TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Disassembly
Chapter 1, Removing the Battery Pack
To remove the battery pack from the battery bay,
follow the steps below:
1. Turn the notebook upside down.
2. Slide the battery lock in the direction of the
arrow to unlock the battery pack
3. Slide the battery release latch in the direction
of the arrow. The battery pack wills pop-up
automatically. Gently pry the battery pack
from its housing
NOTE: Always start laptop disassembly by
removing the battery pack first.
Page 1 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 2, Removing Memory
To remove the bottom cover, follow the steps below:
1. Remove the two screws pads as shown
2. Remove the two screws securing the Memory
cover as show
3. Open the Bottom case from left side.
Warning: Be care full Lift off the Memory
Cover can cause permanent damage for the
lower logic.
Page 2 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
4. Push the latches to release the RAM module.
A spring will force one end of the module up
5. Grasp the memory module and remove from
main board.
Chapter 3, Removing the SSD Module
To remove the SSD Module, follow the steps below:
1. Remove the isolation tape.
2. Lever up with thumb the connector bracket
and disconnect the SSD Module cable from
the motherboard
3. Lift off the cable
Page 3 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
4. Remove the two screws with screw driver to
remove the SSD Module from motherboard
5. Lift off the SSD Module form bottom casing
6. Remove the isolation tape.
7. Lever up with thumb the connector bracket
and disconnect the SSD Module cable from
SSD Card
8. Lift off the cable
Page 4 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 4, Removing the Keyboard
To remove the keyboard, follow the steps below:
1. Remove the screw pads as shown
2. Remove the two screws securing the
keyboard to the logic lower.
Page 5 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
1. Turn the notebook over and push the latches
to release the keyboard
2. Pull the keyboard towards you, revealing the
keyboard cable underneath
3. lever up with thumb the connector bracket
and disconnect the keyboard cable from the
motherboard
4. Lift off the cable and remove the keyboard
Page 6 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 5, Removing the LCD Module
To remove the LCD Module, first remove the
battery pack, Logic Lower, Follow the steps below
to remove from the main board.
1. Remove the four screws securing the main
board to the logic upper.
2. Remove the metal plate.
Note : Please remember the position four
screws, installing wrong screw can cause
permanent damage for logic upper
3. Remove the cover hinge as show
4. Disconnect the CMOS, Speaker, LCD,
Antenna Wifi cable as shown
Page 7 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
5. Release all the cable from logic lower
6. Remove the six screws securing the LCD
7. Remove the hand grip notebook as show
8. Remove the two screws securing the LCD
module
Page 8 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
9. Gently remove the LCD Module
Page 9 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 6, Removing Keyboard Frame
To remove the Keyboard frame, first remove the
battery pack, LCD Module. Follow the steps below
to remove the Keyboard frame.
1. Remove the six screw pads as show.
2. Remove the ten screws securing the Logic
upper to the logic lower.
3. Remove the four screw pads as shown
4. Turn the notebook over
5. lever up with thumb the connector bracket
and disconnect the Touchpad and Touchpad
button cable from the motherboard
6. Remove The Screw securing the Logic upper
to the logic lower.
7. Gently remove the Keyboard frame
Warning: Be care full Lift off the keyboard frame
can cause permanent damage for the lower logic.
Page 10 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 7, Removing Touchpad Button
To remove the Touchpad Button. Follow the steps
below
1. Turn the Keyboard frame notebook upside
down.
2. Remove the three screw securing touchpad
frame to the logic upper.
Note : Please remember the position three
screws, installing wrong screw can cause permanent
damage for logic upper
3. Gently remove the touchpad button as show
NOTE: The touchpad module is attached to the rear of the logic upper and cannot be removed.
Page 11 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 8, Disassembly the Mainboard
To disassemble the Mainboard. Then follow these steps:
1. Remove the screw securing mainboard to the
logic lower as shown
2. Disconnect the Microphone cable as show
3. Gently remove the mainboard from the logic
lower.
4. Discconect the CMOS Battery
Warning: Be care full Lift off the LCD bezel can
cause permanent damage for the upper logic,
please attention for the key as show.
Chapter 9, Disassembly the Wifi Module
To disassemble the Wifi . Then follow these steps:
1. Turn over the Mainboard
2. Remove the screw securing the wifi to the
mainboard
3. Grasp the Wifi module and remove from
mainboard
Page 12 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 10, Disassembly the cooler fan
To disassemble the cooler fan. Then follow these
steps:
1. Disconnect the Fan cable as show
2. Remove the two screws securing the cooler fan
the mainboard.
3. Gently remove the cooler fan
Chapter 11, Disassembly the Display
To disassemble the display. Then follow these steps:
5. Remove the six screw pads as shown
Page 13 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
6. Remove the six screws securing the LCD
bezel to the LCD module.
7. Carefully insert your fingers between the
display and the LCD bezel as indicated by
the arrow, and gently pry up the LCD bezel.
Warning: Be care full Lift off the LCD bezel
can cause permanent damage for the upper logic,
please attention for the key as show.
8. Remove the four screws mounting the
display.
9. Disconnect the Touch Screen cable as show.
10. Pull the keyboard towards you, revealing the
LVDS cable underneath
Page 14 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
11. Remove the LVDS cable isolation tape
12. Disconnect the LVDS cable from the back of
the LCD.
13. Gently lift out the display. Remove the four
screws securing the hinges to the display.
Chapter 12, Removing Camera Module
To remove the camera module, first remove the LCD
module and lift out LCD display. Then follow these
steps:
1. Remove the two screws securing the CMOS
module to the LCD Frame
Page 15 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
2. Remove the Upper case CMOC module as
show
3. Disconnect the CMOS cable from the CMOS
module as shown.
4. Gently remove the CMOS module from LCD
Frame
5. Remove the two screws securing CMOS
module to the CMOS case as show
6. Gently remove the CMOS module from
CMOS module.
Page 16 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 13, Removing LCD Button Board
To remove the LCD Button board, first remove the
LCD module and lift out LCD display. Then follow
these steps:
1. Remove the two screw securing LCD button
as show
2. Remove the LCD Button board
3. Disconnect The LCD Button Board cable as
show
4. Lift off the LCD Button Board.
Page 17 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 14, Removing the Speaker
To remove the speaker, first remove the LCD frame
and inverter Then follow the steps below
1. Remove the four screws securing the
speakers to the LCD module.
2. Lift out the speaker as shown.
3. Remove the two screws securing hinge to
the LCD frame
Page 18 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
4. Remove the hinge with minus screw driver
as snow.
5. Remove the speaker cable from hinge as
show.
Assembly
Chapter 15, Assembly the Speaker
To assembly the speaker, follow the steps below
1. Remove the speaker cable from hinge as
show
Page 19 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
2. Install the LCD Hinge cover to the LCD
hinge.
3. Tight the two screws securing hinge to the
LCD frame.
4. Tight the four screw securing speaker to the
LCD frame.
Chapter 16, Assembly LCD Button Board
To assembly the LCD Button board follow these
steps:
1. Connect The LCD Button Board cable as
show
2. Install the LCD Button Board
3. Tight the two screw securing LCD button as
show
Page 20 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 17, Assembly Camera Module
To assembly the camera module, follow these steps:
1. Tight the two screws securing CMOS module
to the CMOS case as show
2. Connect the CMOS cable to the CMOS
module as shown.
3. Gently install the CMOS module to CMOS
Frame
4. Tight the two screws securing the CMOS
module to the LCD Frame
Chapter 18, Assembly the Display
To assemble the display. Then follow these steps:
1. Tight the four screws securing the hinges to
the display.
Page 21 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
2. Connect the LVDS cable from the back of the
LCD.
3. Tight the LVDS cable isolation tape
4. Tight the four screws mounting the display.
5. Connect the Touch Screen cable as show.
6. Gently pry down the LCD bezel to the LCD
Module.
7. Tight the six screw securing the LC bezel to
the LCD module as shown
8. Install the six screw pads as shown
Page 22 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 19, Assembly the cooler fan
To disassemble the cooler fan. Then follow these
steps:
1. Tight the two screws securing the cooler fan
the mainboard.
2. Connect the Fan cable as show
Chapter 20, Assembly the Wifi Module
To assemble the Wifi. Then follow these steps:
1. Push Wireless LAN at 30’ form main board,
push down and tight the screw
Page 23 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 21, Assembly the Mainboard
To Assemble the Mainboard. follow these steps:
1. Connect the CMOS Battery
2. Install the mainboard to the logic lower
3. Tight the screw securing the mainboard to
the logic lower
4. Connect the Microphone cable as show
Warning: Be care full Lift in the Mainboard can
cause permanent damage for button pin and please
intention for key as show.
Chapter 22, Assembly Touchpad Button
To Assembly the Touchpad Button. Follow the steps
below
4. Install the touchpad button
5. Tight the three screw securing touchpad
frame to the logic upper.
Note : Please remember the position three
screws, installing wrong screw can cause permanent
damage for logic upper
Page 24 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 23, Assembly Keyboard Frame
To assembly the Keyboard frames. Follow the steps
below.
1. Connect the Touchpad and Touchpad button
cable to from the motherboard
2. Tight The Screw securing the Logic upper to
the logic lower.
3. Turn the notebook upside down.
4. Tight the ten screws securing the Logic upper
to the logic lower.
5. Install the six screw pads as show.
Page 25 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 24, Assembly the LCD Module
To assembly the LCD Module to the notebook,
Follow the steps below;
1. Gently install the LCD Module
2. Tight the two screws securing the LCD
module
10. Tight the six screws securing the LCD
11. Tight the hand grip notebook as show
Page 26 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
3. Connect the CMOS, Speaker, LCD, Antenna
Wifi cable as shown
4. Install the cover hinge as show
5. Install the metal plate.
6. Tight the four screws securing the main
board to the logic upper.
Note : Please remember the position four
screws, installing wrong screw can cause
permanent damage for logic upper
Page 27 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
Chapter 25, Assembly the Keyboard
To Assembly the keyboard follow the step;
1. Lift in the cable and connect the keyboard
cable to the motherboard
2. Push the keyboard until latches at position
lock
3. Turn the notebook over and tight the two
screw securing the keyboard to the logic
lower.
Page 28 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
4. Install the screw pads as shown
Chapter 26, Assembly the SSD Module
To Assembly the SSD Module, follow the steps
below:
1. Lift in the cable
2. Connect the SSD Module cable to SSD Card
3. Install the isolation tape.
4. Lift in the SSD Module form bottom casing
5. Tight the two screws with screw driver to
remove the SSD Module from motherboard
Page 29 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
6. Connect the SSD Module cable to the
motherboard
7. Install the isolation tape.
Chapter 27, Assembly Memory
To assembly the bottom cover, follow the steps
below
1. Push memory at 30’ form main board and
push down until the Key at position lock
2. Key at Lock position, if the installation
corrects the pin will be invisible
Page 30 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
3. Close the Memory and SSD cover
4. Tight the two screws securing the Memory
cover as show
5. Install the two screws pads as shown
Chapter 28, Assembly the Battery Pack
To install the battery pack to the battery bay, follow
the steps below:
1. Slide the battery lock latch in the direction of
the arrow. The battery lock wills pop-up
automatically.
Page 31 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009
2. Lock the secondary lock as show for more
safety
Page 32 of 32
