Scribd
Upload
2K views4 pages

Technical Service Bulletin: - Description

This document provides procedures for resetting adaptive values and relearning in automatic transmissions for various Kia models. It involves using the GDS or Hi-Scan tool to reset adaptive values in the transmission section menu, then performing a dynamic relearn by driving the vehicle through gears at a specific throttle position and temperature. A static relearn is also outlined to shift between neutral and drive/reverse repeatedly until shifts are smooth. Resetting and relearning must be done after repairs like transmission replacement or control module replacement/reprogramming.

Uploaded by

08088338
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views4 pages

Technical Service Bulletin: - Description

This document provides procedures for resetting adaptive values and relearning in automatic transmissions for various Kia models. It involves using the GDS or Hi-Scan tool to reset adaptive values in the transmission section menu, then performing a dynamic relearn by driving the vehicle through gears at a specific throttle position and temperature. A static relearn is also outlined to shift between neutral and drive/reverse repeatedly until shifts are smooth. Resetting and relearning must be done after repairs like transmission replacement or control module replacement/reprogramming.

Uploaded by

08088338
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
  • Technical Service Bulletin Overview
  • Service Procedure

Model All Model

Technical
Service Group Automatic Transaxle(52)

Bulletin Number KT2007020701

Subject Date Wednesday, February 07, 2007


Automatic Transmission Adaptive Value Reset /
Relearn (Trans/Driveline - 018) Area N. America

- Description
This bulletin provides automatic transmission adaptive value data reset (erase) and relearn procedures.

The PCM and TCM contain logic to adjust the solenoid duty and line pressure to compensate for normal clutch
wear over the life of the transmission. Adaptive value reset and relearn must be performed to provide optimum
shift quality after completing the following repairs.

z Replace automatic transmission


z Replace PCM or TCM .
z Reprogram PCM or TCM

Adaptive values must be reset using procedure 1 or 2 according to model and model year (MY) as shown below.
The adaptive values must also be relearned by following steps 2 and 3 after resetting.

Kia Vehicles Requiring Automatic Transmission Adaptive Value Reset / Relearn

Procedure 1 Procedure 2

Disconnect Negative
Model Battery Cable for 10 Use Hi Scan or GDS
Seconds

Amanti 2004 MY 2005 and later MY

Optima 2001 - 2004 MY 2005 and later MY

Rio ---------------------- 2006 and later MY

Sedona 2002 - 2004 MY 2005 and later MY

Spectra ---------------------- 2004.5 and later MY

Sportage ---------------------- 2005 and later MY

Sorento ---------------------- 2005 and later MY

- Effective Vehicle Information

All models supported by the table displayed above.


- Service Procedure

Perform the Automatic Transmission Adaptive Value Reset Procedure as follows:

Use the GDS or Hi-Scan Procedure to reset the automatic transmission adaptive values found in the automatic
transmission section menu. Follow the steps shown in RESETTING AUTO T/A VALUES or INIT OF TCU
LEARNING (Sorento - TCU SUB ROM RESET) menu sections

GDS Procedure:

1. Hook GDS to vehicle and input VIN or auto


select VIN

2. Select Automatic Transmission system

3. Select Vehicle S/W Management tab as shown

4. Select “Init Of TCU Learning” as shown

1. Follow instructions at right:

z Ignition key on
z Engine off
z Shift lever in P or N
z Vehicle speed 0 MPH

2. Click the “OK” button.

1. Adaptive Reset is complete as shown

2. Turn the ignition key off for ten seconds


Hi-Scan Procedure:

Turn ignition key to “ON” position (do not start) and


move the shift lever to “P”.

1. Attach Hi-Scan Data Link Connector (DLC)

z Select vehicle
z Select “AUTOMATIC TRANSAXLE” Menu.
z Select “RESETTING AUTO T/A VALUES”

2. Resetting Auto T/A Values

z Press “REST” button


z Press “YES” button
z You must see the “COMPLETED” Message

3. Turn off Scan tool and turn ignition key off for 10
Seconds.

2. Driving Relearn

Dynamic Automatic Transmission Adaptive Learning Procedure:

1. Attach Hi-Scan or GDS and monitor ATF temperature and TPS percent.

2. Bring ATF temp. to just over 120 F and drive from a stop shifting from 1st to 3rd gears (Five speeds – 1st to 4th
gears) at 30% TPS (Approx. 3000 RPM shift). Repeat 3 – 5 times until any shock or flare is eliminated.
3. Static Shift Relearn

1. Stop the vehicle and shift into N for three seconds. Shift from N to D for two seconds. Repeat 3 – 5 times until
there is no N to D shock.

2. Stop the vehicle and shift into N for three seconds. Shift from N to R for two seconds. Repeat 3 – 5 times until
there is no N to R shock.

Technical Service Bulletin Model All Model Group Automatic Transaxle(52) Number KT2007020701 Subject Automatic Transmissi
- Service Procedure Perform the Automatic Transmission Adaptive Value Reset Procedure as follows: Use the GDS or Hi-Scan
2. Driving Relearn Dynamic Automatic Transmission Adaptive Learning Procedure: 1. Attach Hi-Scan or GDS and monitor ATF
3. Static Shift Relearn 1. Stop the vehicle and shift into N for three seconds. Shift from N to D for two seconds. Repeat

You might also like