HCC/HCF4511B

BCD-TO-SEVEN SEGMENT LATCH/DECODER/DRIVER

. HIGH-OUTPUT-SOURCING CAPABILITY (up

.. to 25 mA)
INPUT LATCHES FOR BCD CODE STORAGE

. LAMP TEST AND BLANKING CAPABILITY

7-SEGMENT OUTPUTS BLANKED FOR BCD

. INPUT CODES > 1001

QUIESCENT CURRENT SPECIFIED TO 20V
EY F

. FOR HCC DEVICE

STANDARDIZED SYMMETRICAL OUTPUT
(Plastic Package) (Ceramic Frit Seal Package)

.. CHARACTERISTICS
5V, 10V, AND 15V PARAMETRIC RATINGS
INPUT CURRENT OF 100mA AT 18V AND 25°C

.. FOR HCC DEVICE

100% TESTED FOR QUIESCENT CURRENT
MEETS ALL REQUIREMENTS OF JEDEC TEN-
M1
(Micro Package)
C1
(Plastic Chip Carrier)

TATIVE STANDARD N° 13A, ”STANDARD SPE- ORDER CODES :

CIFICATIONS FOR DESCRIPTION OF ”B” HCC4511BF HCF4511BM1
SERIES CMOS DEVICES” HCF4511BEY HCF4511BC1

PIN CONNECTIONS

DESCRIPTION
The HCC 4511B (extended temperature range) and
the HCF 4511B (intermediate temperature range)
are monolithic integrated circuits available in 16-le-
ad dual in-line plastic or ceramic package and pla-
stic micro package.
The HCC/HCF 4511B types are BCD-to-7-segment
latch decoder drivers constructed with COS/MOS
logic and n-p-n bipolar transistor output devices on
a single monolithic structure. These devices combi-
ne the low quiescent power dissipation and high noi-
se immunity features of COS/MOS with n-p-n
bipolar output transistors capable of sourcing up to
25 mA. This capability allows the HCC/HCF 4511B
types to drive LED’s and other displays directly.
Lamp Test (LT), Blanking (BL), and Latch Enable or
Strobe inputs are provided to test the display, shut
off or intensity-modulate it, and store or strobe a
BCD code, respectively. Several different signal
may be multiplexed and displayed when external
multiplexing circuitry is used.

November 1996 1/16

HCC/HFC4511B

FUNCTIONAL DIAGRAM

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
V DD* Supply Voltage : HC C Types – 0.5 to + 20 V
H C F Types – 0.5 to + 18 V
Vi Input Voltage – 0.5 to V DD + 0.5 V
II DC Input Current (any one input) ± 10 mA
Pt ot Total Power Dissipation (per package) 200 mW
Dissipation per Output Transistor
for T o p = Full Package-temperature Range 100 mW
Top Operating Temperature : HCC Types – 55 to + 125 °C
H CF Types – 40 to + 85 °C
Tstg Storage Temperature – 65 to + 150 °C
Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functionnal operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability.
* All voltage values are referred to VSS pin voltage.

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
V DD Supply Voltage : H CC Types 3 to 18 V
H C F Types 3 to 15 V
VI Input Voltage 0 to V DD V
Top Operating Temperature : HCC Types – 55 to + 125 °C
H CF Types – 40 to + 85 °C

2/16
 HCC/HCF4511B

LOGIC DIAGRAMS

3/16
HCC/HFC4511B

TRUTH TABLE
LE BI LT D C B A a b c d e f g Display
X X 0 X X X X 1 1 1 1 1 1 1 8
X 0 1 X X X X 0 0 0 0 0 0 0 Blank
0 1 1 0 0 0 0 1 1 1 1 1 1 0
0
0 1 1 0 0 0 1 0 1 1 0 0 0 0 1
0 1 1 0 0 1 0 1 1 0 1 1 0 1 2
0 1 1 0 0 1 1 1 1 1 1 0 0 1 3
0 1 1 0 1 0 0 0 1 1 0 0 1 1 4
0 1 1 0 1 0 1 1 0 1 1 0 1 1 5
0 1 1 0 1 1 0 0 0 1 1 1 1 1 6
0 1 1 0 1 1 1 1 1 1 0 0 0 0 7
0 1 1 1 0 0 0 1 1 1 1 1 1 1 8
0 1 1 1 0 0 1 1 1 1 0 0 1 1 9
0 1 1 1 0 1 0 0 0 0 0 0 0 0 Blank
0 1 1 1 0 1 1 0 0 0 0 0 0 0 Blank
0 1 1 1 1 0 0 0 0 0 0 0 0 0 Blank
0 1 1 1 1 0 1 0 0 0 0 0 0 0 Blank
0 1 1 1 1 1 0 0 0 0 0 0 0 0 Blank
0 1 1 1 1 1 1 0 0 0 0 0 0 0 Blank
1 1 1 X X X X * *

4/16
 HCC/HCF4511B

STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions)

Test Conditions Value
Symbol Parameter VI VO |I O | V D D T L o w* 25 °C T Hi g h * Unit
(V) (V) (µA) (V) Min. Max. Min. Typ. Max. Min. Max.

IL Quiescent 0/ 5 5 5 0.04 5 150

Current 0/10 10 10 0.04 10 300
HCC
Types 0/15 15 20 0.04 20 600
0/20 20 100 0.08 100 3000 µA
0/ 5 5 20 0.04 20 150
HCF
0/10 10 40 0.04 40 300
Types
0/15 15 80 0.04 80 600
V OH Output High 0/ 5 5 4 4.1 4.55 4.2
Voltage 0/10 10 9 9.1 9.55 9.2 V
0/15 15 14 14.1 14.55 14.2
V OL Output Low 5/0 5 0.05 0.05 0.05
Voltage 10/0 10 0.05 0.05 0.05 V
15/0 15 0.05 0.05 0.05
V IH Input High 0.5/3.8 5 3.5 3.5 3.5
Voltage 1/8.8 10 7 7 7 V
1.5/13.8 15 11 11 11
V IL Input Low 3.8/0.5 5 1.5 1.5 1.5
Voltage 8.8/1 10 3 3 3 V
13.8/1.5 15 4 4 4
V OH Output HCC 0 4.1 4.10 4.55 4.20
Drive Types 5 4.25
Voltage
10 3.80 3.90 4.10 3.90
5 V
15 3.95
20 3.55 3.40 3.75
25 3.40 3.10 3.55
0 9 9.10 9.55 9.20
5 9.25
10 8.85 9 9.15
10 V
15 9.05
20 8.70 8.60 8.90 8.40
25 8.60 8.30 8.75
0 14 14.10 14.55 14.20
5 14.30
10 13.90 14 14.20 14
15 V
15 14.10
20 13.75 13.70 13.95 13.50
25 13.65 13.50 13.80 13.10
* TLow= – 55°C for HCC device : – 40°C for HCF device.
* THigh= + 125°C for HCC device : + 85°C for HCF device.
The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5 V min. with VDD = 15V.

5/16
HCC/HFC4511B

STATIC ELECTRICAL CHARACTERISTICS (continued)

Test Conditions Value
Symbol Parameter VI VO |I O | V D D T L o w* 25 °C T Hi g h * Unit
(V) (V) (µA) (V) Min. Max. Min. Typ. Max. Min. Max.

V OH Output 0 4.1 4.1 4.57 4.1

Drive 5 4.24
Voltage
10 3.6 3.6 4.12 3.3
5 V
15 3.94
20 2.8 2.8 3.75 2.5
25 3.54
0 9.1 9.1 9.58 9.1
5 9.26
HCF 10 8.75 8.75 9.17 8.45
Types 10 V
15 9.04
20 8.1 8.1 8.90 7.8
25 8.75
0 14.1 14.1 14.59 14.1
5 14.27
10 13.75 13.75 14.18 13.45
15 V
15 14.07
20 13.1 13.1 13.95 12.8
25 13.80
I OL Output 0/ 5 0.4 5 0.64 0.51 1 0.36
Sink HCC
0/10 0.5 10 1.6 1.3 2.6 0.9
Current Types
0/15 1.5 15 4.2 3.4 6.8 2.4
0/ 5 0.4 5 0.52 0.44 1 0.36 mA
HCF
0/10 0.5 10 1.3 1.1 2.6 0.9
Types
0/15 1.5 15 3.6 3 6.8 2.4
I IH , I IL Input HCC 0/18 18 ± 0.1 ±10 – 5 ± 0.1 ±1
Leakage Types
Current
Any Input µA
HCF
15 ±0.3 ±10 – 5 ± 0.3 ± 1
Types 0/15
CI Input Capacitance Any Input 5 7.5 pF
* TLow= – 55°C for HCC device : – 40°C for HCF device.
* THigh= + 125°C for HCC device : + 85°C for HCF device.
The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5 V min. with VDD = 15V.

6/16
 HCC/HCF4511B

DYNAMIC ELECTRICAL CHARACTERISTICS (Tamb = 25 o C, C L = 50 pF, RL = 200 KΩ,

o
typical temperature coefficent for all VDD values is 03 %/ C, all input rise and fall times= 20 ns)
Test Conditions Value
Symbol Parameter Unit
VDD (V) Min. Typ. Max.
tPHL Propagation Delay Time (data) 5 520 1040
10 210 420 ns
15 150 300
tPLH Propagation Delay Time (data) 5 660 1320
10 260 520 ns
15 180 360
tPHL Propagation Delay Time (BL) 5 350 700
10 175 350 ns
15 125 250
tPLH Propagation Delay Time (BL) 5 400 800
10 175 350 ns
15 150 300
tPHL Propagation Delay Time (LT) 5 250 500
10 125 250 ns
15 85 170
tPLH Propagation Delay Time (LT) 5 150 300
10 75 150 ns
15 50 100
tTLH Transition Time 5 40 80
10 30 60 ns
15 20 40
tTHL Transition Time 5 125 310
10 75 185 ns
15 65 160
tsetup Setup Time 5 150 75
10 70 35 ns
15 40 20
thold Hold Time 5 0 -75
10 0 -35 ns
15 0 -20
tW Strobe Pulse Width 5 400 200
10 160 80 ms
15 100 50

7/16
HCC/HFC4511B

Typical Output Low (sink) Current Characteristics. Typical data-to-output, low-to-high-level propaga-
tion delay time as a function of load capacitance.

Typical data-to-output, high-to-low-level propaga- Typical low-to-high level transition ime as a func-
tion delay time as a function of load capacitance. tion of load capacitance.

Typical high-to-low level transition ime as a func- Typical Voltage drop (VDD to output) vs. Output
tion of load capacitance. source Current as a Function of Supply.

8/16
 HCC/HCF4511B

Typical Dynamic Power Dissipation Charac- Derated Static Output Current Per Output.
teristics.

Maximum continuous derated output current IOH applies to a single

output with all other outputs sourcing an equal amount of current at
the supply voltages shown. Operation above the derating curve is
not recommenced.

TYPICAL APPLICATIONS (interfacing with various displays)

DRIVING COMMON-CATHODE 7-SEGMENT LED DISPLAYS

9/16
HCC/HFC4511B

TYPICAL APPLICATIONS (continued)

Driving Low-voltage Fluorescent Displays. Driving Incandescent Displays.

2 of 7 Segments Shown Connected

A medium-brightness intensity display can be obtained with low- Resistors R from VDD VDD to each 7-segment driver output
voltage fluorescent displays such as the Tung-Sot Digivac S/G are choosen to keep all Numitron segments slightly on and
series. warm.

TEST CIRCUITS
Quiescent Device Current. Noise Immunity.

Input Leakage Current. Data Propagation Delay.

10/16
 HCC/HCF4511B

TEST CIRCUITS (continued)

Dynamic Power dissipation.

11/16
HCC/HFC4511B

Plastic DIP16 (0.25) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 0.77 1.65 0.030 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 17.78 0.700

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 0.050

P001C

12/16
 HCC/HCF4511B

Ceramic DIP16/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7 0.276

D 3.3 0.130

E 0.38 0.015

e3 17.78 0.700

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 0.51 1.27 0.020 0.050

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053D

13/16
HCC/HFC4511B

SO16 (Narrow) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8° (max.)

P013H

14/16
 HCC/HCF4511B

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

15/16
HCC/HFC4511B

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1996 SGS-THOMSON Microelectronics - Printed in Italy - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
.

16/16