic RI Reporting Offset

LNCEL 53512 RACH Root Sequence

LNCEL 53513 Rx Antenna Specific Power Scaling Factor

LNCEL 53514 Intra Frequency Measurements Threshold

LNCEL 53515 Inter Frequency And Inter RAT Measurements Threshold

LNCEL 53516 System Information 2 Mapping Information

LNCEL 53517 System Information 2 Periodicity

LNCEL 53518 System Information 2 Repetition

LNCEL 53519 System Information 3 Mapping Information

LNCEL 53520 System Information 3 Periodicity

LNCEL 53521 System Information 3 Repetition

LNCEL 53522 System Information 4 Mapping Information

LNCEL 53523 System Information 4 Periodicity

LNCEL 53524 System Information 4 Repetition

LNCEL 53525 SI Window Length

LNCEL 53526 Access Class Barring List Mobile Orig Signalling

LNCEL 53528 Access Class Barring Time For Signalling

LNCEL 53529 Access Probability Factor For Signalling

LNCEL 53530 Enable Sounding Reference Signal

LNCEL 53531 Scheduling Weight Downlink For SRB

LNCEL 53532 Scheduling Weight Uplink For SRB

LNCEL 53533 Sounding RS Bandwidth Layer

LNCEL 53534 Sounding RS Bandwidth Configuration

LNCEL 53535 Sounding RS Frequency Hopping

LNCEL 53536 Power Offset For SRS Transmission Power Calculation

LNCEL 53537 Sounding RS Simultaneous To ACK/Nack

LNCEL 53538 Sounding RS Subframe Configuration

LNCEL 53539 SU2 Repetition Period

LNCEL 53540 SW State

LNCEL 53541 Synchronisation Signals Transmission Mode

LNCEL 53542 Timer T300

LNCEL 53543 Timer T301

LNCEL 53544 Timer T302

LNCEL 53545 Timer T304 Intra LTE

LNCEL 53546 Timer T310

LNCEL 53547 Timer T311

LNCEL 53549 Timer TCRmax

LNCEL 53550 Timer TCRmaxHyst

LNCEL 53551 Periodic BSR Time

LNCEL 53552 Periodic PHR Timer

LNCEL 53553 Prohibited PHR Timer

LNCEL 53554 Retransmission BSR Timer

LNCEL 53555 Cell Reselection Timer

LNCEL 53556 Time Alignment Maximum Offset

LNCEL 53557 Time Alignment Timer

LNCEL 53558 Tracking Area Code

LNCEL 53559 Threshold Serving Low

LNCEL 53562 TPC Step Size PUSCH

LNCEL 53563 Tx Power Scaling

LNCEL 53564 Uplink Channel Bandwidth

LNCEL 53565 Enable Uplink Group Hopping

LNCEL 53566 Uplink Reference Signals Cyclic Shift

LNCEL 53568 Uplink Sequence Hopping Enabled

LNCEL 53569 Sequence Shift For PUSCH

LNCEL 53570 UL AMC Target BLER

LNCEL 53571 Enable All TBs In UL AMC

LNCEL 53576 Enable UL AMC EDG And FUG

LNCEL 53577 Enable UL AMC

LNCEL 53580 UL AMC MCS Switch Period

LNCEL 53582 Enable UL ATB

LNCEL 53584 UL ATB Period

LNCEL 53586 PUSCH/PUCCH TPC Commands Accumulation Enabled

LNCEL 53587 Alpha

LNCEL 53588 Preamble Initial Received Target Power

LNCEL 53589 TPC Command In Random Access Response

Abbreviated Name 3GPP Name Description Short Description Range and Step
The parameter defines CQI
cqiCompSmRi1Ol CQI compensation compensation -10...0, step 0.1
The parameter defines CQI
cqiCompTdRi2Ol CQI compensation compensation 0...10, step 0.1
The parameter defines DL AMC
dlamcCqiAgeing CQI ageing factor for ageing factor 0...1, step 0.1
The parameter defines Time in TTIs
dlamcTHistCqi the time in TTIs for for which old 0...1000 TTI, step 1 TTI
Time averaging Time
dlsTputAvgT constant for equal averaging 1...1000 TTI, step 1 TTI
This parameter is used Defines the
by the transmitting side maximum
drbAmMxRtxTh Max_Retx_Threshold 1 (0), 2 (1), 3 (2), 4 (3), 6 (4), 8 (5), 16 (6), 32 (7)
Downlink scheduling Downlink
drbPrioDl priority for DRB for UE Scheduling 1...1000, step 1
The parameter enables Activates
enablePhichCtrlUl / disables the improved enchanged
This is a human Human
enbName eNB Namereadable name for the readable name 1...80 characters
Minimum data volume Minimum data
ilMinDatvolUl which shall be volume which 0...4000 bits, step 80 bits
Improved Latency Improved
ilReacTimerUl Reaction Timer in Latency 0...20000 ms, step 100 ms
This is the instance Instance
lnBtsId identifier
Macro eNB Id of object identifier of 0...1048575, step 1
Local state of the eNB, Local state of
localState value is set by the cell. blocked (0), unblocked (1)
Defines the maximum Maximum
maxNumPrbSr number of PRBs which number of 1...48 PRBs, step 1 PRBs
The maximum number Maximum
maxS1ResetRetries of times that the eNB number of 1...20 number, step 1 number
The maximum number Maximum
maxS1SetRetry of times that the eNB number of 1...20, step 1
The maximum number Maximum
maxX2ResRetry of times that the eNB number of 1...20, step 1
The maximum number Maximum
maxX2SetRetry of times that the eNB number of 1...20, step 1
Primary Mobile Country Mobile Country
mcc Code of eNB Code of eNB 0...999, step 1
Averaging filter Averaging filter
mimoOlCqiAvg constant for open loop constant for 0.05...1, step 0.05
CQI Compensation CQI
mimoOlCqiComp applied to CQI Compensation 0...10, step 0.1
Averaging filter Averaging filter
mimoOlRiAvg constant for open loop constant for 0.05...1, step 0.05
Primary Mobile Mobile
mnc Network Code of eNB Network Code 0...999, step 1
Determines the range Length of MNC
mncLength of primary MNC of eNB in digits of eNB 2...3, step 1
Operational State of Operational
operationalState the eNB, value is set by State initializing (0), commissioned (1), notCommisioned (2), con
Profile of PDCP
pdcpProf parameters PDCP profile
Identity of the PDCP Identity of the
pdcpProfileId profile; 0 specifies an PDCP profile; 0...1, step 1
PDCP Status Report: Determines
statusReportReq This parameter whether a Bit 0: eNB Status Report, Bit 1: UE Status Report,
This parameter PDCP SDU
tDiscard indicates the delay discard timer 50 (0), 100 (1), 150 (2), 300 (3), 500 (4), 750 (5), 1500 (6),
 Scheduling priority of a Scheduling
prioHarqDl HARQ retransmission priority of a 1...1000, step 1
Scheduling priority of Scheduling
prioHarqUl the HARQ priority of the 1...100, step 1
Scheduling priority of Schedulign
prioSrUl the Scheduling Priority of the 1...100, step 1
Scheduling priority of Scheduling
prioSrbDl the Signalling Radio priority of the 1...1000, step 1
Scheduling priority of Scheduling
prioSrbUl the Signalling Radio priority of the 1...100, step 1
Table to translate the Translation
qciTab S1AP parameter QCI table to map
This parameter Configures the
dscp configures the DSCP DSCP value 0...63, step 1
The Packet Delay The Packet
packDelay Budget denotes the Delay Budget 50ms (0), 100ms (1), 150ms (2), 300ms (3)
The Packet Loss Rate The Packet
packLoss determines the rate of Loss Rate 10**-2 (0), 10**-3 (1), 10**-6 (2)
This parameter This parameter
pdcpProfId specifies the ID of a specifies the ID 0...1, step 1
This parameter gives This parameter
prio the priority of the EPS gives the 1...9, step 1
QoS Class
qci QoS Class Identifier Identifier 1...9, step 1
This parameter This parameter
qciSupp indicates whether the indicates NOT_SUPPORTED (0), ENABLED (1), DISABLED (2)
The Resource Type The Resource
resType determines if dedicated Type indidates GBR (0), nonGBR (1)
This parameter This parameter
rlcMode configures the RLC configures the RLC_UM (0), RLC_AM (1), NA (2)
This parameter This parameter
rlcProfId specifies the ID of a specifies the ID 0...1, step 1
The BSD is sent to UE This parameter
ulsBSD for the UL scheduling is used to 50ms (0), 100ms (1), 150ms (2), 300ms (3), 500ms (4), 10
This priority is sent to Priority for UE
ulsPrio priority UE for the UL UL scheduler 0...16, step 1
Defines the modulation MCS to be
raLargeMcsUl and coding scheme used for the 0...15, step 1
Defines the data Data volume
raLargeVolUl volume to be used for assigned for 216...512 bit, step 8 bit
Defines the modulation MCS for the
raSmallMcsUl and coding scheme small size 0...15, step 1
Profile of RLC AM RLC Profile for
rlcProf parameters for DRB DRBs
The AM RLC Poll PDU Number of
pollPdu PollPDU defines the number of RLC PDUs 4 (0), 8 (1), 16 (2), 32 (3), 64 (4), 128 (5), 256 (6), infinity (7
Identity of the RLC AM Identity of the
rlcProfileId profile, 0 specifies an RLC AM 0...1, step 1
This timer is used by Timer for re-
tPollRetr the transmitting side of
T_poll_retransmit transmission of 5 (0), 10 (1), 15 (2), 20 (3), 25 (4), 30 (5), 35 (6), 40 (7), 45
This timer is used by Prohibit Status
tProhib the receiving side of an
T_status_prohibit PDU as long 0 (0), 5 (1), 10 (2), 15 (3), 20 (4), 25 (5), 30 (6), 35 (7), 40 (
This timer is used by Timer for re-
tReord the receiving side of an
T_reordering ordering, PDU 0 (0), 5 (1), 10 (2), 15 (3), 20 (4), 25 (5), 30 (6), 35 (7), 40 (
Determines the number Determines the
rlpDetEndNoDl DL PDSCH number DL 1...20, step 1
Determines the Determines the
rlpDetMaxNoDl maximum number of maximum 0...1000, step 1
Determines the time Determines the
rlpDetMaxTimeDl frame for failed DL time frame for 20...5000 ms, step 1 ms
 This timer is started RRC guard
rrcGuardTimer when an RRC timer for 100...6000 ms, step 100 ms
Vendor Configurable Timout
s1ResetRspTmr Timer that specifies the duration while 0.1...30 s, step 0.1 s
Vendor configurable Timeout
s1SetupRspTmr timer that specifies the duration while 0.1...30 s, step 0.1 s
This timer is started in Data
tDataFwdS1 the source eNB when Forwarding 10...2000 ms, step 10 ms
This timer is normally Data
tDataFwdX2 started in the target Forwarding 10...2000 ms, step 10 ms
Timer to supervise the The minimal
tEstS1Con establishment of a UE- time period 1000...240000 ms, step 1000 ms
The minimal time The minimal
tHalfRrcCon period during which the time period 500...10000 ms, step 500 ms
Covers the estimated Supervision of
tHoOverallD time taken to send an Complete 10...2000 ms, step 10 ms
The minimal time The minimal
tL2AckRrcRel period Indicates the time period 100...2000 ms, step 100 ms
This timer is started in Supervision of
tX2RelocComp the target eNB when Handover 10...2000 ms, step 10 ms
Covers the estimated Supervision of
tX2RelocExcD time taken to Handover 30...5000 ms, step 10 ms
This timer is started in Spare time at
tX2RelocHold the source eNB when source side 10...2000 ms, step 10 ms
This timer is started in Supervision of
tX2RelocPrep the source eNB when Handover 10...2000 ms, step 10 ms
The number of times The number of
taCmdMaxRetry the Timing Advance times the 1...10, step 1
Determines time Determines
taOffScheMarg alignment offset limit time alignment 1...5, step 0.1
Covers at a minimum Supervision of
tx2RelODelta the estimated time Handover 30...2000 ms, step 10 ms
The parameter defines UL OLLA
ulamcCStepUp the stepsize up value Compensation 0...2, step 0.05
The parameter defines UL OLLA initial
ulamcDeltaCini the initial value for Value for -10...10, step 0.1
The parameter defines UL OLLA
ulamcDeltaCmax the maximum limit for maximum Limit 0...10, step 0.1
The parameter defines UL OLLA
ulamcDeltaCmin the minimum limit for minimum -10...0, step 0.1
The parameter defines Time for
ulamcHistMcsT time in TTIs for remembering 0...20000 ms, step 100 ms
The parameter defines UL AMC timer
ulamcInactT the time in TTIs for for Inactivity 10...1000 ms, step 10 ms
The parameter defines UL AMC
ulamcUpdowngrF uplink adaptive Factor to 1...3, step 0.05
The parameter defines UE PHR
ulatbPhrAvgF forgetting factor for UE averaging 0...1, step 0.05
Time averaging Time
ulsTputAvgT constant for equal averaging 1...1000 TTI, step 1 TTI
Vendor configurable Timout
x2ResetRspTmr timer that specifies the duration while 0.1...30 s, step 0.1 s
Vendor configurable Timout
x2SetupRspTmr timer that specifies the duration while 0.1...30 s, step 0.1 s
Handover margin for Handover
a3Offset better cell HO. Used in margin for -30...30 dB, step 1 dB
Defines the maximum Defines the
a3ReportAmount number of maximum 1r (0), 2r (1), 4r (2), 8r (3), 16r (4), 32r (5), 64r (6), infinity (7
Defines the interval Defines the
a3ReportInterval with which interval with 120ms (0), 240ms (1), 480ms (2), 640ms (3), 1024ms (4),
 Time for which the Time for which
a3TimeToTrigger specific criteria for the the specific 0ms (0), 40ms (1), 64ms (2), 80ms (3), 100ms (4), 128ms
Defines the maximum Defines the
a5ReportAmount number of maximum 1r (0), 2r (1), 4r (2), 8r (3), 16r (4), 32r (5), 64r (6), infinity (7
Defines the interval Defines the
a5ReportInterval with which interval with 120ms (0), 240ms (1), 480ms (2), 640ms (3), 1024ms (4),
Receive level threshold Receive level
a5Threshold1 for serving cell in A5 threshold for 0...97 dB, step 1 dB
Receive level threshold Receive level
a5Threshold2 for neighbour cell in A5 threshold for 0...97 dB, step 1 dB
Time for which the Time for which
a5TimeToTrigger specific criteria for the the specific 0ms (0), 40ms (1), 64ms (2), 80ms (3), 100ms (4), 128ms
The Access Barred for Indicates
Mobile Terminating
accesBarrMtCall accessBarringForTerminatingCalls access is
The Access Class Defines the
Barring Time defines
accessClassBarrTaccessClassBarringTime Access Class 4 s (0), 8 s (1), 16 s (2), 32 s (3), 64 s (4), 128 s (5), 256 s (
The Access Probability Defines a
Factor defines a
accessProbFactoraccessProbabilityFactor probability for a 0 (0), 5 (1), 10 (2), 15 (3), 20 (4), 25 (5), 30 (6), 40 (7), 50 (
The Additional Additional
addSpectrEmi Spectrum Emission Spectrum 1...32, step 1
Neighbouring cell Neighbouring
adjCellnfoL information list which cell information
E-Utran Cell Identity of E-Utran Cell
eutraCelId adjacent cells in own Identity of 0...268435455, step 1
Administrative State of Administrative
administrativeState the cell, value is set by State of cell locked (0), unlocked (1)
The Cell Reselection Cell
celResTiFHM Timer (t-
t-ReselectionEUTRAN-SF-High Reselection 0.25 (0), 0.5 (1), 0.75 (2), 1 (3)
The Cell Reselection Cell
celResTiFMM Timer (t-
t-ReselectionEUTRAN-SF-Medium Reselection 0.25 (0), 0.5 (1), 0.75 (2), 1 (3)
The Cell Barred Flag Indicates if the
cellBarred cellBarredindicates if the cell cell is barred or barred (0), notBarred (1)
The Cell Reselection Defines the
cellReSelPrio Priority parameter
cellReselectionPriority absolute 0...7, step 1
Cell which are 'cell Indicates if the
cellReserve reserved for operator
cellReservedForOperatorUse cell is reserved Not Reserved (0), Reserved (1)
Scheduling Request Scheduling
cellSrPeriod Periodicity in a cell. Request 5ms (0), 10ms (1), 20ms (2), 40ms (3), 80ms (4)
O&M switch for Enables /
cqiAperEnable enabling / disabling disables
Corresponds to cqi- CQI aperiodc
cqiAperMode ReportingModeAperiodi reporting mode
cqi-ReportingModeAperiodic FBT1 (0), FBT2 (1)
Defines a timer in TTIs Sets the
cqiAperPollT for polling aperiodic aperiodic CQI 0...100 TTI, step 1 TTI
Parameter is vendor CQI format
cqiPerMode specific. indicator for WidebandCqiOnly (0), widebandAndSubbandCqi (1)
Defines periodicity of Periodic CQI /
cqiPerNp Np periodic CQI / PMI PMI feedback 10ms (0)
Number of periodic sub- Amount of
cqiPerSbCycK band reporting cycles periodic 1...4, step 1
O&M switch for Enables /
enabling / disabling
cqiPerSimulAck simultaneousAckNackAndCQI disables CQI
The parameter defines Cyclic prefix
cycPrefix cyclic prefix
cyclic prefix length in normal (0)
dFListPucch: dFListPucch:
dFListPucch SEQUENCE
deltaFList-PUCCH (see SEQUENCE
The parameter 'deltaF Used to define
dFpucchF1 PUCCH Format 1' is
deltaF-PUCCH-Format1 the PUCCH -2 (0), 0 (1), 2 (2)
The parameter 'deltaF Used to define
dFpucchF1b PUCCH Format 1b' is the PUCCH
deltaF-PUCCH-Format1b 1 (0), 3 (1), 5 (2)
 The parameter 'deltaF Used to define
dFpucchF2 PUCCH Format 2' is
deltaF-PUCCH-Format2 the PUCCH -2 (0), 0 (1), 1 (2), 2 (3)
The parameter 'deltaF Used to define
dFpucchF2a PUCCH Format 2a' is the PUCCH
deltaF-PUCCH-Format2a -2 (0), 0 (1), 2 (2)
The parameter 'deltaF Used to define
dFpucchF2b PUCCH Format 2b' is the PUCCH
deltaF-PUCCH-Format2b -2 (0), 0 (1), 2 (2)
Maximum number of Maximum
dSrTransMax allowed dedicated
DSR_TRANS_MAX number of 4n (0), 8n (1), 16n (2), 32n (3), 64n (4)
The Default Paging Cell specific
defPagCyc Cycle defines the cell paging DRX
defaultPagingCycle 32rf (0), 64rf (1), 128rf (2), 256rf (3)
Used for the calculation Used for the
deltaPreMsg3 of calculation of -1...6, step 1
Delta cyclic shift for Delta cyclic
deltaPucchShift PUCCH formats shift for 2...2, step 1
Enabling/disabling of Enabling/disabl
transport format
deltaTfEnabled DELTA_TF_ENABLED ing of transport
Enables/disables The Support of
dl64QamEnable downlink 64 QAM 64 QAM for
User can define lower Sets the power
dlCellPwrRed cell output power by reduction from 0...10 dB, step 0.1 dB
Downlink Channel Downlink
dlChBw Bandwidth defines DL Channel 5 MHz (2), 10 MHz (3), 20 MHz (4)
The used DL mimo Parameter to
dlMimoMode mode for each physical select the SingleTX (0), TXDiv (1), Static Open Loop MIMO (2), Dyna
O&M switch for Enables /
dlOlqcEnable enabling / disabling disables OLQC
Trigger Condition for Trigger
Power Headroom
dlPathlossChg DlPathlossChange Condition for 1 db (0), 3 db (1), 6 db (2), infinite (3)
Defines target block BLER target
dlTargetBler error ratio (BLER) for for downlink LA 0.0010...0.999, step 0.0010
Defines the default Default CQI
dlamcCqiDef Channel Quality value for DL 0...15, step 1
O&M switch for Enables /
dlamcEnable enabling / disabling disables DL
The parameter Set the
dlpcMimoComp determines power compensation 0...10 dB, step 0.01 dB
Determines if PRBs Determines if
dlsUsePartPrb partly allocated for PRBs partly not used (0), PRBs with PSS or SSS used (1), PRBs with P
The Access Barred for Indicates that
Emergency Calls Flag the access is
eCallAcBarred accessBarringForEmergencyCalls
E-UTRA Absolute E-UTRA
earfcnDL Radio Frequency Absolute Radio 0...65535, step 1
E-UTRA Absolute E-UTRA
earfcnUL Radio Frequency Absolute Radio 0...65535, step 1
Flag if better cell HO is Flag if better
enableBetterCellHo enabled cell HO is
Flag if coverage HO is Flag if
enableCovHo enabled coverage HO
The E-UTRAN Cell The E-UTRAN
eutraCelId Identifier is unique
eUTRANcellIdentifier Cell Identifier is 0...268435455, step 1
This parameter defines This parameter
filterCenterTx absolute Tx frequency defines 0...3000000 kHz, step 1 kHz
Filter coefficient for Filter
filterCoeff RSRP measurements coefficient for
filterCoefficient fc0 (0), fc1 (1), fc2 (2), fc3 (3), fc4 (4), fc5 (5), fc6 (6), fc7 (7
Further PLMN ids of Further PLMN
the
furtherPlmnIdL plmn-IdentityList Cell. Indicates ids of the Cell.
The Mobile Country Indicates the
mcc mcc Code parameter Mobile Country 0...999, step 1
The Mobile Network Indicates the
mnc mnc Code parameter Mobile 0...999, step 1
 The Mobile Network Indicates the
mncLength Code Length length of the 2...3, step 1
The GrpAssigPUSCH The
grpAssigPUSCH parameter defines GrpAssigPUS 0...29, step 1
Indicates the maximum Indicates the
harqMaxMsg3 number of HARQ maximum 1...8, step 1
Indicates the maximum Indicates the
harqMaxTrDl number of HARQ maximum 1...16, step 1
Indicates the maximum Indicates the
harqMaxTrUl maxHARQ-Txnumber of HARQ maximum 1...7, step 1
Number of PRBs that Hopping
hopBwPusch are used for PUSCH Bandwidth of 2...2, step 1
Parameter Parameter
hopModePusch HopModePUSCH HopModePUS interSubFrame (0)
HW state of the cell, HW state of
hwState value is set by the cell faulty (0), working (1)
Defines the time period Time period for
inactivityTimer for the indication of the the indication 10...65535 second, step 1 second
Duration for which the Duration for
indefSrsDur duration Sounding RS shall be which SRS is
Defines an initial Initial
iniMcsDl modulation and coding modulation and 0...28, step 1
Defines an initial Initial
iniMcsUl modulation and coding modulation and 0...20, step 1
Defines the initial Initial
iniPrbsUl amount of PRBs in maximum 1...100, step 1
Defines the Intra- Intra-
intrFrBCList Frequency Blacklisted
IntraFreqBlacklistedCellList Frequency
Indicates the number of Indicates the
rangeIntraPci range PCIs in the range number of n4 (0), n8 (1), n12 (2), n16 (3), n24 (4), n32 (5), n48 (6), n6
Indicates the lowest Indicates the
startIntraPci start PCI in the range lowest PCI in 0...503, step 1
Defines the Intra- Intra-
intrFrNCList Frequency
IntraFreqNeighbouringCellList Frequency
The Physical Cell Identifies the
physCellIdNcl Identifier is a unique
physicalCellIdentity cell in a 0...503, step 1
The parameter defines Defines a cell-
qOffsetCell a cell-specific offset (in
q-OffsetCell specific offset -24 dB (0), -22 dB (1), -20 dB (2), -18 dB (3), -16 dB (4), -1
Used to control cell Indicates if
intrFrqCelRes reselection on intra-
intraFrequencyReselection intra-frequency allowed (0), notAllowed (1)
The IE PresenceAnten
intraPresAntP PresenceAntennaPort1
presenceAntennaPort1 naPort1 is
Id of the local cell Local Cell
lcrId resource Resource ID 0...255, step 1
This is the instance Instance
lnCelId identifier of object identifier of 1...65535, step 1
Local state of the cell, Local state of
localState value is set by the cell. blocked (0), unblocked (1)
Maximum Bit Rate that Maximum
maxBitrateDl shall not be exceeded bitrate in 50...300000 kbps, step 50 kbps
Maximum Bit Rate that Maximum
maxBitrateUl shall not be exceeded bitrate in uplink 50...75000 kbps, step 50 kbps
The parameter defines Maximum code
maxCrPgDl the maximum coderate rate for Paging 0.05...0.5, step 0.01
The parameter defines Maximum code
maxCrRa4Dl the maximum coderate rate for 0.05...0.5, step 0.01
The parameter defines Maximum code
maxCrRaDl the maximum coderate rate for 0.05...0.5, step 0.01
The parameter defines Maximum code
maxCrSibDl the maximum coderate rate for System 0.05...0.5, step 0.01
 The Number of
maxNrSymPdcch MaximumNumberOfOF OFDM 1...3, step 1
Maximum number of Maximum
maxNumAUeHo UEs in the cell with number of 1...150, step 1
Maximum number of Maximum
maxNumActUE UEs in the cell with number of 1...100, step 1
Maximum number of Maximum
maxNumRrc UEs in the cell with number of 1...200, step 1
Maximum number of Maximum
maxNumUeDl simultaneous users number of 1...10, step 1
Maximum number of Maximum
maxNumUeUl simultaneous users number of 1...4, step 1
Selects whether the Selects the
mbrSelector UECapability or O and source of the ueCapability (0), OaM (1)
The MBSFN Neighbour Parameter is
Cell Configuration
mbsfnNbCellConfmbsfn-NeighbourCellConfig FFS. 0...3, step 1
CQI Threshold for CQI Threshold
mimoOlCqiThD fallback to open loop for fallback to 0...16, step 0.1
CQI Threshold for CQI Threshold
mimoOlCqiThU activation of open loop for activation of 0...16, step 0.1
Rank Threshold for Rank
mimoOlRiThD fallback to open loop Threshold for 1...2, step 0.05
Rank Threshold for Rank
mimoOlRiThU activation of open loop Threshold for 1...2, step 0.05
Minimum Bit Rate to be Minimum
minBitrateDl granted by the DL bitrate in 5...500 kbps, step 5 kbps
Minimum Bit Rate to be Minimum
minBitrateUl granted by the UL bitrate in uplink 5...500 kbps, step 5 kbps
The parameter Defines the
Modification Period
modPeriodCoeff modificationPeriodCoeff length of the 2 (0), 4 (1), 8 (2), 16 (3)
AckNack index offset Offset used to
n1PucchAn relative to the lowest calculate 11...36, step 25
Maximum number of Constant for
n310 n310 consecutive "out of 'out of sync' n1 (0), n2 (1), n3 (2), n4 (3), n6 (4), n8 (5), n10 (6), n20 (7)
Maximum number of Constant for 'in-
n311 n311 consecutive "in-sync" sync' n1 (0), n2 (1), n3 (2), n4 (3), n5 (4), n6 (5), n8 (6), n10 (7)
Parameter "Number Defines the
nCellChgHigh CellChanges High
n-CellChangeHigh number of cell 1...16, step 1
Parameter "Number Defines the
nCellChgMed CellChanges Medium
n-CellChangeMedium number of cell 1...16, step 1
Number of physical Number of
nCqiRb resource blocks that physical 1...2, step 1
The shift Delta Offset is Is the offset to
given by the parameter
npdschEpreOff nomPDSCH-RS-EPRE-Offset the ration of -2 dB (0), 0 dB (1), 2 dB (2), 4 dB (3), 6 dB (4), 8 dB (5), 10
The Number of The Number of
numOfTxPorts Transmission Antenna Transmission 1 (0), 2 (1)
Access Class Barring Access Class
ocAcBarAC List (5 Bit) for
ac-BarringForSpecialAC Barring List (5 Bit 0: AC 11, Bit 1: AC 12, Bit 2: AC 13, Bit 3: AC 14, Bit 4:
The Access Class Defines the
ocAcBarTime Barring Time defines
accessClassBarringTime Access Class 4s (0), 8s (1), 16s (2), 32s (3), 64s (4), 128s (5), 256s (6), 5
The Access Probability Defines a
ocAcProbFac Factor defines a
ac-BarringFactor probability for a 0% (0), 5% (1), 10% (2), 15% (3), 20% (4), 25% (5), 30% (6
Operational State of Operational
operationalState the cell, value is set by State of cell disabled (0), enabled (1)
UE specific nominal Controls mean
p0NomPucch power to be used for
P0_NOMINAL_PUCCH received SNR -127...-96 dB, step 1 dB
UE specific nominal UE specific
p0NomPusch power for the PUSCH.
P0_NOMINAL_PUSCH(j=1) PUSCH mean -126...24 dB, step 1 dB
UE specific power UE specific
p0UePucch offset to be used for
P0_UE_PUCCH parameter, -8...7 dB, step 1 dB
 UE specific power UE specific
p0UePusch offset to be used for PUSCH power -8...7 dB, step 1 dB
This parameter defines This parameter
pMax Pmax the maximum output defines the 0...50 dBm, step 0.1 dBm
Paging nB defines the The number of
pagingNb nB number of possible possible oneT (2), halfT (3), quarterT (4), oneEighthT (5), oneSixtee
PDCCH Aggregation PDCCH
pdcchAggPaging for Paging. Defines Aggregation for 4...8, step 4
The parameter defines Aggregation
pdcchAggPreamb aggregation level by level of 4...8, step 4
PDCCH Aggregation PDCCH
pdcchAggRaresp for Random Access Aggregation for 4...8, step 4
PDCCH Aggregation PDCCH
pdcchAggSib for Secondary System Aggregation for 4...8, step 4
The configured PHICH Indicates the
phichDur duration puts a lower duration of Normal (0), Extended (1)
The Physical Hybrid Indicates the
phichRes ARQ Indicatior Channel PHICH N = 1/6 (0), N = 1/2 (1), N = 1 (2), N = 2 (3)
Physical Layer Cell Physical layer
phyCellId Identity defines cell identity 0...503, step 1
Preamble cyclic shift Defines the
prachCS defines the PRACH Cyclic 0...15, step 1
Defines allowed Defines
System frame and sub-
prachConfIndex prach-ConfigurationIndex subframes and 3...24, step 1
First physical resource Defines the
prachFreqOff block available for
prach-FrequencyOffset location in 0...94, step 1
High speed flag for High speed
prachHsFlag PRACH preamble flag for PRACH
The Power Ramping Defines the
Step Size parameter
prachPwrRamp powerRampingStep power 0dB (0), 2dB (1), 4dB (2), 6dB (3)
The parameter Defines the
Preamble
preambTxMax preambleTransMax maximum 3 (0), 4 (1), 5 (2), 6 (3), 7 (4), 8 (5), 10 (6), 20 (7), 50 (8), 10
Number of cyclic shift PUCCH Cyclic
pucchNAnCs for PUCCH formats Shift for Mixed 0...0, step 1
The parameter defines Delta offset
puschAckOffI the delta offset index
deltaOffset-ACK-Index index for 0...10, step 1
The parameter defines Delta offset
puschCqiOffI the delta offset index
deltaOffset-CQI-Index index for CQI 0...15, step 1
The Pusch Hopping PUSCH
Offset parameter
puschHopOffset pusch-hoppingOffset Hopping Offset 0...98 PRB, step 1 PRB
The parameter defines Delta offset
puschRiOffI the delta offset index
deltaOffset-RI-Index index for RI 0...12, step 1
The Qhyst parameter Provides the
qHyst q-Hyst provides the hysteresis hysteresis 0dB (0), 1dB (1), 2dB (2), 3dB (3), 4dB (4), 5dB (5), 6dB (6
Parameter defines an Hysteresis
qHystSfHigh sf-High additional hysteresis value in High -6 dB (0), -4 dB (1), -2 dB (2), 0 dB (3)
Parameter defines an Hysteresis
qHystSfMed sf-Mediumadditional hysteresis value in -6 dB (0), -4 dB (1), -2 dB (2), 0 dB (3)
Specifies the minimum Indicates the
qrxlevmin q-RxLevMinrequired Rx RSRP minimum -140...-44 dBm, step 2 dBm
Specifies the minimum Indicates the
qrxlevminintraF q-RxLevMinrequired Rx RSRP minimum -140...-44 dBm, step 2 dBm
The Random Access Defines the
raBackoff FFS Backoff parameter backoff that 2 (0), 5 (1), 10 (2), 20 (3), 50 (4), 100 (5), 200 (6), 500 (7),
The Maximum Content The Maximum
raContResoT ContentionResolution
ResolutionTimer
Timer Content 8ms (0), 16ms (1), 24ms (2), 32ms (3), 40ms (4), 48ms (5)
After being informed C-RNTI reuse
raCrntiReuseT that a UE has gone to timer 1...60 s, step 1 s
Path loss threshold in Path loss
dB required for
raMsgPoffGrB messagePowerOffsetGroupB threshold in dB -infinity (0), 0 dB (1), 5 dB (2), 8 dB (3), 10 dB (4), 12 dB (5
 This parameter is used Defines the
raNondedPreamb to determine the total total number of 4 (0), 8 (1), 12 (2), 16 (3), 20 (4), 24 (5), 28 (6), 32 (7), 36 (
Power Ramping Setup - Power
WA in Setup
raPowRampSetuppower Ramping 3GPP Ramping 0...1, step 1
Defines the size of the Defines the
raPreGrASize Random Access
sizeOfRA-PreambleGroupA size of the 4 (0), 8 (1), 12 (2), 16 (3), 20 (4), 24 (5), 28 (6), 32 (7), 36 (
Random Access Random
raRespWinSize Response Window Access 2 (0), 3 (1), 4 (2), 5 (3), 6 (4), 7 (5), 8 (6), 10 (7)
Defines the data Data volume
raSmallVolUl volume to be used for assigned for 56 bits (0), 144 bits (1), 208 bits (2), 256 bits (3)
Defines if RI reporting Defines if RI
riEnable is enabled (true) or not reporting is
The parameter defines Multiplier M for
riPerM the offset for periodic defining 1 (0), 2 (1)
The parameter defines Time offset for
riPerOffset the offset for periodic periodic -1...0 ms, step 1 ms
Preable generation is RACH Root
rootSeqIndex started from the Root Sequence 0...837, step 1
Rx Antenna Specific Rx Antenna
rxPowerScaling Power Scaling Factor Specific Power 0...200 dBm, step 0.01 dBm
The Sintrasearch Defines the
sIntrasearch parameter defines the threshold (in
s-IntraSearch 0...62 dB, step 2 dB
The sNonintrsearch Defines the
parameter defines the threshold (in
sNonIntrsearch s-NonIntraSearch 0...62 dB, step 2 dB
The parameter System Indicates which
si2MappingInfo Information 2 Mapping System SIB2 (0), SIB3 (1), SIB4 (2)
The parameter System Indicates the
si2Periodicity Information 2 repetition 80 (0), 160 (1), 320 (2), 640 (3), 1280 (4), 2560 (5), 5120 (6
The parameter System Indicates the
si2Repetition Information 2 repetition of 1...4, step 1
The parameter System Indicates which
si3MappingInfo Information 2 Mapping System SIB2 (0), SIB3 (1), SIB4 (2)
The parameter System Indicates the
si3Periodicity Information 2 repetition 80 (0), 160 (1), 320 (2), 640 (3), 1280 (4), 2560 (5), 5120 (6
The parameter System Indicates the
si3Repetition Information 3 repetition of 1...4, step 1
The parameter System Indicates which
si4MappingInfo Information 2 Mapping System SIB2 (0), SIB3 (1), SIB4 (2)
The parameter System Indicates the
si4Periodicity Information 2 repetition 80 (0), 160 (1), 320 (2), 640 (3), 1280 (4), 2560 (5), 5120 (6
The parameter System Indicates the
si4Repetition Information 4 repetition of 1...4, step 1
The parameter SI Defines the
siWindowLen Window Length defines common
si-WindowLength 1ms (0), 2ms (1), 5ms (2), 10ms (3), 15ms (4), 20ms (5), 4
Access Class Barring Access Class
sigAcBarAC List (5 Bit) for
ac-BarringForSpecialAC Barring List (5 Bit 0: AC 11, Bit 1: AC 12, Bit 2: AC 13, Bit 3: AC 14, Bit 4:
The Access Class Defines the
sigAcBarTime Barring Time defines
accessClassBarringTime Access Class 4s (0), 8s (1), 16s (2), 32s (3), 64s (4), 128s (5), 256s (6), 5
The Access Probability Defines a
sigAcProbFac Factor defines a
ac-BarringFactor probability for a 0% (0), 5% (1), 10% (2), 15% (3), 20% (4), 25% (5), 30% (6
Enable/disable Uplink Enable/disable
soundRsEnabled Sounding Reference Uplink
Downlink scheduling Downlink
srbSchedWeightDl wieght for signalling scheduling 1...1000, step 1
Uplink scheduling Uplink
srbSchedWeightUl wieght for signalling scheduling 1...100, step 1
Selects one of the four SRS
srsBandwidth possible layers for
srsBandwidth Bandwidth 0bw (0), 1bw (1), 2bw (2), 3bw (3)
Defines the allowed SRS
srsBwConf BW for SRS in the
srsBandwidthConfiguration Bandwidth 0bw (0), 1bw (1), 2bw (2), 3bw (3), 4bw (4), 5bw (5), 6bw (6
 Defines if in the cell it is Defines SRS
srsHoppingBw allowed to have SRS
srsHoppingBandwidth hopping 0hbw (0), 1hbw (1), 2hbw (2), 3hbw (3)
UE specific power Defines the
srsPwrOffset offset to be used for
P_SRS_OFFSET power offset 0...15, step 1
Defines if SRS and Defines if SRS
ACK/NACK are allowed can be
srsSimAckNack ackNackSrsSimultaneousTransmission Disabled (0), Enabled (1)
Determines the Periodicy of
srsSubfrConf periodicy of SRS in
srsSubframeConfiguration SRS 0sc (0), 1sc (1), 2sc (2), 3sc (3), 4sc (4), 5sc (5), 6sc (6), 7
The SU2 Repetition Indicates the
su2Repetition Period indicates the repetition 40 (0), 80 (1), 160 (2), 320 (3), 640 (4), 1280 (5), 2560 (6),
SW state of the cell, SW state of
swState value is set by the cell. detected (0), configured (1)
The parameter Defines
syncSigTxMode Synchronization whether SingleTx (0), TxDiv (1)
The Timer T300 T300
t300 t300 supervises the RRC supervises the 100ms (0), 200ms (1), 300ms (2), 400ms (3), 600ms (4), 1
The Timer T301 T301
t301 t301 supervises the RRC supervises the 100ms (0), 200ms (1), 300ms (2), 400ms (3), 600ms (4), 1
eNB sends this T302
t302 t302 parameter to UE in the suppresses 1000...16000 ms, step 1000 ms
The Timer T304 The Timer
t304IntraLte t304 supervises the T304 50ms (0), 100ms (1), 150ms (2), 200ms (3), 500ms (4), 10
The Timer T310 T310
t310 t310 supervises the supervises the 0ms (0), 50ms (1), 100ms (2), 200ms (3), 500ms (4), 1000
The Timer T311 T311
t311 t311 supervises the RRC supervises the 1000ms (0), 3000ms (1), 5000ms (2), 10000ms (3), 15000m
Timer TCRmax defines Defines the
tEvalulation the duration for
t-Evalulation duration for 30s (0), 60s (1), 120s (2), 180s (3), 240s (4)
The Timer Defines the
tHystNormal TCRmaxHyst defines additional
t-HystNormal 30s (0), 60s (1), 120s (2), 180s (3), 240s (4)
Time period of the Time period of
tPeriodicBsr periodic Buffer Status the periodic
PeriodicBsrTime 5ms (0), 10ms (1), 16ms (2), 20ms (3), 32ms (4), 40ms (5)
UE configuration for UE
tPeriodicPhr sending periodic
PeriodicPPHRtimer configuration 10sf (0), 20sf (1), 50sf (2), 100sf (3), 200sf (4), 500sf (5), 1
Minimum Intermediate Minimum
tProhibitPhr Time between two
ProhibitedPHRTimer Intermediate 0sf (0), 10sf (1), 20sf (2), 50sf (3), 100sf (4), 200sf (5), 500
Time the Regular Time the
tReTxBsrTime BSRs is repeated when Regular BSRs 320 ms (0), 640 ms (1), 1280 ms (2), 2560 ms (3), 5120 m
The Treselection Defines the cell
tReselEutr parameter defines the reselection
t-ReselectionEUTRAN 0...7 s, step 1 s
Determines the Determines the
taMaxOffset maximum allowed time maximum 1...9 16Ts, step 1 16Ts
Determines the number Determines the
taTimer of subframes after
timeAlignmentTimer number of 500 ms (0), 750 ms (1), 1280 ms (2), 1920 ms (3), 2560 m
The Tracking Area Identifies the
tac Code is a code that
trackingAreaCode Tracking Area 0...65535, step 1
Specifies the threshold Specifies the
threshSrvLow for serving frequency low threshold
threshServingLow 0...62 dB, step 2 dB
Selects between TPC Selects step-
tpcStepSize TPC step step-size
size sets {-1; 0; 1; size set. It is TPC step size set -1,0,3 (0), TPC step size set -1,1 (1)
Defines mapping of the Defines
txPowerScaling RP3 I and Q values mapping of the 1...10000, step 1
Uplink Channel Uplink Channel
ulChBw Bandwidth defines UL Bandwidth 5 MHz (2), 10 MHz (3), 20 MHz (4)
Enables uplink group Enables uplink
ulGrpHop hopping in PUSCH and group hopping.
The parameter defines The parameter
ulRsCs cyclic shift of uplink defines cyclic 0...7, step 1
Defines if sequence Defines if
ulSeqHop hopping is enabled or sequence
sequenceHoppingEnabled
 PUSCH channel PUSCH
ulSeqSft sequence shift which is channel 0...29, step 1
Defines target Block Target BLER
ulTargetBler Error Ratio for uplink for AMC UL 0...50 %, step 1 %
O&M switch for Switch the
ulamcAllTbEn enabling / disabling the counting of all
O&M switch for Switch UL
ulamcEdgFugEn enabling / disabling 1st OLLA
O&M switch for Enables /
ulamcEnable enabling / disabling the disables UL
The parameter defines UL AMC inner
ulamcSwitchPer the period in sent loop MCS 10...500 tb, step 10 tb
O&M switch for Switch the UL
ulatbEnable enabling / disabling the ATB on/off
The parameter defines UL ATB
ulatbEventPer the period in MCS execution 1...50, step 1
Enables/disables the Enables/disabl
accumulation of
ulpcAccuEnable ACCUMULATION_ENABLED es the
UE specific fractional Used as a
ulpcAlpha alpha path loss fractional path alpha 0 (0), alpha 0.4 (1), alpha 0.5 (2), alpha 0.6 (3), alpha
The Preamble Initial Defines the
ulpcIniPrePwr Received Target Power initial power for
preambleInitialReceivedTargetPower -120 dBm (0), -118 dBm (1), -116 dBm (2), -114 dBm (3), -
TPC command TPC command
ulpcRarespTpc deltaMsg2indicated in the random indicated in the -6...8 dB, step 2 dB
 Default Value Formula

- internal_value = gui_value * 10

3 internal_value = gui_value * 10

1 internal_value = gui_value * 10

10 TTI internal_value = gui_value

50 TTI internal_value = gui_value

16 (6)

1 internal_value = gui_value

true

560 bits internal_value = gui_value

1500 ms internal_value = gui_value

- internal_value = gui_value

unblocked (1)

4 PRBs internal_value = gui_value

10 number internal_value = gui_value

10 internal_value = gui_value

10 internal_value = gui_value

10 internal_value = gui_value

- internal_value = gui_value

0.5 internal_value = gui_value * 20

3 internal_value = gui_value * 10

0.5 internal_value = gui_value * 20

- internal_value = gui_value

- internal_value = gui_value

1 internal_value = gui_value

750 (5)
1000 internal_value = gui_value

100 internal_value = gui_value

50 internal_value = gui_value

10 internal_value = gui_value

10 internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

5 internal_value = gui_value

512 bit internal_value = gui_value

5 internal_value = gui_value

64 (4)

1 internal_value = gui_value

120 (23)

50 (10)

50 (10)

3 internal_value = gui_value

20 internal_value = gui_value

500 ms internal_value = gui_value

500 ms internal_value = gui_value / 100

10 s internal_value = gui_value * 10

5s internal_value = gui_value * 10

50 ms internal_value = gui_value

100 ms internal_value = gui_value

10000 ms internal_value = gui_value

2000 ms internal_value = gui_value

20 ms internal_value = gui_value

800 ms internal_value = gui_value

100 ms internal_value = gui_value

70 ms internal_value = gui_value

50 ms internal_value = gui_value

50 ms internal_value = gui_value

1 internal_value = gui_value

2 internal_value = gui_value * 10

150 ms internal_value = gui_value

0.2 internal_value = gui_value * 20

- internal_value = gui_value * 10

5 internal_value = gui_value * 10

- internal_value = gui_value * 10

1000 ms internal_value = gui_value

100 ms internal_value = gui_value

1.2 internal_value = gui_value * 20

0.9 internal_value = gui_value * 20

50 TTI internal_value = gui_value

10 s internal_value = gui_value * 10

5s internal_value = gui_value * 10

- internal_value = gui_value

infinity (7)

1024ms (4)
-

infinity (7)

1024ms (4)

- internal_value = gui_value

- internal_value = gui_value

false

1 internal_value = gui_value

- internal_value = gui_value

notBarred (1)

- internal_value = gui_value

true

FBT2 (1)

3 TTI internal_value = gui_value

1 internal_value = gui_value

true

0 (1)

-
0 (1)

0 (1)

0 (1)

64n (4)

128rf (2)

- internal_value = gui_value

2 internal_value = gui_value

false

- internal_value = gui_value * 10

10 MHz (3)

TXDiv (1)

true

3 db (1)

0.1 internal_value = gui_value * 1000

2 internal_value = gui_value

true

- internal_value = gui_value * 100

PRBs with PSS or SSS and PBCH used (2)

false

5000 internal_value = gui_value

23000 internal_value = gui_value

true

true

- internal_value = gui_value

- internal_value = gui_value

fc4 (4)

- internal_value = gui_value

- internal_value = gui_value
- internal_value = gui_value

- internal_value = gui_value

5 internal_value = gui_value

3 internal_value = gui_value

5 internal_value = gui_value

2 internal_value = gui_value

300 second internal_value = gui_value

true

4 internal_value = gui_value

- internal_value = gui_value

10 internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

0 dB (15)

1 internal_value = gui_value

- internal_value = gui_value

unblocked (1)

170000 kbps internal_value = gui_value

50000 kbps internal_value = gui_value

0.12 internal_value = gui_value * 100

0.12 internal_value = gui_value * 100

0.12 internal_value = gui_value * 100

0.12 internal_value = gui_value * 100

3 internal_value = gui_value

60 internal_value = gui_value

50 internal_value = gui_value

100 internal_value = gui_value

4 internal_value = gui_value

4 internal_value = gui_value

- internal_value = gui_value

9 internal_value = gui_value * 10

11 internal_value = gui_value * 10

1.4 internal_value = gui_value * 20

1.6 internal_value = gui_value * 20

30 kbps internal_value = gui_value

30 kbps internal_value = gui_value

36 internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

2 internal_value = gui_value

0 dB (1)

2 (1)

- internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value
- internal_value = gui_value

43 dBm internal_value = gui_value * 10

quarterT (4)

4 internal_value = gui_value

4 internal_value = gui_value

4 internal_value = gui_value

4 internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

3 internal_value = gui_value

1 internal_value = gui_value

false

2dB (1)

8 (5)

- internal_value = gui_value

10 internal_value = gui_value

8 internal_value = gui_value

6 PRB internal_value = gui_value

12 internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

32ms (3)

20 s internal_value = gui_value

10 dB (4)
40 (9)

- internal_value = gui_value

32 (7)

10 (7)

144 bits (1)

false

- internal_value = gui_value

- internal_value = gui_value

117.22 dBm internal_value = gui_value * 100

- internal_value = gui_value

- internal_value = gui_value

1 internal_value = gui_value

SIB3 (1)

1 internal_value = gui_value

SIB4 (2)

1 internal_value = gui_value

10ms (3)

false

10 internal_value = gui_value

10 internal_value = gui_value

3bw (3)

-
3hbw (3)

7 internal_value = gui_value

Enabled (1)

8000 ms internal_value = gui_value

200ms (3)

40ms (5)

20sf (1)

2560 ms (3)

- internal_value = gui_value

2 16Ts internal_value = gui_value

- internal_value = gui_value

- internal_value = gui_value

4024 internal_value = gui_value

10 MHz (3)

false

- internal_value = gui_value

false
- internal_value = gui_value

10 % internal_value = gui_value

true

true

true

30 tb internal_value = gui_value

true

1 internal_value = gui_value

true

alpha 1 (7)

-104 dBm (8)

- internal_value = (gui_value + 6) / 2