Scribd
Upload
85 views2 pages

Isolated Foundation Calculation (ACI) : Checking

This document provides the design calculations for an isolated foundation supporting vertical and lateral loads. It includes the input load data, calculation of ultimate loads, checking for contact pressure, overturning, sliding stability, shear capacity, and punching shear. The results show the required base dimensions of 2000mm x 2800mm with depths of 305mm and 375mm. It also specifies the required reinforcing steel areas and spacing in the x and z directions.

Uploaded by

Sher Afgan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views2 pages

Isolated Foundation Calculation (ACI) : Checking

This document provides the design calculations for an isolated foundation supporting vertical and lateral loads. It includes the input load data, calculation of ultimate loads, checking for contact pressure, overturning, sliding stability, shear capacity, and punching shear. The results show the required base dimensions of 2000mm x 2800mm with depths of 305mm and 375mm. It also specifies the required reinforcing steel areas and spacing in the x and z directions.

Uploaded by

Sher Afgan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Issue: Design Page

Isolated Foundation Calculation (ACI) Date: 0


1 of 2
Revised by: Test1
Project: 0
Checked by: Test2

Input Data
Loads (kN) Mz Concrete Strength Foundation Properties
Px Py (kN.m) f'c (N/mm2) = 21 H (mm) 2250 h (mm) 0
Dead 0 9.7 0 Steel Strength hw (mm) 0 L/B 1.4
Live 0 19.7 0 fy (N/mm2) = 420 Pedestal Dimension
Wind 32 35 0 Allowable Soil Pressure x (mm) 700 y (mm) 300
E 8.8 16.8 0 qa (kN/m2) = 76.68
Sum 40.8 81.2 0 Base Soil angle of internal friction 20

Ultimate Loads (ACI 9.2.)


Load Case 0.9D+1.3W 1.4D+1.7L 0.75(1.4D+1.7L+1.7W) 0.75(1.4D+1.7L+1.87E)
Factors 0.9 1.3 1.4 1.7 1.05 1.275 1.275 1.05 1.275 1.4025
Pux (kN) = 41.6 0 40.8 12.342
Puy (kN) = 54.23 47.07 79.9275 58.8645
Muz (kN.m) = 0 0 0 0

CHECKING:

Contact Pressure qmax = 96.85 kN/m2 qmin = 26.6 kN/m2


qGP (gross pressure) (kN/m2) = ( 3qmax + qmin ) /4
qGP = 79.29 kN/m2 > qa = 76.68 NO

Stability against Overturning moment 91.8 kN.m


Overturning Stabilizing moment 483.936 kN.m
Stabilizing moment
= 5.272 > 1.5 YES
Overturning moment

Stability against Fv ´ tan q


Sliding = 3.084 > 1.5 YES
Fh

Check Wide Beam Vc (kN) max Vu (kN) Load Case


Shear 465.895 59.680 3
max Vu / 0.85Vc = 0.151 < 1.00 YES

Check Punching Vc (kN) max Vu (kN) Load Case


Shear 1393.027 71.249 3
max Vu / 0.85Vc = 0.06 < 1.00 YES

Results:

Base Dimensions
B= 2000 mm d= 305 mm
L= 2800 mm D= 375 mm

Reinforcment
x - Direction z - Direction
Bottom Reinforcement Top Reinforcement Bottom Reinforcement
As (cm2) = 10.98 10.98 15.372
r= 0.0018 0.0018 0.0018
Issue: Design Page
Isolated Foundation Calculation (ACI) Date: 0
2 of 2
Revised by: Test1
Project: 0
Checked by: Test2

Fy = 81.2 kN

Fx = 40.8 kN Mz = 0 kN.m
hw = 0

GWT

H= As (cm2) = 10.98 (in both directions)


2250 hw = 0

D = 375 d = 305 mm

L = 2800 mm

As (cm2) = 15.37 (z - direction) As (cm2) = 10.98 (x - direction)

z
B = 2000
y = 300
x

x = 700

* Dimensions are in mm

You might also like