Operating Manual

Translation of the original operating manual

VD (E2.1)
Vacuum Drying Oven
with microprocessor program controller RD3

Model Model version Art. No.

VD 23 VD023-230V 9030-0029, 9130-0029
VD 23-UL VD023UL-120V 9030-0035, 9130-0035
VD 53 VD053-230V 9030-0030, 9130-0030
VD 53-UL VD053UL-120V 9030-0036, 9130-0036
VD 115 VD115-230V 9030-0031, 9130-0031
VD 115-UL VD115UL-120V 9030-0037, 9130-0037

BINDER GmbH
 Address: Post office box 102, 78502 Tuttlingen, Germany  Phone: +49 7462 2005 0
 Fax: +49 7462 2005 100  Internet: http://www.binder-world.com
 E-mail: [email protected]  Service Hotline: +49 7462 2005 555
 Service Fax: +49 7462 2005 93 555  Service E-Mail: [email protected]
 Service Hotline USA: +1 866 885 9794 or +1 631 224 4340 x3
 Service Hotline Asia Pacific: +852 390 705 04 or +852 390 705 03
 Service Hotline Russia and CIS: +7 495 988 15 16

Issue 09/2018 Art. No. 7001-0125

Contents
1. SAFETY .................................................................................................................. 5
1.1 Legal considerations ........................................................................................................................... 5
1.2 Structure of the safety instructions ...................................................................................................... 5
1.2.1 Signal word panel...................................................................................................................... 5
1.2.2 Safety alert symbol.................................................................................................................... 6
1.2.3 Pictograms ................................................................................................................................ 6
1.2.4 Word message panel structure ................................................................................................. 7
1.3 Localization / position of safety labels on the chamber ....................................................................... 7
1.4 Type plate ............................................................................................................................................ 8
1.5 General safety instructions on installing and operating the chamber .................................................. 9
1.6 Intended use...................................................................................................................................... 11
1.7 Operating instructions ....................................................................................................................... 11
1.8 Measures to prevent accidents ......................................................................................................... 12
2. DESCRIPTION OF THE EQUIPMENT ................................................................. 13
2.1 Chamber overview ............................................................................................................................ 14
2.2 VD 23 control panel ........................................................................................................................... 15
2.3 VD 53 / 115 control panel .................................................................................................................. 15
2.4 Connections at the rear of the chamber ............................................................................................ 16
3. COMPLETENESS OF DELIVERY, TRANSPORTATION, STORAGE, AND
INSTALLATION .................................................................................................... 17
3.1 Unpacking, and checking equipment and completeness of delivery................................................. 17
3.2 Guidelines for safe lifting and transportation ..................................................................................... 18
3.3 Storage .............................................................................................................................................. 18
3.4 Location of installation and ambient conditions ................................................................................. 18
4. INSTALLATION AND CONNECTIONS ................................................................ 20
4.1 Vacuum expansion racks .................................................................................................................. 20
4.2 Vacuum connection ........................................................................................................................... 20
4.3 Inert gas connection .......................................................................................................................... 20
4.4 Electrical connection ......................................................................................................................... 21
5. START UP ............................................................................................................ 22
5.1 Settings at the RD3 program controller ............................................................................................. 22
5.2 General indications on the RD3 program controller .......................................................................... 23
6. FIXED VALUE ENTRY MODE ............................................................................. 25

7. WEEK PROGRAM EDITOR ................................................................................. 26

7.1 Program table template for Week program Editor ............................................................................ 28
7.2 Programming example of the Week program editor ......................................................................... 29
7.2.1 Desired time function .............................................................................................................. 29
7.2.2 Proceeding overview ............................................................................................................... 29
7.2.3 Proceeding in detail................................................................................................................. 30
8. PROGRAM EDITOR ............................................................................................. 35
8.1 Selecting between set-point ramp and set-point step ....................................................................... 35
8.1.1 Programming with setting “Ramp” (default setting) ................................................................ 35
8.1.2 Programming with setting “step” ............................................................................................. 37
8.1.3 General notes on programming temperature transitions ........................................................ 38
8.2 Set-point entry for program operation ............................................................................................... 38
8.3 Program table template ..................................................................................................................... 41
8.4 Deleting a program section ............................................................................................................... 42

VD (E2.1) 09/2018 page 2/95

9. PROGRAM START LEVEL .................................................................................. 43

10. USER LEVEL ....................................................................................................... 46

11. PERFORMANCE IN CASE OF FAILURES .......................................................... 52

11.1 Performance after power failure ........................................................................................................ 52
11.2 Alarm messages ............................................................................................................................... 52
12. TEMPERATURE SAFETY DEVICE CLASS 2 ..................................................... 52

13. REFERENCE MEASUREMENTS. CHECKING THE TEMPERATURE IN THE

INNER CHAMBER................................................................................................ 54

14. COMMISSIONING THE VACUUM ....................................................................... 54

14.1 Evacuation ......................................................................................................................................... 55
14.2 Breaking the vacuum (flooding with ambient air) .............................................................................. 55
14.3 Operation with inert gas .................................................................................................................... 56
15. SWITCHING CONTACTS 24V DC VIA OPERATION LINES............................... 57

16. OPTIONS .............................................................................................................. 58

16.1 Connection kit VD (option) ................................................................................................................ 58
16.2 Vacuum module empty (without pump) (option) ............................................................................... 58
16.3 Vacuum module with chemical membrane pump VP 1.1 or VP 2.1 (option) .................................... 60
16.4 Vacuum module with speed controlled chemical membrane pump VP 3.1 and vacuum controller
(option) .............................................................................................................................................. 62
16.5 Digital pressure display (option) ........................................................................................................ 64
16.6 Additional measuring channel for digital object temperature display with flexible Pt 100 temperature
sensor (option) .................................................................................................................................. 64
16.7 Measuring access port vacuum 9 poles (option)............................................................................... 65
16.8 Communication software APT-COM™ 3 DataControlSystem (option) ............................................. 66
17. MAINTENANCE, CLEANING, AND SERVICE ..................................................... 66
17.1 Maintenance intervals, service .......................................................................................................... 66
17.2 Cleaning and decontamination .......................................................................................................... 67
17.2.1 Cleaning .................................................................................................................................. 67
17.2.2 Decontamination ..................................................................................................................... 68
17.3 Sending the chamber back to BINDER GmbH ................................................................................. 70
18. DISPOSAL............................................................................................................ 70
18.1 Disposal of the transport packing ...................................................................................................... 70
18.2 Decommissioning .............................................................................................................................. 71
18.3 Disposal of the chamber in the Federal Republic of Germany.......................................................... 71
18.4 Disposal of the chamber in the member states of the EU except for the Federal Republic of
Germany............................................................................................................................................ 72
18.5 Disposal of the chamber in non-member states of the EU ............................................................... 74
19. TROUBLESHOOTING ......................................................................................... 74

20. TECHNICAL DESCRIPTION ................................................................................ 76

20.1 Factory calibration and adjustment ................................................................................................... 76
20.2 Technical data ................................................................................................................................... 76
20.3 Equipment and options (extract) ....................................................................................................... 78
20.4 Accessories and spare parts (extract)............................................................................................... 79
20.5 Dimensions VD 23............................................................................................................................. 81
20.6 Dimensions VD 53............................................................................................................................. 82
20.7 Dimensions VD 115........................................................................................................................... 83

VD (E2.1) 09/2018 page 3/95

21. CERTIFICATES AND DECLARATIONS OF CONFORMITY ............................... 84
21.1 EU Declaration of Conformity ............................................................................................................ 84
21.2 Certificate for the GS mark of conformity of the “Deutsche Gesetzliche Unfallversicherung e.V.“
(German Social Accident Insurance) DGUV ..................................................................................... 87
22. PRODUCT REGISTRATION ................................................................................ 89

23. CONTAMINATION CLEARANCE CERTIFICATE ................................................ 90

23.1 For chambers located outside USA and Canada .............................................................................. 90
23.2 For chambers located in USA and Canada ....................................................................................... 93

VD (E2.1) 09/2018 page 4/95

Dear customer,
For the correct operation of the program controlled vacuum drying oven VD, it is important that you read
this operating manual completely and carefully and observe all instructions as indicated. Failure to read,
understand and follow the instructions may result in personal injury. It can also lead to damage to the
chamber and/or poor equipment performance.

1. Safety
This operating manual is part of the components of delivery. Always keep it handy for reference. The
device should only be operated by laboratory personnel especially trained for this purpose and familiar
with all precautionary measures required for working in a laboratory. Observe the national regulations on
minimum age of laboratory personnel. To avoid injuries and property damage observe the safety
instructions of the operating manual.

WARNING
Failure to observe the safety instructions.
Serious injuries and chamber damage.
 Observe the safety instructions in this operating manual.
 Carefully read the complete operating instructions of the VD vacuum drying oven.

1.1 Legal considerations

This operating manual is for informational purposes only. It contains information for installing, start-up,
operation and maintenance of the product. Note: the contents and the product described are subject to
change without notice.
Understanding and observing the instructions in this operating manual are prerequisites for hazard-free
use and safety during operation and maintenance. In no event shall BINDER be held liable for any
damages, direct or incidental arising out of or related to the use of this manual.
This operating manual cannot cover all conceivable applications. If you would like additional information,
or if special problems arise that are not sufficiently addressed in this manual, please ask your dealer or
contact us directly by phone at the number located on page one of this manual
Furthermore, we emphasize that the contents of this operating manual are not part of an earlier or existing
agreement, description, or legal relationship, nor do they modify such a relationship. All obligations on the
part of BINDER derive from the respective purchase contract, which also contains the entire and
exclusively valid statement of warranty administration. The statements in this manual neither augment nor
restrict the contractual warranty provisions.
Have repairs performed only by experts authorized by BINDER. Repaired chambers must comply with the
quality standard specified by BINDER.

1.2 Structure of the safety instructions

In this operating manual, the following safety definitions and symbols indicate dangerous situations
following the harmonization of ISO 3864-2 and ANSI Z535.6.

1.2.1 Signal word panel

Depending on the probability of serious consequences, potential dangers are identified with a signal word,
the corresponding safety color, and if appropriate, the safety alert symbol.

DANGER
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious
(irreversible) injury.

VD (E2.1) 09/2018 page 5/95

 WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
(irreversible) injury.

CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor
(reversible) injury.

CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in damage to the product
and/or its functions or to property in its proximity.

1.2.2 Safety alert symbol

Use of the safety alert symbol indicates a risk of injury.

Observe all measures that are marked with the safety alert symbol in order to avoid death or
injury.

1.2.3 Pictograms

Warning signs

Electrical hazard Hot surface Explosive atmosphere Stability hazard

Lifting hazard Inhalation hazard Suffocation hazard Harmful substances

Biohazard Risk of corrosion and / Pollution Hazard

or chemical burns
Mandatory action signs

Mandatory regulation Read operating Disconnect the power Lift with several persons
instructions plug

Environment protection Wear protective gloves Wear safety goggles

VD (E2.1) 09/2018 page 6/95

Prohibition signs

Do NOT touch Do NOT spray with

water

Information to be observed in order to ensure optimum function of the product.

1.2.4 Word message panel structure

Type / cause of hazard.

Possible consequences.
∅ Instruction how to avoid the hazard: prohibition
 Instruction how to avoid the hazard: mandatory action

Observe all other notes and information not necessarily emphasized in the same way, in order to avoid
disruptions that could result in direct or indirect injury or property damage.

1.3 Localization / position of safety labels on the chamber

The following labels are located on the chamber:
Pictograms (Warning signs)

Hot surface
(on the outer chamber door)

Service label

Figure 1: Position of labels on the chamber

Keep safety labels complete and legible.

Replace safety labels that are no longer legible. Contact BINDER Service for these replacements.

VD (E2.1) 09/2018 page 7/95

1.4 Type plate
The type plate sticks to the left side of the chamber, bottom right-hand.

Nominal temp. 200 °C 0,80 kW / 3,5 A

392 °F 230 V / 50 Hz
IP protection 20 230 V / 60 Hz
Safety device DIN 12880 1N~
Class 2.0
Art. No. 9030-0029
Project No. Vacuum Drying Oven
Built 2018
BINDER GmbH
Im Mittleren Ösch 5 VD 23 Serial No. 00000000000000
78532 Tuttlingen / Germany E2.1 Made in Germany
www.binder-world.com

Figure 2: Type plate (example of VD 23 regular chamber)

Indications of the type plate Information

(example)
BINDER Manufacturer: BINDER GmbH
VD 23 Model designation
Vacuum Drying Oven Device name
Serial No. 000000000000 Serial no. of the chamber
Built 2018 Year of construction
Nominal 200 °C Nominal temperature
temperature 392 °F
IP protection 20 IP type of protection acc. to standard EN 60529
Temp. safety device DIN 12880 Temperature safety device acc. to standard DIN 12880:2007
Class 2.0 Class of temperature safety device
Art. No. 9030-0029 Art. no. of the chamber
Project No. --- Optional: Special application acc. to project no.
0,80 kW Nominal power
3,5 A Nominal current
230 V / 50 Hz Nominal voltage +/- 10%
230 V / 60 Hz at the indicated power frequency
1N~ Current type

Symbol on the type plate Information

CE conformity marking

Electrical and electronic equipment manufactured / placed on

the market in the EC after 13 August 2005 and to be
disposed of in a separate collection according to Directive
2012/19/EU on waste electrical and electronic equipment
(WEEE).
GS mark of conformity of the “Deutsche Gesetzliche
Unfallversicherung e.V. (DGUV), Prüf- und
Zertifizierungsstelle Nahrungsmittel und Verpackung im
DGUV Test“ (German Social Accident Insurance (DGUV),
Testing and Certification Body for Foodstuffs and Packaging
Industry in DGUV Test).
(Not valid for UL chambers)

VD (E2.1) 09/2018 page 8/95

Symbol on the type plate Information
The chamber is certified according to Customs Union Technical
Regulation (CU TR) for the Eurasian Economic Union (Russia,
Belarus, Armenia, Kazakhstan Kyrgyzstan).
®
The chamber is certified by Underwriters Laboratories Inc. according
to the following standards:
(VD-UL only) • UL 61010A-1, UL 61010A-2-10
• CSA C22.2 No. 1010.1-92, CSA C22.2 No. 1010.2.010-94

1.5 General safety instructions on installing and operating the chamber

With regard to operating the chamber and to the installation location, please observe the DGUV guidelines
213-850 on safe working in laboratories (formerly BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued
by the employers’ liability insurance association) (for Germany).
BINDER GmbH is only responsible for the safety features of the chamber provided skilled electricians or
qualified personnel authorized by BINDER perform all maintenance and repair, and if components relating
to chamber safety are replaced in the event of failure with original spare parts.
To operate the chamber, use only original BINDER accessories or accessories from third-party suppliers
authorized by BINDER. The user is responsible for any risk caused by using unauthorized accessories.

CAUTION
Danger of overheating.
Damage to the chamber.
∅ Do NOT install the oven in unventilated recesses.
 Ensure sufficient ventilation for dispersal of the heat.

Do not operate the chamber in hazardous locations.

DANGER
Explosion hazard.
Danger of death.
∅ Do NOT operate the chamber in potentially explosive areas.
 KEEP explosive dust or air-solvent mixtures AWAY from the chamber.

The chamber is regularly equipped with a large-surface area safety valve. The window, manufactured in
toughened safety glass, is elastic-mounted and serves as a safety valve in the event of explosion. The
additional plastic panel provides splinter protection.

DANGER
Explosion hazard.
Danger of death.
∅ Do NOT introduce any substance into the oven which is combustible or explosive at
working temperature.
∅ NO explosive dust or air-solvent mixture in the inner chamber.
∅ Do NOT use the vacuum drying oven for drying or heat treatments leading to release of
combustible vapors able to form an explosive mixture with air.

VD (E2.1) 09/2018 page 9/95

Any solvent contained in the charging material must not be explosive or inflammable. I.e., irrespective of
the solvent concentration in the steam room, NO explosive mixture with air must form. The drying
temperature must lie below the flash point or below the sublimation point of the charging material.
Familiarize yourself with the physical and chemical properties of the charging material, as well as the
contained moisture constituent and its behavior with the addition of heat energy and changes in pressure.
Familiarize yourself with any potential health risks caused by the charging material, the contained moisture
constituent or by reaction products that may arise during the drying process. Take adequate measures to
exclude such risks prior to putting the chamber into operation.

DANGER
Electrical hazard.
Danger of death.
∅ The oven must NOT become wet during operation or maintenance.

The chambers were produced in accordance with the relevant VDE regulations and were routinely tested
in accordance to VDE 0411-1 (IEC 61010-1).
During and shortly after operation, the temperature of the inner surfaces almost equals the set-point.

CAUTION
The inner chamber will become hot during operation.
Danger of burning.
∅ Do NOT touch the inner surfaces or the charging material during operation.

In the case of operation with inert gas, the chamber is supplied with an oxygen-displacing gas (e.g. N2).
The gas emerging from the system must therefore be removed from the installation area by means of a
suitable extraction system (see technical ventilation measures in the DGUV guidelines 213-850 on safe
working in laboratories (formerly BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued by the
employers’ liability insurance association) (for Germany).

With use of a vacuum system or a vacuum pump, observe the permitted gas inlet
temperature. Observe the safety instructions of the pump manufacturer.

VD (E2.1) 09/2018 page 10/95

1.6 Intended use
The VD vacuum drying ovens are suitable for drying and heat treatment of solid or pulverized charging
material, as well as bulk material, using the supply of heat under vacuum. The solvent content must not be
explosive or flammable. A mixture of any component of the charging material with air must NOT be
explosive. The drying temperature must lie below the flash point or below the sublimation point of the
charging material. Any component of the charging material must NOT be able to release toxic gases.
Other applications are not approved.
The chambers are not classified as medical devices as defined by the Medical Device Directive
93/42/EEC.

Observing the instructions in this operating manual and conducting regular maintenance work
(chap. 17) is part of the intended use.

The charging material shall not contain any corrosive ingredients that may damage the
machine components made of stainless steel and aluminum. Such ingredients include in
particular acids and halides. Any corrosive damage caused by such ingredients is excluded
from liability by BINDER GmbH.

DANGER
Explosion or implosion hazard.
Danger of poisoning.
Danger of death.
∅ Do NOT introduce any substance combustible or explosive at working temperature into
the chamber, in particular no energy sources such as batteries or lithium-ion batteries
∅ NO explosive dust or air-solvent mixture in the inner chamber.
∅ Do NOT introduce any substance which could lead to release of toxic gases.

In case of foreseeable use of the chamber there is no risk for the user through the integration of the
chamber into systems or by special environmental or operating conditions in the sense of EN 61010-
1:2010. For this, the intended use of the chamber and all its connections must be observed.

1.7 Operating instructions

Depending on the application and location of the chamber, the operator of the chamber must provide the
relevant information for safe operation of the chamber in a set of operating instructions.

Keep these operating instructions with the chamber at all times in a place where they are
clearly visible. They must be comprehensible and written in the language of the employees.

VD (E2.1) 09/2018 page 11/95

1.8 Measures to prevent accidents
The manufacturer took the following measures to prevent ignition and explosions:
• Indications on the type plate
See operating manual chap. 1.4.
• Operating manual
An operating manual is available for each chamber.
• Overtemperature monitoring
The chamber is equipped with a temperature display, which can be read from outside.
The chamber is equipped with an additional safety controller (temperature safety device class 2 acc. to
DIN 12880:2007). Visual and audible (buzzer) signals indicate temperature exceeding.
• Safety, measurement, and control equipment
The safety, measuring, and control equipment is easily accessible.
• Electrostatic charge
The interior parts are grounded.
• Non-ionizing radiation
Non-ionizing radiation is not intentionally produced, but released only for technical reasons by electrical
equipment (e.g. electric motors, power cables, solenoids). The machine has no permanent magnets. If
persons with active implants (e.g. pacemakers, defibrillators) keep a safe distance (distance of field
source to implant) of 30 cm, an influence of these implants can be excluded with high probability.
• Protection against touchable surfaces
Tested according to EN ISO 13732-1:2008.
• Floors
See operating manual chap. 3.4 for correct installation
• Cleaning
See operating manual chap. 17.2.
• Examinations
The chamber has been inspected by the “Deutsche Gesetzliche Unfallversicherung e.V. (DGUV)
(German Social Accident Insurance (DGUV)” (German Social Accident Insurance (DGUV), Testing
and Certification Body for Foodstuffs and Packaging Industry in DGUV Test) and bears the GS mark.
(Not valid for UL chambers)
®
UL chambers only: The chamber is certified by Underwriters Laboratories Inc. according to the
standards UL 61010A-1, UL 61010A-2-10, CSA C22.2 No. 1010.1-92, CSA C22.2 No. 1010.2.010-94.

VD (E2.1) 09/2018 page 12/95

2. Description of the equipment
Vacuum drying is used for special drying problems, for which conventional drying methods cannot offer a
solution due to physical limitations.
All functions of the multifunctional program control can be set simply and conveniently via the easy to
understand function keypad of the RD3 temperature program controller. This controller is equipped with
touch function keys and a digital display and permits exact temperature setting and programming
temperature cycles. The VD provides almost unlimited possibilities of adapting to individual customer
requirements based upon extensive programming options and on the week program timer and real time
clock of the controller.
The inner chamber is made of especially corrosion resistant stainless steel V4A (German material no.
1.4404 2B, US equivalent AISI 316L) micro-polished. The rack holder and all of the chamber's vacuum
connections and valves are made of especially corrosion resistant stainless steel V4A (German material
no. 1.4571, US equivalent AISI 316Ti). The housing is RAL 7035 powder-coated. All corners and edges
are also completely coated. When operating the chamber at temperatures above 150 °C / 302 °F, the
impact of the oxygen in the air may cause discoloration of the metallic surfaces (yellowish-brown or blue)
by natural oxidation processes. These colorations are harmless and will in no way impair the function or
quality of the chamber.
The chambers are jacket-heated. The APT.line™ preheating chamber technique ensures a completely
homogeneous jacket temperature, ensuring uniform heat transfer into the inner chamber. The low-loss
heat transfer to the material uses the patented aluminum vacuum expansion racks (or optionally available
in stainless steel). The elastic-mounted safety glass window reliably compensates any overpressure or
explosions that may occur. The additional polycarbonate panel ensures proven and effective splinter
protection in the event of an implosion.
All VD chambers provide an inert gas connection and a measuring connection serving to connect a
vacuum controller or a measuring access port.
The chambers are equipped as standard with a large-surface safety valve. The toughened safety glass
window is elastic-mounted and in the event of explosion serves as a safety valve. The additional plastic
panel provides splinter protection.
The chambers are equipped with a serial interface RS 422 for computer communication, e.g. via the
communication software APT-COM™ 3 DataControlSystem (option, chap.16.8). For further options, see
chap. 20.3.
All installable items, such as racks and rack holders, can be easily removed. The completely smooth inner
chamber with its rounded corners and internally welded seams is easy to clean.
The minimum working temperature of the vacuum drying oven is approx. 15 °C / 27 °F above room
temperature. The maximum temperature is 200 °C / 392 °F.
3 3
Vacuum pumps with a suction capacity of 1 m /h to 30 m /h are suitable for the VD vacuum drying oven.
-2
The permissible end vacuum is 10 mbar / 0.0003 inHg.

VD (E2.1) 09/2018 page 13/95

2.1 Chamber overview

(A)

(B)

(C)

(D)

(E)

Figure 3: VD 23 with option vacuum module and chemical membrane pump

(A) Control panel and instrument box

(B) Chamber door
(C) Elastic-mounted safety glass window
(D) Vacuum module (option)
(E) Chemical membrane pump (option)

VD (E2.1) 09/2018 page 14/95

2.2 VD 23 control panel
(7) (8) (4) (3) (2) (2a) (1)

AIR/GAS

VAC.OFF

VAC.ON

Figure 4: VD 23 control panel

(1) On/off switch (main power switch)

(2) Temperature safety device class 2
(2a) Red alarm lamp of the safety device class 2
(3) Manometer (pressure reading)
(4) Aeration valve (inert gas or ambient air)
(7) Program controller RD3
(8) Vacuum shut-off valve

2.3 VD 53 / 115 control panel

(8) (7) (6) (5) (3) (2) (2a) (1)

VAC.OFF AIR

GAS
VAC.ON

Figure 5: VD 53/115 control panel

(1) On/off switch (main power switch)

(2) Temperature safety device class 2
(2a) Red alarm lamp of the safety device class 2
(3) Manometer (pressure reading)
(5) Aeration valve (ambient air)
(6) Fine dosing valve (inert gas)
(7) Program controller RD3
(8) Vacuum shut-off valve

VD (E2.1) 09/2018 page 15/95

2.4 Connections at the rear of the chamber

(10) (11) (12) (13) (14) (15) (16) (9)

(17)

Figure 6: Rear of VD

(9) RS 422 serial interface for computer communication

(10) Miniature fuse
(11) Power connection line
(12) Inert gas connection, adapter with hose olive ∅ 8 mm / 0.31 in
(VD23: also fresh air inlet)
(13) Vacuum connection with small flange DN16
(14) DIN socket (option) for option “object temperature display”
(15) DIN socket (operation line 2) (option) for option “program controlled venting”
(16) DIN socket (operation line 1) (option) for option “vacuum module with pump”
(17) Measuring connection with small flange DN16

VD (E2.1) 09/2018 page 16/95

3. Completeness of delivery, transportation, storage, and
installation

3.1 Unpacking, and checking equipment and completeness of delivery

After unpacking, please check the chamber and its optional accessories, if any, based on the delivery
receipt for completeness and for transportation damage. Inform the carrier immediately if transportation
damage has occurred.
The final tests of the manufacturer may have caused traces of the shelves on the inner surfaces. This has
no impact on the function and performance of the chamber.
Please remove any transportation protection devices and adhesives in/on the chamber and on the doors
and remove the operating manuals and accessory equipment.

CAUTION
Sliding or tilting of the chamber.
Damage to the chamber.
Risk of injury by lifting heavy loads.
∅ Do NOT lift or transport the chamber using the door handle, the door or the lower
housing.
 Lift chambers size 23 and 53 from the pallet at the four lower corners with the aid of 4
people.
 Lift chambers size 115 from the pallet with the aid of 6 people.

If you need to return the chamber, please use the original packing and observe the guidelines for safe
lifting and transportation (chap. 3.2).
For disposal of the transport packing, see chap. 18.1.
If you ordered the option “vacuum module with chemical membrane pump”, the pump will be delivered in a
separate box and must be fitted into the module and connected at the place of installation (see chap. 16.3
and 16.4).
Note on second-hand chambers (Ex-Demo-Units):
Second-hand chambers are chambers that were used for a short time for tests or exhibitions. They are
thoroughly tested before resale. BINDER ensures that the chamber is technically sound and will work
flawlessly.
Second-hand chambers are marked with a sticker on the chamber door. Please remove the sticker before
commissioning the chamber.

VD (E2.1) 09/2018 page 17/95

3.2 Guidelines for safe lifting and transportation
After operation, please observe the guidelines for temporarily decommissioning the chamber (chap. 18.2).

CAUTION
Sliding or tilting of the chamber.
Damage to the chamber.
Risk of injury by lifting heavy loads.
 Transport the chamber in its original packaging only.
 For moving or shipping, secure the oven with transport straps.
∅ Do NOT lift or transport the chamber using the door, the handle, or the lower housing.
 Lift chambers size 23 and 53 at the four lower corners with the aid of 4 people.
 Lift chambers size 115 with the aid of 6 people.

• Permissible ambient temperature range during transport: -10 °C / 14°F to +60 °C / 140°F.
You can order transport packing for moving or shipping purposes from BINDER Service.

3.3 Storage
Intermediate storage of the chamber in a closed and dry room. Observe the guidelines for temporary
decommissioning (chap. 18.2).
• Permissible ambient temperature range during storage: -10 °C / 14°F to +60 °C / 140°F.
• Permissible ambient humidity: max. 70 % r.H., non-condensing
When after storage in a cold location you transfer the chamber to its warmer installation site,
condensation may form. Before start-up, wait at least one hour until the chamber has attained ambient
temperature and is completely dry.

3.4 Location of installation and ambient conditions

Set up the VD vacuum drying oven on a flat, even, and non-flammable surface, free from vibration, in a
well-ventilated, dry location. Align it using a spirit level. The site of installation must be capable of
supporting the chamber’s weight (see technical data, chap. 20.2). The chambers are designed for setting
up inside a building (indoor use).

CAUTION
Danger of overheating.
Damage to the chamber.
∅ Do NOT set up chambers in non-ventilated recesses.
 Ensure sufficient ventilation for dispersal of the heat.

• Permissible ambient temperature range during operation: +18 °C / 64°F to +32 °C / 90°F.

The ambient temperature should not be substantially higher than the indicated ambient
temperature of +25 °C / 77°F to which the specified technical data relate. Deviations from the
indicated data are possible for other ambient conditions.

• Permissible ambient humidity: 70 % r.H. max., non-condensing.

• Installation height: max. 2000 m / 6562 ft above sea level.

VD (E2.1) 09/2018 page 18/95

When placing several chambers of the same size side by side, maintain a minimum distance of 250 mm /
9.8 in between each chamber. Wall distances: rear 100 mm / 3.9 in, sides 135 mm / 5.3 in. Spacing above
and behind the chamber of at least 100 mm / 3.9 in must also be maintained.

CAUTION
Danger by stacking.
Damage to the chambers.
∅ Do NOT place vacuum drying ovens on top of each other.

To completely separate the chamber from the power supply, you must disconnect the power plug. Install
the chamber in a way that the power plug is easily accessible and can be easily pulled in case of danger.
For the user there is no risk of temporary overvoltages in the sense of EN 61010-1:2010.
Do not install or operate the vacuum drying oven VD in potentially explosive areas.

DANGER
Explosion hazard.
Danger of death.
∅ Do NOT operate the chamber in potentially explosive areas.
 KEEP explosive dust or air-solvent mixtures AWAY from the vicinity of the chamber.

The maximum permissible ambient temperature of the vacuum pumps delivered by BINDER is 40 °C /
104°F.

Notes when using inert gas:

When operating the VD vacuum drying oven with inert gas, correctly follow the technical ventilation
measures, as described in the DGUV guidelines 213-850 on safe working in laboratories (formerly
BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued by the employers’ liability insurance association)
(for Germany).
For operation with inert gas, the chamber is supplied with an oxygen-displacing gas, e.g. N2. Inert gases in
high concentrations are hazardous to health. They are colorless and almost odorless and therefore
practically imperceptible. Inhalation of inert gases can cause drowsiness up to respiratory arrest. When
the O2 content of the air decreases below 18%, there is risk of death from lack of oxygen. Any gas that
might escape has to be led out via good room ventilation or a suitable exhaust system.

WARNING
High concentration of inert gas.
Risk of death by suffocation.
∅ Do NOT set up chambers in non-ventilated recesses.
 Ensure technical ventilation measures.
 Respect the relevant regulations for handling these gases.
 When decommissioning the vacuum drying oven, shut off the inert gas supply: Close
valves (4) or (6).

VD (E2.1) 09/2018 page 19/95

4. Installation and connections

4.1 Vacuum expansion racks

The low-loss heat transfer to the material occurs via the
patented aluminum vacuum expansion racks (also available in
stainless steel as an option). The strong tension causes the
racks to fit tightly against the interior wall and their large-
surface contact area ensures rapid and effective heat transfer.
The removable rack holders allow for easy positioning.
You can also remove the expansion racks for easy cleaning.
Do not remove them too often in order to prevent wear.

Figure 7: Using the expansion racks

• Pushing the locking lever: The expansion rack is released and can be removed.
• Pulling the locking lever: The expansion rack is pressed against the inner chamber walls.

Following each new tightening of an expansion rack, check that the lateral parts of the rack fit
closely over their whole surface to the inner chamber wall. This is necessary in order to ensure
the specified temperature exactitude.

CAUTION
Invalid calibration.
∅ Do NOT change between aluminum and stainless steel racks
 Use the delivered expansion racks only

4.2 Vacuum connection

Always connect the VD vacuum drying oven to a vacuum pump or to a domestic vacuum system. For this
purpose, the vacuum connection (13) with small flange DN16 must be connected to the back of the
chamber at the top with the vacuum pump or domestic vacuum system via a vacuum suction hose. For
connecting to the chamber, BINDER recommends the connection kit VD, Art. no. 8012-0146.
With the option “stainless steel tubing” between the vacuum oven and vacuum module, the vacuum
connection is already located inside the vacuum module.

Vacuum pumps with a suction capacity of 1-30 m³/h are suitable for the VD vacuum drying
-2
oven. Permissible end vacuum: 10 mbar / 0.0003 inHg.

4.3 Inert gas connection

When operating the VD vacuum drying oven with inert gas, correctly follow the technical ventilation
measures, as described in the DGUV guidelines 213-850 on safe working in laboratories (formerly
BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued by the employers’ liability insurance association)
(for Germany).
Connect the inert gas supply to the inert gas connection (adapter with hose olive diameter 8 mm / 0.31 in)
via a pressure reducer. Screw the enclosed adapter with hose olive on the thread (12) at the chamber
rear. Set the pressure reducer to a pressure slightly above ambient pressure. Ensure that the pressure
reducer will certainly open. Do not alter this setting in order to avoid perturbation inside the oven and
release of big quantities of inert gas after flooding the VD.

VD (E2.1) 09/2018 page 20/95

Inert gases in high concentrations are hazardous to health. They are colorless and almost odorless and
therefore practically imperceptible. Inhalation of inert gases can cause drowsiness up to respiratory arrest.
When the O2 content of the air decreases below 18%, there is risk of death from lack of oxygen. Any gas
that might escape has to be led out via good room ventilation or a suitable exhaust system.

WARNING
High concentration of inert gas.
Risk of death by suffocation.
∅ Do NOT set up chambers in non-ventilated recesses.
 Ensure technical ventilation measures.
 Respect the relevant regulations for handling these gases.
 When decommissioning the vacuum drying oven, shut off the inert gas supply: Close
valves (4) or (6).

4.4 Electrical connection

The chambers are supplied ready for connection. They come with a fixed power connection cable of at
least 1800 mm / 70.87 in in length.

Nominal voltage ± 10% at the Current Chamber

Model Power plug
indicated power frequency type fuse
VD 23 230 V at 50 Hz
VD 53 Grounded plug 1N~ 10 A
VD 115 230 V at 60 Hz
VD 23-UL
NEMA 5-15P 115 V at 60 Hz 1N~ 12,5 A
VD 53-UL
VD 115-UL NEMA 5-20P 115 V at 60 Hz 1N~ 20 A

• The domestic socket must also provide a protective conductor. Make sure that the connection of the
protective conductor of the domestic installations to the chamber’s protective conductor meets the
latest technology. The protective conductors of the socket and plug must be compatible!
• Prior to connection and start-up, check the power supply voltage. Compare the values to the specified
data located on the chamber’s type plate (chamber front behind the door, bottom left-hand, see chap.
1.4).
• When connecting, please observe the regulations specified by the local electricity supply company and
as well as the VDE directives (for Germany). We recommend the use of a residual current circuit
breaker.
• Pollution degree (acc. to IEC 61010-1): 2
• Over-voltage category (acc. to IEC 61010-1): II

CAUTION
Danger of incorrect power supply voltage.
Damage to the equipment.
 Check the power supply voltage before connection and start-up.
 Compare the power supply voltage with the data indicated on the type plate.

See also electrical data (chap. 20.2).

To completely separate the chamber from the power supply, you must disconnect the power
plug. Install the chamber in a way that the power plug is easily accessible and can be easily
pulled in case of danger.

VD (E2.1) 09/2018 page 21/95

5. Start up
After connecting the supply lines (chap 4), turn on the chamber via the main power switch (1):
• Position 0: Oven without function
• Position I: Oven operating
Warming chambers may release odors in the first few days after commissioning. This is not a quality
defect. To reduce odors quickly we recommend heating up the chamber to its nominal temperature for
one day and in a well-ventilated location.

5.1 Settings at the RD3 program controller

After turning on the chamber at the main power switch (1), the controller is in Normal Display / Fixed value
operation mode.
Depending on the temperature value entered before, LED (7a) is lit if the heating is active, or no LED is lit
if the actual temperature is equal to or above the set-point.
In Display 1 of the controller the actual temperature value is displayed.
• With inactive week program timer:
In Display 2 of the controller the actual date and time are displayed. Example:

15.05.06 13:52

• With active week program timer:

In Display 2 of the controller the actual date and time and the states of the week program timer
channels are displayed. Examples:

15.05.06 13:52 - - 15.05.06 13:52 - � 15.05.06 13:52 � - 15.05.06 13:52 � �

Channel 1 Off, Channel 1: Off, Channel 1: On, Channel 1 On,
Channel 2: Off Channel 2: On Channel 2: Off Channel 2: On

(7a) LED Heating active

(7b) LED Operation line 1 ON

Display 1
(7c) LED Operation line 2 ON

(7d)
LED lit: program operation
LED flashing: exceeding of the
Display 2 tolerance limits in “Fixed value
entry mode” or in “Program
operation”. In program operation:
program interruption.

Figure 8: RD3 program controller

VD (E2.1) 09/2018 page 22/95

The program controller RD3 permits programming temperature cycles.
You can enter two programs with up to 10 sections each or one program with up to 20 sections (setting in
the user level, chap. 10).

When changing from 2 programs to 1 program or vice-versa, existing programs are deleted.

The maximum length of an individual program section can be set to either 99 h 59 min or to 999 h 59 min
(setting in the user level, chap. 10). This setting is then valid for all program sections.
Programming can be done directly through the keypad of the controller or graphically through the software
APT-COM™ 3 DataControlSystem (option, chap. 16.8) specially developed by BINDER.

5.2 General indications on the RD3 program controller

The program controller RD3 offers several functional levels:
Normal Display / Fixed value operation:
• Display of the temperature actual value (display 1) and of the actual date and time (display 2).
• The oven is in fixed value operating mode, equilibrating to the entered set-points.
Fixed value entry mode (chap. 6)
• Entry of the temperature set-point for fixed value operating mode
• Entry of temperature set-points 1 and 2 for week program operation
Program editor (chap. 8)
• You can enter two programs with up to 10 sections each or one program with up to 20 sections
(selection in the user level, chap. 10). Entry of temperature set-points in all program sections (chap.
8.1).
• Deleting a program section (chap. 8.4)
Program start level (chap. 9)
• Selection of an entered program
• Entry of settings affecting the program course, as “start delay time” or “number of program cycles”
• Program start
Week program editor (chap.7)
• Setting the shift points
User level (chap. 10)
• User specific controller settings
• Setting the real time clock

VD (E2.1) 09/2018 page 23/95

 Normal Display / Fixed value operation

5 seconds

Fixed value entry mode Program editor Program start level

5 seconds

Menu visible only if week program

Week program editor
timer is activated in the user level

5 seconds

User level

If no button is touched during more than 120 sec., the controller returns from the current level to Normal
Display.

VD (E2.1) 09/2018 page 24/95

6. Fixed value entry mode
If you do not want to use the week program timer, deactivate it (factory setting, setting in the
user level, chap. 10) before entering any set-points. Any setting of the operation lines in fixed
value entry mode is ineffective with active week program timer.

Basic entry principle: Access the individual parameters with button X/W. Enter the value with the arrow
keys. A value flashing once after 2 seconds indicates that it has been applied by the controller.
Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
Display 2 shows e.g. 15.05.06 13:52 - - (actual date and time)
(actual switching state of week program timer channel 1: Off,
channel 2: Off, visible only if week program timer is activated
in the user level, chap. 10)
Press key
C
Display 1 shows e.g. 40.0 (actual temperature set-point 1)
Display 2 shows SP1 TEMPERATURE (variable: temperature in °C)
Enter temperature set-point in °C using Value is shown in display 1.
arrow keys
Press key
C
Display 1 shows e.g. 50.0 (actual temperature set-point 2)
(visible only if week program timer is activated
in the user level, chap. 10)
Display 2 shows SP2 TEMPERATURE (variable: temperature in °C)
Enter temperature set-point in °C using Value is shown in display 1.
arrow keys
Press key

Display 1 shows e.g. 000 (actual switching state of operation lines)

Display 2 shows OPERATION LINE (variable: switching state of operation lines)
Enter switching state of operation lines using (see chap. 15, switching outputs via operation
arrow keys lines)
Press key

If no button is pressed within more than 120 sec, or if the EXIT button is pressed, the controller changes
to Normal Display.

When changing the set-point, check the setting of the safety device (chap. 12).

The values entered in fixed-value entry mode remain valid after program run-off and are then
equilibrated.

If the week program timer is active, depending on the running week program another set-point (SP2) may
be targeted. Temperatures too high or too low for the introduced solvent quantity can occur. Deactivate
the week program timer if you do not use it (default setting, setting in the User level, chap. 10).

VD (E2.1) 09/2018 page 25/95

 CAUTION
Too high or too low temperature.
Damage to the charging material.
 Deactivate the week program timer if you do not use it.

7. Week program editor

The Week program editor permits defining up to 4 shift point for each week day. A shift point defines a
moment and the switching state ON or OFF of the channels that become active in this instance.
Channel function:
• Channel 1 On = Set-point SP2 is equilibrated.
• Channel 1 Off = Set-point SP1 is equilibrated
• Channel 2 = reserve

The week program timer is initially set to inactive (factory setting). Therefore, you need to
activate the week program timer in the user level (chap. 10).

Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
Display 2 shows (actual date and time, actual state of week program timer
e.g. 15.05.06 13:52 - -
channel 1: Off, channel 2: Off)
Press down key for 5 sec

Display 1 shows e.g. 0000

Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press down key for 5 sec

Display 1 shows 0000 Menu visible only if week program timer is activated
in the user level (chap. 10)
Display 2 shows WEEK PROG. EDITOR (you are in the week program editor)
Press program key

Display 1 shows 0000

Display 2 shows UserCod? 0000 (enter user code, display flashes)
Enter the user code using arrow keys e.g. 0001 (basic setting, adjustable in the
user level, chap. 10).
Value is shown in both displays.
Automatically forward after 2 sec
Display 1 shows 0000
Display 2 shows (selection of day of the week)
Monday
(actual selection: Monday)
Select the day of the week (Monday up to Day of the week is shown in display 2.
Sunday) with key

Press program key

VD (E2.1) 09/2018 page 26/95

 Display 1 shows 0000
Display 2 shows Shiftpt. (no function)
Press program key
Display 1 shows 0000
Display 2 shows (selection of the shift point)
Shiftpt. 1
(actual shift point: 1)
Select the shift point (1 up to 4) with key Value is shown in display 2.

Press program key

Display 1 shows e.g. --.-- (time of the selected shift point)
Display 2 shows (actual selection of the shift point: S1)
S1: --:--
(actual setting: shift point not programmed)
Press program key

Display 1 shows --.-- (time of the selected shift point)

Display 2 shows (entry of the time of the selected shift point)
Time --:--
(actual setting: shift point not programmed)
Enter the time (hh:mm) using arrow keys Value is shown in display 2.

Press key

Display 1 shows 0000

Display 2 shows (entry of the state of channel 1)
Ch1 = SP2: Off
(actual setting: Off)
Enter the state of channel 1 Setting is shown in display 2.
(On or Off) using arrow keys
Press key

Display 1 shows 0000

Display 2 shows (entry of the state of channel 2) (no function)
Channel 2: Off
(actual setting: Off)
Enter the state of channel 2 Setting is shown in display 2.
(On or Off) using arrow keys

Press key Press key EXIT

Display 1 shows e.g., 08.30 (time of the selected shift point)

Display 2 shows S1: 08:30 - - (actual selection of the shift point: S1)
(actual setting: time 08.30, channels Off)

Press program key Press key EXIT twice

Select the next shift point Select the next day of the week
To exit the menu, Press several times key EXIT or wait for 120 seconds. Controller returns to normal
display.

VD (E2.1) 09/2018 page 27/95

7.1 Program table template for Week program Editor

Program editor
Program title
Project
Date:

Day of the week Time Channel 1 Channel 2*

(temperature)
hh:mm AM PM ON = SP2 ON
OFF = SP1 OFF
Monday S1
S2
S3
S4
Tuesday S1
S2
S3
S4
Wednesday S1
S2
S3
S4
Thursday S1
S2
S3
S4
Friday S1
S2
S3
S4
Saturday S1
S2
S3
S4
Sunday S1
S2
S3
S4

* Channel 2 is non-functional in the standard chamber

VD (E2.1) 09/2018 page 28/95

7.2 Programming example of the Week program editor

7.2.1 Desired time function

During the day (12 hours) the oven shall maintain a temperature of +80 °C / 176°F, and during the night
(12 hours) it shall cool down / stop heating (set-point 30 °C / 86°F).
This program shall automatically run during the whole year, i.e. it shall be programmed just once.

7.2.2 Proceeding overview

1. Settings in the user level (see chap. 10)

• Activating the week program timer
• Checking and, if necessary, setting the real time clock

2. Enter the set-points for the week program in “Fixed value entry mode” (see chap. 6)
Set-points for the example program:
SP1 (night / weekend) = 30 °C (Channel 1 ON = Controller adjusts to set-point SP2)
SP2 (day / week) = 80 °C (Channel 1 OFF = Controller adjusts to set-point SP1)

3. Enter the time program to the program editor

Program table for the example program:

Day of the week Time Channel 1 (temperature)

hh:mm AM PM ON = SP2 (day)

OFF = SP1 (night)
Monday S1 06:00 ON
S2 18:00 OFF
Tuesday S1 06:00 ON
S2 18:00 OFF
Wednesday S1 06:00 ON
S2 18:00 OFF
Thursday S1 06:00 ON
S2 18:00 OFF
Friday S1 06:00 ON
S2 18:00 OFF
Saturday S1 06:00 ON
S2 18:00 OFF
Sunday S1 06:00 ON
S2 18:00 OFF

Make sure that no other shift points have been pre-programmed. If so, they must be deleted:
Set the time of the respective shift point to “ --:-- ” using key .

VD (E2.1) 09/2018 page 29/95

7.2.3 Proceeding in detail

1. Settings in the user level

• Activating the week program timer
• Checking and, if necessary, setting the real time clock
Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
Display 2 shows (actual date and time, actual switching state of week
e.g. 15.05.06 13:52 - -
program timer channel 1: Off, channel 2: Off)
Press down key for 5 sec

Display 1 shows e.g. 0000

Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press down key for 5 sec

Display 1 shows 0000 Menu visible only if week program timer is activated.
Display 2 shows WEEK PROG. EDITOR (you are in the week program editor)
Press down key for 5 sec

Display 1 shows 0000

Display 2 shows USER – LEVEL (you are in the user level)
Press program key
Display 1 shows 0000
Display 2 shows UserCod? 0000 (enter user code, display flashes)
Enter the user code using arrow keys e.g. 0001 (basic setting, or the valid code in
case it has been previously changed in this
menu).
Value is shown in both displays.
Automatically forward after 2 sec
Display 1 shows 1 (actual address)
(entry of chamber address)
Display 2 shows Adress 1
(actual address: 1)
Press several times key until Prog.Clk appears:

Display 1 shows 0000

(Week program timer active or inactive?
Display 2 shows Prog.Clk Inactive
(actual setting: Inactive)
Select “Active” using arrow keys Setting is shown in display 2.

Press key
Display 1 shows 0000
(Display mode 12 hours or 24 hours?
Display 2 shows 12h/24h 24h
(actual setting: 24h)
Press key

Display 1 shows 0000

Display 2 shows Date (Main menu: Setting the date of the real time clock)
Press program key

VD (E2.1) 09/2018 page 30/95

 Display 1 shows e.g. 2006 (Actual setting: 2006)
Display 2 shows Year 2006 (Setting the year of the real time clock)
Set year (2006 up to 2050) using arrow keys Setting is shown in display 2.

Press key

Display 1 shows e.g. 5 (Actual setting: may)

Display 2 shows Month 5 (Setting the month of the real time clock)
Set month (1 up to 12) using arrow keys Setting is shown in display 2.

Press key
Display 1 shows e.g. 15 (Actual setting: 15)
Display 2 shows Day 15 (Setting the day of the real time clock)
Set day (1 up to 31) using arrow keys Setting is shown in display 2.

Press key EXIT

Press key

Display 1 shows 0000

Display 2 shows Time (Main menu: Setting the time of the real time clock)
Press program key
Display 1 shows e.g. 13 (Actual setting: 13, i.e. 1 p.m.)
Display 2 shows Hour 13 (Setting the hour of the real time clock)
Set hour (0 up to 23) using arrow keys Setting is shown in display 2.

Press key

Display 1 shows e.g. 30 (Actual setting: 30 minutes)

Display 2 shows Minute 30 (Setting the minute of the real time clock)
Set minute(0 up to 59) using arrow keys Setting is shown in display 2.

Press several times key EXIT or wait for 120 seconds

Controller returns to normal display.

2. Enter the set-points for the week program in Fixed value entry mode (see chap. 6)
Set-points for the example program:
SP1 (night / weekend) = 30 °C (Channel 1 ON = Controller adjusts to set-point SP2)
SP2 (day / week) = 80 °C (Channel 1 OFF = Controller adjusts to set-point SP1)
Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
(actual date and time, actual switching state of week
Display 2 shows e.g. 15.05.06 13:52 - -
program timer channel 1: Off, channel 2: Off)
Press key
C
Display 1 shows 30.0 (actual temperature set-point 1)
Display 2 shows SP1 TEMPERATURE (variable: temperature in °C)
Enter temperature set-point 30 °C using Value is shown in display 1.
arrow keys

VD (E2.1) 09/2018 page 31/95

 Press key
C
Display 1 shows 80.0 (actual temperature set-point 2)
Display 2 shows SP2 TEMPERATURE (variable: temperature in °C)
Enter temperature set-point 80 °C using Value is shown in display 1.
arrow keys
Press the EXIT button. The controller changes to Normal Display.

3. Enter the time program to the week program editor

Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
(actual date and time, actual state of week program timer
Display 2 shows e.g. 15.05.06 13:52 - -
channel 1: Off, channel 2: Off)
Press down key for 5 sec
Display 1 shows e.g. 0000
Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press down key for 5 sec

Display 1 shows 0000

Display 2 shows WEEK PROG. EDITOR (you are in the week program editor)
Press program key

Display 1 shows 0000

Display 2 shows UserCod? 0000 (enter user code, display flashes)
Enter the user code using arrow keys e.g. 0001 (basic setting, adjustable in the
user level, chap. 10).
Value is shown in both displays.
Automatically forward after 2 sec
Display 1 shows 0000
(selection of day of the week)
Display 2 shows Monday
(actual selection: Monday)
Select the first day of the week (Monday) Day of the week is shown in display 2.
with key
Press program key

Display 1 shows 0000

Display 2 shows Shiftpt. (no function)
Press program key
Display 1 shows 0000
(selection of the shift point)
Display 2 shows Shiftpt. 1
(actual shift point: 1)
Select shift point 1 with key Value is shown in display 2.

Press program key

Display 1 shows e.g. --.-- (time of the selected shift point)
(actual selection of the shift point: S1)
Display 2 shows S1: --:--
(actual setting: shift point not programmed)
Press program key

VD (E2.1) 09/2018 page 32/95

Display 1 shows 06.00 (time of the selected shift point)
(entry of time of the selected shift point)
Display 2 shows Time 06:00
(actual setting: 6.00, i.e. 6 a.m.)
Enter the time 06:00 using arrow keys Value is shown in display 2.

Press key
Display 1 shows 0000
(entry of state of channel 1)
Display 2 shows Ch1 = SP2: On
(actual setting: On)
Enter the state of channel 1 Setting is shown in display 2.
On using arrow keys
Press key EXIT
Display 1 shows 06.00 (time of the selected shift point)
(actual selection of the shift point: S1)
Display 2 shows S1: 06:00 � -
(actual setting: time 06.00, channel 1 ON)
Press program key to select the next shift point

Display 1 shows 0000

Display 2 shows Shiftpt. (no function)
Press program key

Display 1 shows 0000

(selection of the shift point)
Display 2 shows Shiftpt. 2
(actual shift point: 2)
Select shift point 2 with key Value is shown in display 2.

Press program key

Display 1 shows e.g. --.-- (time of the selected shift point)
(actual selection of the shift point: S2)
Display 2 shows S2: --:--
(actual setting: shift point not programmed)
Press program key
Display 1 shows 18.00 (time of the selected shift point)
(entry of time of the selected shift point)
Display 2 shows Time 18:00
(actual setting: 18.00, i.e. 6 p.m.)
Enter the time 18:00 using arrow keys Value is shown in display 2.

Press key
Display 1 shows 0000
(entry of state of channel 1)
Display 2 shows Ch1 = SP2: Off
(actual setting: Off)
Enter the state of channel 1 Setting is shown in display 2.
Off using arrow keys
Press key EXIT
Display 1 shows 18.00 (time of the selected shift point)
(actual selection of the shift point: S2)
Display 2 shows S2: 18:00 - -
(actual setting: time 18.00, channel 1 OFF)
Press key EXIT twice to select the next day of the week

VD (E2.1) 09/2018 page 33/95

 Display 1 shows 0000
(selection of day of the week)
Display 2 shows Tuesday
(actual selection: Tuesday)
Select the next day of the week (Tuesday) Day of the week is shown in display 2.
with key

Press program key

Display 1 shows 0000

Display 2 shows Shiftpt. (no function)
Press program key

Display 1 shows 0000

(selection of the shift point)
Display 2 shows Shiftpt. 1
(actual shift point: 1)
Select shift point 1 with key Value is shown in display 2.

Press program key

Display 1 shows e.g. --.-- (time of the selected shift point)

(actual selection of the shift point: S1)
Display 2 shows S1: --:--
(actual setting: shift point not programmed)
Press program key

Display 1 shows 06.00 (time of the selected shift point)

(entry of time of the selected shift point)
Display 2 shows Time 06:00
(actual setting: 6.00, i.e. 6 a.m.)
Enter the time 06:00 using arrow keys Value is shown in display 2.

Press key

Display 1 shows 0000

(entry of state of channel 1)
Display 2 shows Ch1 = SP2: On
(actual setting: ON)
Enter the state of channel 1 Setting is shown in display 2.
On using arrow keys

Press key EXIT

Display 1 shows 06.00 (time of the selected shift point)

(actual selection of the shift point: S1)
Display 2 shows S1: 06:00 � -
(actual setting: time 06.00, channel 1 ON)
Press program key to select the next shift point

etc.
Following entry of the complete program:

Press several times key EXIT or wait for 120 seconds

Controller returns to normal display.

VD (E2.1) 09/2018 page 34/95

8. Program editor

8.1 Selecting between set-point ramp and set-point step

You can program various kinds of temperature transitions. In the user level (chap. 10) you can select
between the settings “Ramp” (default setting) and “Step”.

Setting “Ramp” permits programming all kinds of temperature transitions.

With setting “Step” the controller will equilibrate only to constant temperatures; programming
ramps is no longer possible.

Switching between settings “Ramp” and “Step” will influence all programs. Please note that this
can cause the time courses of existing programs to change significantly.

8.1.1 Programming with setting “Ramp” (default setting)

Set-points always refer to the start of a program section, i.e., at the beginning of each program section,
the entered set-point is reached. During program section operation, the temperature gradually passes to
the set-point entered for the subsequent program section.
You can program all kinds of temperature transitions by the appropriate design of the program section
timing:
• Gradual temperature changes “set-point ramp“
The set-point gradually moves from one set-point to the one of the following program section during a
given interval. The actual temperature value (X) follows the continually moving set-point (W) at any
moment.
• Program sections with constant temperature
The initial values of two subsequent program sections are identical; therefore the temperature remains
constant during the whole time of the first program section.
• Sudden temperature changes “set-point step”
Steps are temperature changes (ramps) that occur during a very short interval. Two program sections
with an identical set-point are followed by a section with a different set-point. If the duration of this
transitional program section is very short (minimum entry 1 min), the temperature change will proceed
rapidly in the minimum amount of time.

05 07
01 02 03 04 06 08 09

t
Figure 9: Possible temperature transitions
(with default setting “ramp” in the user level (chap. 10)

VD (E2.1) 09/2018 page 35/95

Program entry as set-point ramp (example):

S01 S02 S03 S04 S05

W/°C

100

80

60

40

20

0
30 120 180 380 t/min.

Program table corresponding to the diagram (with default setting “Ramp”):

Section Temperature Section length Operation lines
set-point [hh.mm]
[ °C]
SEC TEMP TIME O.LINE
S01 40 00:30 000
S02 60 01:30 000
S03 90 01:00 000
S04 90 03:20 000
S05 20 00:01 000
You can now enter the values of such a program table to the RD3 program controller (chap. 8.2).

Program entry as set-point step (example):

S01 S02 S03 S04 S05 S06 S07 S08

W/°C

100

80

60

40

20

0
30 120 180 380 t/min.

VD (E2.1) 09/2018 page 36/95

Program table corresponding to the diagram (with default setting “Ramp”):
Section Temperature Section length Operation lines
set-point [hh.mm]
[ °C]
SEC TEMP TIME O.LINE
S01 40 00:30 000
S02 40 00:01 000
S03 60 01:30 000
S04 60 00:01 000
S05 80 01:00 000
S06 80 00:01 000
S07 20 03:20 000
S08 20 00:01 000
You can now enter the values of such a program table to the RD3 program controller (chap. 8.2).
Program the end point of the desired cycle with an additional section (in our examples S05 for set-point
ramp and S08 for set-point step) with a section time of at least one minute. Otherwise, the program will
stop one section too early because the program line is incomplete.

8.1.2 Programming with setting “step”

With setting “Step” selected, you don’t need to program the transition section in the Program Editor.

With setting “step” the controller will equilibrate only to constant temperatures; programming
ramps is no longer possible.
The set-points are maintained constant for the duration of a program section. At the start of each program
section, the chamber heats up with the maximum speed in order to attain the entered set-point

Program entry as set-point step (example):

S01 S03 S05 S07

W/°C

100

80

60

40

20

0
30 120 180 380 t/min.

VD (E2.1) 09/2018 page 37/95

Program table corresponding to the diagram (with setting “Step”):
Section Temperature Section length Operation lines
set-point [hh.mm]
[ °C]
SEC TEMP TIME O.LINE
S01 40 00:30 000
S02 60 01:30 000
S03 80 01:00 000
S04 20 03:20 000
You can now enter the values of such a program table to the RD3 program controller (chap. 8.2).

8.1.3 General notes on programming temperature transitions

When exceeding the tolerance limits set in the user level (chap. 10), the program is interrupted until the
actual temperature value returns to within the tolerance range. During this program interruption, the LED
(7d) flashes. Therefore, the duration of the program may be extended due to the programming of
tolerances
The programming is saved even in case of power failure or after turning off the chamber.
After program rundown the controller returns to fixed value operation showing Normal Display and
equilibrates to the temperature value previously entered in fixed value entry mode.

Before starting the program, check the set-point value entered in fixed value entry mode. After
program rundown temperature will equilibrate to this value.

Deactivate the week program timer (factory setting, setting in the user level, chap. 10) before
starting a program.

8.2 Set-point entry for program operation

From Normal Display, press down button X/W for 5 sec to access the program editor. Then enter the set-
points one after the other in all program sections of a selected program.
You can enter two programs with up to 10 sections each or one program with up to 20 sections (setting in
the user level, chap. 10).
In order to avoid incorrect programming, we recommend entering the values of the program course into a
table (template in chap. 8.3).
Example of program table (with default setting “Ramp”):
Section Temperature set-point Section length Operation lines
[ °C] [hh.mm]

SEC TEMP TIME O.LINE

S01 40 00:30 000
S02 60 01:30 000
S03 90 01:00 000
S04 90 03:20 000
S05 20 00:01 000
You can now enter the values of the program table to one of the program places of the RD3 program
controller.

VD (E2.1) 09/2018 page 38/95

Step 1 – Selecting the program and the first program section to be entered:
Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
(actual date and time, actual switching state of week
Display 2 shows e.g. 15.05.06 13:52 - -
program timer channel 1: Off, channel 2: Off)
Press down key for 5 sec.

Display 1 shows e.g. 0000

Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press program key

Display 1 shows 0000

Display 2 shows UserCod? 0000 (enter user code)
Enter user code using arrow keys e.g. 0001
(basic setting, adjustable in the user level,
chap. 10).
Value is shown in both displays.

Automatically forward after 2 sec.

Display 1 shows e.g. 01 (program P01 selected)

Display 2 shows --- : --- PRG. (program can be selected)
st
alternating CONTINUE X/W (information: to 1 program section with X/W)
Select program P01 or P02 using arrow keys Value is shown in display 1.

Press key

In the selected program P01 or P02, program sections can be selected:

Display 1 shows e.g. 01 (section S01 selected)
Display 2 shows P01: --- SEC. Section S01 has already been created.
Enter new set-points for the individual variables with button
alternating CONTINUE X/W X/W
or:
Display 1 shows e.g. 01 (section S01 selected)
Display 2 shows P01: --- SEC. Section S01 has not yet been created.
alternating Enter set-points for the individual variables with button X/W
NEW SEC. X/W

Select sections S01 to S10 or to S20 using

arrow keys

As long as no program section has been entered, the display switches back to 01 in case of any entry
> 01, because all sections need to be entered one after the other, and each new section is created as
NEWSEC.

Example: If three programs sections have been already entered, the next section to be entered is S04.
Before this, no section > S04 can be selected.

VD (E2.1) 09/2018 page 39/95

Next step – set-point entry in the desired program sections:
Basic entry principle: Access the parameters of individual program sections with button X/W one after
the other. Enter the values of the individual parameters with the arrow keys. A value flashing once after 2
seconds indicates that it has been adopted by the controller. If several parameters are to be skipped (e.g.
in order to change a parameter in a posterior program section), the parameters can be rapidly jumped
over by holding down the X/W key. If no button is pressed for more than 120 sec the controller switches
back to Normal Display. The program entered to this point remains stored.

Press key
C
Display 1 shows e.g. 40.0 (actual temperature set-point)
Display 2 shows S01: TEMP 40.0 (variable: temperature in °C)
alternating CONTINUE X/W (information: go on with X/W)
Enter temperature set-point of S01 in °C
using arrow keys
Press key
Display 1 shows e.g. 00.30 (actual section length set-point)
Display 2 shows S01: TIME 00:30 (variable: section length in hh:mm)
alternating CONTINUE X/W (information: go on with X/W)
Enter section length set-point of S01 in Value is shown in both displays.
hh.mm using arrow keys
Press key

Display 1 shows e.g. 000 (actually set switching state)

Display 2 shows S01:O.LINE 000 (variable: switching state)
alternating CONTINUE X/W (Information: go on with X/W)
Enter switching state of operation lines using (see chap. 15, switching outputs via operation
arrow keys lines)
Press key

Selecting the next program sections to be entered

Display 1 shows e.g. 02 (section S02 selected)
Display 2 shows P01: --- SEC. Section S02 has already been created.
alternating CONTINUE X/W Enter new set-points for the individual parameters with X/W.
or:
Display 1 shows e.g. 02 (section S02 selected)
Display 2 shows P01: --- SEC. Section S02 has not yet been created.
alternating Enter set-points for the individual parameters with X/W
NEW SEC. X/W
Select the next section to be entered using
arrow keys
C
Display 1 shows e.g. 60.0 (actual temperature set-point)
Display 2 shows S02:TEMP 60.0 (variable: temperature in °C)
alternating CONTINUE X/W (information: go on with X/W)
Enter the temperature set-point of S02 in °C
using arrow keys
Etc.
If all sections up to S10 or up to S20 have been programmed, section S01 follows again. In order to quit
the entry mode, press the EXIT button several times or wait 120 sec → the controller will then return to
Normal Display.

When changing the set-point, check the setting of the safety device (chap. 12).

VD (E2.1) 09/2018 page 40/95

8.3 Program table template

Program editor

Program title

Project

Program No.

Date:

Section Temperature set-point Section length Operation lines *

[ °C] [hh.mm]

SEC TEMP TIME O.LINE

S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20

* Switching contacts 24V DC via operation lines, see chap. 15.

VD (E2.1) 09/2018 page 41/95

8.4 Deleting a program section
A program section is deleted from the program by setting the section duration to Zero.
Normal display

Press down key for 5 sec.

Display 1 shows e.g. 0000

Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press program key

Display 1 shows 0000

Display 2 shows UserCod? 0000 (enter user code)
Enter the user code using arrow keys e.g. 0001 (basic setting, adjustable in the user
level, chap. 10).
Value is shown in both displays.

Automatically forward after 2 sec

Display 1 shows e.g. 01 (program P01 selected)
Display 2 shows --- : --- PRG. (program can be selected)
st
alternating CONTINUE X/W (information: to 1 program section with X/W)
Select the desired program, e.g. P01, using Value is shown in display1.
arrow keys
Press key

In the selected program P01 or P02, program sections can be selected:

Display 1 shows e.g. 01 (actual selection of the section: S01)
Display 2 shows P01: --- SEC. (program section can be selected)
alternating CONTINUE X/W (information: set-point entry with X/W)
Select desired section, e.g. S03, using arrow (omitted if section S01 shall be deleted).
keys
Press key
C
Display 1 shows e.g. 90.0 (actual temperature set-point)
Display 2 shows S03:TEMP 90.0 (variable: temperature)
alternating CONTINUE X/W (information: continue with X/W)
No entry

Press key

Display 1 shows e.g. 01.00 (actual section length)

Display 2 shows S03:TIME 01:00 (variable: section length)
alternating CONTINUE X/W (information: continue with X/W)
Enter set-point Zero for section length in Value is shown in display 2 or in both displays
hh:mm of S03 using arrow keys (display depends on maximum time setting in
the user level chap. 10)
Display 1 shows e.g. 00.00 (actual section length)
Display 2 shows S03:TIME 00:00 (variable: section length)
alternating DELETE SEC. X/W (information: delete section with X/W)
Press key

VD (E2.1) 09/2018 page 42/95

 The following section (in our example now S03) is displayed:
Display 1 shows e.g. 03 (actual selection of the section: S03)
Display 2 shows P01:S03 (program section can be selected)
alternating CONTINUE X/W (information: set-point entry with X/W)
Press key EXIT or wait 120 sec

Controller returns to Normal Display

If you delete a program section which is followed by further sections, those following move up
in place of the deleted section.

In our example, section S03 has been deleted. If sections S04, S05, etc. have been programmed earlier,
they will now replace the preceding sections, i.e., S04 is now called S03 etc.
Deletion leads to overwriting the section by the following one. It is therefore not possible to temporarily
inactivate a program section. To enter a section later to a program, all the sections following the new one
must be entered again.

9. Program start level

Before starting the program, check the set-point entered in Fixed value operation mode. After end of the
program, the temperature will equilibrate to this value.

CAUTION
Too high or too low temperature after the program ends.
Damage to the charging material.
 Check the set-point of Fixed value operation and if necessary adapt it.

After the program ends, the temperature will equilibrate to the set-point entered in Fixed value operation
mode. If the week program timer is active, another set-point (SP2) may be targeted according to
programming. Deactivate the week program timer before starting the program (default setting, setting in
the User level, chap. 10).

CAUTION
Too high or too low temperature after the program ends.
Damage to the charging material.
 Deactivate the week program timer before starting the program.

In the first step, select a program. This is on condition that a program has been entered previously (chap.
8.2) and that program type “2 programs with 10 sections each” has been selected in the user level (chap.
10).
Then define the settings for the program course. Two parameters can be set:
• Program delay time, i.e. a defined time before a program starts. It can be entered with a precision of 1
minute, and its maximum value is 99.59 (99 h 59 min). If the value is 00.00, the program will start
immediately.
• Number of program cycles, i.e. the desired number of program repeats. Values from 1 to 99 can be
entered. If the program is not going to be repeated, enter the value “0”. For indefinite repeats enter the
value “–1”. The program is repeated as a whole, it is not possible to repeat individual sections.
In the last step start the selected program. These steps must be carried out subsequently.

VD (E2.1) 09/2018 page 43/95

 Deactivate the week program timer (factory setting, setting in the user level, chap. 10) before
starting a program.

Step 1 – Program selection (only with program type “2 programs” set)

Normal Display

Press program key

Display 1 shows e.g. 1 (actual selection of the program)

Display 2 shows SEL.PRG. (select program 1 or 2)
Enter program number 1 or 2 with Value is shown in display 1.
arrow keys

Next step – entry of program course settings

Press program key

Display 1 shows e.g. 00.00 (entered delay time hh.mm)

Display 2 shows RUN TIME (enter delay time of program start)
Set delay time in hh.mm using arrow keys Value is shown in display 1.

Press program key

Display 1 shows e.g. -1 (actual selection of the number of program cycles)

Display 2 shows REPEAT (enter number of program cycles)
Select number of cycles -1, 0, 1 etc. using Value is shown in display 1.
arrow keys

Last step – program start

Press program key

Display 1 shows e.g. 1 (selected program)

Display 2 shows RUN PRG. (Question: start selected program?)
Press program key
C
Display 1 shows e.g. 25.5 actual temperature value
P01:S01 00:29:39 (actual program P01, actual section S01, and remaining
Display 2 shows
(time running backwards) time of program section S01)

Program is running. The green LED (7d) lights up.

In addition to the green LED (7d) indicating a running program, the LED (7a) is lit if the heating is active, or
not lit if the actual temperature equals the set-point.

During program course the arrow keys and the EXIT button are not functional.

By pressing program key for 3 seconds, you can terminate the program course.

VD (E2.1) 09/2018 page 44/95

If you press button during program course, the entered set-point of the actually running program
section is shown for 5 sec:
C
Display 1 shows e.g. 65.5 (actual temperature value)
(actual program P01, actual section S03, and remaining time
Display 2 shows P01:S03 00:47:12
of program section S03)
Press key
C
Display 1 shows e.g. 90 (actual temperature set-point 1)
Display 2 shows SP1 TEMPERATURE
5 seconds
C
Display 1 shows e.g. 30 (actual temperature set-point 2)
Display 2 shows SP2 TEMPERATURE (no function during program operation)
5 seconds

Display 1 shows e.g. 000 (actual operation line setting)

Display 2 shows OPERATION LINE

After program rundown (and, if appropriate, of the program repeats) the controller returns to fixed value
operation showing Normal Display and equilibrates to the temperature value previously entered in fixed
value entry mode.

VD (E2.1) 09/2018 page 45/95

10. User level
In this menu you can set the following parameters (in brackets the corresponding abbreviated information
given in display 2):
• Chamber address (Adress)
Setting of controller address (1 to 255) for operation with the communication software APT-COM™.
• User code (User-cod)
Modification of the user code setting (factory setting 0001) for access to the user level and the program
editor.

Keep in mind any modification of the user code. There is no access to these levels
without a valid user code.

• Decimal point position (Decimal)

Selection if integer values or one position after the decimal point can be entered. The integer
representation is shown in Display 2 (set-point entry) while the actual value in Display 1 is always
shown with one decimal point.
• Audio Alert (Buzzer)
Inactive: no audible signal (buzzer) in case of an alarm event.
Active: in case of an alarm event (see chap. 11.2) an audible signal (buzzer) will sound. It can be reset
by pressing the EXIT button.
• Selection of controller menu language (Language)
German, English, or French can be selected.
• Counter of operating hours (Oper.hs)
Information about the number of operating hours currently reached or since the last reset (no setting,
display only).
• Max. number of operating hours (Op.limit)
Entry of a limit number of operating hours, i.e., the maximum number of operating hours that can be
run. Maximum setting: 9999. Reaching the limit has no effect.
• Reset operating hours (Op.back)
Reset operating hours to zero.
• Interface protocol (Protocol)
“Modbus”: The chamber interface can be used as a communication interface to connect it to a
computer. This serves to control the chamber by the communication software APT-COM™. It is
possible to read and write the values of all parameters.
“Printer”: A protocol printer for data printouts can be connected to the chamber interface. At the printer
the actual temperature value is regularly protocolled with fixed formatting and with adjustable print
intervals.
In both cases an interface converter RS 422 / RS 232 is used.
• Print interval (Prt.-Inv.)
Setting of the print interval in minutes. Function is available only if setting “Printer” has been selected in
the previous menu point.
• Display illumination (Disp.LED)
Selection between continuous display illumination and limited illumination that will automatically go off
300 sec after the last entry.

VD (E2.1) 09/2018 page 46/95

• Program type selection (PrgSelec)
Select between entry of two programs with up to 10 sections each or of one program with up to 20
sections.

When changing from 2 programs to 1 program or vice-versa, existing programs are

deleted in the program editor!

• Maximum section duration (Prg.Time)

The maximum length of an individual program section can be set to either 99 h 59 min or to 999 h 59
min. This setting is then valid for all program sections.

When changing the maximum duration setting, pre-existing programs will be deleted in
the program editor.

• Set-point programming type (Setp.sim)

Selection between “Ramp” and “Step”. With setting „Step“ selected, you don’t need to program the
transition section in the Program Editor.

If you select setting “step”, the controller will equilibrate only to constant temperatures;
programming ramps becomes impossible.

A change between settings “ramp” and “step” will influence all programs. Note that
significant change in time courses may arise in existing programs.

• Tolerance limit range (Tol.band)

Entry of a tolerance limit value in °C. If the actual value of temperature exceeds the set-point of a
program section by more than the entered tolerance limit value, the program is halted (LED (7d)
flashes) until the actual temperature value is again within in the tolerance range
Entry of “0” means tolerance limits are off.
• Activating or inactivating the week program timer (Prog.Clk)
“Inactive”: The week program timer is turned off (factory setting). The corresponding setting menu
(chap. 7) is not visible, nor is is set-point 2 in the “Fixed value entry mode” (chap. 6).
“Active”: The week program timer is activated.

When deactivating the week program timer, any programming made in advance will
remain in memory and take effect when the week program timer is activated again.

Deactivate the week program timer before entering set-points in fixed value entry mode
(chap. 6). Otherwise, any setting of the operation lines is ineffective.

Inactivate the week program timer before staring a program (chap. 9).

• Display mode (12h/24h)

Select between 12 hours (display “AM” or “PM”) or 24 hours.
• Date of the real time clock (Date)
Main menu. Use the program key to access the settings of year, month, and day in the corresponding
submenus.
• Year of the real time clock (Year)
Enter the year (2006 up to 2050)

VD (E2.1) 09/2018 page 47/95

 • Month of the real time clock (Month)
Enter the month (1 up to 12).
• Day of the real time clock (Day)
Enter the day (1 up to 31).
• Time of the real time clock (Time)
Main menu. Use the program key to access the settings of hour and minute in the corresponding
submenus.

There is no automatic switch between daylight saving time and regular time.

• Hour of the real time clock (Hour)

Enter the hour (0 up to 23).
• Minute of the real time clock (Minute)
Enter the minute (0 up to 59).

Normal Display
C
Display 1 shows e.g. 39.8 (actual temperature value)
(actual date and time, actual switching state of week
Display 2 shows e.g. 15.05.06 13:52 - -
program timer channel 1: Off, channel 2: Off)
Press down key for 5 sec

Display 1 shows e.g. 0000

Display 2 shows PROGRAM EDITOR (you are in the program editor)
Press down key for 5 sec

Display 1 shows 0000 Menu visible only if week program timer is activated.
Display 2 shows WEEK PROG. EDITOR (you are in the week program editor)
Press down key for 5 sec

Display 1 shows 0000

Display 2 shows USER – LEVEL (you are in the user level)
Press program key

Display 1 shows 0000

Display 2 shows UserCod? 0000 (enter user code, display flashes)
Enter the user code using arrow keys e.g. 0001 (basic setting,
or the valid code in case it has been previously
changed in this menu).
Value is shown in both displays.
Automatically forward after 2 sec
Display 1 shows 1 (actual address: 1)
(entry of chamber address)
Display 2 shows Adress 1
(actual address: 1)
Enter the chamber address (1 up to 254) Address is shown in both displays.
using arrow keys

Press key

VD (E2.1) 09/2018 page 48/95

Display 1 shows 1 (actually valid user code: 1)
(change user code)
Display 2 shows User-cod 1
(actually set: 1)
Enter a new value using arrow keys Value is shown in both displays.

Press key
Display 1 shows 0000 (no function)
Display 2 shows Saf.mode: Limit (no function)
Press key
Display 1 shows 0 (no function)
Display 2 shows Saf.setp 0 (no function)
Press key
Display 1 shows 0000 (no function)
(setting of decimal point position)
Display 2 shows Decimal: XXX.X
(actual setting: XXX.X)
Select decimal point position using arrow Decimal point position XXX.X or XXXX. is
keys shown in display 2.
Press key
Display 1 shows 0000 (no function)
Display 2 shows (setting of the alarm buzzer)
Buzzer : Active
(actual setting: „Active“)
Select between “Active” and “Inactiv” using Setting is shown in display 2.
arrow keys
Press key
Display 1 shows 0000 (no function)
(selection of controller language)
Display 2 shows Language : English
(actual setting: English)
Select between languages German, English, Setting is shown in display 2.
and French using arrow keys
Press key

Display 1 shows e.g. 0004 (chamber operating hours)

(operating hours up to now hhhh:mm)
Display 2 shows Oper.hs 0004:28
(actually displayed: 4 hs 28 min)
Press key
Display 1 shows 1000 (actual setting: 1000 hs)
1000:00 (maximum number of operating hours
Display 2 shows Op.limit
hhhh:mm (actual setting: 1000 hs)
Set value using arrow keys Setting is shown in both displays.

Press key
Display 1 shows 0000 (no function)
(reset counter of operating hours ?)
Display 2 shows Op.back : No
(actual setting: No)
Select between “Yes” and “No” using arrow Setting is shown in display 2.
keys

VD (E2.1) 09/2018 page 49/95

 Press key
Display 1 shows 0000 (no function)
(Selection of interface mode)
Display 2 shows Protocol: MODBUS
(actual setting: Modbus)
Select between protocols “MODBUS” and Setting is shown in display 2.
“Printer” using arrow keys
Press key
Display 1 shows e.g. 3 (actual setting: 3 min)
(print interval)
Display 2 shows Prt-Inv. 3
(actual setting: 3 min)
Select value between 0 and 255 minutes Setting is shown in displays 1 and 2.
using arrow keys
Press key
Display 1 shows 0000
(continuous display illumination?)
Display 2 shows Disp.LED: No
(actual setting: No)
Select between “Yes” and “No” using arrow Setting is shown in display 2.
keys
Press key

Display 1 shows 0000

(1 program with max. 20 sections or
Display 2 shows PrgSelec: 2Prg10S 2 programs with max. 10 sections each?)
(actual setting: 2Prg10S)
Select between “2Prg10S” and “1Prg20S” Setting is shown in display 2.
using arrow keys
Press key
Display 1 shows 0000
(max. section length 99:59 or 999:59?)
Display 2 shows Prg.Time: 99:59
(actual setting: 99:59)
Select between 99:59 in hh:mm or 999:59 in Setting is shown in display 2.
hhh:mm using arrow keys
Press key
Display 1 shows 0000
(ramp or step?)
Display 2 shows Setp.sim Ramp
(actual setting: ramp)
Select between Ramp and Step using arrow Setting is displayed in display 2.
keys
Press key

Display 1 shows 0000

(Tolerance limits in °C)
Display 2 shows Tol.band 0
(actual setting: 0)
Set value in °C using arrow keys Setting is shown in display 2.

Press key
Display 1 shows 0000
(Week program timer active or inactive?
Display 2 shows Prog.Clk Inactive
(actual setting: Inactive)

VD (E2.1) 09/2018 page 50/95

Select between “Active” and “Inactive” using Setting is shown in display 2.
arrow keys

Press key
Display 1 shows 0000
(Display mode 12 hours or 24 hours?
Display 2 shows 12h/24h 24h
(actual setting: 24h)
Select between 12 hours and 24 hours Setting is shown in display 2.
using arrow keys

Press key
Display 1 shows 0000
Display 2 shows Date (Main menu: Setting the date of the real time clock)

Press program key

Display 1 shows e.g. 2006 (Actual setting: 2006)
Display 2 shows Year 2006 (Setting the year of the real time clock)
Set year (2006 up to 2050) using arrow keys Setting is shown in display 2.

Press key

Display 1 shows e.g. 5 (Actual setting: may)

Display 2 shows Month 5 (Setting the month of the real time clock)
Set month (1 up to 12) using arrow keys Setting is shown in display 2.

Press key
Display 1 shows e.g. 15 (Actual setting: 15)
Display 2 shows Day 15 (Setting the day of the real time clock)
Set day (1 up to 31) using arrow keys Setting is shown in display 2.

Press key EXIT

Press key

Display 1 shows 0000

Display 2 shows Time (Main menu: Setting the time of the real time clock)
Press program key

Display 1 shows e.g. 13 (Actual setting: 13, i.e. 1 p.m.)

Display 2 shows Hour 13 (Setting the hour of the real time clock)
Set hour (0 up to 23) using arrow keys Setting is shown in display 2.

Press key

Display 1 shows e.g. 30 (Actual setting: 30 minutes)

Display 2 shows Minute 30 (Setting the minute of the real time clock)
Set minute(0 up to 59) using arrow keys Setting is shown in display 2.

Press several times key EXIT or wait for 120 seconds

Controller returns to normal display.

VD (E2.1) 09/2018 page 51/95

11. Performance in case of failures

11.1 Performance after power failure

Power failure during fixed-value operation (Normal Display):

The entered parameters remain saved. After power returns operation continues with the set parameters.
Power failure during program operation:
After the power returns, program course continues with the set-points that have been reached previously
during program operation.

11.2 Alarm messages

Alarm messages, e g. “RANGE ERROR CH1” in case of sensor rupture, are shown in Display 2 only in
Normal Display.
A buzzer can be activated / deactivated in the user level (chap. 10). It can be reset by pressing the EXIT
button. The alarm text shown in Normal Display goes off only if the cause of the alarm does not exist any
longer.

12. Temperature safety device class 2

The chamber is equipped with a temperature safety device class 2 (temperature limiter) acc. to DIN
12880:2007. The safety device protects the vacuum drying oven, its environment and the charging
material from exceeding the maximum permissible temperature.
Please observe the DGUV guidelines 213-850 on safe working in laboratories (formerly BGI/GUV-I 850-0,
BGR/GUV-R 120 or ZH 1/119, issued by the employers’ liability insurance association) (for Germany).

The temperature safety device only activates after the set-point has been reached once.

In the event of a fault in the temperature controller, the safety device (2) permanently turns off the
vacuum drying oven. This status is reported visually by the indicator lamp (2a).
Check the operation of the safety device (2) by moving it slowly counter-clockwise until it is turned off. The
safety device cut-off is reported visually by the indicator lamp (2a).
Then release the safety device by pressing the reset button (2b), and turn on the VD vacuum drying oven
as described previously.

(2b)

(2)

(2a)

Figure 10: Temperature safety device class 2

VD (E2.1) 09/2018 page 52/95

Function:
The safety device is functionally and electrically independent of the temperature control device and turns
off the chamber at all poles.
If you turn the control knob (2) to its end-stop (position 10), the safety device will protect the appliance. If
you set it to a temperature a little above the set-point temperature, it will protect the charging material.
If the safety device has turned off the oven, identifiable by the red alarm lamp (2a) lighting up, proceed as
follows:
• Disconnect the oven from the power supply
• Have an expert examine and rectify the cause of the fault
• Release the safety device by pressing the reset button (2b)
• Restart the oven as described in chap. 4.4.

Adjustment:
To check the response temperature of the safety device, turn on the chamber and set the desired set
point on the temperature controller.
The scale division from 1 to 10 corresponds to the temperature range from 30° / 86°F up to 320 °C /
608°F and serves as a setting aid.
• Turn the control knob (2) of the safety device using a coin to its
end-stop (position 10) (chamber protection).
• When the set point is reached, turn back the control knob (2) until
its trip point (turn it counter-clockwise) is reached.
• The red alarm lamp (2a) lighting up identifies the trip point; and the
reset button (2b) pops out.
• The optimum setting of the safety device is obtained by turning the
knob clockwise by approx. one graduation mark on the scale.
• Push the reset button (2b) in again. Figure 11: Setting the safety
device class 2

The chamber is only active when the reset button (2b) is pushed in.

When the safety device responds, the red alarm lamp (2a) illuminates, the reset button (2b) pops out, and
the oven is turned off permanently at all poles.

Check the setting regularly and adjust it following changes of the set-point or charge.

Function check:
Check the temperature safety device class 2 at appropriate intervals for its functionality. It is
recommended that the authorized operating personnel should perform such a check, e.g., before starting
a longer work procedure.

VD (E2.1) 09/2018 page 53/95

13. Reference measurements. Checking the temperature in the inner
chamber
The controller display was adjusted in the factory to the temperature in the center of the usable volume
(chap. 20.1). The sensor probe of the reference measuring device was connected tightly to an expansion
rack positioned in the middle of the chamber.

Checking the controller display

• Conduct the reference sensor into the inner chamber through the measuring port (17). The port must
be largely vacuum tight to enable a typical operation vacuum for the calibration. For a high vacuum,
use a measuring access port. Usually, a silicone plug with a hole for the sensor wire is sufficient.
• Fix the sensor to the center of an expansion rack in the middle of the useable volume with adhesive
aluminum tape or thermal conductive paste to ensure sufficient thermal conductivity.
• Perform the measurement in a thermally stable condition with 3 expansion racks and empty oven.
• Equilibrating time: at least 12 hours.

Checking the spatial temperature exactitude

• Fix at least 9 sensor probes on 3 racks with adhesive aluminum tape or thermal conductive paste to
ensure sufficient thermal conductivity
• The distance of the sensor probes to all inner chamber walls must be at least 10% of the
corresponding inner chamber dimension (see DIN 12880).
• Perform the measurement in a thermally stable condition with 3 expansion racks and empty oven.
• Response time: at least 12 hours.

Do NOT use the temperature probe of the reference measurement device without any contact
to the expansion rack, i.e., do NOT measure vacuum values!

In case the temperature probe is a thermo element, mount it so it is electrically insulated from
the rack.

If you note an excessive divergence between the controller and reference temperatures, please contact
BINDER Service to calibrate the temperature controller.

14. Commissioning the vacuum

With regard to operation, please observe the DGUV guidelines 213-850 on safe working in laboratories
(formerly BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued by the employers’ liability insurance
association) (for Germany).
Starting situation: The vacuum source is connected and ready for operation.
For the vacuum module with chemical membrane pump option, see chap. 16.3 and 16.4.

VD (E2.1) 09/2018 page 54/95

14.1 Evacuation

• VD 23: Close the air/gas valve (4).

• VD 53 and VD 115: Close the aeration valve (5) and the fine dosing valve for inert gas (6).
• Turn on the vacuum pump.
• Put the lever of the vacuum shut off valve (8) to
“ON” position (valve open).
• Monitor the internal pressure on the pressure
display (3). The analog manometer displays the
running evaporation respectively the end of the
drying procedure. The scale of the manometer (3)
refers to an ideal ambient pressure of 1013 mbar /
29.9 inHg. Tolerance: 50 mbar / 37.5 mm Hg
(Torr) / 1.48 inch Hg (2.5% of the final scale value
+ reading precision). The optional digital pressure
display (chap. 16.5) offers an absolute scale.
• When the desired end vacuum is obtained, turn
the VDL vacuum shutoff valve (8) to the “OFF”
position (valve closed). The reached vacuum is
now maintained.

Figure 12: Manometer display

-2
The permissible end vacuum is 10 mbar / 0.0003 inHg.

As long as there is a vacuum, never try to open the oven by force.

14.2 Breaking the vacuum (flooding with ambient air)

When the drying procedure is complete, the vacuum in the inner container is broken (flooded).
VD 23:
• Open air/gas valve (4)
Fresh air is sucked in through the inert gas connection (12)
VD 53, VD 115:
• Open aeration valve (5)
Fresh air is sucked in through the lateral ventilation slots of the instrument box.
• Open fine dosing valve for inert gas (6)
Fresh air is sucked in through the inert gas connection (12)
The fresh air is introduced into the lower part of the rear panel of the inner chamber and is evenly
distributed in the inner chamber. This supply of fresh air by under-flooding prevents turbulence of
pulverized drying material.

VD (E2.1) 09/2018 page 55/95

14.3 Operation with inert gas
When operating the VD vacuum drying oven with inert gas, correctly follow the technical ventilation
measures, as described in the DGUV guidelines 213-850 on safe working in laboratories (formerly
BGI/GUV-I 850-0, BGR/GUV-R 120 or ZH 1/119, issued by the employers’ liability insurance association)
(for Germany).
Inert gases in high concentrations are hazardous to health. They are colorless and almost odorless and
therefore practically imperceptible. Inhalation of inert gases can cause drowsiness up to respiratory arrest.
When the O2 content of the air decreases below 18%, there is risk of death from lack of oxygen. Any gas
that might escape has to be led out via good room ventilation or a suitable exhaust system.

WARNING
High concentration of inert gas.
Risk of death by suffocation.
∅ Do NOT set up chambers in non-ventilated recesses.
 Ensure technical ventilation measures.
 Respect the relevant regulations for handling these gases.
 When decommissioning the vacuum drying oven, shut off the inert gas supply: Close
valves (4) or (6).

Install a pressure reducer for inert gas operation. Set the pressure reducer to a pressure slightly above
ambient pressure. Ensure that the pressure reducer will open. Do not change this setting in order to avoid
perturbation inside the oven and release of big quantities of inert gas after flooding the VD.
Following evacuation, an inert gas, e.g., nitrogen, is led into the inner chamber via the air/gas valve (4)
(VD 23) or the fine dosing valve for inert gas (6) (VD 53, VD 115), until pressure compensation with the
atmosphere occurs. Depending on the individual application, you can perform a second evacuation and
repeat the inert gas flooding.
When the inert gas fine dosing valve is open, a maximum of approx. 0.6 m³/h gas flows into the inner
chamber. The introduction of inert gas by under-flooding in the lower region of the inner chamber rear wall
and the extraction at the inner chamber ceiling allow an effective inert gas flushing.

If the oven is charged to full capacity, depending on the load, deviations from the specified
heating up times may occur.

VD (E2.1) 09/2018 page 56/95

15. Switching contacts 24V DC via operation lines
Operation lines 1 and 2 are used to switch on and off electrical equipment (nominal voltage 24 V DC,
current consumption max. 0.4 A). The switching contacts are connected with two DIN sockets (13) and
(14) at the chamber rear.
The operation lines permit switching on and off the switching contacts by program control. You can
program the operation lines in “Fixed value entry mode” (chap. 6) as well as in the “Program editor” (chap.
8.2) via the operation lines (switching state “0” = Off, switching state “1” = On).
Set the positions “100” or “010” or “110” or “000” as follows:
Operation line 1 Operation line 2 Operation line 3
(no function)
1 0 0 Operation line 1 ON
0 1 0 Operation line 2 ON
1 1 0 Operation lines 1 and 2 ON
0 0 0 Operation line OFF
You can combine any of the switching states of the operation lines. You can recognize switching state ON
when the LED (7b) for operation line 1 and the LED (7c) for operation line 2 light up.

Operation lines 1 and 2 are designed for the following options:

• Operation line 1: Program controlled evacuation (option “vacuum module with pump”, see chap. 16.3)
• Operation line 2: Program controlled venting (option “program controlled venting”, available via
BINDER INDIVIDUAL customized solutions)
You can connect any other device or electrical equipment with a nominal tension of 24 V DC and a current
consumption of max. 0.4 A.
Establish the connection via the DIN sockets at the rear of the oven:
24 V DC +

24 V DC -

1 2 3

Figure 13: Pin configuration of the DIN sockets (15) and (16)

OPERATION LINE 2 OPERATION LINE 1

OUTPUT OUTPUT
24V DC / MAX. 0,4A 24V DC / MAX. 0,4A

Figure 14: Legend at the DIN socket (15) Figure 15: Legend at the DIN socket (16)

A suitable DIN plug is enclosed.

VD (E2.1) 09/2018 page 57/95

Maximum loading capacity of the switching contacts: 0.4 Amp.

CAUTION
Overloading the switching contacts.
Damage to the switching contacts and connection sockets.
∅ DO NOT exceed the maximum switching load of 0.4 Amp.
∅ DO NOT connect any device with a higher load.
 ONLY connect devices with a nominal tension of 24 V DC.

16. Options

16.1 Connection kit VD (option)

The VD connection kit VD (Art. no. 8012-0146)
consists of:
• Aluminum straining ring DN10/16
• Outer centering ring DN10/16
• Small flange with hose tulles DN16/8
• 2.5 m / 98.4 in India rubber hose 6/12 mm
• 2 hose clamps

Figure 16: VD connection kit VD

16.2 Vacuum module empty (without pump) (option)

The mounting instructions Art. no. 7001-0137 supplied with the vacuum module describe
how to mount the VD vacuum drying oven onto the vacuum module and installing the
suction line into the vacuum module.

A switch (18) is located at the front of the vacuum module for switching a vacuum pump via the socket
(19) permanently fitted in the vacuum module.

(18) (19)

Figure 17: Vacuum module with the switch and socket for the vacuum pump
(18) Switch for the vacuum pump
(19) Socket for the vacuum pump

VD (E2.1) 09/2018 page 58/95

Maximum admissible load of the socket:
Standard 230 V / 50 Hz - 16 Amp
cUL-version 120 V / 60 Hz - 13 Amp

With CUL-version, connect only a UL listed vacuum pump with ratings of 120 V AC, 60 Hz, and
less or equal 12 Amp, 0.5 HP.

(13)
Connection to a vacuum source

Connect the vacuum connection (13) (small flange DN 16) at the

rear of the chamber at the top to a vacuum pump or to a domestic
vacuum system via a vacuum hose or a fixed vacuum pipe.
When using a vacuum hose, we recommend using the BINDER
connection kit VD Art. no. 8012-0146 (chap. 16.1. The module has
an appropriate hose outlet at the back.

Figure 18: VD 53 with option “Vacuum module”, mounted, and

installed vacuum hose

CAUTION
Technical defects due to excessive negative pressure.
Danger of implosion.
Damage to the chamber.
∅ The end vacuum must NOT fall below the permissible level of 10 mbar / 0.0003 inHg.
-2

 Install the pump according to the permissible end vacuum or limit the end vacuum via a
vacuum controller.

WARNING
Release of extracted vapors.
Danger of injury.
Damage to oven and pump by corrosion.
 Remove the extracted vapors from the module via a suitable hose into e.g., a fume
extractor facility.
 Connect the hose to the vacuum pump outlet.

VD (E2.1) 09/2018 page 59/95

16.3 Vacuum module with chemical membrane pump VP 1.1 or VP 2.1 (option)

The mounting instructions Art. no. 7001-0137 supplied with the vacuum module describe
how to mount the VD vacuum drying oven onto the vacuum module and installing the
suction line into the vacuum module.

(15) (15) DIN socket (operation line 2) for option

program controlled venting
(16) DIN socket (operation line 1) for option
(16)
vacuum module with pump
(20) DIN socket at the vacuum module for
option vacuum module with pump
(21) Power supply at vacuum module
(22) Fuse

(20)
(21)

(22)

Figure 19: VD 53 with option “Vacuum module

with chemical membrane pump”, mounted

A switch (18) is located at the front of the vacuum module for switching the vacuum pump via the socket
(19) permanently fitted in the vacuum module.

(18) (19)

Figure 20: Vacuum module with switch and socket for vacuum pump
(18) Switch for vacuum pump
(19) Socket for vacuum pump

VD (E2.1) 09/2018 page 60/95

Maximum admissible load of the socket:
Standard 230 V / 50 Hz - 16 Amp
cUL-version 120 V / 60 Hz - 13 Amp

With cUL-version, connect only a UL listed vacuum pump with ratings of 120 V AC, 60 Hz, and
less or equal 12 Amp, 0.5 HP.

The VP 1.1 or VP 2.1 membrane pump is located in a separate transport packaging. With this option, the
mounted system, consisting of VD and vacuum module, has a total of two power supply leads.
Installation of the supplied vacuum pump
• The vacuum drying oven is mounted onto the vacuum module as described in the mounting
instructions Art. No. 7001-0137.
• The suction line is installed to the vacuum module as described in the mounting instructions Art. No.
7001-0137.
• When the pump is removed from the original packaging, place it in the vacuum module.
• Push the pre-installed suction line onto the opening of the vacuum pump (13) hose olive above the
suction-side condensate piston).
• Insert the shockproof plug of the vacuum pump into the permanently installed socket (19) in the
vacuum module.
• Push a suitable hose for removing the extracted vapors from the module onto the pressure-side
connection of the vacuum pump (hose olive at the back of the emission condenser at the top).
• Lead the hose end into an exhaust air unit.
• Connect DIN socket (20) at the vacuum module to DIN socket (16) at the chamber rear via the
supplied 1.2 m cable.

As soon as the connection between DIN sockets (16) and (20) is established, it is not possible
to manually switch the pump via switch (18).

To permit switching on and off the pump via operation line 1, keep switch (18) switched on
(position I).

WARNING
Release of extracted vapors.
Danger of injury.
Damage to oven and pump by corrosion.
 Remove the extracted vapors from the module via a suitable hose into e.g., a fume
extractor facility.
 Connect the hose to the vacuum pump outlet (hose olive at the back of the emission
condenser at the top).

You can connect a laboratory cooling system to the emission condenser of the vacuum pumps
VP 1.1 or VP 2.1.

For operating the chemical membrane pumps VP 1.1 (MZ2C) and VP 2.1 (MD4C), please
refer to the enclosed pump manufacturer's operating manual.

VD (E2.1) 09/2018 page 61/95

Observe the permitted gas temperature. The following values refer to the maximum ambient temperature
of the pump of 40 °C / 104°F.
Operation condition Inlet pressure Permitted gas temperature
Continuous operation > 100 mbar / 2.95 inHg (high gas load) +10 °C to +40 °C / 50°F to 104°F
Continuous operation < 100 mbar / 2.95 inHg (low gas load) 0 °C to +60 °C / 32°F to 140°F
Short-time operation (< 5 min.) < 100 mbar / 2.95 inHg (low gas load) -10 °C to +80 °C / 50°F to 176°F
Do not exceed the permitted gas inlet temperature. An excessive gas inlet temperature may diminish the
lifetime of the pump.

CAUTION
Exceeding the gas inlet temperature.
Damage to the vacuum pump.
∅ Do NOT exceed the set-point temperature of the permitted gas temperature.
 With higher set-point temperature, take appropriate measures to cool down the sucked-
in gas before its entry to the vacuum pump

16.4 Vacuum module with speed controlled chemical membrane pump VP 3.1
and vacuum controller (option)
This option consists of:
• The pump stand with speed-controlled chemical vacuum pump VP 3.1 (suction power 4.6 m /h) and
3

vacuum controller CVC3000

• Vacuum module with accompanying mounting instructions

The mounting instructions 7001-0137 delivered with the vacuum module describe
mounting the vacuum drying oven onto the vacuum module and installing the suction line
to the vacuum module.

The chemical vacuum pump and the vacuum controller are delivered ready-assembled as a vacuum
pump stand in separate transport packaging. For installation and connection, see chap. 16.3.

Do NOT connect DIN sockets (16) and (20) when using this option.

To permit switching on and off the pump, keep switch (18) switched on (position I).

For operating the chemical membrane pump VP 3.1 (MD4C Vario), please refer to the
enclosed pump manufacturer's operating manual.

Observe the permitted gas temperature. The following values refer to the maximum ambient temperature
of the pump of 40 °C / 104°F.
Operation condition Inlet pressure Permitted gas temperature
Continuous operation > 100 mbar / 2.95 inHg (high gas load) +10 °C to +40 °C / 50°F to 104°F
Continuous operation < 100 mbar / 2.95 inHg (low gas load) 0 °C to +60 °C / 32°F to 140°F
Short-time operation (< 5 min.) < 100 mbar / 2.95 inHg (low gas load) -10 °C to +80 °C / 50°F to 176°F

VD (E2.1) 09/2018 page 62/95

Do not exceed the permitted gas inlet temperature. An excessive gas inlet temperature may reduce the
pump’s lifetime.

CAUTION
Exceeding the gas inlet temperature.
Damage to the vacuum pump.
∅ Do NOT exceed the set-point temperature of the permitted gas temperature.
 With higher set-point temperature, take appropriate measures to cool down the sucked-
in gas before its entry to the vacuum pump

Programming of descendant pressure cycles as well as documentation of pressure data are possible via
the RS 232 serial interface of the vacuum controller CVC 3000 by use of the BINDER communication
software APT-COM™ DataControlSystem (option, chap. 16.8).

In combination with the option object temperature measurement a T-formed connection tube
adapter (small flange DN16 (Art. No. 6009-0060) NOT included) is necessary to connect the
pressure sensor of the vacuum controller to the measuring access port.

Settings of the vacuum controller for control via APT-COM™:

Following settings are necessary to set the vacuum controller to remote control via its RS232 interface
and to enable the venting valve:
Setting for remote control:
• With the MODE key select the menu “Configuration”.
• Select the menu point “RS – 232” with the selection knob and set the setting “Remote” to “On”.
• Set the Baud rate to 9600.

Configuration RS - 232
Adjustment 936 mbar Baud 9600
RS – 232 . . . Parity 8-N-1
Sensors . . . Handshake Xon - Xoff
Display . . . Remote On
Autostart Off - - - - - - Back - - - - - -
Defaults Cancel
- - - - - - Back - - - - - -

The vacuum controller can no longer be operated manually in this mode.

Resetting to manual operation:

Turn off the pump unit at its main RS - 232
power switch. Then turn it on again
and within 1 second press down Baud 9600
simultaneously the selection knob
and the ON/OFF key. Parity 8-N-1
OR Handshake Xon - Xoff
Turn off the pump unit at ON/OFF Remote Off
key. Then turn it on again and within - - - - - - Back - - - - - -
1 second press the selection knob.

VD (E2.1) 09/2018 page 63/95

Then select the menu point “RS - 232” with the selection knob and set the setting “Remote” to “Off.

16.5 Digital pressure display (option)

With this option, a digital display indicates the internal pressure with the accuracy of 1 mbar / 0.03 inHg.
The pressure is measured by a permanently fitted internal pressure sensor.
A service engineer can calibrate and internally adjust the digital pressure display.

Figure 21: Digital display of internal pressure

16.6 Additional measuring channel for digital object temperature display with
flexible Pt 100 temperature sensor (option)
The object temperature display permits recording the object temperature directly on or in the drying
material. The object temperature is measured via a flexible Pt100 sensor inside the inner chamber. The
sensor needs to be in thermally conducting contact with the charging material. It can be plunged into
humid charging material up to the length of its protecting tube.
The object temperature is indicated on Display 2 of the RD3 controller.
C
Display 1 shows e.g. 24.6 (actual temperature value)
Display 2 shows 24.4 15:41 (actual object temperature in °C, actual time)

Figure 22: Figure 23:

Standard Display without the Display with the
object temperature display option object temperature display option

The object temperature data is put out combined with the temperature data of the temperature controller
to the RS 422 interface as a second measuring channel. This permits recording by the BINDER
documentation software APT-COM™ DataControlSystem (option, chap. 16.8).
Assembly and connection of the object temperature recording
• Insert the Pt 100 temperature sensor from the rear through the measuring connection (17) into the
inner chamber.
• The 3 contacts of the Pt 100 sensor are conducted outside via a measuring access port. From there,
establish the connection to the DIN socket at the top of the rear panel of the chamber marked “Pt100”.

VD (E2.1) 09/2018 page 64/95

Figure 24: Measuring connection (17) with Figure 25: Pt100 connection (14) at the rear of the
measuring access port chamber
Technical data of the Pt 100 sensor:
• Three-wire technique
• Class B (DIN EN 60751)
• Temperature range up to 300 °C / 572°F
• Stainless steel protective tube, length 45 mm / 1.77 in, stainless steel material no. 1.4501

16.7 Measuring access port vacuum 9 poles (option)

The measuring access port allows creating electrical connections for low voltages or sensors between the
exterior and interior of the VD vacuum drying oven. A 9 poles plug for the outside is included.

Figure 26: Measuring connection (17) with measuring access

port and supplied plug

Connections at the measuring access port

• At the inner side of the measuring access port you can solder up to 9 cables. The inside connections
must be insulated against each other and against ground. Use 300 °C / 572 °F solder.
• The 9 contacts are conducted outside via the measuring access port. You can use them to connect a
device via the delivered plug.
Maximum load capacity of the switching contacts: 42 V AC/DC - 2A

DANGER
Electrical hazard.
Danger of death.
Damage to switching contacts and connection socket.
∅ Do NOT exceed the maximum switching load of 42 AC/DC – 2Amp.
∅ Do NOT connect any devices with a higher load capacity.
 Insulate the inside connections against each other and against ground. Use 300 °C /
572 °F solder.

VD (E2.1) 09/2018 page 65/95

16.8 Communication software APT-COM™ 3 DataControlSystem (option)
The chamber is regularly equipped with a serial interface RS 422 (9) that can connect the BINDER
communication software APT-COM™ 3 DataControlSystem. The actual temperature value is given at
adjustable intervals. Programming can be performed graphically via PC. Up to 30 chambers with RS 422
interface can be cross-linked. For further information, refer to the operating manual of the BINDER
communication software APT-COM™ 3.

Confirm that the interface mode is correctly set to “Modbus” in the user level (chap. 10).

Pin allocation of the RS 422 interface (9): pin 2: RxD (+)

pin 3: TxD (+)
pin 4: RxD (-)
pin 5: TxD (-)
pin 7: GND

17. Maintenance, cleaning, and service

17.1 Maintenance intervals, service

DANGER
Electrical hazard.
Danger of death.
∅ The chamber must NOT become wet during operation or maintenance work.
∅ Do NOT remove the rear panel of the chamber.
 Before conducting maintenance work, turn off the chamber at the main power switch
and disconnect the power plug.
 Ensure all maintenance work is conducted by licensed electricians or experts authorized
by BINDER.

Ensure regular maintenance work is performed at least once a year.

The warranty becomes void if maintenance work is conducted by non-authorized personnel.

Replace the door gasket only when cold. Otherwise, the door gasket may become damaged.

We recommend taking out a maintenance agreement. Please consult BINDER Service.

BINDER telephone hotline: +49 (0) 7462 2005 555
BINDER fax hotline: +49 (0) 7462 2005 93555
BINDER e-mail hotline: [email protected]
BINDER service hotline USA: +1 866 885 9794 or +1 631 224 4340 x3 (toll-free in the USA)
BINDER service hotline Asia Pacific: +852 390 705 04 or +852 390 705 03
BINDER service hotline Russia and CIS +7 495 988 15 16
BINDER Internet website http://www.binder-world.com
BINDER address BINDER GmbH, post office box 102, D-78502 Tuttlingen

International customers, please contact your local BINDER distributor.

VD (E2.1) 09/2018 page 66/95

17.2 Cleaning and decontamination
Clean the chamber after each use to avoid potential corrosion damage by ingredients of the charging
material.

DANGER
Electrical hazard.
Danger of death.
∅ Do NOT spill water or cleaning agents over the inner and outer surfaces.
 Before cleaning, turn off the chamber at the main power switch and
disconnect the power plug.
 Completely dry the appliance before turning it on again.

17.2.1 Cleaning

Disconnect the oven from the power supply before cleaning. Disconnect the power plug.

The interior of the chamber must be kept clean. Thoroughly remove any residues of the
charging material

Wipe the surfaces with a moistened towel. In addition, you can use the following cleaning agents:

Exterior surfaces, Standard commercial cleaning detergents free from acid or halides.
inner chamber,
Alcohol based solutions.
door gaskets
We recommend using the neutral cleaning agent Art. No. 1002-0016.
Expansion racks, Standard commercial cleaning detergents free from acid or halides, no salt
rack holders solution or chlorinated solvents.
We recommend using the neutral cleaning agent Art. No. 1002-0016.
Instrument panel Standard commercial cleaning detergents free from acid or halides.
We recommend using the neutral cleaning agent Art. No. 1002-0016.
Zinc coated hinge parts Standard commercial cleaning detergents free from acid or halides.
rear chamber wall
Do NOT use a neutral cleaning agent on zinc coated surfaces.

Do not use cleaning agents that may cause a hazard due to reaction with components of the device or the
charging material. If there is doubt regarding the suitability of cleaning products, please contact BINDER
service.

We recommend using the neutral cleaning agent Art. No. Art. Nr. 1002-0016 for a thorough
cleaning.
Any corrosive damage that may arise following use of other cleaning agents is excluded from
liability by BINDER GmbH.
Any corrosive damage caused by a lack of cleaning, is excluded from liability by BINDER
GmbH.

VD (E2.1) 09/2018 page 67/95

 CAUTION
Danger of corrosion.
Damage to the chamber.
∅ Do NOT use acidic or chlorine cleaning detergents.
∅ Do NOT use a neutral cleaning agent on other kind of surfaces e.g., the zinc coated
hinge parts or the rear chamber wall.

For surface protection, perform cleaning as quickly as possible.

After cleaning completely remove cleaning agents from the surfaces with a moistened towel.
Let the chamber dry.

Soapsuds may contain chlorides and must therefore NOT be used for cleaning.

With every cleaning method, always use adequate personal safety controls.

Following cleaning, leave the chamber door open or remove the access port plugs.

The neutral cleaning agent may cause health problems in contact with skin and if ingested.
Follow the operating instructions and safety hints labeled on the bottle of the neutral
cleaning agent.

Recommended precautions: To protect the eyes use sealed protective goggles. Suitable protective gloves
with full contact: butyl or nitrile rubber, penetration time >480 minutes.

CAUTION
Contact with skin, ingestion.
Skin and eye damage due to chemical burns.
∅ Do not ingest. Keep away from food and beverages.
∅ Do NOT empty into drains.
 Wear protective gloves and goggles.
 Avoid skin contact.

17.2.2 Decontamination

The operator must ensure that proper decontamination is performed in case a contamination of the
chamber by hazardous substances has occurred.
Disconnect the chamber from the power supply prior to chemical decontamination. Disconnect the power
plug.
Do not use decontamination agents that may cause a hazard due to reaction with components of the
device or the charging material. If there is doubt regarding the suitability of cleaning products, please
contact BINDER service.

VD (E2.1) 09/2018 page 68/95

You can use the following disinfectants:

Inner chamber Standard commercial surface disinfectants free from acid or halides.
Alcohol based solutions.
We recommend using the disinfectant spray Art. No. 1002-0022.

For chemical disinfection, we recommend using the disinfectant spray Art. No. 1002-0022.
Any corrosive damage that may arise following use of other disinfectants is excluded from
liability by BINDER GmbH.

With every decontamination method, always use adequate personal safety controls.

In case of contamination of the interior by biologically or chemically hazardous material, there are two
possible procedures depending on the type of contamination and charging material.
(1) Vacuum drying ovens VD can be sterilized at 190 °C / 374 °F for at least 30 minutes. All inflammable
goods must be removed from the interior before.
(2) Remove the vacuum expansion racks and removable rack holders and spray the inner chamber with
an appropriate disinfectant.
If desired you can sterilize the vacuum expansion racks and removable rack holders in a sterilizer or
autoclave. Before start-up, the chamber must be absolutely dry and ventilated, as explosive gases
may form during the decontamination process.

In case of eye contact, the disinfectant spray may cause eye damage due to chemical
burns. Follow the operating instructions and safety hints labeled on the bottle of the
disinfectant spray.

Recommended precautions: To protect the eyes use sealed protective goggles.

CAUTION
Eye contact.
Eye damage due to chemical burns.
∅ Do NOT empty into drains.
 Wear protective goggles.

After using the disinfectant spray, allow the chamber to dry thoroughly, and aerate it
sufficiently.

VD (E2.1) 09/2018 page 69/95

17.3 Sending the chamber back to BINDER GmbH
If you return a BINDER product to us for repair or any other reason, we will only accept the product upon
presentation of an authorization number (RMA number) that has previously been issued to you. An
authorization number will be issued after receiving your complaint either in writing or by telephone prior to
your sending the BINDER product back to us. The authorization number will be issued following receipt of
the information below:
• BINDER product type and serial number
• Date of purchase
• Name and address of the dealer from which you bought the BINDER product
• Exact description of the defect or fault
• Complete address, contact person and availability of that person
• Exact location of the BINDER product in your facility
• A contamination clearance certificate (chap. 23) must be faxed in advance
The authorization number must be applied to the packaging in such a way that it can be easily recognized
or be recorded clearly in the delivery documents.

For security reasons we cannot accept a chamber delivery if it does not carry an authorization
number.

Return address: BINDER GmbH Gänsäcker 16

Abteilung Service 78502 Tuttlingen
Germany

18. Disposal

18.1 Disposal of the transport packing

Packing element Material Disposal

Straps to fix packing on pallet Plastic Plastic recycling
Wooden transport box (option) Non-wood (compressed
Wood recycling
matchwood, IPPC standard)
with metal screws Metal Metal recycling
Pallet Solid wood (IPPC standard) Wood recycling
with foamed plastic stuffing PE foam Plastic recycling
Shipping box Cardboard Paper recycling
with metal clamps Metal Metal recycling
Top cover Cardboard Paper recycling

Cardboard Paper recycling

Removal aid
(size 115)
Plastic Plastic recycling
®
Edge protection Styropor or PE foam Plastic recycling
Protection of doors PE foam Plastic recycling
Bag for operating manual PE foil Plastic recycling
Insulating air cushion foil (packing of
PE foil Plastic recycling
optional accessories)
If recycling is not possible, all packing parts can also be disposed of with normal waste.

VD (E2.1) 09/2018 page 70/95

18.2 Decommissioning

• Turn off the main power switch (1) (position 0).

When turning off the main power switch (1), the stored parameters remain saved.

• Close the inert gas supply:

VD23: Close the fine dosing valve (4) for inert gas / ambient air supply.
VD53, VD115: Close the fine dosing valve (6) for inert gas supply.
Through the open inert gas connection, inert gas can enter the vacuum drying oven and escape into
the ambient air.

WARNING
High concentration of inert gas.
Risk of death by suffocation.
 Respect the relevant regulations for handling these gases.
 When decommissioning the VD vacuum drying oven, turn off the inert gas supply:
close valves (4) or (6).

• Turn off the vacuum pump. Break the vacuum as described in chap. 14.2
• Disconnect the oven from the power supply. Pull the power plug.
• Remove the vacuum connection (chap. 4.2).
• Remove the inert gas connection and the pressure reducer (chap. 4.3).
Temporal decommissioning: See indications for appropriate storage, chap. 3.3.
Final decommissioning: Dispose of the chamber as described in chap. 18.3 to 18.5.

18.3 Disposal of the chamber in the Federal Republic of Germany

According to Annex I of Directive 2012/19/EU of the European Parliament and of the Council on waste
electrical and electronic equipment (WEEE), BINDER devices are classified as “monitoring and control
instruments” (category 9) only intended for professional use“. They must not be disposed of at public
collecting points.
The chambers bear the symbol for the marking of electrical and electronic equipment
manufactured / placed on the market in the EC after 13 August 2005 and be disposed of in
separate collection according to Directive 2012/19/EU on waste electrical and electronic
equipment (WEEE) and German national law for electrical and electronic equipment
(Elektro- und Elektronikgerätegesetz, ElektroG). WEEE marking: crossed-out wheeled bin
with solid bar under. A significant part of the materials must be recycled in order to protect
the environment.
At the end of the device’s service life, have the chamber disposed of according to the German national
law for electrical and electronic equipment (Elektro- und Elektronikgerätegesetz, ElektroG from 20
October 2015, BGBl. I p. 1739) or contact BINDER service who will organize taking back and disposal of
the chamber according to the German national law for electrical and electronic equipment (Elektro- und
Elektronikgerätegesetz, ElektroG from 20 October 2015, BGBl. I p. 1739).

VD (E2.1) 09/2018 page 71/95

 CAUTION
Violation against existing law.
∅ Do NOT dispose of BINDER devices at public collecting points.
 Have the device disposed of professionally at a recycling company which is certified
according to the German national law for electrical and electronic equipment (Elektro-
und Elektronikgerätegesetz, ElektroG from 20 October 2015, BGBl. I p. 1739).
or
 Instruct BINDER Service to dispose of the device. The general terms of payment and
delivery of BINDER GmbH apply, which were valid at the time of purchasing the
chamber.

Certified companies disassemble waste (used) BINDER equipment in primary substances for recycling
according to Directive 2012/19/EU. The devices must be free from toxic, infectious or radioactive
substances in order to eliminate any health hazards to the employees of the recycling companies.

Prior to handing the chamber over to a recycling company, it is the user’s responsibility that it is
free from toxic, infectious or radioactive substances.
• Prior to disposal, clean all introduced or residual toxic substances from the chamber.
• Prior to disposal, disinfect the chamber from all sources of infection. Be aware that sources
of infection may also be located outside the inner chamber.
• If you cannot safely remove all toxic substances and sources of infection from the chamber,
dispose of it as “special” waste according to national law.
• Fill out the contamination clearance certificate (chap. 23) and enclose it with the chamber.

WARNING
Contamination of the device with toxic, infectious or radioactive substances.
Danger of intoxication.
Danger of infection.
∅ NEVER take a chamber contaminated with toxic substances or sources of infection for
recycling according to Directive 2012/19/EU.
 Prior to disposal, remove all toxic substances and sources of infection from the
chamber.
 A chamber from which all toxic substances or sources of infection cannot be safely
removed must be considered as “special” waste according to national law. Dispose of it
accordingly.

18.4 Disposal of the chamber in the member states of the EU except for the
Federal Republic of Germany
According to Annex I of Directive 2012/19/EU of the European Parliament and of the Council on waste
electrical and electronic equipment (WEEE), BINDER devices are classified as “monitoring and control
instruments” (category 9) only intended for professional use“. They must not be disposed of at public
collecting points.
The chambers bear the symbol for the marking of electrical and electronic equipment
manufactured / placed on the market in the EC after 13 August 2005 and be disposed of in
separate collection according to the Directive 2012/19/EU on waste electrical and electronic
equipment (WEEE). WEEE marking: crossed-out wheeled bin with solid bar under.

VD (E2.1) 09/2018 page 72/95

At the end of the device’s service life, notify the distributor who sold you the device, who will take back and
dispose of the chamber according to the Directive 2012/19/EU on waste electrical and electronic
equipment (WEEE).

CAUTION
Violation against existing law.
∅ Do NOT dispose of BINDER devices at public collecting points.
 Have the device disposed of professionally at a recycling company that is certified
according to conversion of the Directive 2012/19/EU into national law.
or

 Instruct the distributor who sold you the device to dispose of it. The agreements apply
that were agreed with the distributor when purchasing the chamber (e.g. his general
terms of payment and delivery).
 If your distributor is not able to take back and dispose of the chamber, please contact
BINDER service.

Certified companies disassemble waste (used) BINDER equipment in primary substances for recycling
according to Directive 2012/19/EU. The devices must be free from toxic, infectious or radioactive
substances in order to eliminate any health hazards to the employees of the recycling companies.

Prior to handing the chamber over to a recycling company, it is the user’s responsibility that it is
free from toxic, infectious or radioactive substances.
• Prior to disposal, clean all introduced or residual toxic substances from the chamber.
• Prior to disposal, disinfect the chamber from all sources of infection. Be aware that sources
of infection may also be located outside the inner chamber.
• If you cannot safely remove all sources of infection and toxic substances from the chamber,
dispose of it as “special” waste according to national law.
• Fill out the contamination clearance certificate (chap. 23) and enclose it with the chamber.

WARNING
Contamination of the device with toxic, infectious or radioactive substances.
Danger of intoxication.
Danger of infection.
∅ NEVER take a chamber contaminated with toxic substances or sources of infection for
recycling according to Directive 2012/19/EU.
 Prior to disposal, remove all toxic substances and sources of infection from the
chamber.
 A chamber from which all toxic substances or sources of infection cannot be safely
removed must be considered as “special” waste according to national law. Dispose of it
accordingly.

VD (E2.1) 09/2018 page 73/95

18.5 Disposal of the chamber in non-member states of the EU

CAUTION
Alteration of the environment.
 For final decommissioning and disposal of the vacuum drying oven, please contact
BINDER Service.
 Follow the statutory regulations for appropriate, environmentally friendly disposal.

The main board of the vacuum drying oven includes a lithium cell. Please dispose of it according to
national regulations.

19. Troubleshooting
Fault description Possible cause Required measures
General
No power supply. Check connection to power supply.
Check power supply for voltage of
Wrong voltage.
115V or 230V.
Chamber fuse has responded. Check chamber fuse.
Allow the oven to cool down the
Chamber permanently turned oven and press the “RESET”
off. Safety device has turned off the button. Check temperature set-
oven. point and setting of safety device
(chap. 12). If appropriate, select
suitable limit value.
Safety device defective.
Contact BINDER Service.
Controller defective.
Heating
Chamber door not properly
Completely close chamber door.
Set-point temperature is not closed.
reached after specified time. Door gasket defective. Replace door gasket,
Controller not adjusted. Calibrate and adjust controller.
Controller defective.
Chamber heating permanently, Pt 100 sensor defective. Contact BINDER Service.
set-point not held. Semiconductor relay defective
Controller not adjusted. Calibrate and adjust controller.
Chamber doesn’t heat up. Heating element defective.
Contact BINDER Service.
LED (7a) “Heating active” lit. Semiconductor relay defective.
Allow the oven to cool down the
oven and press the “RESET”
Safety device has turned off the button. Check temperature set-
Chamber doesn’t heat up. oven. point and setting of safety device
LED (7a) “Heating active” not lit. (chap. 12). If appropriate, select
suitable limit value.
Semiconductor relay defective.
Contact BINDER Service.
Controller defective.
Deviations from the indicated Charge the oven less or consider
Oven fully loaded.
heating-up times. longer heating-up times.

VD (E2.1) 09/2018 page 74/95

Fault description Possible cause Required measures
Heating (continued)
Use the delivered expansion racks
Deviations from the temperature
Invalid calibration only. Do NOT change between
set-point in equilibrated state.
aluminum and stainless steel racks
Reference temperature sensor Fix the reference temperature
has insufficient contact to sensor with thermal conductive
Wrong temperature value expansion rack. paste or adhesive aluminum tape.
measured during calibration. Leakage current when using a
Mount a thermo element electrically
thermo element not electrically
isolated from the rack.
isolated.
Vacuum
Door gasket defective. Replace door gasket,
Safety glass panel defective. Replace safety glass panel.
Vacuum not held. Gaskets of small flange
Replace gaskets of small flange
connections (universal eccentric
connections.
ring) defective.
Inner tube connection leaky. Contact BINDER Service.
Controller
For rapid transition phases, do NOT
Program duration longer than Inappropriate tolerances have
program tolerance limits in order to
programmed. been programmed.
permit maximum heating speed.
When programming, define the end
value of the desired cycle by adding
Program stops one section too
Program line is incomplete. an additional section with a section
early.
time of at least one minute (with
setting “ramp”).
Change from 2 programs to 1 When changing, ensure that the
Programs have been deleted.
program or vice-versa programs are no longer needed.
The controller returns to Normal No button was pressed for more Repeat entries, enter the values
Display from any level. than 120 sec. rapidly.
Message RANGE ERROR CH1 Sensor rupture between sensor
Contact BINDER Service.
in Normal Display in Display 2 and controller
Set-point programming type set Set the set-point programming type
Ramp temperature transitions
to “Step” in the User level (chap. to setting “Ramp” in the User level
are only realized as steps.
10). (chap. 10).

Only qualified service personnel authorized by BINDER must perform repair.

Repaired chambers must comply with the BINDER quality standards.

VD (E2.1) 09/2018 page 75/95

20. Technical description

20.1 Factory calibration and adjustment

This chamber was calibrated and adjusted in the factory. Calibration and adjustment were performed
using standardized test instructions, according to the QM DIN EN ISO 9001 system applied by BINDER
(certified since December 1996 by TÜV CERT). All test equipment used is subject to the administration of
measurement and test equipment that is also a constituent part of the BINDER QM DIN EN ISO 9001
systems. They are controlled and calibrated to a DKD-Standard at regular intervals.
Factory adjustment was done in the center of the usable volume and under vacuum conditions. the sensor
is fixed in the middle of the expansion rack in a way ensuring good thermal conductivity (heat conduction).
Measuring is performed in equilibrated state.

CAUTION
Invalid calibration.
∅ Do NOT change between aluminum and stainless steel racks.
 Use the delivered expansion racks only.

20.2 Technical data

Chamber size 23 53 115

External dimensions
Vacuum oven
Width, net mm / inch 515 / 20.28 634 / 24.96 740 / 29.13
Height, gross (including feet) mm / inch 655 / 25.79 775 / 30.51 900 / 35.43
Depth, net mm / inch 500 / 19.69 550 / 21.65 670 / 26.38
Depth, gross (including door handle,
mm / inch 600 / 23.62 650 / 25.59 770 / 30.31
connections)
Vacuum module (option)
Width, net mm / inch 515 / 20.28 634 / 24.96 740 / 29.13
Height, net mm / inch 624 / 24.57 624 / 24.57 622 / 24.49
Depth, net mm / inch 500 / 19.69 550 / 21.65 670 / 26.38
Depth, gross (including door handle,
mm / inch 600 / 23.62 650 / 25.59 770 / 30.31
connections)
Chamber with optional vacuum module
Width, net mm / inch 515 / 20.28 634 / 24.96 740 / 29.13
Height, net mm / inch 1279 / 50.35 1400 / 55.12 1522 / 59.92
Depth, net mm / inch 500 / 19.69 550 / 21.65 670 / 26.38
Depth, gross (including door handle,
mm / inch 600 / 23.62 650 / 25.59 770 / 30.31
connections)
Wall clearances
Wall clearance, rear (minimum) mm / inch 100 / 3.94 100 / 3.94 100 / 3.94
Wall clearance, side (minimum) mm / inch 135 / 5.31 135 / 5.31 135 / 5.31
Internal dimensions
Width mm / inch 285 / 11.22 400 / 15.75 506 / 19.92
Height mm / inch 285 / 11.22 400 / 15.75 506 / 19.92
Depth mm / inch 295 / 11.61 340 / 13.38 460 / 18.11
Interior volume l / cu.ft. 23 / 0.8 53 / 1.9 115 / 4.1

VD (E2.1) 09/2018 page 76/95

Chamber size 23 53 115
Racks
Number of expansion racks (aluminum), series 2 2 2
Number of expansion racks (aluminum), max. 4 5 6
Distance between the racks mm / inch 53 / 2.09 62 / 2.44 68 / 2.68
234 x 280 / 349 x 320 / 455 x 440 /
Usable space per rack (width x depth) mm / inch
9.21 x 11.02 13.74 x 12.60 17.91 x 17.32
Permissible load per rack Kg / lbs 20 / 44 20 / 44 20 / 44
Permissible total load Kg / lbs 35 / 77 45 / 99 65 / 143
Weight
Weight (empty) Kg / lbs 63 / 139 95 / 209 153 / 337
Temperature data
Temperature range approx. 15 °C / 27 °F
°C / °F 200 / 392 200 / 392 200 / 392
above room temperature up to
Temperature fluctuation ±K 0.1 0.1 0.1
Temperature uniformity at 100 °C / 212°F ±K 1.5 2 3,5
(variation) at 200 °C / 392°F ±K 3 4.5 9
to 100 °C / 212°F min 65 80 95
Heating up time
to 200 °C / 392°F min 100 115 150
Vacuum data
Vacuum connection with small flange DN mm / inch 16 / 0.63 16 / 0.63 16 / 0.63
Measuring access port with small flange DN mm / inch 16 / 0.63 16 / 0.63 16 / 0.63
Inert gas connection with flow-limiter
∅ mm / inch 8 / 0.31 8 / 0.31 8 / 0.31
Adapter with hose olive
-2 -2 -2
Permitted end vacuum mbar / inHg 1x10 / 0.0003 1x10 / 0.0003 1x10 / 0.0003
-2 -2 -2
Leak rate bar/h / inHg /h 1x10 / 0.295 1x10 / 0.295 1x10 / 0.295
Electrical data
(model versions VD023-230V, VD053-230V, VD115-230V)
IP protection type according to EN 60529 IP 20 20 20
Nominal at 50 Hz power frequency V 230 230 230
voltage
(±10%) at 60 Hz power frequency V 230 230 230
Nominal power kW 0.80 1.20 1.90
Chamber fuse 5 x 20 mm / 250V / middle-
Amp 10 10 10
time-lag (M)
Power plug shock proof plug
Power plug of vacuum module (option) shock proof plug
Over-voltage category acc. to IEC 61010-1 II II II
Pollution degree acc. to IEC 61010-1 2 2 2
Different electrical data for VD-UL constructed for the USA and Canada
(model versions VD023UL-120V, VD053UL-120V, VD115UL-120V)
Nominal voltage (±10%) at 60 Hz power
V 115 115 115
frequency
Nominal power kW 0.80 1.20 1.70
Nominal current A 7.0 10.5 14.8
Chamber fuse 6.3 X 32 mm / 250V / super-
A 12.5 12.5 20
time-lag TT
Power plug NEMA 5-15P 5-15P 5-20P
Power plug of vacuum module (option) NEMA 5-15P 5-15P 5-20P

VD (E2.1) 09/2018 page 77/95

Chamber size 23 53 115
Environment-specific data
Noise level VD (mean value) dB (A) < 45 < 45 < 45
at 100 °C / 212°F Wh/h 105 150 250
Energy consumption
at 200 °C / 392°F Wh/h 280 445 785
All technical data is specified for unloaded chambers with standard equipment (with aluminum racks) at
an ambient temperature of +22 °C ± 3 °C / 71.6 °F ± 5.4 °F and a power supply voltage fluctuation of ±10.
Technical data is determined in accordance to BINDER Factory Standard Part 1:2015 following DIN
12880:2007.
All indications are average values, typical for chambers produced in series. We reserve the right to
change technical specifications at any time.

20.3 Equipment and options (extract)

To operate the chamber, use only original BINDER accessories or accessories / components
from third-party suppliers authorized by BINDER. The user is responsible for any risk arising
from using unauthorized accessories.

Regular equipment
Microprocessor program controller RD3 with LED display
Safety device class 2 according to DIN 12880:2007
RS 422 printer and communication interface with adjustable printing intervals
Fine-dosing aeration valve
Inert gas connection with fine-dosing valve
Analog pressure display (manometer) (not with option digital pressure display)
Measuring connection (DN 16), rear
Safety glass panel
2 switching contacts 24V DC via operation lines
Intelligent adaptation of the heating power by soft heating-up function (selectable on-off)

Options / accessories
Expansion racks, aluminum or stainless steel 1.4571
FKM door gasket (temperature resistant up to 200 °C / 392 °F)
Additional measuring channel for digital object temperature display with flexible Pt 100 temperature
sensor
Digital pressure display (adjustable)
Communication software APT-COM™ for logging and display of temperature data and networking up to
30 chambers with PC
Protocol printer for numeric and graphic temperature documentation (available via BINDER INDIVIDUAL
customized solutions)
2-channel pen recorder, external (available via BINDER INDIVIDUAL customized solutions)
Connection kit VD with various small flange parts
Measuring access port vacuum 9 poles
Vacuum module empty (without pump)
Vacuum module with chemical membrane pump VP 1.1 (MZ2C) with separator and emission condenser,
ready for connection
3
• Ready to connect: Suction power m /h 2.0
• End vacuum mbar / inHg 7 / 0.21
• Electrical connection (50-60 Hz) V 115 / 230

VD (E2.1) 09/2018 page 78/95

Options / accessories
Vacuum module with chemical membrane pump VP 2.1 (MD4C) with separator and emission condenser,
ready for connection
3
• Ready to connect: Suction power m /h 3.4
• End vacuum mbar / inHg 1.5 / 0.04
• Electrical connection (50-60 Hz) V 115 / 230
PC 3004 Vario: Vacuum module with speed controlled chemical membrane pump VP 3.1 (MD4C Vario)
with separator and emission condenser including all necessary connection parts, and
Digital vacuum controller CVC 3000 (measuring accuracy of ≤ 1mbar / 0.03 inHg) for accurate control of
vacuum, with interface RS232 for APT-COM™ DataControlSystem software.
3
• Suction power m /h 4.6
• End vacuum mbar / inHg 1.5 / 0.04
• Electrical connection (50-60 Hz) V 115 / 230
Program controlled venting (available via BINDER INDIVIDUAL customized solutions)
Factory calibration certificate
Extension to factory calibration certificate (additional value)
Factory calibration certificate for digital object temperature display
Factory calibration certificate for digital pressure display
Extension to factory calibration certificate for digital pressure display (additional pressure)
Qualification folder
Evaporating dish with rim, small or large
Stable table on wheels with castors and locking brakes

20.4 Accessories and spare parts (extract)

BINDER GmbH is responsible for the safety features of the chamber only, provided skilled
electricians or qualified personnel authorized by BINDER perform all maintenance and repair,
and if components relating to chamber safety are replaced in the event of failure with original
spare parts. The user is responsible for any risks arising from using unauthorized
accessories/components.

Chamber size 23 53 115

Description Art. No.
Expansion rack aluminum 8009-0370 8009-0371 8009-0372
Expansion rack stainless steel 8009-0101 8009-0102 8009-0103
Door gasket silicon
6005-0015 6005-0016 6005-0018
(temperature-resistant up to 200 °C / 392°F)
Door gasket FKM
6005-0044 6005-0045 6005-0046
(temperature-resistant up to 200 °C / 392°F)
Chamber fuse 5x20 mm / 250V / 10 Amp
5006-0012 5006-0012 --
semi time lag (M)
Chamber fuse 5x20mm / 250V / 16 Amp
-- -- 5006-0013
semi time lag (M)
Safety glass panel 6012-0007 6012-0008 6012-0015
Rack holder 4005-0071 4005-0072 4005-0073

VD (E2.1) 09/2018 page 79/95

Description Art. No.
Universal centering ring 6009-0048
Straining ring 6009-0009
Blind flange 6009-0010
Handle 6002-0002
BINDER INDIVIDUAL
Protocol printer
Customized Solutions
BINDER INDIVIDUAL
2-channel pen recorder, external
Customized Solutions
Stable table on wheels with castors and locking brakes 9051-0018
Evaporating dish, small 4022-0125
Evaporating dish, large 4022-0126
Neutral cleaning agent, 1 kg 1002-0016

Validation service Art. No.

Qualification folder IQ-OQ 8012-0859
Qualification folder IQ-OQ-PQ 8012-0948
Execution of IQ-OQ DL420300
Execution of IQ-OQ-PQ DL440500

Calibration service Art. No.

Calibration of temperature including certificate (1 measuring point) DL300201
Spatial temperature measurement including certificate (9 measuring points) DL300209
Spatial temperature measurement including certificate (18 measuring points) DL300218
Spatial temperature measurement including certificate (27 measuring points) DL300227
Calibration certificate for digital pressure display DL320000
For information on components not listed here, please contact BINDER Service.

VD (E2.1) 09/2018 page 80/95

20.5 Dimensions VD 23

VD (E2.1) 09/2018 page 81/95

20.6 Dimensions VD 53

VD (E2.1) 09/2018 page 82/95

20.7 Dimensions VD 115

VD (E2.1) 09/2018 page 83/95

21. Certificates and declarations of conformity
21.1 EU Declaration of Conformity

VD (E2.1) 09/2018 page 84/95

VD (E2.1) 09/2018 page 85/95
VD (E2.1) 09/2018 page 86/95
21.2 Certificate for the GS mark of conformity of the “Deutsche Gesetzliche
Unfallversicherung e.V.“ (German Social Accident Insurance) DGUV

VD (E2.1) 09/2018 page 87/95

VD (E2.1) 09/2018 page 88/95
22. Product registration

VD (E2.1) 09/2018 page 89/95

23. Contamination clearance certificate

23.1 For chambers located outside USA and Canada

Declaration regarding safety and health

Erklärung zur Sicherheit und gesundheitlichen Unbedenklichkeit
The German Ordinance on Hazardous Substances (GefStofV), and the regulations regarding safety at the
workplace, require that this form be filled out for all products that are returned to us, so that the safety and
the health of our employees can be guaranteed.
Die Sicherheit und Gesundheit unserer Mitarbeiter, die Gefahrstoffverordnung GefStofV und die Vorschriften zur
Sicherheit am Arbeitsplatz machen es erforderlich, dass dieses Formblatt für alle Produkte, die an uns
zurückgeschickt wird.

Note: A repair is not possible without a completely filled out form.

Ohne Vorliegen des vollständig ausgefüllten Formblattes ist eine Reparatur nicht möglich.

• A completely filled out form must be transmitted via Fax (+49 (0) 7462 2005 93555) or by letter in
advance, so that this information is available before the equipment/component part arrives. A second
copy of this form must accompany the equipment/component part. In addition, the carrier should be
notified.
Eine vollständig ausgefüllte Kopie dieses Formblattes soll per Telefax (Nr. +49 (0) 7462 2005 93555) oder Brief
vorab an uns gesandt werden, so dass die Information vorliegt, bevor das Gerät/Bauteil eintrifft. Eine weitere
Kopie soll dem Gerät/Bauteil beigefügt sein. Ggf. ist auch die Spedition zu informieren.
• Incomplete information or non-conformity with this procedure will inevitably lead to substantial delays in
processing. Please understand the reason for this measure, which lies outside our area of influence,
and will help us to speed up this procedure.
Unvollständige Angaben oder Nichteinhalten dieses Ablaufs führen zwangsläufig zu beträchtlichen
Verzögerungen in der Abwicklung. Bitte haben Sie Verständnis für Maßnahmen, die außerhalb unserer
Einflussmöglichkeiten liegen und helfen Sie mit, den Ablauf beschleunigen.
• Please print and fill out this form completely.
Bitte unbedingt vollständig ausfüllen!

1. Unit/ component part / type: / Gerät / Bauteil / Typ:

2. Serial No. / Serien-Nr.:

3. Details about utilized substances / biological substances / Einzelheiten über die eingesetzten
Substanzen/biologische Materialien:
3.1 Designations / Bezeichnungen:

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

3.2 Safety measures required for handling these substances / Vorsichtsmaßnahmen beim Umgang
mit diesen Stoffen:

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

VD (E2.1) 09/2018 page 90/95

3.3 Measures to be taken in case of skin contact or release into the atmosphere / Maßnahmen
bei Personenkontakt oder Freisetzung:
a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

d) ____________________________________________________________________________

3.4 Other important information that must be taken into account / Weitere zu beachtende und
wichtige Informationen:
a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

4. Declaration on the risk of these substances (please checkmark the applicable items) /
Erklärung zur Gefährlichkeit der Stoffe (bitte Zutreffendes ankreuzen) :
 4.1 For non toxic, non radioactive, biologically harmless materials / für nicht giftige, nicht
radioaktive, biologisch ungefährliche Stoffe:
We hereby guarantee that the above-mentioned unit / component part… / Wir versichern, dass o.g.
Gerät/Bauteil...
 Has not been exposed to or contains any toxic or otherwise hazardous substances / weder giftige noch
sonstige gefährliche Stoffe enthält oder solche anhaften.
 That eventually generated reaction products are non-toxic and also do not represent a hazard / auch
evtl. entstandene Reaktionsprodukte weder giftig sind noch sonst eine Gefährdung darstellen.
 Eventual residues of hazardous substances have been removed / evtl. Rückstände von Gefahrstoffen
entfernt wurden.

 4.2 For toxic, radioactive, biologically harmful or hazardous substances, or any other
hazardous materials / für giftige, radioaktive, biologisch bedenkliche bzw. gefährliche Stoffe oder
anderweitig gefährliche Stoffe.
We hereby guarantee that … / Wir versichern, dass …
 The hazardous substances, which have come into contact with the above-mentioned
equipment/component part, have been completely listed under item 3.1 and that all information in this
regard is complete / die gefährlichen Stoffe, die mit dem o.g. Gerät/Bauteil in Kontakt kamen, in 3.1 aufgelistet
sind und alle Angaben vollständig sind.
 That the unit /component part has not been in contact with radioactivity / das Gerät/Bauteil nicht mit
Radioaktivität in Berührung kam

5. Kind of transport / transporter / Transportweg/Spediteur:

Transport by (means and name of transport company, etc.) Versendung durch (Name Spediteur o.ä.)

__________________________________________________________________________________

Date of dispatch to BINDER GmbH / Tag der Absendung an BINDER GmbH:

__________________________________________________________________________________

VD (E2.1) 09/2018 page 91/95

We hereby declare that the following measures have been taken / Wir erklären, dass folgende Maßnahmen
getroffen wurden:
 Hazardous substances were removed from the unit including component parts, so that no hazard
exists for any person in the handling or repair of these items / das Gerät/Bauteil wurde von Gefahrstoffen
befreit, so dass bei Handhabung/Reparaturen für die betreffenden Person keinerlei Gefährdung besteht
 The unit was securely packaged and properly identified / das Gerät wurde sicher verpackt und vollständig
gekennzeichnet.
 Information about the hazardousness of the shipment (if required) has been provided to the transporter
/ der Spediteur wurde (falls vorgeschrieben) über die Gefährlichkeit der Sendung informiert.
We hereby commit ourselves and guarantee that we will indemnify BINDER GmbH for all damages that
are a consequence of incomplete or incorrect information provided by us, and that we will exempt
BINDER GmbH from eventual damage claims by third parties./ Wir versichern, dass wir gegenüber BINDER
für jeden Schaden, der durch unvollständige und unrichtige Angaben entsteht, haften und BINDER gegen eventuell
entstehende Schadenansprüche Dritter freistellen.
We are aware that, in accordance with Article 823 of the German Civil Code (BGB), we are directly liable
with regard to third parties, in this instance especially the employees of BINDER GmbH, who have been
entrusted with the handling / repair of the unit / component. / Es ist uns bekannt, dass wir gegenüber Dritten –
hier insbesondere mit der Handhabung/Reparatur des Geräts/des Bauteils betraute Mitarbeiter der Firma BINDER -
gemäß §823 BGB direkt haften

Name: _______________________________________________________________________

Position/Title: _______________________________________________________________________

Date / Datum: _______________________________________________________________________

Signature / Unterschrift: _______________________________________________________________

Company stamp / Firmenstempel:

Equipment that is returned to the factory for repair must be accompanied by a completely filled
out contamination clearance certificate. For service and maintenance on site, such a
contamination clearance certificate must be submitted to the service technician before the start
of any work. No repair or maintenance of the equipment is possible, without a properly filled
out contamination clearance certificate.

VD (E2.1) 09/2018 page 92/95

23.2 For chambers located in USA and Canada

Product Return Authorization Request

Please complete this form and the Customer Decontamination Declaration (next 2 pages) and attach the
required pictures. E-mail to: [email protected]
After we have received and reviewed the complete information we will decide on the issue of a RMA
number. Please be aware that size specifications, voltage specifications as well as performance
specifications are available on the internet at www.binder-world.us at any time.
Take notice of shipping laws and regulations.

Please fill:
Reason for return request  Duplicate order
 Duplicate shipment
 Demo Page one completed by sales
 Power Plug / Voltage 115V / 230 V / 208 V / 240V
 Size does not fit space
 Transport Damage Shock watch tripped? (pictures)
 Other (specify below)
_____________________
Is there a replacement PO?  Yes  No
If yes -> PO #
If yes -> Date PO placed

Purchase order number

BINDER model number
BINDER serial number
Date unit was received

Was the unit unboxed?  Yes  No

Was the unit plugged in?  Yes  No
Was the unit in operation?  Yes  No

Pictures of unit attached?  Yes  No Pictures have to be attached!

Pictures of Packaging  Yes  No
attached?

Customer Contact Information Distributor Contact Information

Name
Company
Address
Phone
E-mail

VD (E2.1) 09/2018 page 93/95

Customer (End User) Decontamination Declaration
Health and Hazard Safety declaration

To protect the health of our employees and the safety at the workplace, we require that this form is
completed by the user for all products and parts that are returned to us. (Distributors or Service
Organizations cannot sign this form)

NO RMA number will be issued without a completed form. Products or parts returned to our
NY warehouse without a RMA number will be refused at the dock.

A second copy of the completed form must be attached to the outside of the shipping box.
1. Unit/ component part / type:

2. Serial No.

3. List any exposure to hazardous liquids, gasses or substances and radioactive material
3.1 List with MSDS sheets attached where available or needed
(if there is not enough space available below, please attach a page):

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

3.2 Safety measures required for handling the list under 3.1

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________
3.3 Measures to be taken in case of skin contact or release into the atmosphere:

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

d) ____________________________________________________________________________

3.4 Other important information that must be considered:

a) ____________________________________________________________________________

b) ____________________________________________________________________________

c) ____________________________________________________________________________

VD (E2.1) 09/2018 page 94/95

4. Declaration of Decontamination
For toxic, radioactive, biologically and chemically harmful or hazardous substances, or any other
hazardous materials.
We hereby guarantee that
4.1 Any hazardous substances, which have come into contact with the above-mentioned equipment /
component part, have been completely listed under item 3.1 and that all information in this regard is
complete.
4.2 That the unit /component part has not been in contact with radioactivity
4.3 Any Hazardous substances were removed from the unit / component part, so that no hazard exists
for a persons in the shipping, handling or repair of these returned unit
4.4 The unit was securely packaged in the original undamaged packaging and properly identified on the
outside of the packaging material with the unit designation, the RMA number and a copy of this
declaration.
4.5 Shipping laws and regulations have not been violated.
I hereby commit and guarantee that we will indemnify BINDER Inc. for all damages that are a
consequence of incomplete or incorrect information provided by us, and that we will indemnify
and hold harmless BINDER Inc. from eventual damage claims by third parties.

Name: _______________________________________________________________________

Position: _______________________________________________________________________

Company: _______________________________________________________________________

Address: _______________________________________________________________________

Phone #: _______________________________________________________________________

Email: _______________________________________________________________________

Date: _______________________________________________________________________

Signature: _______________________________________________________________________

Equipment returned to the NY warehouse for repair must be accompanied by a completed

customer decontamination declaration. For service and maintenance works on site, such a
customer decontamination declaration must be submitted to the service technician before the
start of work. No repair or maintenance of the equipment is possible without a completed form.

VD (E2.1) 09/2018 page 95/95